diff options
Diffstat (limited to 'drivers/tty/serial/8250')
| -rw-r--r-- | drivers/tty/serial/8250/8250_exar.c | 7 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_fintek.c | 5 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_men_mcb.c | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_mtk.c | 162 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/Kconfig | 1 |
5 files changed, 149 insertions, 27 deletions
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c index 0089aa305ef9..edd6dfe055bf 100644 --- a/drivers/tty/serial/8250/8250_exar.c +++ b/drivers/tty/serial/8250/8250_exar.c @@ -361,12 +361,15 @@ static const struct exar8250_platform iot2040_platform = { .register_gpio = iot2040_register_gpio, }; +/* + * For SIMATIC IOT2000, only IOT2040 and its variants have the Exar device, + * IOT2020 doesn't have. Therefore it is sufficient to match on the common + * board name after the device was found. + */ static const struct dmi_system_id exar_platforms[] = { { .matches = { DMI_EXACT_MATCH(DMI_BOARD_NAME, "SIMATIC IOT2000"), - DMI_EXACT_MATCH(DMI_BOARD_ASSET_TAG, - "6ES7647-0AA00-1YA2"), }, .driver_data = (void *)&iot2040_platform, }, diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c index 79a4958b3f5c..31c91c2f8c6e 100644 --- a/drivers/tty/serial/8250/8250_fintek.c +++ b/drivers/tty/serial/8250/8250_fintek.c @@ -303,8 +303,9 @@ static void fintek_8250_goto_highspeed(struct uart_8250_port *uart, } } -void fintek_8250_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) +static void fintek_8250_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) { struct fintek_8250 *pdata = port->private_data; unsigned int baud = tty_termios_baud_rate(termios); diff --git a/drivers/tty/serial/8250/8250_men_mcb.c b/drivers/tty/serial/8250/8250_men_mcb.c index 127017cc41d9..02c5aff58a74 100644 --- a/drivers/tty/serial/8250/8250_men_mcb.c +++ b/drivers/tty/serial/8250/8250_men_mcb.c @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0 #include <linux/device.h> #include <linux/kernel.h> #include <linux/module.h> diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index c1fdbc0b6840..417c7c810df9 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -21,15 +21,32 @@ #include "8250.h" -#define UART_MTK_HIGHS 0x09 /* Highspeed register */ -#define UART_MTK_SAMPLE_COUNT 0x0a /* Sample count register */ -#define UART_MTK_SAMPLE_POINT 0x0b /* Sample point register */ +#define MTK_UART_HIGHS 0x09 /* Highspeed register */ +#define MTK_UART_SAMPLE_COUNT 0x0a /* Sample count register */ +#define MTK_UART_SAMPLE_POINT 0x0b /* Sample point register */ #define MTK_UART_RATE_FIX 0x0d /* UART Rate Fix Register */ - +#define MTK_UART_ESCAPE_DAT 0x10 /* Escape Character register */ +#define MTK_UART_ESCAPE_EN 0x11 /* Escape Enable register */ #define MTK_UART_DMA_EN 0x13 /* DMA Enable register */ +#define MTK_UART_RXTRI_AD 0x14 /* RX Trigger address */ +#define MTK_UART_FRACDIV_L 0x15 /* Fractional divider LSB address */ +#define MTK_UART_FRACDIV_M 0x16 /* Fractional divider MSB address */ +#define MTK_UART_IER_XOFFI 0x20 /* Enable XOFF character interrupt */ +#define MTK_UART_IER_RTSI 0x40 /* Enable RTS Modem status interrupt */ +#define MTK_UART_IER_CTSI 0x80 /* Enable CTS Modem status interrupt */ + +#define MTK_UART_EFR_EN 0x10 /* Enable enhancement feature */ +#define MTK_UART_EFR_RTS 0x40 /* Enable hardware rx flow control */ +#define MTK_UART_EFR_CTS 0x80 /* Enable hardware tx flow control */ +#define MTK_UART_EFR_NO_SW_FC 0x0 /* no sw flow control */ +#define MTK_UART_EFR_XON1_XOFF1 0xa /* XON1/XOFF1 as sw flow control */ +#define MTK_UART_EFR_XON2_XOFF2 0x5 /* XON2/XOFF2 as sw flow control */ +#define MTK_UART_EFR_SW_FC_MASK 0xf /* Enable CTS Modem status interrupt */ +#define MTK_UART_EFR_HW_FC (MTK_UART_EFR_RTS | MTK_UART_EFR_CTS) #define MTK_UART_DMA_EN_TX 0x2 #define MTK_UART_DMA_EN_RX 0x5 +#define MTK_UART_ESCAPE_CHAR 0x77 /* Escape char added under sw fc */ #define MTK_UART_TX_SIZE UART_XMIT_SIZE #define MTK_UART_RX_SIZE 0x8000 #define MTK_UART_TX_TRIGGER 1 @@ -46,6 +63,7 @@ enum dma_rx_status { struct mtk8250_data { int line; unsigned int rx_pos; + unsigned int clk_count; struct clk *uart_clk; struct clk *bus_clk; struct uart_8250_dma *dma; @@ -54,6 +72,13 @@ struct mtk8250_data { #endif }; +/* flow control mode */ +enum { + MTK_UART_FC_NONE, + MTK_UART_FC_SW, + MTK_UART_FC_HW, +}; + #ifdef CONFIG_SERIAL_8250_DMA static void mtk8250_rx_dma(struct uart_8250_port *up); @@ -192,13 +217,89 @@ static void mtk8250_shutdown(struct uart_port *port) return serial8250_do_shutdown(port); } +static void mtk8250_disable_intrs(struct uart_8250_port *up, int mask) +{ + serial_out(up, UART_IER, serial_in(up, UART_IER) & (~mask)); +} + +static void mtk8250_enable_intrs(struct uart_8250_port *up, int mask) +{ + serial_out(up, UART_IER, serial_in(up, UART_IER) | mask); +} + +static void mtk8250_set_flow_ctrl(struct uart_8250_port *up, int mode) +{ + struct uart_port *port = &up->port; + int lcr = serial_in(up, UART_LCR); + + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, UART_EFR_ECB); + serial_out(up, UART_LCR, lcr); + lcr = serial_in(up, UART_LCR); + + switch (mode) { + case MTK_UART_FC_NONE: + serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); + serial_out(up, MTK_UART_ESCAPE_EN, 0x00); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + serial_out(up, UART_EFR, serial_in(up, UART_EFR) & + (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK))); + serial_out(up, UART_LCR, lcr); + mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI | + MTK_UART_IER_RTSI | MTK_UART_IER_CTSI); + break; + + case MTK_UART_FC_HW: + serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); + serial_out(up, MTK_UART_ESCAPE_EN, 0x00); + serial_out(up, UART_MCR, UART_MCR_RTS); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + + /*enable hw flow control*/ + serial_out(up, UART_EFR, MTK_UART_EFR_HW_FC | + (serial_in(up, UART_EFR) & + (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); + + serial_out(up, UART_LCR, lcr); + mtk8250_disable_intrs(up, MTK_UART_IER_XOFFI); + mtk8250_enable_intrs(up, MTK_UART_IER_CTSI | MTK_UART_IER_RTSI); + break; + + case MTK_UART_FC_SW: /*MTK software flow control */ + serial_out(up, MTK_UART_ESCAPE_DAT, MTK_UART_ESCAPE_CHAR); + serial_out(up, MTK_UART_ESCAPE_EN, 0x01); + serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B); + + /*enable sw flow control */ + serial_out(up, UART_EFR, MTK_UART_EFR_XON1_XOFF1 | + (serial_in(up, UART_EFR) & + (~(MTK_UART_EFR_HW_FC | MTK_UART_EFR_SW_FC_MASK)))); + + serial_out(up, UART_XON1, START_CHAR(port->state->port.tty)); + serial_out(up, UART_XOFF1, STOP_CHAR(port->state->port.tty)); + serial_out(up, UART_LCR, lcr); + mtk8250_disable_intrs(up, MTK_UART_IER_CTSI|MTK_UART_IER_RTSI); + mtk8250_enable_intrs(up, MTK_UART_IER_XOFFI); + break; + default: + break; + } +} + static void mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { + unsigned short fraction_L_mapping[] = { + 0, 1, 0x5, 0x15, 0x55, 0x57, 0x57, 0x77, 0x7F, 0xFF, 0xFF + }; + unsigned short fraction_M_mapping[] = { + 0, 0, 0, 0, 0, 0, 1, 1, 1, 1, 3 + }; struct uart_8250_port *up = up_to_u8250p(port); + unsigned int baud, quot, fraction; unsigned long flags; - unsigned int baud, quot; + int mode; #ifdef CONFIG_SERIAL_8250_DMA if (up->dma) { @@ -214,7 +315,7 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, serial8250_do_set_termios(port, termios, old); /* - * Mediatek UARTs use an extra highspeed register (UART_MTK_HIGHS) + * Mediatek UARTs use an extra highspeed register (MTK_UART_HIGHS) * * We need to recalcualte the quot register, as the claculation depends * on the vaule in the highspeed register. @@ -230,18 +331,11 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, port->uartclk / 16 / UART_DIV_MAX, port->uartclk); - if (baud <= 115200) { - serial_port_out(port, UART_MTK_HIGHS, 0x0); + if (baud < 115200) { + serial_port_out(port, MTK_UART_HIGHS, 0x0); quot = uart_get_divisor(port, baud); - } else if (baud <= 576000) { - serial_port_out(port, UART_MTK_HIGHS, 0x2); - - /* Set to next lower baudrate supported */ - if ((baud == 500000) || (baud == 576000)) - baud = 460800; - quot = DIV_ROUND_UP(port->uartclk, 4 * baud); } else { - serial_port_out(port, UART_MTK_HIGHS, 0x3); + serial_port_out(port, MTK_UART_HIGHS, 0x3); quot = DIV_ROUND_UP(port->uartclk, 256 * baud); } @@ -258,18 +352,40 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, /* reset DLAB */ serial_port_out(port, UART_LCR, up->lcr); - if (baud > 460800) { + if (baud >= 115200) { unsigned int tmp; - tmp = DIV_ROUND_CLOSEST(port->uartclk, quot * baud); - serial_port_out(port, UART_MTK_SAMPLE_COUNT, tmp - 1); - serial_port_out(port, UART_MTK_SAMPLE_POINT, - (tmp - 2) >> 1); + tmp = (port->uartclk / (baud * quot)) - 1; + serial_port_out(port, MTK_UART_SAMPLE_COUNT, tmp); + serial_port_out(port, MTK_UART_SAMPLE_POINT, + (tmp >> 1) - 1); + + /*count fraction to set fractoin register */ + fraction = ((port->uartclk * 100) / baud / quot) % 100; + fraction = DIV_ROUND_CLOSEST(fraction, 10); + serial_port_out(port, MTK_UART_FRACDIV_L, + fraction_L_mapping[fraction]); + serial_port_out(port, MTK_UART_FRACDIV_M, + fraction_M_mapping[fraction]); } else { - serial_port_out(port, UART_MTK_SAMPLE_COUNT, 0x00); - serial_port_out(port, UART_MTK_SAMPLE_POINT, 0xff); + serial_port_out(port, MTK_UART_SAMPLE_COUNT, 0x00); + serial_port_out(port, MTK_UART_SAMPLE_POINT, 0xff); + serial_port_out(port, MTK_UART_FRACDIV_L, 0x00); + serial_port_out(port, MTK_UART_FRACDIV_M, 0x00); } + if ((termios->c_cflag & CRTSCTS) && (!(termios->c_iflag & CRTSCTS))) + mode = MTK_UART_FC_HW; + else if (termios->c_iflag & CRTSCTS) + mode = MTK_UART_FC_SW; + else + mode = MTK_UART_FC_NONE; + + mtk8250_set_flow_ctrl(up, mode); + + if (uart_console(port)) + up->port.cons->cflag = termios->c_cflag; + spin_unlock_irqrestore(&port->lock, flags); /* Don't rewrite B0 */ if (tty_termios_baud_rate(termios)) diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index 15c2c5463835..296115f6a4d8 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -1,3 +1,4 @@ +# SPDX-License-Identifier: GPL-2.0 # # The 8250/16550 serial drivers. You shouldn't be in this list unless # you somehow have an implicit or explicit dependency on SERIAL_8250. |