diff options
Diffstat (limited to 'drivers/spi')
| -rw-r--r-- | drivers/spi/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 1 | ||||
| -rw-r--r-- | drivers/spi/spi_butterfly.c | 1 | ||||
| -rw-r--r-- | drivers/spi/spi_s3c24xx_gpio.c | 188 |
4 files changed, 198 insertions, 0 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 3867c6ef24f3..c60dacfaadd2 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -95,6 +95,14 @@ config SPI_PXA2XX The driver can be configured to use any SSP port and additional documentation can be found a Documentation/spi/pxa2xx. +config SPI_S3C24XX_GPIO + tristate "Samsung S3C24XX series SPI by GPIO" + depends on SPI_MASTER && ARCH_S3C2410 && SPI_BITBANG && EXPERIMENTAL + help + SPI driver for Samsung S3C24XX series ARM SoCs using + GPIO lines to provide the SPI bus. This can be used where + the inbuilt hardware cannot provide the transfer mode, or + where the board is using non hardware connected pins. # # Add new SPI master controllers in alphabetical order above this line # diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 5a410caa03c7..4dc82c93bfe6 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o obj-$(CONFIG_SPI_PXA2XX) += pxa2xx_spi.o obj-$(CONFIG_SPI_MPC83xx) += spi_mpc83xx.o +obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o # ... add above this line ... # SPI protocol drivers (device/link on bus) diff --git a/drivers/spi/spi_butterfly.c b/drivers/spi/spi_butterfly.c index ff9e5faa4dc9..a006a1ee27ac 100644 --- a/drivers/spi/spi_butterfly.c +++ b/drivers/spi/spi_butterfly.c @@ -321,6 +321,7 @@ static void butterfly_attach(struct parport *p) * (firmware resets at45, acts as spi slave) or neither (we ignore * both, AVR uses AT45). Here we expect firmware for the first option. */ + pp->info[0].max_speed_hz = 15 * 1000 * 1000; strcpy(pp->info[0].modalias, "mtd_dataflash"); pp->info[0].platform_data = &flash; diff --git a/drivers/spi/spi_s3c24xx_gpio.c b/drivers/spi/spi_s3c24xx_gpio.c new file mode 100644 index 000000000000..aacdceb8f44b --- /dev/null +++ b/drivers/spi/spi_s3c24xx_gpio.c @@ -0,0 +1,188 @@ +/* linux/drivers/spi/spi_s3c24xx_gpio.c + * + * Copyright (c) 2006 Ben Dooks + * Copyright (c) 2006 Simtec Electronics + * + * S3C24XX GPIO based SPI driver + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * +*/ + +#include <linux/config.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/spinlock.h> +#include <linux/platform_device.h> + +#include <linux/spi/spi.h> +#include <linux/spi/spi_bitbang.h> + +#include <asm/arch/regs-gpio.h> +#include <asm/arch/spi-gpio.h> +#include <asm/arch/hardware.h> + +struct s3c2410_spigpio { + struct spi_bitbang bitbang; + + struct s3c2410_spigpio_info *info; + struct platform_device *dev; +}; + +static inline struct s3c2410_spigpio *spidev_to_sg(struct spi_device *spi) +{ + return spi->controller_data; +} + +static inline void setsck(struct spi_device *dev, int on) +{ + struct s3c2410_spigpio *sg = spidev_to_sg(dev); + s3c2410_gpio_setpin(sg->info->pin_clk, on ? 1 : 0); +} + +static inline void setmosi(struct spi_device *dev, int on) +{ + struct s3c2410_spigpio *sg = spidev_to_sg(dev); + s3c2410_gpio_setpin(sg->info->pin_mosi, on ? 1 : 0); +} + +static inline u32 getmiso(struct spi_device *dev) +{ + struct s3c2410_spigpio *sg = spidev_to_sg(dev); + return s3c2410_gpio_getpin(sg->info->pin_miso) ? 1 : 0; +} + +#define spidelay(x) ndelay(x) + +#define EXPAND_BITBANG_TXRX +#include <linux/spi/spi_bitbang.h> + + +static u32 s3c2410_spigpio_txrx_mode0(struct spi_device *spi, + unsigned nsecs, u32 word, u8 bits) +{ + return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits); +} + +static u32 s3c2410_spigpio_txrx_mode1(struct spi_device *spi, + unsigned nsecs, u32 word, u8 bits) +{ + return bitbang_txrx_be_cpha1(spi, nsecs, 0, word, bits); +} + +static void s3c2410_spigpio_chipselect(struct spi_device *dev, int value) +{ + struct s3c2410_spigpio *sg = spidev_to_sg(dev); + + if (sg->info && sg->info->chip_select) + (sg->info->chip_select)(sg->info, value); +} + +static int s3c2410_spigpio_probe(struct platform_device *dev) +{ + struct spi_master *master; + struct s3c2410_spigpio *sp; + int ret; + int i; + + master = spi_alloc_master(&dev->dev, sizeof(struct s3c2410_spigpio)); + if (master == NULL) { + dev_err(&dev->dev, "failed to allocate spi master\n"); + ret = -ENOMEM; + goto err; + } + + sp = spi_master_get_devdata(master); + + platform_set_drvdata(dev, sp); + + /* copy in the plkatform data */ + sp->info = dev->dev.platform_data; + + /* setup spi bitbang adaptor */ + sp->bitbang.master = spi_master_get(master); + sp->bitbang.chipselect = s3c2410_spigpio_chipselect; + + sp->bitbang.txrx_word[SPI_MODE_0] = s3c2410_spigpio_txrx_mode0; + sp->bitbang.txrx_word[SPI_MODE_1] = s3c2410_spigpio_txrx_mode1; + + /* set state of spi pins */ + s3c2410_gpio_setpin(sp->info->pin_clk, 0); + s3c2410_gpio_setpin(sp->info->pin_mosi, 0); + + s3c2410_gpio_cfgpin(sp->info->pin_clk, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(sp->info->pin_mosi, S3C2410_GPIO_OUTPUT); + s3c2410_gpio_cfgpin(sp->info->pin_miso, S3C2410_GPIO_INPUT); + + ret = spi_bitbang_start(&sp->bitbang); + if (ret) + goto err_no_bitbang; + + /* register the chips to go with the board */ + + for (i = 0; i < sp->info->board_size; i++) { + dev_info(&dev->dev, "registering %p: %s\n", + &sp->info->board_info[i], + sp->info->board_info[i].modalias); + + sp->info->board_info[i].controller_data = sp; + spi_new_device(master, sp->info->board_info + i); + } + + return 0; + + err_no_bitbang: + spi_master_put(sp->bitbang.master); + err: + return ret; + +} + +static int s3c2410_spigpio_remove(struct platform_device *dev) +{ + struct s3c2410_spigpio *sp = platform_get_drvdata(dev); + + spi_bitbang_stop(&sp->bitbang); + spi_master_put(sp->bitbang.master); + + return 0; +} + +/* all gpio should be held over suspend/resume, so we should + * not need to deal with this +*/ + +#define s3c2410_spigpio_suspend NULL +#define s3c2410_spigpio_resume NULL + + +static struct platform_driver s3c2410_spigpio_drv = { + .probe = s3c2410_spigpio_probe, + .remove = s3c2410_spigpio_remove, + .suspend = s3c2410_spigpio_suspend, + .resume = s3c2410_spigpio_resume, + .driver = { + .name = "s3c24xx-spi-gpio", + .owner = THIS_MODULE, + }, +}; + +static int __init s3c2410_spigpio_init(void) +{ + return platform_driver_register(&s3c2410_spigpio_drv); +} + +static void __exit s3c2410_spigpio_exit(void) +{ + platform_driver_unregister(&s3c2410_spigpio_drv); +} + +module_init(s3c2410_spigpio_init); +module_exit(s3c2410_spigpio_exit); + +MODULE_DESCRIPTION("S3C24XX SPI Driver"); +MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>"); +MODULE_LICENSE("GPL"); |