diff options
Diffstat (limited to 'drivers/spi')
| -rw-r--r-- | drivers/spi/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 5 | ||||
| -rw-r--r-- | drivers/spi/amba-pl022.c | 751 | ||||
| -rw-r--r-- | drivers/spi/omap2_mcspi.c | 36 | ||||
| -rw-r--r-- | drivers/spi/orion_spi.c | 4 | ||||
| -rw-r--r-- | drivers/spi/spi_s3c64xx.c | 158 | ||||
| -rw-r--r-- | drivers/spi/spi_topcliff_pch.c | 1303 |
7 files changed, 1963 insertions, 301 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 91c2f4f3af10..d966de1afc52 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -298,6 +298,13 @@ config SPI_STMP3XXX help SPI driver for Freescale STMP37xx/378x SoC SSP interface +config SPI_TOPCLIFF_PCH + tristate "Topcliff PCH SPI Controller" + depends on PCI + help + SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus + used in some x86 embedded processors. + config SPI_TXX9 tristate "Toshiba TXx9 SPI controller" depends on GENERIC_GPIO && CPU_TX49XX diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index e9cbd18217a0..f32d11e1ffec 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -2,9 +2,7 @@ # Makefile for kernel SPI drivers. # -ifeq ($(CONFIG_SPI_DEBUG),y) -EXTRA_CFLAGS += -DDEBUG -endif +ccflags-$(CONFIG_SPI_DEBUG) := -DDEBUG # small core, mostly translating board-specific # config declarations into driver model code @@ -39,6 +37,7 @@ obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o +obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi_topcliff_pch.o obj-$(CONFIG_SPI_TXX9) += spi_txx9.o obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o diff --git a/drivers/spi/amba-pl022.c b/drivers/spi/amba-pl022.c index 4c37c4e28647..fb3d1b31772d 100644 --- a/drivers/spi/amba-pl022.c +++ b/drivers/spi/amba-pl022.c @@ -27,7 +27,6 @@ /* * TODO: * - add timeout on polled transfers - * - add generic DMA framework support */ #include <linux/init.h> @@ -45,6 +44,9 @@ #include <linux/amba/pl022.h> #include <linux/io.h> #include <linux/slab.h> +#include <linux/dmaengine.h> +#include <linux/dma-mapping.h> +#include <linux/scatterlist.h> /* * This macro is used to define some register default values. @@ -381,6 +383,14 @@ struct pl022 { enum ssp_reading read; enum ssp_writing write; u32 exp_fifo_level; + /* DMA settings */ +#ifdef CONFIG_DMA_ENGINE + struct dma_chan *dma_rx_channel; + struct dma_chan *dma_tx_channel; + struct sg_table sgt_rx; + struct sg_table sgt_tx; + char *dummypage; +#endif }; /** @@ -406,7 +416,7 @@ struct chip_data { u16 dmacr; u16 cpsr; u8 n_bytes; - u8 enable_dma:1; + bool enable_dma; enum ssp_reading read; enum ssp_writing write; void (*cs_control) (u32 command); @@ -763,6 +773,371 @@ static void *next_transfer(struct pl022 *pl022) } return STATE_DONE; } + +/* + * This DMA functionality is only compiled in if we have + * access to the generic DMA devices/DMA engine. + */ +#ifdef CONFIG_DMA_ENGINE +static void unmap_free_dma_scatter(struct pl022 *pl022) +{ + /* Unmap and free the SG tables */ + dma_unmap_sg(&pl022->adev->dev, pl022->sgt_tx.sgl, + pl022->sgt_tx.nents, DMA_TO_DEVICE); + dma_unmap_sg(&pl022->adev->dev, pl022->sgt_rx.sgl, + pl022->sgt_rx.nents, DMA_FROM_DEVICE); + sg_free_table(&pl022->sgt_rx); + sg_free_table(&pl022->sgt_tx); +} + +static void dma_callback(void *data) +{ + struct pl022 *pl022 = data; + struct spi_message *msg = pl022->cur_msg; + + BUG_ON(!pl022->sgt_rx.sgl); + +#ifdef VERBOSE_DEBUG + /* + * Optionally dump out buffers to inspect contents, this is + * good if you want to convince yourself that the loopback + * read/write contents are the same, when adopting to a new + * DMA engine. + */ + { + struct scatterlist *sg; + unsigned int i; + + dma_sync_sg_for_cpu(&pl022->adev->dev, + pl022->sgt_rx.sgl, + pl022->sgt_rx.nents, + DMA_FROM_DEVICE); + + for_each_sg(pl022->sgt_rx.sgl, sg, pl022->sgt_rx.nents, i) { + dev_dbg(&pl022->adev->dev, "SPI RX SG ENTRY: %d", i); + print_hex_dump(KERN_ERR, "SPI RX: ", + DUMP_PREFIX_OFFSET, + 16, + 1, + sg_virt(sg), + sg_dma_len(sg), + 1); + } + for_each_sg(pl022->sgt_tx.sgl, sg, pl022->sgt_tx.nents, i) { + dev_dbg(&pl022->adev->dev, "SPI TX SG ENTRY: %d", i); + print_hex_dump(KERN_ERR, "SPI TX: ", + DUMP_PREFIX_OFFSET, + 16, + 1, + sg_virt(sg), + sg_dma_len(sg), + 1); + } + } +#endif + + unmap_free_dma_scatter(pl022); + + /* Update total bytes transfered */ + msg->actual_length += pl022->cur_transfer->len; + if (pl022->cur_transfer->cs_change) + pl022->cur_chip-> + cs_control(SSP_CHIP_DESELECT); + + /* Move to next transfer */ + msg->state = next_transfer(pl022); + tasklet_schedule(&pl022->pump_transfers); +} + +static void setup_dma_scatter(struct pl022 *pl022, + void *buffer, + unsigned int length, + struct sg_table *sgtab) +{ + struct scatterlist *sg; + int bytesleft = length; + void *bufp = buffer; + int mapbytes; + int i; + + if (buffer) { + for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { + /* + * If there are less bytes left than what fits + * in the current page (plus page alignment offset) + * we just feed in this, else we stuff in as much + * as we can. + */ + if (bytesleft < (PAGE_SIZE - offset_in_page(bufp))) + mapbytes = bytesleft; + else + mapbytes = PAGE_SIZE - offset_in_page(bufp); + sg_set_page(sg, virt_to_page(bufp), + mapbytes, offset_in_page(bufp)); + bufp += mapbytes; + bytesleft -= mapbytes; + dev_dbg(&pl022->adev->dev, + "set RX/TX target page @ %p, %d bytes, %d left\n", + bufp, mapbytes, bytesleft); + } + } else { + /* Map the dummy buffer on every page */ + for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { + if (bytesleft < PAGE_SIZE) + mapbytes = bytesleft; + else + mapbytes = PAGE_SIZE; + sg_set_page(sg, virt_to_page(pl022->dummypage), + mapbytes, 0); + bytesleft -= mapbytes; + dev_dbg(&pl022->adev->dev, + "set RX/TX to dummy page %d bytes, %d left\n", + mapbytes, bytesleft); + + } + } + BUG_ON(bytesleft); +} + +/** + * configure_dma - configures the channels for the next transfer + * @pl022: SSP driver's private data structure + */ +static int configure_dma(struct pl022 *pl022) +{ + struct dma_slave_config rx_conf = { + .src_addr = SSP_DR(pl022->phybase), + .direction = DMA_FROM_DEVICE, + .src_maxburst = pl022->vendor->fifodepth >> 1, + }; + struct dma_slave_config tx_conf = { + .dst_addr = SSP_DR(pl022->phybase), + .direction = DMA_TO_DEVICE, + .dst_maxburst = pl022->vendor->fifodepth >> 1, + }; + unsigned int pages; + int ret; + int sglen; + struct dma_chan *rxchan = pl022->dma_rx_channel; + struct dma_chan *txchan = pl022->dma_tx_channel; + struct dma_async_tx_descriptor *rxdesc; + struct dma_async_tx_descriptor *txdesc; + dma_cookie_t cookie; + + /* Check that the channels are available */ + if (!rxchan || !txchan) + return -ENODEV; + + switch (pl022->read) { + case READING_NULL: + /* Use the same as for writing */ + rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; + break; + case READING_U8: + rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + break; + case READING_U16: + rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; + break; + case READING_U32: + rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + break; + } + + switch (pl022->write) { + case WRITING_NULL: + /* Use the same as for reading */ + tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; + break; + case WRITING_U8: + tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; + break; + case WRITING_U16: + tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; + break; + case WRITING_U32: + tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;; + break; + } + + /* SPI pecularity: we need to read and write the same width */ + if (rx_conf.src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) + rx_conf.src_addr_width = tx_conf.dst_addr_width; + if (tx_conf.dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) + tx_conf.dst_addr_width = rx_conf.src_addr_width; + BUG_ON(rx_conf.src_addr_width != tx_conf.dst_addr_width); + + rxchan->device->device_control(rxchan, DMA_SLAVE_CONFIG, + (unsigned long) &rx_conf); + txchan->device->device_control(txchan, DMA_SLAVE_CONFIG, + (unsigned long) &tx_conf); + + /* Create sglists for the transfers */ + pages = (pl022->cur_transfer->len >> PAGE_SHIFT) + 1; + dev_dbg(&pl022->adev->dev, "using %d pages for transfer\n", pages); + + ret = sg_alloc_table(&pl022->sgt_rx, pages, GFP_KERNEL); + if (ret) + goto err_alloc_rx_sg; + + ret = sg_alloc_table(&pl022->sgt_tx, pages, GFP_KERNEL); + if (ret) + goto err_alloc_tx_sg; + + /* Fill in the scatterlists for the RX+TX buffers */ + setup_dma_scatter(pl022, pl022->rx, + pl022->cur_transfer->len, &pl022->sgt_rx); + setup_dma_scatter(pl022, pl022->tx, + pl022->cur_transfer->len, &pl022->sgt_tx); + + /* Map DMA buffers */ + sglen = dma_map_sg(&pl022->adev->dev, pl022->sgt_rx.sgl, + pl022->sgt_rx.nents, DMA_FROM_DEVICE); + if (!sglen) + goto err_rx_sgmap; + + sglen = dma_map_sg(&pl022->adev->dev, pl022->sgt_tx.sgl, + pl022->sgt_tx.nents, DMA_TO_DEVICE); + if (!sglen) + goto err_tx_sgmap; + + /* Send both scatterlists */ + rxdesc = rxchan->device->device_prep_slave_sg(rxchan, + pl022->sgt_rx.sgl, + pl022->sgt_rx.nents, + DMA_FROM_DEVICE, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!rxdesc) + goto err_rxdesc; + + txdesc = txchan->device->device_prep_slave_sg(txchan, + pl022->sgt_tx.sgl, + pl022->sgt_tx.nents, + DMA_TO_DEVICE, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + if (!txdesc) + goto err_txdesc; + + /* Put the callback on the RX transfer only, that should finish last */ + rxdesc->callback = dma_callback; + rxdesc->callback_param = pl022; + + /* Submit and fire RX and TX with TX last so we're ready to read! */ + cookie = rxdesc->tx_submit(rxdesc); + if (dma_submit_error(cookie)) + goto err_submit_rx; + cookie = txdesc->tx_submit(txdesc); + if (dma_submit_error(cookie)) + goto err_submit_tx; + rxchan->device->device_issue_pending(rxchan); + txchan->device->device_issue_pending(txchan); + + return 0; + +err_submit_tx: +err_submit_rx: +err_txdesc: + txchan->device->device_control(txchan, DMA_TERMINATE_ALL, 0); +err_rxdesc: + rxchan->device->device_control(rxchan, DMA_TERMINATE_ALL, 0); + dma_unmap_sg(&pl022->adev->dev, pl022->sgt_tx.sgl, + pl022->sgt_tx.nents, DMA_TO_DEVICE); +err_tx_sgmap: + dma_unmap_sg(&pl022->adev->dev, pl022->sgt_rx.sgl, + pl022->sgt_tx.nents, DMA_FROM_DEVICE); +err_rx_sgmap: + sg_free_table(&pl022->sgt_tx); +err_alloc_tx_sg: + sg_free_table(&pl022->sgt_rx); +err_alloc_rx_sg: + return -ENOMEM; +} + +static int __init pl022_dma_probe(struct pl022 *pl022) +{ + dma_cap_mask_t mask; + + /* Try to acquire a generic DMA engine slave channel */ + dma_cap_zero(mask); + dma_cap_set(DMA_SLAVE, mask); + /* + * We need both RX and TX channels to do DMA, else do none + * of them. + */ + pl022->dma_rx_channel = dma_request_channel(mask, + pl022->master_info->dma_filter, + pl022->master_info->dma_rx_param); + if (!pl022->dma_rx_channel) { + dev_err(&pl022->adev->dev, "no RX DMA channel!\n"); + goto err_no_rxchan; + } + + pl022->dma_tx_channel = dma_request_channel(mask, + pl022->master_info->dma_filter, + pl022->master_info->dma_tx_param); + if (!pl022->dma_tx_channel) { + dev_err(&pl022->adev->dev, "no TX DMA channel!\n"); + goto err_no_txchan; + } + + pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); + if (!pl022->dummypage) { + dev_err(&pl022->adev->dev, "no DMA dummypage!\n"); + goto err_no_dummypage; + } + + dev_info(&pl022->adev->dev, "setup for DMA on RX %s, TX %s\n", + dma_chan_name(pl022->dma_rx_channel), + dma_chan_name(pl022->dma_tx_channel)); + + return 0; + +err_no_dummypage: + dma_release_channel(pl022->dma_tx_channel); +err_no_txchan: + dma_release_channel(pl022->dma_rx_channel); + pl022->dma_rx_channel = NULL; +err_no_rxchan: + return -ENODEV; +} + +static void terminate_dma(struct pl022 *pl022) +{ + struct dma_chan *rxchan = pl022->dma_rx_channel; + struct dma_chan *txchan = pl022->dma_tx_channel; + + rxchan->device->device_control(rxchan, DMA_TERMINATE_ALL, 0); + txchan->device->device_control(txchan, DMA_TERMINATE_ALL, 0); + unmap_free_dma_scatter(pl022); +} + +static void pl022_dma_remove(struct pl022 *pl022) +{ + if (pl022->busy) + terminate_dma(pl022); + if (pl022->dma_tx_channel) + dma_release_channel(pl022->dma_tx_channel); + if (pl022->dma_rx_channel) + dma_release_channel(pl022->dma_rx_channel); + kfree(pl022->dummypage); +} + +#else +static inline int configure_dma(struct pl022 *pl022) +{ + return -ENODEV; +} + +static inline int pl022_dma_probe(struct pl022 *pl022) +{ + return 0; +} + +static inline void pl022_dma_remove(struct pl022 *pl022) +{ +} +#endif + /** * pl022_interrupt_handler - Interrupt handler for SSP controller * @@ -794,14 +1169,17 @@ static irqreturn_t pl022_interrupt_handler(int irq, void *dev_id) if (unlikely(!irq_status)) return IRQ_NONE; - /* This handles the error code interrupts */ + /* + * This handles the FIFO interrupts, the timeout + * interrupts are flatly ignored, they cannot be + * trusted. + */ if (unlikely(irq_status & SSP_MIS_MASK_RORMIS)) { /* * Overrun interrupt - bail out since our Data has been * corrupted */ - dev_err(&pl022->adev->dev, - "FIFO overrun\n"); + dev_err(&pl022->adev->dev, "FIFO overrun\n"); if (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RFF) dev_err(&pl022->adev->dev, "RXFIFO is full\n"); @@ -896,8 +1274,8 @@ static int set_up_next_transfer(struct pl022 *pl022, } /** - * pump_transfers - Tasklet function which schedules next interrupt transfer - * when running in interrupt transfer mode. + * pump_transfers - Tasklet function which schedules next transfer + * when running in interrupt or DMA transfer mode. * @data: SSP driver private data structure * */ @@ -954,65 +1332,23 @@ static void pump_transfers(unsigned long data) } /* Flush the FIFOs and let's go! */ flush(pl022); - writew(ENABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); -} - -/** - * NOT IMPLEMENTED - * configure_dma - It configures the DMA pipes for DMA transfers - * @data: SSP driver's private data structure - * - */ -static int configure_dma(void *data) -{ - struct pl022 *pl022 = data; - dev_dbg(&pl022->adev->dev, "configure DMA\n"); - return -ENOTSUPP; -} - -/** - * do_dma_transfer - It handles transfers of the current message - * if it is DMA xfer. - * NOT FULLY IMPLEMENTED - * @data: SSP driver's private data structure - */ -static void do_dma_transfer(void *data) -{ - struct pl022 *pl022 = data; - - if (configure_dma(data)) { - dev_dbg(&pl022->adev->dev, "configuration of DMA Failed!\n"); - goto err_config_dma; - } - /* TODO: Implememt DMA setup of pipes here */ - - /* Enable target chip, set up transfer */ - pl022->cur_chip->cs_control(SSP_CHIP_SELECT); - if (set_up_next_transfer(pl022, pl022->cur_transfer)) { - /* Error path */ - pl022->cur_msg->state = STATE_ERROR; - pl022->cur_msg->status = -EIO; - giveback(pl022); + if (pl022->cur_chip->enable_dma) { + if (configure_dma(pl022)) { + dev_dbg(&pl022->adev->dev, + "configuration of DMA failed, fall back to interrupt mode\n"); + goto err_config_dma; + } return; } - /* Enable SSP */ - writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), - SSP_CR1(pl022->virtbase)); - - /* TODO: Enable the DMA transfer here */ - return; - err_config_dma: - pl022->cur_msg->state = STATE_ERROR; - pl022->cur_msg->status = -EIO; - giveback(pl022); - return; +err_config_dma: + writew(ENABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); } -static void do_interrupt_transfer(void *data) +static void do_interrupt_dma_transfer(struct pl022 *pl022) { - struct pl022 *pl022 = data; + u32 irqflags = ENABLE_ALL_INTERRUPTS; /* Enable target chip */ pl022->cur_chip->cs_control(SSP_CHIP_SELECT); @@ -1023,15 +1359,26 @@ static void do_interrupt_transfer(void *data) giveback(pl022); return; } + /* If we're using DMA, set up DMA here */ + if (pl022->cur_chip->enable_dma) { + /* Configure DMA transfer */ + if (configure_dma(pl022)) { + dev_dbg(&pl022->adev->dev, + "configuration of DMA failed, fall back to interrupt mode\n"); + goto err_config_dma; + } + /* Disable interrupts in DMA mode, IRQ from DMA controller */ + irqflags = DISABLE_ALL_INTERRUPTS; + } +err_config_dma: /* Enable SSP, turn on interrupts */ writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), SSP_CR1(pl022->virtbase)); - writew(ENABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); + writew(irqflags, SSP_IMSC(pl022->virtbase)); } -static void do_polling_transfer(void *data) +static void do_polling_transfer(struct pl022 *pl022) { - struct pl022 *pl022 = data; struct spi_message *message = NULL; struct spi_transfer *transfer = NULL; struct spi_transfer *previous = NULL; @@ -1101,7 +1448,7 @@ static void do_polling_transfer(void *data) * * This function checks if there is any spi message in the queue that * needs processing and delegate control to appropriate function - * do_polling_transfer()/do_interrupt_transfer()/do_dma_transfer() + * do_polling_transfer()/do_interrupt_dma_transfer() * based on the kind of the transfer * */ @@ -1150,10 +1497,8 @@ static void pump_messages(struct work_struct *work) if (pl022->cur_chip->xfer_type == POLLING_TRANSFER) do_polling_transfer(pl022); - else if (pl022->cur_chip->xfer_type == INTERRUPT_TRANSFER) - do_interrupt_transfer(pl022); else - do_dma_transfer(pl022); + do_interrupt_dma_transfer(pl022); } @@ -1248,100 +1593,56 @@ static int destroy_queue(struct pl022 *pl022) } static int verify_controller_parameters(struct pl022 *pl022, - struct pl022_config_chip *chip_info) + struct pl022_config_chip const *chip_info) { - if ((chip_info->lbm != LOOPBACK_ENABLED) - && (chip_info->lbm != LOOPBACK_DISABLED)) { - dev_err(chip_info->dev, - "loopback Mode is configured incorrectly\n"); - return -EINVAL; - } if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI) || (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "interface is configured incorrectly\n"); return -EINVAL; } if ((chip_info->iface == SSP_INTERFACE_UNIDIRECTIONAL) && (!pl022->vendor->unidir)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "unidirectional mode not supported in this " "hardware version\n"); return -EINVAL; } if ((chip_info->hierarchy != SSP_MASTER) && (chip_info->hierarchy != SSP_SLAVE)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "hierarchy is configured incorrectly\n"); return -EINVAL; } - if (((chip_info->clk_freq).cpsdvsr < CPSDVR_MIN) - || ((chip_info->clk_freq).cpsdvsr > CPSDVR_MAX)) { - dev_err(chip_info->dev, - "cpsdvsr is configured incorrectly\n"); - return -EINVAL; - } - if ((chip_info->endian_rx != SSP_RX_MSB) - && (chip_info->endian_rx != SSP_RX_LSB)) { - dev_err(chip_info->dev, - "RX FIFO endianess is configured incorrectly\n"); - return -EINVAL; - } - if ((chip_info->endian_tx != SSP_TX_MSB) - && (chip_info->endian_tx != SSP_TX_LSB)) { - dev_err(chip_info->dev, - "TX FIFO endianess is configured incorrectly\n"); - return -EINVAL; - } - if ((chip_info->data_size < SSP_DATA_BITS_4) - || (chip_info->data_size > SSP_DATA_BITS_32)) { - dev_err(chip_info->dev, - "DATA Size is configured incorrectly\n"); - return -EINVAL; - } if ((chip_info->com_mode != INTERRUPT_TRANSFER) && (chip_info->com_mode != DMA_TRANSFER) && (chip_info->com_mode != POLLING_TRANSFER)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "Communication mode is configured incorrectly\n"); return -EINVAL; } if ((chip_info->rx_lev_trig < SSP_RX_1_OR_MORE_ELEM) || (chip_info->rx_lev_trig > SSP_RX_32_OR_MORE_ELEM)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "RX FIFO Trigger Level is configured incorrectly\n"); return -EINVAL; } if ((chip_info->tx_lev_trig < SSP_TX_1_OR_MORE_EMPTY_LOC) || (chip_info->tx_lev_trig > SSP_TX_32_OR_MORE_EMPTY_LOC)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "TX FIFO Trigger Level is configured incorrectly\n"); return -EINVAL; } - if (chip_info->iface == SSP_INTERFACE_MOTOROLA_SPI) { - if ((chip_info->clk_phase != SSP_CLK_FIRST_EDGE) - && (chip_info->clk_phase != SSP_CLK_SECOND_EDGE)) { - dev_err(chip_info->dev, - "Clock Phase is configured incorrectly\n"); - return -EINVAL; - } - if ((chip_info->clk_pol != SSP_CLK_POL_IDLE_LOW) - && (chip_info->clk_pol != SSP_CLK_POL_IDLE_HIGH)) { - dev_err(chip_info->dev, - "Clock Polarity is configured incorrectly\n"); - return -EINVAL; - } - } if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) { if ((chip_info->ctrl_len < SSP_BITS_4) || (chip_info->ctrl_len > SSP_BITS_32)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "CTRL LEN is configured incorrectly\n"); return -EINVAL; } if ((chip_info->wait_state != SSP_MWIRE_WAIT_ZERO) && (chip_info->wait_state != SSP_MWIRE_WAIT_ONE)) { - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "Wait State is configured incorrectly\n"); return -EINVAL; } @@ -1350,24 +1651,20 @@ static int verify_controller_parameters(struct pl022 *pl022, if ((chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) && (chip_info->duplex != - SSP_MICROWIRE_CHANNEL_HALF_DUPLEX)) - dev_err(chip_info->dev, + SSP_MICROWIRE_CHANNEL_HALF_DUPLEX)) { + dev_err(&pl022->adev->dev, "Microwire duplex mode is configured incorrectly\n"); return -EINVAL; + } } else { if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) - dev_err(chip_info->dev, + dev_err(&pl022->adev->dev, "Microwire half duplex mode requested," " but this is only available in the" " ST version of PL022\n"); return -EINVAL; } } - if (chip_info->cs_control == NULL) { - dev_warn(chip_info->dev, - "Chip Select Function is NULL for this chip\n"); - chip_info->cs_control = null_cs_control; - } return 0; } @@ -1467,22 +1764,24 @@ static int calculate_effective_freq(struct pl022 *pl022, return 0; } -/** - * NOT IMPLEMENTED - * process_dma_info - Processes the DMA info provided by client drivers - * @chip_info: chip info provided by client device - * @chip: Runtime state maintained by the SSP controller for each spi device - * - * This function processes and stores DMA config provided by client driver - * into the runtime state maintained by the SSP controller driver + +/* + * A piece of default chip info unless the platform + * supplies it. */ -static int process_dma_info(struct pl022_config_chip *chip_info, - struct chip_data *chip) -{ - dev_err(chip_info->dev, - "cannot process DMA info, DMA not implemented!\n"); - return -ENOTSUPP; -} +static const struct pl022_config_chip pl022_default_chip_info = { + .com_mode = POLLING_TRANSFER, + .iface = SSP_INTERFACE_MOTOROLA_SPI, + .hierarchy = SSP_SLAVE, + .slave_tx_disable = DO_NOT_DRIVE_TX, + .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, + .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC, + .ctrl_len = SSP_BITS_8, + .wait_state = SSP_MWIRE_WAIT_ZERO, + .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, + .cs_control = null_cs_control, +}; + /** * pl022_setup - setup function registered to SPI master framework @@ -1496,23 +1795,15 @@ static int process_dma_info(struct pl022_config_chip *chip_info, * controller hardware here, that is not done until the actual transfer * commence. */ - -/* FIXME: JUST GUESSING the spi->mode bits understood by this driver */ -#define MODEBITS (SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \ - | SPI_LSB_FIRST | SPI_LOOP) - static int pl022_setup(struct spi_device *spi) { - struct pl022_config_chip *chip_info; + struct pl022_config_chip const *chip_info; struct chip_data *chip; + struct ssp_clock_params clk_freq; int status = 0; struct pl022 *pl022 = spi_master_get_devdata(spi->master); - - if (spi->mode & ~MODEBITS) { - dev_dbg(&spi->dev, "unsupported mode bits %x\n", - spi->mode & ~MODEBITS); - return -EINVAL; - } + unsigned int bits = spi->bits_per_word; + u32 tmp; if (!spi->max_speed_hz) return -EINVAL; @@ -1535,48 +1826,13 @@ static int pl022_setup(struct spi_device *spi) chip_info = spi->controller_data; if (chip_info == NULL) { + chip_info = &pl022_default_chip_info; /* spi_board_info.controller_data not is supplied */ dev_dbg(&spi->dev, "using default controller_data settings\n"); - - chip_info = - kzalloc(sizeof(struct pl022_config_chip), GFP_KERNEL); - - if (!chip_info) { - dev_err(&spi->dev, - "cannot allocate controller data\n"); - status = -ENOMEM; - goto err_first_setup; - } - - dev_dbg(&spi->dev, "allocated memory for controller data\n"); - - /* Pointer back to the SPI device */ - chip_info->dev = &spi->dev; - /* - * Set controller data default values: - * Polling is supported by default - */ - chip_info->lbm = LOOPBACK_DISABLED; - chip_info->com_mode = POLLING_TRANSFER; - chip_info->iface = SSP_INTERFACE_MOTOROLA_SPI; - chip_info->hierarchy = SSP_SLAVE; - chip_info->slave_tx_disable = DO_NOT_DRIVE_TX; - chip_info->endian_tx = SSP_TX_LSB; - chip_info->endian_rx = SSP_RX_LSB; - chip_info->data_size = SSP_DATA_BITS_12; - chip_info->rx_lev_trig = SSP_RX_1_OR_MORE_ELEM; - chip_info->tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC; - chip_info->clk_phase = SSP_CLK_SECOND_EDGE; - chip_info->clk_pol = SSP_CLK_POL_IDLE_LOW; - chip_info->ctrl_len = SSP_BITS_8; - chip_info->wait_state = SSP_MWIRE_WAIT_ZERO; - chip_info->duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX; - chip_info->cs_control = null_cs_control; - } else { + } else dev_dbg(&spi->dev, "using user supplied controller_data settings\n"); - } /* * We can override with custom divisors, else we use the board @@ -1586,29 +1842,48 @@ static int pl022_setup(struct spi_device *spi) && (0 == chip_info->clk_freq.scr)) { status = calculate_effective_freq(pl022, spi->max_speed_hz, - &chip_info->clk_freq); + &clk_freq); if (status < 0) goto err_config_params; } else { - if ((chip_info->clk_freq.cpsdvsr % 2) != 0) - chip_info->clk_freq.cpsdvsr = - chip_info->clk_freq.cpsdvsr - 1; + memcpy(&clk_freq, &chip_info->clk_freq, sizeof(clk_freq)); + if ((clk_freq.cpsdvsr % 2) != 0) + clk_freq.cpsdvsr = + clk_freq.cpsdvsr - 1; + } + if ((clk_freq.cpsdvsr < CPSDVR_MIN) + || (clk_freq.cpsdvsr > CPSDVR_MAX)) { + dev_err(&spi->dev, + "cpsdvsr is configured incorrectly\n"); + goto err_config_params; } + + status = verify_controller_parameters(pl022, chip_info); if (status) { dev_err(&spi->dev, "controller data is incorrect"); goto err_config_params; } + /* Now set controller state based on controller data */ chip->xfer_type = chip_info->com_mode; - chip->cs_control = chip_info->cs_control; - - if (chip_info->data_size <= 8) { - dev_dbg(&spi->dev, "1 <= n <=8 bits per word\n"); + if (!chip_info->cs_control) { + chip->cs_control = null_cs_control; + dev_warn(&spi->dev, + "chip select function is NULL for this chip\n"); + } else + chip->cs_control = chip_info->cs_control; + + if (bits <= 3) { + /* PL022 doesn't support less than 4-bits */ + status = -ENOTSUPP; + goto err_config_params; + } else if (bits <= 8) { + dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n"); chip->n_bytes = 1; chip->read = READING_U8; chip->write = WRITING_U8; - } else if (chip_info->data_size <= 16) { + } else if (bits <= 16) { dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n"); chip->n_bytes = 2; chip->read = READING_U16; @@ -1625,6 +1900,7 @@ static int pl022_setup(struct spi_device *spi) dev_err(&spi->dev, "a standard pl022 can only handle " "1 <= n <= 16 bit words\n"); + status = -ENOTSUPP; goto err_config_params; } } @@ -1636,9 +1912,8 @@ static int pl022_setup(struct spi_device *spi) chip->cpsr = 0; if ((chip_info->com_mode == DMA_TRANSFER) && ((pl022->master_info)->enable_dma)) { - chip->enable_dma = 1; + chip->enable_dma = true; dev_dbg(&spi->dev, "DMA mode set in controller state\n"); - status = process_dma_info(chip_info, chip); if (status < 0) goto err_config_params; SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, @@ -1646,7 +1921,7 @@ static int pl022_setup(struct spi_device *spi) SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, SSP_DMACR_MASK_TXDMAE, 1); } else { - chip->enable_dma = 0; + chip->enable_dma = false; dev_dbg(&spi->dev, "DMA mode NOT set in controller state\n"); SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, SSP_DMACR_MASK_RXDMAE, 0); @@ -1654,10 +1929,12 @@ static int pl022_setup(struct spi_device *spi) SSP_DMACR_MASK_TXDMAE, 1); } - chip->cpsr = chip_info->clk_freq.cpsdvsr; + chip->cpsr = clk_freq.cpsdvsr; /* Special setup for the ST micro extended control registers */ if (pl022->vendor->extended_cr) { + u32 etx; + if (pl022->vendor->pl023) { /* These bits are only in the PL023 */ SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay, @@ -1673,29 +1950,51 @@ static int pl022_setup(struct spi_device *spi) SSP_WRITE_BITS(chip->cr1, chip_info->wait_state, SSP_CR1_MASK_MWAIT_ST, 6); } - SSP_WRITE_BITS(chip->cr0, chip_info->data_size, + SSP_WRITE_BITS(chip->cr0, bits - 1, SSP_CR0_MASK_DSS_ST, 0); - SSP_WRITE_BITS(chip->cr1, chip_info->endian_rx, - SSP_CR1_MASK_RENDN_ST, 4); - SSP_WRITE_BITS(chip->cr1, chip_info->endian_tx, - SSP_CR1_MASK_TENDN_ST, 5); + + if (spi->mode & SPI_LSB_FIRST) { + tmp = SSP_RX_LSB; + etx = SSP_TX_LSB; + } else { + tmp = SSP_RX_MSB; + etx = SSP_TX_MSB; + } + SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4); + SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5); SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig, SSP_CR1_MASK_RXIFLSEL_ST, 7); SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig, SSP_CR1_MASK_TXIFLSEL_ST, 10); } else { - SSP_WRITE_BITS(chip->cr0, chip_info->data_size, + SSP_WRITE_BITS(chip->cr0, bits - 1, SSP_CR0_MASK_DSS, 0); SSP_WRITE_BITS(chip->cr0, chip_info->iface, SSP_CR0_MASK_FRF, 4); } + /* Stuff that is common for all versions */ - SSP_WRITE_BITS(chip->cr0, chip_info->clk_pol, SSP_CR0_MASK_SPO, 6); - SSP_WRITE_BITS(chip->cr0, chip_info->clk_phase, SSP_CR0_MASK_SPH, 7); - SSP_WRITE_BITS(chip->cr0, chip_info->clk_freq.scr, SSP_CR0_MASK_SCR, 8); + if (spi->mode & SPI_CPOL) + tmp = SSP_CLK_POL_IDLE_HIGH; + else + tmp = SSP_CLK_POL_IDLE_LOW; + SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6); + + if (spi->mode & SPI_CPHA) + tmp = SSP_CLK_SECOND_EDGE; + else + tmp = SSP_CLK_FIRST_EDGE; + SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 7); + + SSP_WRITE_BITS(chip->cr0, clk_freq.scr, SSP_CR0_MASK_SCR, 8); /* Loopback is available on all versions except PL023 */ - if (!pl022->vendor->pl023) - SSP_WRITE_BITS(chip->cr1, chip_info->lbm, SSP_CR1_MASK_LBM, 0); + if (!pl022->vendor->pl023) { + if (spi->mode & SPI_LOOP) + tmp = LOOPBACK_ENABLED; + else + tmp = LOOPBACK_DISABLED; + SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0); + } SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1); SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2); SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 3); @@ -1704,7 +2003,7 @@ static int pl022_setup(struct spi_device *spi) spi_set_ctldata(spi, chip); return status; err_config_params: - err_first_setup: + spi_set_ctldata(spi, NULL); kfree(chip); return status; } @@ -1766,12 +2065,21 @@ pl022_probe(struct amba_device *adev, struct amba_id *id) master->setup = pl022_setup; master->transfer = pl022_transfer; + /* + * Supports mode 0-3, loopback, and active low CS. Transfers are + * always MS bit first on the original pl022. + */ + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP; + if (pl022->vendor->extended_cr) + master->mode_bits |= SPI_LSB_FIRST; + dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num); status = amba_request_regions(adev, NULL); if (status) goto err_no_ioregion; + pl022->phybase = adev->res.start; pl022->virtbase = ioremap(adev->res.start, resource_size(&adev->res)); if (pl022->virtbase == NULL) { status = -ENOMEM; @@ -1798,6 +2106,14 @@ pl022_probe(struct amba_device *adev, struct amba_id *id) dev_err(&adev->dev, "probe - cannot get IRQ (%d)\n", status); goto err_no_irq; } + + /* Get DMA channels */ + if (platform_info->enable_dma) { + status = pl022_dma_probe(pl022); + if (status != 0) + goto err_no_dma; + } + /* Initialize and start queue */ status = init_queue(pl022); if (status != 0) { @@ -1826,6 +2142,8 @@ pl022_probe(struct amba_device *adev, struct amba_id *id) err_start_queue: err_init_queue: destroy_queue(pl022); + pl022_dma_remove(pl022); + err_no_dma: free_irq(adev->irq[0], pl022); err_no_irq: clk_put(pl022->clk); @@ -1856,6 +2174,7 @@ pl022_remove(struct amba_device *adev) return status; } load_ssp_default_config(pl022); + pl022_dma_remove(pl022); free_irq(adev->irq[0], pl022); clk_disable(pl022->clk); clk_put(pl022->clk); diff --git a/drivers/spi/omap2_mcspi.c b/drivers/spi/omap2_mcspi.c index b3a94ca0a75a..d70392795055 100644 --- a/drivers/spi/omap2_mcspi.c +++ b/drivers/spi/omap2_mcspi.c @@ -489,10 +489,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) dev_err(&spi->dev, "TXS timed out\n"); goto out; } -#ifdef VERBOSE - dev_dbg(&spi->dev, "write-%d %02x\n", + dev_vdbg(&spi->dev, "write-%d %02x\n", word_len, *tx); -#endif __raw_writel(*tx++, tx_reg); } if (rx != NULL) { @@ -506,10 +504,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) (l & OMAP2_MCSPI_CHCONF_TURBO)) { omap2_mcspi_set_enable(spi, 0); *rx++ = __raw_readl(rx_reg); -#ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %02x\n", + dev_vdbg(&spi->dev, "read-%d %02x\n", word_len, *(rx - 1)); -#endif if (mcspi_wait_for_reg_bit(chstat_reg, OMAP2_MCSPI_CHSTAT_RXS) < 0) { dev_err(&spi->dev, @@ -522,10 +518,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) } *rx++ = __raw_readl(rx_reg); -#ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %02x\n", + dev_vdbg(&spi->dev, "read-%d %02x\n", word_len, *(rx - 1)); -#endif } } while (c); } else if (word_len <= 16) { @@ -542,10 +536,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) dev_err(&spi->dev, "TXS timed out\n"); goto out; } -#ifdef VERBOSE - dev_dbg(&spi->dev, "write-%d %04x\n", + dev_vdbg(&spi->dev, "write-%d %04x\n", word_len, *tx); -#endif __raw_writel(*tx++, tx_reg); } if (rx != NULL) { @@ -559,10 +551,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) (l & OMAP2_MCSPI_CHCONF_TURBO)) { omap2_mcspi_set_enable(spi, 0); *rx++ = __raw_readl(rx_reg); -#ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %04x\n", + dev_vdbg(&spi->dev, "read-%d %04x\n", word_len, *(rx - 1)); -#endif if (mcspi_wait_for_reg_bit(chstat_reg, OMAP2_MCSPI_CHSTAT_RXS) < 0) { dev_err(&spi->dev, @@ -575,10 +565,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) } *rx++ = __raw_readl(rx_reg); -#ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %04x\n", + dev_vdbg(&spi->dev, "read-%d %04x\n", word_len, *(rx - 1)); -#endif } } while (c); } else if (word_len <= 32) { @@ -595,10 +583,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) dev_err(&spi->dev, "TXS timed out\n"); goto out; } -#ifdef VERBOSE - dev_dbg(&spi->dev, "write-%d %08x\n", + dev_vdbg(&spi->dev, "write-%d %08x\n", word_len, *tx); -#endif __raw_writel(*tx++, tx_reg); } if (rx != NULL) { @@ -612,10 +598,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) (l & OMAP2_MCSPI_CHCONF_TURBO)) { omap2_mcspi_set_enable(spi, 0); *rx++ = __raw_readl(rx_reg); -#ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %08x\n", + dev_vdbg(&spi->dev, "read-%d %08x\n", word_len, *(rx - 1)); -#endif if (mcspi_wait_for_reg_bit(chstat_reg, OMAP2_MCSPI_CHSTAT_RXS) < 0) { dev_err(&spi->dev, @@ -628,10 +612,8 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer) } *rx++ = __raw_readl(rx_reg); -#ifdef VERBOSE - dev_dbg(&spi->dev, "read-%d %08x\n", + dev_vdbg(&spi->dev, "read-%d %08x\n", word_len, *(rx - 1)); -#endif } } while (c); } diff --git a/drivers/spi/orion_spi.c b/drivers/spi/orion_spi.c index 3aea50da7b29..0b677dc041ad 100644 --- a/drivers/spi/orion_spi.c +++ b/drivers/spi/orion_spi.c @@ -404,7 +404,7 @@ static int orion_spi_transfer(struct spi_device *spi, struct spi_message *m) goto msg_rejected; } - if ((t != NULL) && t->bits_per_word) + if (t->bits_per_word) bits_per_word = t->bits_per_word; if ((bits_per_word != 8) && (bits_per_word != 16)) { @@ -415,7 +415,7 @@ static int orion_spi_transfer(struct spi_device *spi, struct spi_message *m) goto msg_rejected; } /*make sure buffer length is even when working in 16 bit mode*/ - if ((t != NULL) && (t->bits_per_word == 16) && (t->len & 1)) { + if ((t->bits_per_word == 16) && (t->len & 1)) { dev_err(&spi->dev, "message rejected : " "odd data length (%d) while in 16 bit mode\n", diff --git a/drivers/spi/spi_s3c64xx.c b/drivers/spi/spi_s3c64xx.c index c3038da2648a..795828b90f45 100644 --- a/drivers/spi/spi_s3c64xx.c +++ b/drivers/spi/spi_s3c64xx.c @@ -261,15 +261,25 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd, chcfg |= S3C64XX_SPI_CH_TXCH_ON; if (dma_mode) { modecfg |= S3C64XX_SPI_MODE_TXDMA_ON; - s3c2410_dma_config(sdd->tx_dmach, 1); + s3c2410_dma_config(sdd->tx_dmach, sdd->cur_bpw / 8); s3c2410_dma_enqueue(sdd->tx_dmach, (void *)sdd, xfer->tx_dma, xfer->len); s3c2410_dma_ctrl(sdd->tx_dmach, S3C2410_DMAOP_START); } else { - unsigned char *buf = (unsigned char *) xfer->tx_buf; - int i = 0; - while (i < xfer->len) - writeb(buf[i++], regs + S3C64XX_SPI_TX_DATA); + switch (sdd->cur_bpw) { + case 32: + iowrite32_rep(regs + S3C64XX_SPI_TX_DATA, + xfer->tx_buf, xfer->len / 4); + break; + case 16: + iowrite16_rep(regs + S3C64XX_SPI_TX_DATA, + xfer->tx_buf, xfer->len / 2); + break; + default: + iowrite8_rep(regs + S3C64XX_SPI_TX_DATA, + xfer->tx_buf, xfer->len); + break; + } } } @@ -286,7 +296,7 @@ static void enable_datapath(struct s3c64xx_spi_driver_data *sdd, writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff) | S3C64XX_SPI_PACKET_CNT_EN, regs + S3C64XX_SPI_PACKET_CNT); - s3c2410_dma_config(sdd->rx_dmach, 1); + s3c2410_dma_config(sdd->rx_dmach, sdd->cur_bpw / 8); s3c2410_dma_enqueue(sdd->rx_dmach, (void *)sdd, xfer->rx_dma, xfer->len); s3c2410_dma_ctrl(sdd->rx_dmach, S3C2410_DMAOP_START); @@ -366,20 +376,26 @@ static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd, return -EIO; } } else { - unsigned char *buf; - int i; - /* If it was only Tx */ if (xfer->rx_buf == NULL) { sdd->state &= ~TXBUSY; return 0; } - i = 0; - buf = xfer->rx_buf; - while (i < xfer->len) - buf[i++] = readb(regs + S3C64XX_SPI_RX_DATA); - + switch (sdd->cur_bpw) { + case 32: + ioread32_rep(regs + S3C64XX_SPI_RX_DATA, + xfer->rx_buf, xfer->len / 4); + break; + case 16: + ioread16_rep(regs + S3C64XX_SPI_RX_DATA, + xfer->rx_buf, xfer->len / 2); + break; + default: + ioread8_rep(regs + S3C64XX_SPI_RX_DATA, + xfer->rx_buf, xfer->len); + break; + } sdd->state &= ~RXBUSY; } @@ -399,13 +415,18 @@ static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd, static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) { + struct s3c64xx_spi_info *sci = sdd->cntrlr_info; void __iomem *regs = sdd->regs; u32 val; /* Disable Clock */ - val = readl(regs + S3C64XX_SPI_CLK_CFG); - val &= ~S3C64XX_SPI_ENCLK_ENABLE; - writel(val, regs + S3C64XX_SPI_CLK_CFG); + if (sci->clk_from_cmu) { + clk_disable(sdd->src_clk); + } else { + val = readl(regs + S3C64XX_SPI_CLK_CFG); + val &= ~S3C64XX_SPI_ENCLK_ENABLE; + writel(val, regs + S3C64XX_SPI_CLK_CFG); + } /* Set Polarity and Phase */ val = readl(regs + S3C64XX_SPI_CH_CFG); @@ -429,29 +450,39 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) switch (sdd->cur_bpw) { case 32: val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD; + val |= S3C64XX_SPI_MODE_CH_TSZ_WORD; break; case 16: val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD; + val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD; break; default: val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE; + val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; break; } - val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; /* Always 8bits wide */ writel(val, regs + S3C64XX_SPI_MODE_CFG); - /* Configure Clock */ - val = readl(regs + S3C64XX_SPI_CLK_CFG); - val &= ~S3C64XX_SPI_PSR_MASK; - val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1) - & S3C64XX_SPI_PSR_MASK); - writel(val, regs + S3C64XX_SPI_CLK_CFG); - - /* Enable Clock */ - val = readl(regs + S3C64XX_SPI_CLK_CFG); - val |= S3C64XX_SPI_ENCLK_ENABLE; - writel(val, regs + S3C64XX_SPI_CLK_CFG); + if (sci->clk_from_cmu) { + /* Configure Clock */ + /* There is half-multiplier before the SPI */ + clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); + /* Enable Clock */ + clk_enable(sdd->src_clk); + } else { + /* Configure Clock */ + val = readl(regs + S3C64XX_SPI_CLK_CFG); + val &= ~S3C64XX_SPI_PSR_MASK; + val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1) + & S3C64XX_SPI_PSR_MASK); + writel(val, regs + S3C64XX_SPI_CLK_CFG); + + /* Enable Clock */ + val = readl(regs + S3C64XX_SPI_CLK_CFG); + val |= S3C64XX_SPI_ENCLK_ENABLE; + writel(val, regs + S3C64XX_SPI_CLK_CFG); + } } static void s3c64xx_spi_dma_rxcb(struct s3c2410_dma_chan *chan, void *buf_id, @@ -499,6 +530,7 @@ static void s3c64xx_spi_dma_txcb(struct s3c2410_dma_chan *chan, void *buf_id, static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd, struct spi_message *msg) { + struct s3c64xx_spi_info *sci = sdd->cntrlr_info; struct device *dev = &sdd->pdev->dev; struct spi_transfer *xfer; @@ -514,6 +546,9 @@ static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd, /* Map until end or first fail */ list_for_each_entry(xfer, &msg->transfers, transfer_list) { + if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1)) + continue; + if (xfer->tx_buf != NULL) { xfer->tx_dma = dma_map_single(dev, (void *)xfer->tx_buf, xfer->len, @@ -545,6 +580,7 @@ static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd, static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd, struct spi_message *msg) { + struct s3c64xx_spi_info *sci = sdd->cntrlr_info; struct device *dev = &sdd->pdev->dev; struct spi_transfer *xfer; @@ -553,6 +589,9 @@ static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd, list_for_each_entry(xfer, &msg->transfers, transfer_list) { + if (xfer->len <= ((sci->fifo_lvl_mask >> 1) + 1)) + continue; + if (xfer->rx_buf != NULL && xfer->rx_dma != XFER_DMAADDR_INVALID) dma_unmap_single(dev, xfer->rx_dma, @@ -608,6 +647,14 @@ static void handle_msg(struct s3c64xx_spi_driver_data *sdd, bpw = xfer->bits_per_word ? : spi->bits_per_word; speed = xfer->speed_hz ? : spi->max_speed_hz; + if (xfer->len % (bpw / 8)) { + dev_err(&spi->dev, + "Xfer length(%u) not a multiple of word size(%u)\n", + xfer->len, bpw / 8); + status = -EIO; + goto out; + } + if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) { sdd->cur_bpw = bpw; sdd->cur_speed = speed; @@ -798,7 +845,6 @@ static int s3c64xx_spi_setup(struct spi_device *spi) struct s3c64xx_spi_driver_data *sdd; struct s3c64xx_spi_info *sci; struct spi_message *msg; - u32 psr, speed; unsigned long flags; int err = 0; @@ -841,32 +887,37 @@ static int s3c64xx_spi_setup(struct spi_device *spi) } /* Check if we can provide the requested rate */ - speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1); /* Max possible */ - - if (spi->max_speed_hz > speed) - spi->max_speed_hz = speed; - - psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1; - psr &= S3C64XX_SPI_PSR_MASK; - if (psr == S3C64XX_SPI_PSR_MASK) - psr--; + if (!sci->clk_from_cmu) { + u32 psr, speed; + + /* Max possible */ + speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1); + + if (spi->max_speed_hz > speed) + spi->max_speed_hz = speed; + + psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1; + psr &= S3C64XX_SPI_PSR_MASK; + if (psr == S3C64XX_SPI_PSR_MASK) + psr--; + + speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1); + if (spi->max_speed_hz < speed) { + if (psr+1 < S3C64XX_SPI_PSR_MASK) { + psr++; + } else { + err = -EINVAL; + goto setup_exit; + } + } - speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1); - if (spi->max_speed_hz < speed) { - if (psr+1 < S3C64XX_SPI_PSR_MASK) { - psr++; - } else { + speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1); + if (spi->max_speed_hz >= speed) + spi->max_speed_hz = speed; + else err = -EINVAL; - goto setup_exit; - } } - speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1); - if (spi->max_speed_hz >= speed) - spi->max_speed_hz = speed; - else - err = -EINVAL; - setup_exit: /* setup() returns with device de-selected */ @@ -888,7 +939,8 @@ static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel) /* Disable Interrupts - we use Polling if not DMA mode */ writel(0, regs + S3C64XX_SPI_INT_EN); - writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT, + if (!sci->clk_from_cmu) + writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT, regs + S3C64XX_SPI_CLK_CFG); writel(0, regs + S3C64XX_SPI_MODE_CFG); writel(0, regs + S3C64XX_SPI_PACKET_CNT); diff --git a/drivers/spi/spi_topcliff_pch.c b/drivers/spi/spi_topcliff_pch.c new file mode 100644 index 000000000000..97746232741e --- /dev/null +++ b/drivers/spi/spi_topcliff_pch.c @@ -0,0 +1,1303 @@ +/* + * SPI bus driver for the Topcliff PCH used by Intel SoCs + * + * Copyright (C) 2010 OKI SEMICONDUCTOR Co., LTD. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. + */ + +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/wait.h> +#include <linux/spi/spi.h> +#include <linux/interrupt.h> +#include <linux/sched.h> +#include <linux/spi/spidev.h> +#include <linux/module.h> +#include <linux/device.h> + +/* Register offsets */ +#define PCH_SPCR 0x00 /* SPI control register */ +#define PCH_SPBRR 0x04 /* SPI baud rate register */ +#define PCH_SPSR 0x08 /* SPI status register */ +#define PCH_SPDWR 0x0C /* SPI write data register */ +#define PCH_SPDRR 0x10 /* SPI read data register */ +#define PCH_SSNXCR 0x18 /* SSN Expand Control Register */ +#define PCH_SRST 0x1C /* SPI reset register */ + +#define PCH_SPSR_TFD 0x000007C0 +#define PCH_SPSR_RFD 0x0000F800 + +#define PCH_READABLE(x) (((x) & PCH_SPSR_RFD)>>11) +#define PCH_WRITABLE(x) (((x) & PCH_SPSR_TFD)>>6) + +#define PCH_RX_THOLD 7 +#define PCH_RX_THOLD_MAX 15 + +#define PCH_MAX_BAUDRATE 5000000 +#define PCH_MAX_FIFO_DEPTH 16 + +#define STATUS_RUNNING 1 +#define STATUS_EXITING 2 +#define PCH_SLEEP_TIME 10 + +#define PCH_ADDRESS_SIZE 0x20 + +#define SSN_LOW 0x02U +#define SSN_NO_CONTROL 0x00U +#define PCH_MAX_CS 0xFF +#define PCI_DEVICE_ID_GE_SPI 0x8816 + +#define SPCR_SPE_BIT (1 << 0) +#define SPCR_MSTR_BIT (1 << 1) +#define SPCR_LSBF_BIT (1 << 4) +#define SPCR_CPHA_BIT (1 << 5) +#define SPCR_CPOL_BIT (1 << 6) +#define SPCR_TFIE_BIT (1 << 8) +#define SPCR_RFIE_BIT (1 << 9) +#define SPCR_FIE_BIT (1 << 10) +#define SPCR_ORIE_BIT (1 << 11) +#define SPCR_MDFIE_BIT (1 << 12) +#define SPCR_FICLR_BIT (1 << 24) +#define SPSR_TFI_BIT (1 << 0) +#define SPSR_RFI_BIT (1 << 1) +#define SPSR_FI_BIT (1 << 2) +#define SPBRR_SIZE_BIT (1 << 10) + +#define PCH_ALL (SPCR_TFIE_BIT|SPCR_RFIE_BIT|SPCR_FIE_BIT|SPCR_ORIE_BIT|SPCR_MDFIE_BIT) + +#define SPCR_RFIC_FIELD 20 +#define SPCR_TFIC_FIELD 16 + +#define SPSR_INT_BITS 0x1F +#define MASK_SPBRR_SPBR_BITS (~((1 << 10) - 1)) +#define MASK_RFIC_SPCR_BITS (~(0xf << 20)) +#define MASK_TFIC_SPCR_BITS (~(0xf000f << 12)) + +#define PCH_CLOCK_HZ 50000000 +#define PCH_MAX_SPBR 1023 + + +/** + * struct pch_spi_data - Holds the SPI channel specific details + * @io_remap_addr: The remapped PCI base address + * @master: Pointer to the SPI master structure + * @work: Reference to work queue handler + * @wk: Workqueue for carrying out execution of the + * requests + * @wait: Wait queue for waking up upon receiving an + * interrupt. + * @transfer_complete: Status of SPI Transfer + * @bcurrent_msg_processing: Status flag for message processing + * @lock: Lock for protecting this structure + * @queue: SPI Message queue + * @status: Status of the SPI driver + * @bpw_len: Length of data to be transferred in bits per + * word + * @transfer_active: Flag showing active transfer + * @tx_index: Transmit data count; for bookkeeping during + * transfer + * @rx_index: Receive data count; for bookkeeping during + * transfer + * @tx_buff: Buffer for data to be transmitted + * @rx_index: Buffer for Received data + * @n_curnt_chip: The chip number that this SPI driver currently + * operates on + * @current_chip: Reference to the current chip that this SPI + * driver currently operates on + * @current_msg: The current message that this SPI driver is + * handling + * @cur_trans: The current transfer that this SPI driver is + * handling + * @board_dat: Reference to the SPI device data structure + */ +struct pch_spi_data { + void __iomem *io_remap_addr; + struct spi_master *master; + struct work_struct work; + struct workqueue_struct *wk; + wait_queue_head_t wait; + u8 transfer_complete; + u8 bcurrent_msg_processing; + spinlock_t lock; + struct list_head queue; + u8 status; + u32 bpw_len; + u8 transfer_active; + u32 tx_index; + u32 rx_index; + u16 *pkt_tx_buff; + u16 *pkt_rx_buff; + u8 n_curnt_chip; + struct spi_device *current_chip; + struct spi_message *current_msg; + struct spi_transfer *cur_trans; + struct pch_spi_board_data *board_dat; +}; + +/** + * struct pch_spi_board_data - Holds the SPI device specific details + * @pdev: Pointer to the PCI device + * @irq_reg_sts: Status of IRQ registration + * @pci_req_sts: Status of pci_request_regions + * @suspend_sts: Status of suspend + * @data: Pointer to SPI channel data structure + */ +struct pch_spi_board_data { + struct pci_dev *pdev; + u8 irq_reg_sts; + u8 pci_req_sts; + u8 suspend_sts; + struct pch_spi_data *data; +}; + +static struct pci_device_id pch_spi_pcidev_id[] = { + {PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_GE_SPI)}, + {0,} +}; + +/** + * pch_spi_writereg() - Performs register writes + * @master: Pointer to struct spi_master. + * @idx: Register offset. + * @val: Value to be written to register. + */ +static inline void pch_spi_writereg(struct spi_master *master, int idx, u32 val) +{ + struct pch_spi_data *data = spi_master_get_devdata(master); + iowrite32(val, (data->io_remap_addr + idx)); +} + +/** + * pch_spi_readreg() - Performs register reads + * @master: Pointer to struct spi_master. + * @idx: Register offset. + */ +static inline u32 pch_spi_readreg(struct spi_master *master, int idx) +{ + struct pch_spi_data *data = spi_master_get_devdata(master); + return ioread32(data->io_remap_addr + idx); +} + +static inline void pch_spi_setclr_reg(struct spi_master *master, int idx, + u32 set, u32 clr) +{ + u32 tmp = pch_spi_readreg(master, idx); + tmp = (tmp & ~clr) | set; + pch_spi_writereg(master, idx, tmp); +} + +static void pch_spi_set_master_mode(struct spi_master *master) +{ + pch_spi_setclr_reg(master, PCH_SPCR, SPCR_MSTR_BIT, 0); +} + +/** + * pch_spi_clear_fifo() - Clears the Transmit and Receive FIFOs + * @master: Pointer to struct spi_master. + */ +static void pch_spi_clear_fifo(struct spi_master *master) +{ + pch_spi_setclr_reg(master, PCH_SPCR, SPCR_FICLR_BIT, 0); + pch_spi_setclr_reg(master, PCH_SPCR, 0, SPCR_FICLR_BIT); +} + +static void pch_spi_handler_sub(struct pch_spi_data *data, u32 reg_spsr_val, + void __iomem *io_remap_addr) +{ + u32 n_read, tx_index, rx_index, bpw_len; + u16 *pkt_rx_buffer, *pkt_tx_buff; + int read_cnt; + u32 reg_spcr_val; + void __iomem *spsr; + void __iomem *spdrr; + void __iomem *spdwr; + + spsr = io_remap_addr + PCH_SPSR; + iowrite32(reg_spsr_val, spsr); + + if (data->transfer_active) { + rx_index = data->rx_index; + tx_index = data->tx_index; + bpw_len = data->bpw_len; + pkt_rx_buffer = data->pkt_rx_buff; + pkt_tx_buff = data->pkt_tx_buff; + + spdrr = io_remap_addr + PCH_SPDRR; + spdwr = io_remap_addr + PCH_SPDWR; + + n_read = PCH_READABLE(reg_spsr_val); + + for (read_cnt = 0; (read_cnt < n_read); read_cnt++) { + pkt_rx_buffer[rx_index++] = ioread32(spdrr); + if (tx_index < bpw_len) + iowrite32(pkt_tx_buff[tx_index++], spdwr); + } + + /* disable RFI if not needed */ + if ((bpw_len - rx_index) <= PCH_MAX_FIFO_DEPTH) { + reg_spcr_val = ioread32(io_remap_addr + PCH_SPCR); + reg_spcr_val &= ~SPCR_RFIE_BIT; /* disable RFI */ + + /* reset rx threshold */ + reg_spcr_val &= MASK_RFIC_SPCR_BITS; + reg_spcr_val |= (PCH_RX_THOLD_MAX << SPCR_RFIC_FIELD); + iowrite32(((reg_spcr_val) &= (~(SPCR_RFIE_BIT))), + (io_remap_addr + PCH_SPCR)); + } + + /* update counts */ + data->tx_index = tx_index; + data->rx_index = rx_index; + + } + + /* if transfer complete interrupt */ + if (reg_spsr_val & SPSR_FI_BIT) { + /* disable FI & RFI interrupts */ + pch_spi_setclr_reg(data->master, PCH_SPCR, 0, + SPCR_FIE_BIT | SPCR_TFIE_BIT); + + /* transfer is completed;inform pch_spi_process_messages */ + data->transfer_complete = true; + wake_up(&data->wait); + } +} + +/** + * pch_spi_handler() - Interrupt handler + * @irq: The interrupt number. + * @dev_id: Pointer to struct pch_spi_board_data. + */ +static irqreturn_t pch_spi_handler(int irq, void *dev_id) +{ + u32 reg_spsr_val; + struct pch_spi_data *data; + void __iomem *spsr; + void __iomem *io_remap_addr; + irqreturn_t ret = IRQ_NONE; + struct pch_spi_board_data *board_dat = dev_id; + + if (board_dat->suspend_sts) { + dev_dbg(&board_dat->pdev->dev, + "%s returning due to suspend\n", __func__); + return IRQ_NONE; + } + + data = board_dat->data; + io_remap_addr = data->io_remap_addr; + spsr = io_remap_addr + PCH_SPSR; + + reg_spsr_val = ioread32(spsr); + + /* Check if the interrupt is for SPI device */ + if (reg_spsr_val & (SPSR_FI_BIT | SPSR_RFI_BIT)) { + pch_spi_handler_sub(data, reg_spsr_val, io_remap_addr); + ret = IRQ_HANDLED; + } + + dev_dbg(&board_dat->pdev->dev, "%s EXIT return value=%d\n", + __func__, ret); + + return ret; +} + +/** + * pch_spi_set_baud_rate() - Sets SPBR field in SPBRR + * @master: Pointer to struct spi_master. + * @speed_hz: Baud rate. + */ +static void pch_spi_set_baud_rate(struct spi_master *master, u32 speed_hz) +{ + u32 n_spbr = PCH_CLOCK_HZ / (speed_hz * 2); + + /* if baud rate is less than we can support limit it */ + if (n_spbr > PCH_MAX_SPBR) + n_spbr = PCH_MAX_SPBR; + + pch_spi_setclr_reg(master, PCH_SPBRR, n_spbr, ~MASK_SPBRR_SPBR_BITS); +} + +/** + * pch_spi_set_bits_per_word() - Sets SIZE field in SPBRR + * @master: Pointer to struct spi_master. + * @bits_per_word: Bits per word for SPI transfer. + */ +static void pch_spi_set_bits_per_word(struct spi_master *master, + u8 bits_per_word) +{ + if (bits_per_word == 8) + pch_spi_setclr_reg(master, PCH_SPBRR, 0, SPBRR_SIZE_BIT); + else + pch_spi_setclr_reg(master, PCH_SPBRR, SPBRR_SIZE_BIT, 0); +} + +/** + * pch_spi_setup_transfer() - Configures the PCH SPI hardware for transfer + * @spi: Pointer to struct spi_device. + */ +static void pch_spi_setup_transfer(struct spi_device *spi) +{ + u32 flags = 0; + + dev_dbg(&spi->dev, "%s SPBRR content =%x setting baud rate=%d\n", + __func__, pch_spi_readreg(spi->master, PCH_SPBRR), + spi->max_speed_hz); + pch_spi_set_baud_rate(spi->master, spi->max_speed_hz); + + /* set bits per word */ + pch_spi_set_bits_per_word(spi->master, spi->bits_per_word); + + if (!(spi->mode & SPI_LSB_FIRST)) + flags |= SPCR_LSBF_BIT; + if (spi->mode & SPI_CPOL) + flags |= SPCR_CPOL_BIT; + if (spi->mode & SPI_CPHA) + flags |= SPCR_CPHA_BIT; + pch_spi_setclr_reg(spi->master, PCH_SPCR, flags, + (SPCR_LSBF_BIT | SPCR_CPOL_BIT | SPCR_CPHA_BIT)); + + /* Clear the FIFO by toggling FICLR to 1 and back to 0 */ + pch_spi_clear_fifo(spi->master); +} + +/** + * pch_spi_reset() - Clears SPI registers + * @master: Pointer to struct spi_master. + */ +static void pch_spi_reset(struct spi_master *master) +{ + /* write 1 to reset SPI */ + pch_spi_writereg(master, PCH_SRST, 0x1); + + /* clear reset */ + pch_spi_writereg(master, PCH_SRST, 0x0); +} + +static int pch_spi_setup(struct spi_device *pspi) +{ + /* check bits per word */ + if (pspi->bits_per_word == 0) { + pspi->bits_per_word = 8; + dev_dbg(&pspi->dev, "%s 8 bits per word\n", __func__); + } + + if ((pspi->bits_per_word != 8) && (pspi->bits_per_word != 16)) { + dev_err(&pspi->dev, "%s Invalid bits per word\n", __func__); + return -EINVAL; + } + + /* Check baud rate setting */ + /* if baud rate of chip is greater than + max we can support,return error */ + if ((pspi->max_speed_hz) > PCH_MAX_BAUDRATE) + pspi->max_speed_hz = PCH_MAX_BAUDRATE; + + dev_dbg(&pspi->dev, "%s MODE = %x\n", __func__, + (pspi->mode) & (SPI_CPOL | SPI_CPHA)); + + return 0; +} + +static int pch_spi_transfer(struct spi_device *pspi, struct spi_message *pmsg) +{ + + struct spi_transfer *transfer; + struct pch_spi_data *data = spi_master_get_devdata(pspi->master); + int retval; + unsigned long flags; + + /* validate spi message and baud rate */ + if (unlikely(list_empty(&pmsg->transfers) == 1)) { + dev_err(&pspi->dev, "%s list empty\n", __func__); + retval = -EINVAL; + goto err_out; + } + + if (unlikely(pspi->max_speed_hz == 0)) { + dev_err(&pspi->dev, "%s pch_spi_tranfer maxspeed=%d\n", + __func__, pspi->max_speed_hz); + retval = -EINVAL; + goto err_out; + } + + dev_dbg(&pspi->dev, "%s Transfer List not empty. " + "Transfer Speed is set.\n", __func__); + + /* validate Tx/Rx buffers and Transfer length */ + list_for_each_entry(transfer, &pmsg->transfers, transfer_list) { + if (!transfer->tx_buf && !transfer->rx_buf) { + dev_err(&pspi->dev, + "%s Tx and Rx buffer NULL\n", __func__); + retval = -EINVAL; + goto err_out; + } + + if (!transfer->len) { + dev_err(&pspi->dev, "%s Transfer length invalid\n", + __func__); + retval = -EINVAL; + goto err_out; + } + + dev_dbg(&pspi->dev, "%s Tx/Rx buffer valid. Transfer length" + " valid\n", __func__); + + /* if baud rate hs been specified validate the same */ + if (transfer->speed_hz > PCH_MAX_BAUDRATE) + transfer->speed_hz = PCH_MAX_BAUDRATE; + + /* if bits per word has been specified validate the same */ + if (transfer->bits_per_word) { + if ((transfer->bits_per_word != 8) + && (transfer->bits_per_word != 16)) { + retval = -EINVAL; + dev_err(&pspi->dev, + "%s Invalid bits per word\n", __func__); + goto err_out; + } + } + } + + spin_lock_irqsave(&data->lock, flags); + + /* We won't process any messages if we have been asked to terminate */ + if (data->status == STATUS_EXITING) { + dev_err(&pspi->dev, "%s status = STATUS_EXITING.\n", __func__); + retval = -ESHUTDOWN; + goto err_return_spinlock; + } + + /* If suspended ,return -EINVAL */ + if (data->board_dat->suspend_sts) { + dev_err(&pspi->dev, "%s suspend; returning EINVAL\n", __func__); + retval = -EINVAL; + goto err_return_spinlock; + } + + /* set status of message */ + pmsg->actual_length = 0; + dev_dbg(&pspi->dev, "%s - pmsg->status =%d\n", __func__, pmsg->status); + + pmsg->status = -EINPROGRESS; + + /* add message to queue */ + list_add_tail(&pmsg->queue, &data->queue); + dev_dbg(&pspi->dev, "%s - Invoked list_add_tail\n", __func__); + + /* schedule work queue to run */ + queue_work(data->wk, &data->work); + dev_dbg(&pspi->dev, "%s - Invoked queue work\n", __func__); + + retval = 0; + +err_return_spinlock: + spin_unlock_irqrestore(&data->lock, flags); +err_out: + dev_dbg(&pspi->dev, "%s RETURN=%d\n", __func__, retval); + return retval; +} + +static inline void pch_spi_select_chip(struct pch_spi_data *data, + struct spi_device *pspi) +{ + if (data->current_chip != NULL) { + if (pspi->chip_select != data->n_curnt_chip) { + dev_dbg(&pspi->dev, "%s : different slave\n", __func__); + data->current_chip = NULL; + } + } + + data->current_chip = pspi; + + data->n_curnt_chip = data->current_chip->chip_select; + + dev_dbg(&pspi->dev, "%s :Invoking pch_spi_setup_transfer\n", __func__); + pch_spi_setup_transfer(pspi); +} + +static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw, + struct spi_message **ppmsg) +{ + int size; + u32 n_writes; + int j; + struct spi_message *pmsg; + const u8 *tx_buf; + const u16 *tx_sbuf; + + pmsg = *ppmsg; + + /* set baud rate if needed */ + if (data->cur_trans->speed_hz) { + dev_dbg(&data->master->dev, "%s:setting baud rate\n", __func__); + pch_spi_set_baud_rate(data->master, data->cur_trans->speed_hz); + } + + /* set bits per word if needed */ + if (data->cur_trans->bits_per_word && + (data->current_msg->spi->bits_per_word != data->cur_trans->bits_per_word)) { + dev_dbg(&data->master->dev, "%s:set bits per word\n", __func__); + pch_spi_set_bits_per_word(data->master, + data->cur_trans->bits_per_word); + *bpw = data->cur_trans->bits_per_word; + } else { + *bpw = data->current_msg->spi->bits_per_word; + } + + /* reset Tx/Rx index */ + data->tx_index = 0; + data->rx_index = 0; + + data->bpw_len = data->cur_trans->len / (*bpw / 8); + + /* find alloc size */ + size = data->cur_trans->len * sizeof(*data->pkt_tx_buff); + + /* allocate memory for pkt_tx_buff & pkt_rx_buffer */ + data->pkt_tx_buff = kzalloc(size, GFP_KERNEL); + if (data->pkt_tx_buff != NULL) { + data->pkt_rx_buff = kzalloc(size, GFP_KERNEL); + if (!data->pkt_rx_buff) + kfree(data->pkt_tx_buff); + } + + if (!data->pkt_rx_buff) { + /* flush queue and set status of all transfers to -ENOMEM */ + dev_err(&data->master->dev, "%s :kzalloc failed\n", __func__); + list_for_each_entry(pmsg, data->queue.next, queue) { + pmsg->status = -ENOMEM; + + if (pmsg->complete != 0) + pmsg->complete(pmsg->context); + + /* delete from queue */ + list_del_init(&pmsg->queue); + } + return; + } + + /* copy Tx Data */ + if (data->cur_trans->tx_buf != NULL) { + if (*bpw == 8) { + tx_buf = data->cur_trans->tx_buf; + for (j = 0; j < data->bpw_len; j++) + data->pkt_tx_buff[j] = *tx_buf++; + } else { + tx_sbuf = data->cur_trans->tx_buf; + for (j = 0; j < data->bpw_len; j++) + data->pkt_tx_buff[j] = *tx_sbuf++; + } + } + + /* if len greater than PCH_MAX_FIFO_DEPTH, write 16,else len bytes */ + n_writes = data->bpw_len; + if (n_writes > PCH_MAX_FIFO_DEPTH) + n_writes = PCH_MAX_FIFO_DEPTH; + + dev_dbg(&data->master->dev, "\n%s:Pulling down SSN low - writing " + "0x2 to SSNXCR\n", __func__); + pch_spi_writereg(data->master, PCH_SSNXCR, SSN_LOW); + + for (j = 0; j < n_writes; j++) + pch_spi_writereg(data->master, PCH_SPDWR, data->pkt_tx_buff[j]); + + /* update tx_index */ + data->tx_index = j; + + /* reset transfer complete flag */ + data->transfer_complete = false; + data->transfer_active = true; +} + + +static void pch_spi_nomore_transfer(struct pch_spi_data *data, + struct spi_message *pmsg) +{ + dev_dbg(&data->master->dev, "%s called\n", __func__); + /* Invoke complete callback + * [To the spi core..indicating end of transfer] */ + data->current_msg->status = 0; + + if (data->current_msg->complete != 0) { + dev_dbg(&data->master->dev, + "%s:Invoking callback of SPI core\n", __func__); + data->current_msg->complete(data->current_msg->context); + } + + /* update status in global variable */ + data->bcurrent_msg_processing = false; + + dev_dbg(&data->master->dev, + "%s:data->bcurrent_msg_processing = false\n", __func__); + + data->current_msg = NULL; + data->cur_trans = NULL; + + /* check if we have items in list and not suspending + * return 1 if list empty */ + if ((list_empty(&data->queue) == 0) && + (!data->board_dat->suspend_sts) && + (data->status != STATUS_EXITING)) { + /* We have some more work to do (either there is more tranint + * bpw;sfer requests in the current message or there are + *more messages) + */ + dev_dbg(&data->master->dev, "%s:Invoke queue_work\n", __func__); + queue_work(data->wk, &data->work); + } else if (data->board_dat->suspend_sts || + data->status == STATUS_EXITING) { + dev_dbg(&data->master->dev, + "%s suspend/remove initiated, flushing queue\n", + __func__); + list_for_each_entry(pmsg, data->queue.next, queue) { + pmsg->status = -EIO; + + if (pmsg->complete) + pmsg->complete(pmsg->context); + + /* delete from queue */ + list_del_init(&pmsg->queue); + } + } +} + +static void pch_spi_set_ir(struct pch_spi_data *data) +{ + /* enable interrupts */ + if ((data->bpw_len) > PCH_MAX_FIFO_DEPTH) { + /* set receive threhold to PCH_RX_THOLD */ + pch_spi_setclr_reg(data->master, PCH_SPCR, + PCH_RX_THOLD << SPCR_TFIC_FIELD, + ~MASK_TFIC_SPCR_BITS); + /* enable FI and RFI interrupts */ + pch_spi_setclr_reg(data->master, PCH_SPCR, + SPCR_RFIE_BIT | SPCR_TFIE_BIT, 0); + } else { + /* set receive threhold to maximum */ + pch_spi_setclr_reg(data->master, PCH_SPCR, + PCH_RX_THOLD_MAX << SPCR_TFIC_FIELD, + ~MASK_TFIC_SPCR_BITS); + /* enable FI interrupt */ + pch_spi_setclr_reg(data->master, PCH_SPCR, SPCR_FIE_BIT, 0); + } + + dev_dbg(&data->master->dev, + "%s:invoking pch_spi_set_enable to enable SPI\n", __func__); + + /* SPI set enable */ + pch_spi_setclr_reg(data->current_chip->master, PCH_SPCR, SPCR_SPE_BIT, 0); + + /* Wait until the transfer completes; go to sleep after + initiating the transfer. */ + dev_dbg(&data->master->dev, + "%s:waiting for transfer to get over\n", __func__); + + wait_event_interruptible(data->wait, data->transfer_complete); + + pch_spi_writereg(data->master, PCH_SSNXCR, SSN_NO_CONTROL); + dev_dbg(&data->master->dev, + "%s:no more control over SSN-writing 0 to SSNXCR.", __func__); + + data->transfer_active = false; + dev_dbg(&data->master->dev, + "%s set data->transfer_active = false\n", __func__); + + /* clear all interrupts */ + pch_spi_writereg(data->master, PCH_SPSR, + pch_spi_readreg(data->master, PCH_SPSR)); + /* disable interrupts */ + pch_spi_setclr_reg(data->master, PCH_SPCR, 0, PCH_ALL); +} + +static void pch_spi_copy_rx_data(struct pch_spi_data *data, int bpw) +{ + int j; + u8 *rx_buf; + u16 *rx_sbuf; + + /* copy Rx Data */ + if (!data->cur_trans->rx_buf) + return; + + if (bpw == 8) { + rx_buf = data->cur_trans->rx_buf; + for (j = 0; j < data->bpw_len; j++) + *rx_buf++ = data->pkt_rx_buff[j] & 0xFF; + } else { + rx_sbuf = data->cur_trans->rx_buf; + for (j = 0; j < data->bpw_len; j++) + *rx_sbuf++ = data->pkt_rx_buff[j]; + } +} + + +static void pch_spi_process_messages(struct work_struct *pwork) +{ + struct spi_message *pmsg; + struct pch_spi_data *data; + int bpw; + + dev_dbg(&data->master->dev, "%s data initialized\n", __func__); + data = container_of(pwork, struct pch_spi_data, work); + + spin_lock(&data->lock); + + /* check if suspend has been initiated;if yes flush queue */ + if (data->board_dat->suspend_sts || (data->status == STATUS_EXITING)) { + dev_dbg(&data->master->dev, + "%s suspend/remove initiated,flushing queue\n", + __func__); + + list_for_each_entry(pmsg, data->queue.next, queue) { + pmsg->status = -EIO; + + if (pmsg->complete != 0) { + spin_unlock(&data->lock); + pmsg->complete(pmsg->context); + spin_lock(&data->lock); + } + + /* delete from queue */ + list_del_init(&pmsg->queue); + } + + spin_unlock(&data->lock); + return; + } + + data->bcurrent_msg_processing = true; + dev_dbg(&data->master->dev, + "%s Set data->bcurrent_msg_processing= true\n", __func__); + + /* Get the message from the queue and delete it from there. */ + data->current_msg = list_entry(data->queue.next, struct spi_message, + queue); + + list_del_init(&data->current_msg->queue); + + data->current_msg->status = 0; + + pch_spi_select_chip(data, data->current_msg->spi); + + spin_unlock(&data->lock); + + do { + /* If we are already processing a message get the next + transfer structure from the message otherwise retrieve + the 1st transfer request from the message. */ + spin_lock(&data->lock); + + if (data->cur_trans == NULL) { + data->cur_trans = + list_entry(data->current_msg->transfers. + next, struct spi_transfer, + transfer_list); + dev_dbg(&data->master->dev, + "%s :Getting 1st transfer message\n", __func__); + } else { + data->cur_trans = + list_entry(data->cur_trans->transfer_list.next, + struct spi_transfer, + transfer_list); + dev_dbg(&data->master->dev, + "%s :Getting next transfer message\n", + __func__); + } + + spin_unlock(&data->lock); + + pch_spi_set_tx(data, &bpw, &pmsg); + + /* Control interrupt*/ + pch_spi_set_ir(data); + + /* Disable SPI transfer */ + pch_spi_setclr_reg(data->current_chip->master, PCH_SPCR, 0, + SPCR_SPE_BIT); + + /* clear FIFO */ + pch_spi_clear_fifo(data->master); + + /* copy Rx Data */ + pch_spi_copy_rx_data(data, bpw); + + /* free memory */ + kfree(data->pkt_rx_buff); + data->pkt_rx_buff = NULL; + + kfree(data->pkt_tx_buff); + data->pkt_tx_buff = NULL; + + /* increment message count */ + data->current_msg->actual_length += data->cur_trans->len; + + dev_dbg(&data->master->dev, + "%s:data->current_msg->actual_length=%d\n", + __func__, data->current_msg->actual_length); + + /* check for delay */ + if (data->cur_trans->delay_usecs) { + dev_dbg(&data->master->dev, "%s:" + "delay in usec=%d\n", __func__, + data->cur_trans->delay_usecs); + udelay(data->cur_trans->delay_usecs); + } + + spin_lock(&data->lock); + + /* No more transfer in this message. */ + if ((data->cur_trans->transfer_list.next) == + &(data->current_msg->transfers)) { + pch_spi_nomore_transfer(data, pmsg); + } + + spin_unlock(&data->lock); + + } while (data->cur_trans != NULL); +} + +static void pch_spi_free_resources(struct pch_spi_board_data *board_dat) +{ + dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__); + + /* free workqueue */ + if (board_dat->data->wk != NULL) { + destroy_workqueue(board_dat->data->wk); + board_dat->data->wk = NULL; + dev_dbg(&board_dat->pdev->dev, + "%s destroy_workqueue invoked successfully\n", + __func__); + } + + /* disable interrupts & free IRQ */ + if (board_dat->irq_reg_sts) { + /* disable interrupts */ + pch_spi_setclr_reg(board_dat->data->master, PCH_SPCR, 0, + PCH_ALL); + + /* free IRQ */ + free_irq(board_dat->pdev->irq, board_dat); + + dev_dbg(&board_dat->pdev->dev, + "%s free_irq invoked successfully\n", __func__); + + board_dat->irq_reg_sts = false; + } + + /* unmap PCI base address */ + if (board_dat->data->io_remap_addr != 0) { + pci_iounmap(board_dat->pdev, board_dat->data->io_remap_addr); + + board_dat->data->io_remap_addr = 0; + + dev_dbg(&board_dat->pdev->dev, + "%s pci_iounmap invoked successfully\n", __func__); + } + + /* release PCI region */ + if (board_dat->pci_req_sts) { + pci_release_regions(board_dat->pdev); + dev_dbg(&board_dat->pdev->dev, + "%s pci_release_regions invoked successfully\n", + __func__); + board_dat->pci_req_sts = false; + } +} + +static int pch_spi_get_resources(struct pch_spi_board_data *board_dat) +{ + void __iomem *io_remap_addr; + int retval; + dev_dbg(&board_dat->pdev->dev, "%s ENTRY\n", __func__); + + /* create workqueue */ + board_dat->data->wk = create_singlethread_workqueue(KBUILD_MODNAME); + if (!board_dat->data->wk) { + dev_err(&board_dat->pdev->dev, + "%s create_singlet hread_workqueue failed\n", __func__); + retval = -EBUSY; + goto err_return; + } + + dev_dbg(&board_dat->pdev->dev, + "%s create_singlethread_workqueue success\n", __func__); + + retval = pci_request_regions(board_dat->pdev, KBUILD_MODNAME); + if (retval != 0) { + dev_err(&board_dat->pdev->dev, + "%s request_region failed\n", __func__); + goto err_return; + } + + board_dat->pci_req_sts = true; + + io_remap_addr = pci_iomap(board_dat->pdev, 1, 0); + if (io_remap_addr == 0) { + dev_err(&board_dat->pdev->dev, + "%s pci_iomap failed\n", __func__); + retval = -ENOMEM; + goto err_return; + } + + /* calculate base address for all channels */ + board_dat->data->io_remap_addr = io_remap_addr; + + /* reset PCH SPI h/w */ + pch_spi_reset(board_dat->data->master); + dev_dbg(&board_dat->pdev->dev, + "%s pch_spi_reset invoked successfully\n", __func__); + + /* register IRQ */ + retval = request_irq(board_dat->pdev->irq, pch_spi_handler, + IRQF_SHARED, KBUILD_MODNAME, board_dat); + if (retval != 0) { + dev_err(&board_dat->pdev->dev, + "%s request_irq failed\n", __func__); + goto err_return; + } + + dev_dbg(&board_dat->pdev->dev, "%s request_irq returned=%d\n", + __func__, retval); + + board_dat->irq_reg_sts = true; + dev_dbg(&board_dat->pdev->dev, "%s data->irq_reg_sts=true\n", __func__); + +err_return: + if (retval != 0) { + dev_err(&board_dat->pdev->dev, + "%s FAIL:invoking pch_spi_free_resources\n", __func__); + pch_spi_free_resources(board_dat); + } + + dev_dbg(&board_dat->pdev->dev, "%s Return=%d\n", __func__, retval); + + return retval; +} + +static int pch_spi_probe(struct pci_dev *pdev, const struct pci_device_id *id) +{ + + struct spi_master *master; + + struct pch_spi_board_data *board_dat; + int retval; + + dev_dbg(&pdev->dev, "%s ENTRY\n", __func__); + + /* allocate memory for private data */ + board_dat = kzalloc(sizeof(struct pch_spi_board_data), GFP_KERNEL); + if (board_dat == NULL) { + dev_err(&pdev->dev, + " %s memory allocation for private data failed\n", + __func__); + retval = -ENOMEM; + goto err_kmalloc; + } + + dev_dbg(&pdev->dev, + "%s memory allocation for private data success\n", __func__); + + /* enable PCI device */ + retval = pci_enable_device(pdev); + if (retval != 0) { + dev_err(&pdev->dev, "%s pci_enable_device FAILED\n", __func__); + + goto err_pci_en_device; + } + + dev_dbg(&pdev->dev, "%s pci_enable_device returned=%d\n", + __func__, retval); + + board_dat->pdev = pdev; + + /* alllocate memory for SPI master */ + master = spi_alloc_master(&pdev->dev, sizeof(struct pch_spi_data)); + if (master == NULL) { + retval = -ENOMEM; + dev_err(&pdev->dev, "%s Fail.\n", __func__); + goto err_spi_alloc_master; + } + + dev_dbg(&pdev->dev, + "%s spi_alloc_master returned non NULL\n", __func__); + + /* initialize members of SPI master */ + master->bus_num = -1; + master->num_chipselect = PCH_MAX_CS; + master->setup = pch_spi_setup; + master->transfer = pch_spi_transfer; + dev_dbg(&pdev->dev, + "%s transfer member of SPI master initialized\n", __func__); + + board_dat->data = spi_master_get_devdata(master); + + board_dat->data->master = master; + board_dat->data->n_curnt_chip = 255; + board_dat->data->board_dat = board_dat; + board_dat->data->status = STATUS_RUNNING; + + INIT_LIST_HEAD(&board_dat->data->queue); + spin_lock_init(&board_dat->data->lock); + INIT_WORK(&board_dat->data->work, pch_spi_process_messages); + init_waitqueue_head(&board_dat->data->wait); + + /* allocate resources for PCH SPI */ + retval = pch_spi_get_resources(board_dat); + if (retval) { + dev_err(&pdev->dev, "%s fail(retval=%d)\n", __func__, retval); + goto err_spi_get_resources; + } + + dev_dbg(&pdev->dev, "%s pch_spi_get_resources returned=%d\n", + __func__, retval); + + /* save private data in dev */ + pci_set_drvdata(pdev, board_dat); + dev_dbg(&pdev->dev, "%s invoked pci_set_drvdata\n", __func__); + + /* set master mode */ + pch_spi_set_master_mode(master); + dev_dbg(&pdev->dev, + "%s invoked pch_spi_set_master_mode\n", __func__); + + /* Register the controller with the SPI core. */ + retval = spi_register_master(master); + if (retval != 0) { + dev_err(&pdev->dev, + "%s spi_register_master FAILED\n", __func__); + goto err_spi_reg_master; + } + + dev_dbg(&pdev->dev, "%s spi_register_master returned=%d\n", + __func__, retval); + + + return 0; + +err_spi_reg_master: + spi_unregister_master(master); +err_spi_get_resources: +err_spi_alloc_master: + spi_master_put(master); + pci_disable_device(pdev); +err_pci_en_device: + kfree(board_dat); +err_kmalloc: + return retval; +} + +static void pch_spi_remove(struct pci_dev *pdev) +{ + struct pch_spi_board_data *board_dat = pci_get_drvdata(pdev); + int count; + + dev_dbg(&pdev->dev, "%s ENTRY\n", __func__); + + if (!board_dat) { + dev_err(&pdev->dev, + "%s pci_get_drvdata returned NULL\n", __func__); + return; + } + + /* check for any pending messages; no action is taken if the queue + * is still full; but at least we tried. Unload anyway */ + count = 500; + spin_lock(&board_dat->data->lock); + board_dat->data->status = STATUS_EXITING; + while ((list_empty(&board_dat->data->queue) == 0) && --count) { + dev_dbg(&board_dat->pdev->dev, "%s :queue not empty\n", + __func__); + spin_unlock(&board_dat->data->lock); + msleep(PCH_SLEEP_TIME); + spin_lock(&board_dat->data->lock); + } + spin_unlock(&board_dat->data->lock); + + /* Free resources allocated for PCH SPI */ + pch_spi_free_resources(board_dat); + + spi_unregister_master(board_dat->data->master); + + /* free memory for private data */ + kfree(board_dat); + + pci_set_drvdata(pdev, NULL); + + /* disable PCI device */ + pci_disable_device(pdev); + + dev_dbg(&pdev->dev, "%s invoked pci_disable_device\n", __func__); +} + +#ifdef CONFIG_PM +static int pch_spi_suspend(struct pci_dev *pdev, pm_message_t state) +{ + u8 count; + int retval; + + struct pch_spi_board_data *board_dat = pci_get_drvdata(pdev); + + dev_dbg(&pdev->dev, "%s ENTRY\n", __func__); + + if (!board_dat) { + dev_err(&pdev->dev, + "%s pci_get_drvdata returned NULL\n", __func__); + return -EFAULT; + } + + retval = 0; + board_dat->suspend_sts = true; + + /* check if the current message is processed: + Only after thats done the transfer will be suspended */ + count = 255; + while ((--count) > 0) { + if (!(board_dat->data->bcurrent_msg_processing)) { + dev_dbg(&pdev->dev, "%s board_dat->data->bCurrent_" + "msg_processing = false\n", __func__); + break; + } else { + dev_dbg(&pdev->dev, "%s board_dat->data->bCurrent_msg_" + "processing = true\n", __func__); + } + msleep(PCH_SLEEP_TIME); + } + + /* Free IRQ */ + if (board_dat->irq_reg_sts) { + /* disable all interrupts */ + pch_spi_setclr_reg(board_dat->data->master, PCH_SPCR, 0, + PCH_ALL); + pch_spi_reset(board_dat->data->master); + + free_irq(board_dat->pdev->irq, board_dat); + + board_dat->irq_reg_sts = false; + dev_dbg(&pdev->dev, + "%s free_irq invoked successfully.\n", __func__); + } + + /* save config space */ + retval = pci_save_state(pdev); + + if (retval == 0) { + dev_dbg(&pdev->dev, "%s pci_save_state returned=%d\n", + __func__, retval); + /* disable PM notifications */ + pci_enable_wake(pdev, PCI_D3hot, 0); + dev_dbg(&pdev->dev, + "%s pci_enable_wake invoked successfully\n", __func__); + /* disable PCI device */ + pci_disable_device(pdev); + dev_dbg(&pdev->dev, + "%s pci_disable_device invoked successfully\n", + __func__); + /* move device to D3hot state */ + pci_set_power_state(pdev, PCI_D3hot); + dev_dbg(&pdev->dev, + "%s pci_set_power_state invoked successfully\n", + __func__); + } else { + dev_err(&pdev->dev, "%s pci_save_state failed\n", __func__); + } + + dev_dbg(&pdev->dev, "%s return=%d\n", __func__, retval); + + return retval; +} + +static int pch_spi_resume(struct pci_dev *pdev) +{ + int retval; + + struct pch_spi_board_data *board = pci_get_drvdata(pdev); + dev_dbg(&pdev->dev, "%s ENTRY\n", __func__); + + if (!board) { + dev_err(&pdev->dev, + "%s pci_get_drvdata returned NULL\n", __func__); + return -EFAULT; + } + + /* move device to DO power state */ + pci_set_power_state(pdev, PCI_D0); + + /* restore state */ + pci_restore_state(pdev); + + retval = pci_enable_device(pdev); + if (retval < 0) { + dev_err(&pdev->dev, + "%s pci_enable_device failed\n", __func__); + } else { + /* disable PM notifications */ + pci_enable_wake(pdev, PCI_D3hot, 0); + + /* register IRQ handler */ + if (!board->irq_reg_sts) { + /* register IRQ */ + retval = request_irq(board->pdev->irq, pch_spi_handler, + IRQF_SHARED, KBUILD_MODNAME, + board); + if (retval < 0) { + dev_err(&pdev->dev, + "%s request_irq failed\n", __func__); + return retval; + } + board->irq_reg_sts = true; + + /* reset PCH SPI h/w */ + pch_spi_reset(board->data->master); + pch_spi_set_master_mode(board->data->master); + + /* set suspend status to false */ + board->suspend_sts = false; + + } + } + + dev_dbg(&pdev->dev, "%s returning=%d\n", __func__, retval); + + return retval; +} +#else +#define pch_spi_suspend NULL +#define pch_spi_resume NULL + +#endif + +static struct pci_driver pch_spi_pcidev = { + .name = "pch_spi", + .id_table = pch_spi_pcidev_id, + .probe = pch_spi_probe, + .remove = pch_spi_remove, + .suspend = pch_spi_suspend, + .resume = pch_spi_resume, +}; + +static int __init pch_spi_init(void) +{ + return pci_register_driver(&pch_spi_pcidev); +} +module_init(pch_spi_init); + +static void __exit pch_spi_exit(void) +{ + pci_unregister_driver(&pch_spi_pcidev); +} +module_exit(pch_spi_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Topcliff PCH SPI PCI Driver"); |