summaryrefslogtreecommitdiffstats
path: root/drivers/spi/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/spi/Kconfig')
-rw-r--r--drivers/spi/Kconfig109
1 files changed, 109 insertions, 0 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
new file mode 100644
index 000000000000..b77dbd63e596
--- /dev/null
+++ b/drivers/spi/Kconfig
@@ -0,0 +1,109 @@
+#
+# SPI driver configuration
+#
+# NOTE: the reason this doesn't show SPI slave support is mostly that
+# nobody's needed a slave side API yet. The master-role API is not
+# fully appropriate there, so it'd need some thought to do well.
+#
+menu "SPI support"
+
+config SPI
+ bool "SPI support"
+ help
+ The "Serial Peripheral Interface" is a low level synchronous
+ protocol. Chips that support SPI can have data transfer rates
+ up to several tens of Mbit/sec. Chips are addressed with a
+ controller and a chipselect. Most SPI slaves don't support
+ dynamic device discovery; some are even write-only or read-only.
+
+ SPI is widely used by microcontollers to talk with sensors,
+ eeprom and flash memory, codecs and various other controller
+ chips, analog to digital (and d-to-a) converters, and more.
+ MMC and SD cards can be accessed using SPI protocol; and for
+ DataFlash cards used in MMC sockets, SPI must always be used.
+
+ SPI is one of a family of similar protocols using a four wire
+ interface (select, clock, data in, data out) including Microwire
+ (half duplex), SSP, SSI, and PSP. This driver framework should
+ work with most such devices and controllers.
+
+config SPI_DEBUG
+ boolean "Debug support for SPI drivers"
+ depends on SPI && DEBUG_KERNEL
+ help
+ Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
+ sysfs, and debugfs support in SPI controller and protocol drivers.
+
+#
+# MASTER side ... talking to discrete SPI slave chips including microcontrollers
+#
+
+config SPI_MASTER
+# boolean "SPI Master Support"
+ boolean
+ default SPI
+ help
+ If your system has an master-capable SPI controller (which
+ provides the clock and chipselect), you can enable that
+ controller and the protocol drivers for the SPI slave chips
+ that are connected.
+
+comment "SPI Master Controller Drivers"
+ depends on SPI_MASTER
+
+config SPI_BITBANG
+ tristate "Bitbanging SPI master"
+ depends on SPI_MASTER && EXPERIMENTAL
+ help
+ With a few GPIO pins, your system can bitbang the SPI protocol.
+ Select this to get SPI support through I/O pins (GPIO, parallel
+ port, etc). Or, some systems' SPI master controller drivers use
+ this code to manage the per-word or per-transfer accesses to the
+ hardware shift registers.
+
+ This is library code, and is automatically selected by drivers that
+ need it. You only need to select this explicitly to support driver
+ modules that aren't part of this kernel tree.
+
+config SPI_BUTTERFLY
+ tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
+ depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This uses a custom parallel port cable to connect to an AVR
+ Butterfly <http://www.atmel.com/products/avr/butterfly>, an
+ inexpensive battery powered microcontroller evaluation board.
+ This same cable can be used to flash new firmware.
+
+config SPI_BUTTERFLY
+ tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
+ depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This uses a custom parallel port cable to connect to an AVR
+ Butterfly <http://www.atmel.com/products/avr/butterfly>, an
+ inexpensive battery powered microcontroller evaluation board.
+ This same cable can be used to flash new firmware.
+
+#
+# Add new SPI master controllers in alphabetical order above this line
+#
+
+
+#
+# There are lots of SPI device types, with sensors and memory
+# being probably the most widely used ones.
+#
+comment "SPI Protocol Masters"
+ depends on SPI_MASTER
+
+
+#
+# Add new SPI protocol masters in alphabetical order above this line
+#
+
+
+# (slave support would go here)
+
+endmenu # "SPI support"
+