summaryrefslogtreecommitdiffstats
path: root/drivers/pcmcia
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pcmcia')
-rw-r--r--drivers/pcmcia/Kconfig21
-rw-r--r--drivers/pcmcia/Makefile12
-rw-r--r--drivers/pcmcia/au1000_db1x00.c305
-rw-r--r--drivers/pcmcia/au1000_generic.c10
-rw-r--r--drivers/pcmcia/au1000_generic.h18
-rw-r--r--drivers/pcmcia/au1000_pb1x00.c119
-rw-r--r--drivers/pcmcia/au1000_xxs1500.c188
-rw-r--r--drivers/pcmcia/db1xxx_ss.c623
-rw-r--r--drivers/pcmcia/xxs1500_ss.c350
9 files changed, 1003 insertions, 643 deletions
diff --git a/drivers/pcmcia/Kconfig b/drivers/pcmcia/Kconfig
index e8f35dac2d51..0a6601c76809 100644
--- a/drivers/pcmcia/Kconfig
+++ b/drivers/pcmcia/Kconfig
@@ -173,6 +173,27 @@ config PCMCIA_AU1X00
tristate "Au1x00 pcmcia support"
depends on SOC_AU1X00 && PCMCIA
+config PCMCIA_ALCHEMY_DEVBOARD
+ tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
+ depends on SOC_AU1X00 && PCMCIA
+ select 64BIT_PHYS_ADDR
+ help
+ Enable this driver of you want PCMCIA support on your Alchemy
+ Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200 board.
+ NOT suitable for the PB1000!
+
+ This driver is also available as a module called db1xxx_ss.ko
+
+config PCMCIA_XXS1500
+ tristate "MyCable XXS1500 PCMCIA socket support"
+ depends on PCMCIA && MIPS_XXS1500
+ select 64BIT_PHYS_ADDR
+ help
+ Support for the PCMCIA/CF socket interface on MyCable XXS1500
+ systems.
+
+ This driver is also available as a module called xxs1500_ss.ko
+
config PCMCIA_BCM63XX
tristate "bcm63xx pcmcia support"
depends on BCM63XX && PCMCIA
diff --git a/drivers/pcmcia/Makefile b/drivers/pcmcia/Makefile
index 3c83f68c803a..381b031d9d75 100644
--- a/drivers/pcmcia/Makefile
+++ b/drivers/pcmcia/Makefile
@@ -35,18 +35,10 @@ obj-$(CONFIG_OMAP_CF) += omap_cf.o
obj-$(CONFIG_BFIN_CFPCMCIA) += bfin_cf_pcmcia.o
obj-$(CONFIG_AT91_CF) += at91_cf.o
obj-$(CONFIG_ELECTRA_CF) += electra_cf.o
+obj-$(CONFIG_PCMCIA_ALCHEMY_DEVBOARD) += db1xxx_ss.o
au1x00_ss-y += au1000_generic.o
au1x00_ss-$(CONFIG_MIPS_PB1000) += au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_PB1100) += au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_PB1200) += au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_PB1500) += au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1000) += au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1100) += au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1200) += au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1500) += au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1550) += au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_XXS1500) += au1000_xxs1500.o
sa1111_cs-y += sa1111_generic.o
sa1111_cs-$(CONFIG_ASSABET_NEPONSET) += sa1100_neponset.o
@@ -76,3 +68,5 @@ pxa2xx-obj-$(CONFIG_MACH_E740) += pxa2xx_e740.o
pxa2xx-obj-$(CONFIG_MACH_STARGATE2) += pxa2xx_stargate2.o
obj-$(CONFIG_PCMCIA_PXA2XX) += pxa2xx_base.o $(pxa2xx-obj-y)
+
+obj-$(CONFIG_PCMCIA_XXS1500) += xxs1500_ss.o
diff --git a/drivers/pcmcia/au1000_db1x00.c b/drivers/pcmcia/au1000_db1x00.c
deleted file mode 100644
index c78d77fd7e3b..000000000000
--- a/drivers/pcmcia/au1000_db1x00.c
+++ /dev/null
@@ -1,305 +0,0 @@
-/*
- *
- * Alchemy Semi Db1x00 boards specific pcmcia routines.
- *
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * Copyright 2004 Pete Popov, updated the driver to 2.6.
- * Followed the sa11xx API and largely copied many of the hardware
- * independent functions.
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/init.h>
-
-#include <asm/irq.h>
-#include <asm/signal.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#if defined(CONFIG_MIPS_DB1200)
- #include <db1200.h>
-#elif defined(CONFIG_MIPS_PB1200)
- #include <pb1200.h>
-#else
- #include <asm/mach-db1x00/db1x00.h>
- static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-#endif
-
-#include "au1000_generic.h"
-
-#if 0
-#define debug(x,args...) printk(KERN_DEBUG "%s: " x, __func__ , ##args)
-#else
-#define debug(x,args...)
-#endif
-
-
-struct au1000_pcmcia_socket au1000_pcmcia_socket[PCMCIA_NUM_SOCKS];
-extern int au1x00_pcmcia_socket_probe(struct device *, struct pcmcia_low_level *, int, int);
-
-static int db1x00_pcmcia_hw_init(struct au1000_pcmcia_socket *skt)
-{
-#ifdef CONFIG_MIPS_DB1550
- skt->irq = skt->nr ? AU1000_GPIO_5 : AU1000_GPIO_3;
-#elif defined(CONFIG_MIPS_DB1200) || defined(CONFIG_MIPS_PB1200)
- skt->irq = skt->nr ? BOARD_PC1_INT : BOARD_PC0_INT;
-#else
- skt->irq = skt->nr ? AU1000_GPIO_5 : AU1000_GPIO_2;
-#endif
- return 0;
-}
-
-static void db1x00_pcmcia_shutdown(struct au1000_pcmcia_socket *skt)
-{
- bcsr->pcmcia = 0; /* turn off power */
- au_sync_delay(2);
-}
-
-static void
-db1x00_pcmcia_socket_state(struct au1000_pcmcia_socket *skt, struct pcmcia_state *state)
-{
- u32 inserted;
- unsigned char vs;
-
- state->ready = 0;
- state->vs_Xv = 0;
- state->vs_3v = 0;
- state->detect = 0;
-
- switch (skt->nr) {
- case 0:
- vs = bcsr->status & 0x3;
-#if defined(CONFIG_MIPS_DB1200) || defined(CONFIG_MIPS_PB1200)
- inserted = BOARD_CARD_INSERTED(0);
-#else
- inserted = !(bcsr->status & (1<<4));
-#endif
- break;
- case 1:
- vs = (bcsr->status & 0xC)>>2;
-#if defined(CONFIG_MIPS_DB1200) || defined(CONFIG_MIPS_PB1200)
- inserted = BOARD_CARD_INSERTED(1);
-#else
- inserted = !(bcsr->status & (1<<5));
-#endif
- break;
- default:/* should never happen */
- return;
- }
-
- if (inserted)
- debug("db1x00 socket %d: inserted %d, vs %d pcmcia %x\n",
- skt->nr, inserted, vs, bcsr->pcmcia);
-
- if (inserted) {
- switch (vs) {
- case 0:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- break;
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "db1x00 bad VS (%d)\n",
- vs);
- }
- state->detect = 1;
- state->ready = 1;
- }
- else {
- /* if the card was previously inserted and then ejected,
- * we should turn off power to it
- */
- if ((skt->nr == 0) && (bcsr->pcmcia & BCSR_PCMCIA_PC0RST)) {
- bcsr->pcmcia &= ~(BCSR_PCMCIA_PC0RST |
- BCSR_PCMCIA_PC0DRVEN |
- BCSR_PCMCIA_PC0VPP |
- BCSR_PCMCIA_PC0VCC);
- au_sync_delay(10);
- }
- else if ((skt->nr == 1) && bcsr->pcmcia & BCSR_PCMCIA_PC1RST) {
- bcsr->pcmcia &= ~(BCSR_PCMCIA_PC1RST |
- BCSR_PCMCIA_PC1DRVEN |
- BCSR_PCMCIA_PC1VPP |
- BCSR_PCMCIA_PC1VCC);
- au_sync_delay(10);
- }
- }
-
- state->bvd1=1;
- state->bvd2=1;
- state->wrprot=0;
-}
-
-static int
-db1x00_pcmcia_configure_socket(struct au1000_pcmcia_socket *skt, struct socket_state_t *state)
-{
- u16 pwr;
- int sock = skt->nr;
-
- debug("config_skt %d Vcc %dV Vpp %dV, reset %d\n",
- sock, state->Vcc, state->Vpp,
- state->flags & SS_RESET);
-
- /* pcmcia reg was set to zero at init time. Be careful when
- * initializing a socket not to wipe out the settings of the
- * other socket.
- */
- pwr = bcsr->pcmcia;
- pwr &= ~(0xf << sock*8); /* clear voltage settings */
-
- state->Vpp = 0;
- switch(state->Vcc){
- case 0: /* Vcc 0 */
- pwr |= SET_VCC_VPP(0,0,sock);
- break;
- case 50: /* Vcc 5V */
- switch(state->Vpp) {
- case 0:
- pwr |= SET_VCC_VPP(2,0,sock);
- break;
- case 50:
- pwr |= SET_VCC_VPP(2,1,sock);
- break;
- case 12:
- pwr |= SET_VCC_VPP(2,2,sock);
- break;
- case 33:
- default:
- pwr |= SET_VCC_VPP(0,0,sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- state->Vcc,
- state->Vpp);
- break;
- }
- break;
- case 33: /* Vcc 3.3V */
- switch(state->Vpp) {
- case 0:
- pwr |= SET_VCC_VPP(1,0,sock);
- break;
- case 12:
- pwr |= SET_VCC_VPP(1,2,sock);
- break;
- case 33:
- pwr |= SET_VCC_VPP(1,1,sock);
- break;
- case 50:
- default:
- pwr |= SET_VCC_VPP(0,0,sock);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- state->Vcc,
- state->Vpp);
- break;
- }
- break;
- default: /* what's this ? */
- pwr |= SET_VCC_VPP(0,0,sock);
- printk(KERN_ERR "%s: bad Vcc %d\n",
- __func__, state->Vcc);
- break;
- }
-
- bcsr->pcmcia = pwr;
- au_sync_delay(300);
-
- if (sock == 0) {
- if (!(state->flags & SS_RESET)) {
- pwr |= BCSR_PCMCIA_PC0DRVEN;
- bcsr->pcmcia = pwr;
- au_sync_delay(300);
- pwr |= BCSR_PCMCIA_PC0RST;
- bcsr->pcmcia = pwr;
- au_sync_delay(100);
- }
- else {
- pwr &= ~(BCSR_PCMCIA_PC0RST | BCSR_PCMCIA_PC0DRVEN);
- bcsr->pcmcia = pwr;
- au_sync_delay(100);
- }
- }
- else {
- if (!(state->flags & SS_RESET)) {
- pwr |= BCSR_PCMCIA_PC1DRVEN;
- bcsr->pcmcia = pwr;
- au_sync_delay(300);
- pwr |= BCSR_PCMCIA_PC1RST;
- bcsr->pcmcia = pwr;
- au_sync_delay(100);
- }
- else {
- pwr &= ~(BCSR_PCMCIA_PC1RST | BCSR_PCMCIA_PC1DRVEN);
- bcsr->pcmcia = pwr;
- au_sync_delay(100);
- }
- }
- return 0;
-}
-
-/*
- * Enable card status IRQs on (re-)initialisation. This can
- * be called at initialisation, power management event, or
- * pcmcia event.
- */
-void db1x00_socket_init(struct au1000_pcmcia_socket *skt)
-{
- /* nothing to do for now */
-}
-
-/*
- * Disable card status IRQs and PCMCIA bus on suspend.
- */
-void db1x00_socket_suspend(struct au1000_pcmcia_socket *skt)
-{
- /* nothing to do for now */
-}
-
-struct pcmcia_low_level db1x00_pcmcia_ops = {
- .owner = THIS_MODULE,
-
- .hw_init = db1x00_pcmcia_hw_init,
- .hw_shutdown = db1x00_pcmcia_shutdown,
-
- .socket_state = db1x00_pcmcia_socket_state,
- .configure_socket = db1x00_pcmcia_configure_socket,
-
- .socket_init = db1x00_socket_init,
- .socket_suspend = db1x00_socket_suspend
-};
-
-int au1x_board_init(struct device *dev)
-{
- int ret = -ENODEV;
- bcsr->pcmcia = 0; /* turn off power, if it's not already off */
- au_sync_delay(2);
- ret = au1x00_pcmcia_socket_probe(dev, &db1x00_pcmcia_ops, 0, 2);
- return ret;
-}
diff --git a/drivers/pcmcia/au1000_generic.c b/drivers/pcmcia/au1000_generic.c
index 02088704ac2c..171c8a654887 100644
--- a/drivers/pcmcia/au1000_generic.c
+++ b/drivers/pcmcia/au1000_generic.c
@@ -405,18 +405,16 @@ int au1x00_pcmcia_socket_probe(struct device *dev, struct pcmcia_low_level *ops,
skt->virt_io = (void *)
(ioremap((phys_t)AU1X_SOCK0_IO, 0x1000) -
(u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK0_PSEUDO_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK0_PSEUDO_PHYS_MEM;
+ skt->phys_attr = AU1X_SOCK0_PHYS_ATTR;
+ skt->phys_mem = AU1X_SOCK0_PHYS_MEM;
}
-#ifndef CONFIG_MIPS_XXS1500
else {
skt->virt_io = (void *)
(ioremap((phys_t)AU1X_SOCK1_IO, 0x1000) -
(u32)mips_io_port_base);
- skt->phys_attr = AU1X_SOCK1_PSEUDO_PHYS_ATTR;
- skt->phys_mem = AU1X_SOCK1_PSEUDO_PHYS_MEM;
+ skt->phys_attr = AU1X_SOCK1_PHYS_ATTR;
+ skt->phys_mem = AU1X_SOCK1_PHYS_MEM;
}
-#endif
pcmcia_base_vaddrs[i] = (u32 *)skt->virt_io;
ret = ops->hw_init(skt);
diff --git a/drivers/pcmcia/au1000_generic.h b/drivers/pcmcia/au1000_generic.h
index 13a4fbc58711..a324d329dea6 100644
--- a/drivers/pcmcia/au1000_generic.h
+++ b/drivers/pcmcia/au1000_generic.h
@@ -36,30 +36,14 @@
#define AU1X_SOCK0_IO 0xF00000000ULL
#define AU1X_SOCK0_PHYS_ATTR 0xF40000000ULL
#define AU1X_SOCK0_PHYS_MEM 0xF80000000ULL
-/* pseudo 32 bit phys addresses, which get fixed up to the
- * real 36 bit address in fixup_bigphys_addr() */
-#define AU1X_SOCK0_PSEUDO_PHYS_ATTR 0xF4000000
-#define AU1X_SOCK0_PSEUDO_PHYS_MEM 0xF8000000
/* pcmcia socket 1 needs external glue logic so the memory map
* differs from board to board.
*/
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_PB1100) || \
- defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_PB1550) || \
- defined(CONFIG_MIPS_PB1200)
+#if defined(CONFIG_MIPS_PB1000)
#define AU1X_SOCK1_IO 0xF08000000ULL
#define AU1X_SOCK1_PHYS_ATTR 0xF48000000ULL
#define AU1X_SOCK1_PHYS_MEM 0xF88000000ULL
-#define AU1X_SOCK1_PSEUDO_PHYS_ATTR 0xF4800000
-#define AU1X_SOCK1_PSEUDO_PHYS_MEM 0xF8800000
-#elif defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100) || \
- defined(CONFIG_MIPS_DB1500) || defined(CONFIG_MIPS_DB1550) || \
- defined(CONFIG_MIPS_DB1200)
-#define AU1X_SOCK1_IO 0xF04000000ULL
-#define AU1X_SOCK1_PHYS_ATTR 0xF44000000ULL
-#define AU1X_SOCK1_PHYS_MEM 0xF84000000ULL
-#define AU1X_SOCK1_PSEUDO_PHYS_ATTR 0xF4400000
-#define AU1X_SOCK1_PSEUDO_PHYS_MEM 0xF8400000
#endif
struct pcmcia_state {
diff --git a/drivers/pcmcia/au1000_pb1x00.c b/drivers/pcmcia/au1000_pb1x00.c
index b1984ed72d1d..5a979cb8f3e6 100644
--- a/drivers/pcmcia/au1000_pb1x00.c
+++ b/drivers/pcmcia/au1000_pb1x00.c
@@ -1,6 +1,6 @@
/*
*
- * Alchemy Semi Pb1x00 boards specific pcmcia routines.
+ * Alchemy Semi Pb1000 boards specific pcmcia routines.
*
* Copyright 2002 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
@@ -46,20 +46,11 @@
#define debug(fmt, arg...) do { } while (0)
-#ifdef CONFIG_MIPS_PB1000
#include <asm/pb1000.h>
#define PCMCIA_IRQ AU1000_GPIO_15
-#elif defined (CONFIG_MIPS_PB1500)
-#include <asm/pb1500.h>
-#define PCMCIA_IRQ AU1500_GPIO_203
-#elif defined (CONFIG_MIPS_PB1100)
-#include <asm/pb1100.h>
-#define PCMCIA_IRQ AU1000_GPIO_11
-#endif
static int pb1x00_pcmcia_init(struct pcmcia_init *init)
{
-#ifdef CONFIG_MIPS_PB1000
u16 pcr;
pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
@@ -74,21 +65,10 @@ static int pb1x00_pcmcia_init(struct pcmcia_init *init)
au_sync_delay(20);
return PCMCIA_NUM_SOCKS;
-
-#else /* fixme -- take care of the Pb1500 at some point */
-
- u16 pcr;
- pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
- pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
- au_writew(pcr, PCMCIA_BOARD_REG);
- au_sync_delay(500);
- return PCMCIA_NUM_SOCKS;
-#endif
}
static int pb1x00_pcmcia_shutdown(void)
{
-#ifdef CONFIG_MIPS_PB1000
u16 pcr;
pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
@@ -96,14 +76,6 @@ static int pb1x00_pcmcia_shutdown(void)
au_writel(pcr, PB1000_PCR);
au_sync_delay(20);
return 0;
-#else
- u16 pcr;
- pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
- pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
- au_writew(pcr, PCMCIA_BOARD_REG);
- au_sync_delay(2);
- return 0;
-#endif
}
static int
@@ -112,21 +84,11 @@ pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
u32 inserted0, inserted1;
u16 vs0, vs1;
-#ifdef CONFIG_MIPS_PB1000
vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
vs0 = (vs0 >> 4) & 0x3;
vs1 = (vs1 >> 12) & 0x3;
-#else
- vs0 = (au_readw(BOARD_STATUS_REG) >> 4) & 0x3;
-#ifdef CONFIG_MIPS_PB1500
- inserted0 = !((au_readl(GPIO2_PINSTATE) >> 1) & 0x1); /* gpio 201 */
-#else /* Pb1100 */
- inserted0 = !((au_readl(SYS_PINSTATERD) >> 9) & 0x1); /* gpio 9 */
-#endif
- inserted1 = 0;
-#endif
state->ready = 0;
state->vs_Xv = 0;
@@ -203,7 +165,6 @@ pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
if(configure->sock > PCMCIA_MAX_SOCK) return -1;
-#ifdef CONFIG_MIPS_PB1000
pcr = au_readl(PB1000_PCR);
if (configure->sock == 0) {
@@ -323,84 +284,6 @@ pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
au_writel(pcr, PB1000_PCR);
au_sync_delay(300);
-#else
-
- pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf;
-
- debug("Vcc %dV Vpp %dV, pcr %x, reset %d\n",
- configure->vcc, configure->vpp, pcr, configure->reset);
-
-
- switch(configure->vcc){
- case 0: /* Vcc 0 */
- pcr |= SET_VCC_VPP(0,0);
- break;
- case 50: /* Vcc 5V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(2,0);
- break;
- case 50:
- pcr |= SET_VCC_VPP(2,1);
- break;
- case 12:
- pcr |= SET_VCC_VPP(2,2);
- break;
- case 33:
- default:
- pcr |= SET_VCC_VPP(0,0);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- case 33: /* Vcc 3.3V */
- switch(configure->vpp) {
- case 0:
- pcr |= SET_VCC_VPP(1,0);
- break;
- case 12:
- pcr |= SET_VCC_VPP(1,2);
- break;
- case 33:
- pcr |= SET_VCC_VPP(1,1);
- break;
- case 50:
- default:
- pcr |= SET_VCC_VPP(0,0);
- printk("%s: bad Vcc/Vpp (%d:%d)\n",
- __func__,
- configure->vcc,
- configure->vpp);
- break;
- }
- break;
- default: /* what's this ? */
- pcr |= SET_VCC_VPP(0,0);
- printk(KERN_ERR "%s: bad Vcc %d\n",
- __func__, configure->vcc);
- break;
- }
-
- au_writew(pcr, PCMCIA_BOARD_REG);
- au_sync_delay(300);
-
- if (!configure->reset) {
- pcr |= PC_DRV_EN;
- au_writew(pcr, PCMCIA_BOARD_REG);
- au_sync_delay(100);
- pcr |= PC_DEASSERT_RST;
- au_writew(pcr, PCMCIA_BOARD_REG);
- au_sync_delay(100);
- }
- else {
- pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
- au_writew(pcr, PCMCIA_BOARD_REG);
- au_sync_delay(100);
- }
-#endif
return 0;
}
diff --git a/drivers/pcmcia/au1000_xxs1500.c b/drivers/pcmcia/au1000_xxs1500.c
deleted file mode 100644
index b43d47b50819..000000000000
--- a/drivers/pcmcia/au1000_xxs1500.c
+++ /dev/null
@@ -1,188 +0,0 @@
-/*
- *
- * MyCable board specific pcmcia routines.
- *
- * Copyright 2003 MontaVista Software Inc.
- * Author: Pete Popov, MontaVista Software, Inc.
- * ppopov@mvista.com or source@mvista.com
- *
- * ########################################################################
- *
- * This program is free software; you can distribute it and/or modify it
- * under the terms of the GNU General Public License (Version 2) as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope it will be useful, but WITHOUT
- * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
- * for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/ioport.h>
-#include <linux/kernel.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/proc_fs.h>
-#include <linux/types.h>
-
-#include <pcmcia/cs_types.h>
-#include <pcmcia/cs.h>
-#include <pcmcia/ss.h>
-#include <pcmcia/cistpl.h>
-#include <pcmcia/bus_ops.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <asm/system.h>
-
-#include <asm/au1000.h>
-#include <asm/au1000_pcmcia.h>
-
-#define PCMCIA_MAX_SOCK 0
-#define PCMCIA_NUM_SOCKS (PCMCIA_MAX_SOCK + 1)
-#define PCMCIA_IRQ AU1000_GPIO_4
-
-#if 0
-#define DEBUG(x, args...) printk(__func__ ": " x, ##args)
-#else
-#define DEBUG(x,args...)
-#endif
-
-static int xxs1500_pcmcia_init(struct pcmcia_init *init)
-{
- return PCMCIA_NUM_SOCKS;
-}
-
-static int xxs1500_pcmcia_shutdown(void)
-{
- /* turn off power */
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<14)|(1<<30),
- GPIO2_OUTPUT);
- au_sync_delay(100);
-
- /* assert reset */
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<4)|(1<<20),
- GPIO2_OUTPUT);
- au_sync_delay(100);
- return 0;
-}
-
-
-static int
-xxs1500_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
-{
- u32 inserted; u32 vs;
- unsigned long gpio, gpio2;
-
- if(sock > PCMCIA_MAX_SOCK) return -1;
-
- gpio = au_readl(SYS_PINSTATERD);
- gpio2 = au_readl(GPIO2_PINSTATE);
-
- vs = gpio2 & ((1<<8) | (1<<9));
- inserted = (!(gpio & 0x1) && !(gpio & 0x2));
-
- state->ready = 0;
- state->vs_Xv = 0;
- state->vs_3v = 0;
- state->detect = 0;
-
- if (inserted) {
- switch (vs) {
- case 0:
- case 1:
- case 2:
- state->vs_3v=1;
- break;
- case 3: /* 5V */
- default:
- /* return without setting 'detect' */
- printk(KERN_ERR "au1x00_cs: unsupported VS\n",
- vs);
- return;
- }
- state->detect = 1;
- }
-
- if (state->detect) {
- state->ready = 1;
- }
-
- state->bvd1= gpio2 & (1<<10);
- state->bvd2 = gpio2 & (1<<11);
- state->wrprot=0;
- return 1;
-}
-
-
-static int xxs1500_pcmcia_get_irq_info(struct pcmcia_irq_info *info)
-{
-
- if(info->sock > PCMCIA_MAX_SOCK) return -1;
- info->irq = PCMCIA_IRQ;
- return 0;
-}
-
-
-static int
-xxs1500_pcmcia_configure_socket(const struct pcmcia_configure *configure)
-{
-
- if(configure->sock > PCMCIA_MAX_SOCK) return -1;
-
- DEBUG("Vcc %dV Vpp %dV, reset %d\n",
- configure->vcc, configure->vpp, configure->reset);
-
- switch(configure->vcc){
- case 33: /* Vcc 3.3V */
- /* turn on power */
- DEBUG("turn on power\n");
- au_writel((au_readl(GPIO2_PINSTATE) & ~(1<<14))|(1<<30),
- GPIO2_OUTPUT);
- au_sync_delay(100);
- break;
- case 50: /* Vcc 5V */
- default: /* what's this ? */
- printk(KERN_ERR "au1x00_cs: unsupported VCC\n");
- case 0: /* Vcc 0 */
- /* turn off power */
- au_sync_delay(100);
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<14)|(1<<30),
- GPIO2_OUTPUT);
- break;
- }
-
- if (!configure->reset) {
- DEBUG("deassert reset\n");
- au_writel((au_readl(GPIO2_PINSTATE) & ~(1<<4))|(1<<20),
- GPIO2_OUTPUT);
- au_sync_delay(100);
- au_writel((au_readl(GPIO2_PINSTATE) & ~(1<<5))|(1<<21),
- GPIO2_OUTPUT);
- }
- else {
- DEBUG("assert reset\n");
- au_writel(au_readl(GPIO2_PINSTATE) | (1<<4)|(1<<20),
- GPIO2_OUTPUT);
- }
- au_sync_delay(100);
- return 0;
-}
-
-struct pcmcia_low_level xxs1500_pcmcia_ops = {
- xxs1500_pcmcia_init,
- xxs1500_pcmcia_shutdown,
- xxs1500_pcmcia_socket_state,
- xxs1500_pcmcia_get_irq_info,
- xxs1500_pcmcia_configure_socket
-};
diff --git a/drivers/pcmcia/db1xxx_ss.c b/drivers/pcmcia/db1xxx_ss.c
new file mode 100644
index 000000000000..3889cf07d6ce
--- /dev/null
+++ b/drivers/pcmcia/db1xxx_ss.c
@@ -0,0 +1,623 @@
+/*
+ * PCMCIA socket code for the Alchemy Db1xxx/Pb1xxx boards.
+ *
+ * Copyright (c) 2009 Manuel Lauss <manuel.lauss@gmail.com>
+ *
+ */
+
+/* This is a fairly generic PCMCIA socket driver suitable for the
+ * following Alchemy Development boards:
+ * Db1000, Db/Pb1500, Db/Pb1100, Db/Pb1550, Db/Pb1200.
+ *
+ * The Db1000 is used as a reference: Per-socket card-, carddetect- and
+ * statuschange IRQs connected to SoC GPIOs, control and status register
+ * bits arranged in per-socket groups in an external PLD. All boards
+ * listed here use this layout, including bit positions and meanings.
+ * Of course there are exceptions in later boards:
+ *
+ * - Pb1100/Pb1500: single socket only; voltage key bits VS are
+ * at STATUS[5:4] (instead of STATUS[1:0]).
+ * - Au1200-based: additional card-eject irqs, irqs not gpios!
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
+#include <linux/platform_device.h>
+#include <linux/resource.h>
+#include <linux/spinlock.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/ss.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#define MEM_MAP_SIZE 0x400000
+#define IO_MAP_SIZE 0x1000
+
+struct db1x_pcmcia_sock {
+ struct pcmcia_socket socket;
+ int nr; /* socket number */
+ void *virt_io;
+
+ /* the "pseudo" addresses of the PCMCIA space. */
+ phys_addr_t phys_io;
+ phys_addr_t phys_attr;
+ phys_addr_t phys_mem;
+
+ /* previous flags for set_socket() */
+ unsigned int old_flags;
+
+ /* interrupt sources: linux irq numbers! */
+ int insert_irq; /* default carddetect irq */
+ int stschg_irq; /* card-status-change irq */
+ int card_irq; /* card irq */
+ int eject_irq; /* db1200/pb1200 have these */
+
+#define BOARD_TYPE_DEFAULT 0 /* most boards */
+#define BOARD_TYPE_DB1200 1 /* IRQs aren't gpios */
+#define BOARD_TYPE_PB1100 2 /* VS bits slightly different */
+ int board_type;
+};
+
+#define to_db1x_socket(x) container_of(x, struct db1x_pcmcia_sock, socket)
+
+/* DB/PB1200: check CPLD SIGSTATUS register bit 10/12 */
+static int db1200_card_inserted(struct db1x_pcmcia_sock *sock)
+{
+ unsigned short sigstat;
+
+ sigstat = bcsr_read(BCSR_SIGSTAT);
+ return sigstat & 1 << (8 + 2 * sock->nr);
+}
+
+/* carddetect gpio: low-active */
+static int db1000_card_inserted(struct db1x_pcmcia_sock *sock)
+{
+ return !gpio_get_value(irq_to_gpio(sock->insert_irq));
+}
+
+static int db1x_card_inserted(struct db1x_pcmcia_sock *sock)
+{
+ switch (sock->board_type) {
+ case BOARD_TYPE_DB1200:
+ return db1200_card_inserted(sock);
+ default:
+ return db1000_card_inserted(sock);
+ }
+}
+
+/* STSCHG tends to bounce heavily when cards are inserted/ejected.
+ * To avoid this, the interrupt is normally disabled and only enabled
+ * after reset to a card has been de-asserted.
+ */
+static inline void set_stschg(struct db1x_pcmcia_sock *sock, int en)
+{
+ if (sock->stschg_irq != -1) {
+ if (en)
+ enable_irq(sock->stschg_irq);
+ else
+ disable_irq(sock->stschg_irq);
+ }
+}
+
+static irqreturn_t db1000_pcmcia_cdirq(int irq, void *data)
+{
+ struct db1x_pcmcia_sock *sock = data;
+
+ pcmcia_parse_events(&sock->socket, SS_DETECT);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t db1000_pcmcia_stschgirq(int irq, void *data)
+{
+ struct db1x_pcmcia_sock *sock = data;
+
+ pcmcia_parse_events(&sock->socket, SS_STSCHG);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t db1200_pcmcia_cdirq(int irq, void *data)
+{
+ struct db1x_pcmcia_sock *sock = data;
+
+ /* Db/Pb1200 have separate per-socket insertion and ejection
+ * interrupts which stay asserted as long as the card is
+ * inserted/missing. The one which caused us to be called
+ * needs to be disabled and the other one enabled.
+ */
+ if (irq == sock->insert_irq) {
+ disable_irq_nosync(sock->insert_irq);
+ enable_irq(sock->eject_irq);
+ } else {
+ disable_irq_nosync(sock->eject_irq);
+ enable_irq(sock->insert_irq);
+ }
+
+ pcmcia_parse_events(&sock->socket, SS_DETECT);
+
+ return IRQ_HANDLED;
+}
+
+static int db1x_pcmcia_setup_irqs(struct db1x_pcmcia_sock *sock)
+{
+ int ret;
+ unsigned long flags;
+
+ if (sock->stschg_irq != -1) {
+ ret = request_irq(sock->stschg_irq, db1000_pcmcia_stschgirq,
+ 0, "pcmcia_stschg", sock);
+ if (ret)
+ return ret;
+ }
+
+ /* Db/Pb1200 have separate per-socket insertion and ejection
+ * interrupts, which should show edge behaviour but don't.
+ * So interrupts are disabled until both insertion and
+ * ejection handler have been registered and the currently
+ * active one disabled.
+ */
+ if (sock->board_type == BOARD_TYPE_DB1200) {
+ local_irq_save(flags);
+
+ ret = request_irq(sock->insert_irq, db1200_pcmcia_cdirq,
+ IRQF_DISABLED, "pcmcia_insert", sock);
+ if (ret)
+ goto out1;
+
+ ret = request_irq(sock->eject_irq, db1200_pcmcia_cdirq,
+ IRQF_DISABLED, "pcmcia_eject", sock);
+ if (ret) {
+ free_irq(sock->insert_irq, sock);
+ local_irq_restore(flags);
+ goto out1;
+ }
+
+ /* disable the currently active one */
+ if (db1200_card_inserted(sock))
+ disable_irq_nosync(sock->insert_irq);
+ else
+ disable_irq_nosync(sock->eject_irq);
+
+ local_irq_restore(flags);
+ } else {
+ /* all other (older) Db1x00 boards use a GPIO to show
+ * card detection status: use both-edge triggers.
+ */
+ set_irq_type(sock->insert_irq, IRQ_TYPE_EDGE_BOTH);
+ ret = request_irq(sock->insert_irq, db1000_pcmcia_cdirq,
+ 0, "pcmcia_carddetect", sock);
+
+ if (ret)
+ goto out1;
+ }
+
+ return 0; /* all done */
+
+out1:
+ if (sock->stschg_irq != -1)
+ free_irq(sock->stschg_irq, sock);
+
+ return ret;
+}
+
+static void db1x_pcmcia_free_irqs(struct db1x_pcmcia_sock *sock)
+{
+ if (sock->stschg_irq != -1)
+ free_irq(sock->stschg_irq, sock);
+
+ free_irq(sock->insert_irq, sock);
+ if (sock->eject_irq != -1)
+ free_irq(sock->eject_irq, sock);
+}
+
+/*
+ * configure a PCMCIA socket on the Db1x00 series of boards (and
+ * compatibles).
+ *
+ * 2 external registers are involved:
+ * pcmcia_status (offset 0x04): bits [0:1/2:3]: read card voltage id
+ * pcmcia_control(offset 0x10):
+ * bits[0:1] set vcc for card
+ * bits[2:3] set vpp for card
+ * bit 4: enable data buffers
+ * bit 7: reset# for card
+ * add 8 for second socket.
+ */
+static int db1x_pcmcia_configure(struct pcmcia_socket *skt,
+ struct socket_state_t *state)
+{
+ struct db1x_pcmcia_sock *sock = to_db1x_socket(skt);
+ unsigned short cr_clr, cr_set;
+ unsigned int changed;
+ int v, p, ret;
+
+ /* card voltage setup */
+ cr_clr = (0xf << (sock->nr * 8)); /* clear voltage settings */
+ cr_set = 0;
+ v = p = ret = 0;
+
+ switch (state->Vcc) {
+ case 50:
+ ++v;
+ case 33:
+ ++v;
+ case 0:
+ break;
+ default:
+ printk(KERN_INFO "pcmcia%d unsupported Vcc %d\n",
+ sock->nr, state->Vcc);
+ }
+
+ switch (state->Vpp) {
+ case 12:
+ ++p;
+ case 33:
+ case 50:
+ ++p;
+ case 0:
+ break;
+ default:
+ printk(KERN_INFO "pcmcia%d unsupported Vpp %d\n",
+ sock->nr, state->Vpp);
+ }
+
+ /* sanity check: Vpp must be 0, 12, or Vcc */
+ if (((state->Vcc == 33) && (state->Vpp == 50)) ||
+ ((state->Vcc == 50) && (state->Vpp == 33))) {
+ printk(KERN_INFO "pcmcia%d bad Vcc/Vpp combo (%d %d)\n",
+ sock->nr, state->Vcc, state->Vpp);
+ v = p = 0;
+ ret = -EINVAL;
+ }
+
+ /* create new voltage code */
+ cr_set |= ((v << 2) | p) << (sock->nr * 8);
+
+ changed = state->flags ^ sock->old_flags;
+
+ if (changed & SS_RESET) {
+ if (state->flags & SS_RESET) {
+ set_stschg(sock, 0);
+ /* assert reset, disable io buffers */
+ cr_clr |= (1 << (7 + (sock->nr * 8)));
+ cr_clr |= (1 << (4 + (sock->nr * 8)));
+ } else {
+ /* de-assert reset, enable io buffers */
+ cr_set |= 1 << (7 + (sock->nr * 8));
+ cr_set |= 1 << (4 + (sock->nr * 8));
+ }
+ }
+
+ /* update PCMCIA configuration */
+ bcsr_mod(BCSR_PCMCIA, cr_clr, cr_set);
+
+ sock->old_flags = state->flags;
+
+ /* reset was taken away: give card time to initialize properly */
+ if ((changed & SS_RESET) && !(state->flags & SS_RESET)) {
+ msleep(500);
+ set_stschg(sock, 1);
+ }
+
+ return ret;
+}
+
+/* VCC bits at [3:2]/[11:10] */
+#define GET_VCC(cr, socknr) \
+ ((((cr) >> 2) >> ((socknr) * 8)) & 3)
+
+/* VS bits at [0:1]/[3:2] */
+#define GET_VS(sr, socknr) \
+ (((sr) >> (2 * (socknr))) & 3)
+
+/* reset bits at [7]/[15] */
+#define GET_RESET(cr, socknr) \
+ ((cr) & (1 << (7 + (8 * (socknr)))))
+
+static int db1x_pcmcia_get_status(struct pcmcia_socket *skt,
+ unsigned int *value)
+{
+ struct db1x_pcmcia_sock *sock = to_db1x_socket(skt);
+ unsigned short cr, sr;
+ unsigned int status;
+
+ status = db1x_card_inserted(sock) ? SS_DETECT : 0;
+
+ cr = bcsr_read(BCSR_PCMCIA);
+ sr = bcsr_read(BCSR_STATUS);
+
+ /* PB1100/PB1500: voltage key bits are at [5:4] */
+ if (sock->board_type == BOARD_TYPE_PB1100)
+ sr >>= 4;
+
+ /* determine card type */
+ switch (GET_VS(sr, sock->nr)) {
+ case 0:
+ case 2:
+ status |= SS_3VCARD; /* 3V card */
+ case 3:
+ break; /* 5V card: set nothing */
+ default:
+ status |= SS_XVCARD; /* treated as unsupported in core */
+ }
+
+ /* if Vcc is not zero, we have applied power to a card */
+ status |= GET_VCC(cr, sock->nr) ? SS_POWERON : 0;
+
+ /* reset de-asserted? then we're ready */
+ status |= (GET_RESET(cr, sock->nr)) ? SS_READY : SS_RESET;
+
+ *value = status;
+
+ return 0;
+}
+
+static int db1x_pcmcia_sock_init(struct pcmcia_socket *skt)
+{
+ return 0;
+}
+
+static int db1x_pcmcia_sock_suspend(struct pcmcia_socket *skt)
+{
+ return 0;
+}
+
+static int au1x00_pcmcia_set_io_map(struct pcmcia_socket *skt,
+ struct pccard_io_map *map)
+{
+ struct db1x_pcmcia_sock *sock = to_db1x_socket(skt);
+
+ map->start = (u32)sock->virt_io;
+ map->stop = map->start + IO_MAP_SIZE;
+
+ return 0;
+}
+
+static int au1x00_pcmcia_set_mem_map(struct pcmcia_socket *skt,
+ struct pccard_mem_map *map)
+{
+ struct db1x_pcmcia_sock *sock = to_db1x_socket(skt);
+
+ if (map->flags & MAP_ATTRIB)
+ map->static_start = sock->phys_attr + map->card_start;
+ else
+ map->static_start = sock->phys_mem + map->card_start;
+
+ return 0;
+}
+
+static struct pccard_operations db1x_pcmcia_operations = {
+ .init = db1x_pcmcia_sock_init,
+ .suspend = db1x_pcmcia_sock_suspend,
+ .get_status = db1x_pcmcia_get_status,
+ .set_socket = db1x_pcmcia_configure,
+ .set_io_map = au1x00_pcmcia_set_io_map,
+ .set_mem_map = au1x00_pcmcia_set_mem_map,
+};
+
+static int __devinit db1x_pcmcia_socket_probe(struct platform_device *pdev)
+{
+ struct db1x_pcmcia_sock *sock;
+ struct resource *r;
+ int ret, bid;
+
+ sock = kzalloc(sizeof(struct db1x_pcmcia_sock), GFP_KERNEL);
+ if (!sock)
+ return -ENOMEM;
+
+ sock->nr = pdev->id;
+
+ bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
+ switch (bid) {
+ case BCSR_WHOAMI_PB1500:
+ case BCSR_WHOAMI_PB1500R2:
+ case BCSR_WHOAMI_PB1100:
+ sock->board_type = BOARD_TYPE_PB1100;
+ break;
+ case BCSR_WHOAMI_DB1000 ... BCSR_WHOAMI_PB1550_SDR:
+ sock->board_type = BOARD_TYPE_DEFAULT;
+ break;
+ case BCSR_WHOAMI_PB1200 ... BCSR_WHOAMI_DB1200:
+ sock->board_type = BOARD_TYPE_DB1200;
+ break;
+ default:
+ printk(KERN_INFO "db1xxx-ss: unknown board %d!\n", bid);
+ ret = -ENODEV;
+ goto out0;
+ };
+
+ /*
+ * gather resources necessary and optional nice-to-haves to
+ * operate a socket:
+ * This includes IRQs for Carddetection/ejection, the card
+ * itself and optional status change detection.
+ * Also, the memory areas covered by a socket. For these
+ * we require the 32bit "pseudo" addresses (see the au1000.h
+ * header for more information).
+ */
+
+ /* card: irq assigned to the card itself. */
+ r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "card");
+ sock->card_irq = r ? r->start : 0;
+
+ /* insert: irq which triggers on card insertion/ejection */
+ r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "insert");
+ sock->insert_irq = r ? r->start : -1;
+
+ /* stschg: irq which trigger on card status change (optional) */
+ r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "stschg");
+ sock->stschg_irq = r ? r->start : -1;
+
+ /* eject: irq which triggers on ejection (DB1200/PB1200 only) */
+ r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, "eject");
+ sock->eject_irq = r ? r->start : -1;
+
+ ret = -ENODEV;
+
+ /*
+ * pseudo-attr: The 32bit address of the PCMCIA attribute space
+ * for this socket (usually the 36bit address shifted 4 to the
+ * right).
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-attr");
+ if (!r) {
+ printk(KERN_ERR "pcmcia%d has no 'pseudo-attr' resource!\n",
+ sock->nr);
+ goto out0;
+ }
+ sock->phys_attr = r->start;
+
+ /*
+ * pseudo-mem: The 32bit address of the PCMCIA memory space for
+ * this socket (usually the 36bit address shifted 4 to the right)
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-mem");
+ if (!r) {
+ printk(KERN_ERR "pcmcia%d has no 'pseudo-mem' resource!\n",
+ sock->nr);
+ goto out0;
+ }
+ sock->phys_mem = r->start;
+
+ /*
+ * pseudo-io: The 32bit address of the PCMCIA IO space for this
+ * socket (usually the 36bit address shifted 4 to the right).
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-io");
+ if (!r) {
+ printk(KERN_ERR "pcmcia%d has no 'pseudo-io' resource!\n",
+ sock->nr);
+ goto out0;
+ }
+ sock->phys_io = r->start;
+
+ /*
+ * PCMCIA client drivers use the inb/outb macros to access
+ * the IO registers. Since mips_io_port_base is added
+ * to the access address of the mips implementation of
+ * inb/outb, we need to subtract it here because we want
+ * to access the I/O or MEM address directly, without
+ * going through this "mips_io_port_base" mechanism.
+ */
+ sock->virt_io = (void *)(ioremap(sock->phys_io, IO_MAP_SIZE) -
+ mips_io_port_base);
+
+ if (!sock->virt_io) {
+ printk(KERN_ERR "pcmcia%d: cannot remap IO area\n",
+ sock->nr);
+ ret = -ENOMEM;
+ goto out0;
+ }
+
+ sock->socket.ops = &db1x_pcmcia_operations;
+ sock->socket.owner = THIS_MODULE;
+ sock->socket.pci_irq = sock->card_irq;
+ sock->socket.features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
+ sock->socket.map_size = MEM_MAP_SIZE;
+ sock->socket.io_offset = (unsigned long)sock->virt_io;
+ sock->socket.dev.parent = &pdev->dev;
+ sock->socket.resource_ops = &pccard_static_ops;
+
+ platform_set_drvdata(pdev, sock);
+
+ ret = db1x_pcmcia_setup_irqs(sock);
+ if (ret) {
+ printk(KERN_ERR "pcmcia%d cannot setup interrupts\n",
+ sock->nr);
+ goto out1;
+ }
+
+ set_stschg(sock, 0);
+
+ ret = pcmcia_register_socket(&sock->socket);
+ if (ret) {
+ printk(KERN_ERR "pcmcia%d failed to register\n", sock->nr);
+ goto out2;
+ }
+
+ printk(KERN_INFO "Alchemy Db/Pb1xxx pcmcia%d @ io/attr/mem %09llx"
+ "(%p) %09llx %09llx card/insert/stschg/eject irqs @ %d "
+ "%d %d %d\n", sock->nr, sock->phys_io, sock->virt_io,
+ sock->phys_attr, sock->phys_mem, sock->card_irq,
+ sock->insert_irq, sock->stschg_irq, sock->eject_irq);
+
+ return 0;
+
+out2:
+ db1x_pcmcia_free_irqs(sock);
+out1:
+ iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
+out0:
+ kfree(sock);
+ return ret;
+}
+
+static int __devexit db1x_pcmcia_socket_remove(struct platform_device *pdev)
+{
+ struct db1x_pcmcia_sock *sock = platform_get_drvdata(pdev);
+
+ db1x_pcmcia_free_irqs(sock);
+ pcmcia_unregister_socket(&sock->socket);
+ iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
+ kfree(sock);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int db1x_pcmcia_suspend(struct device *dev)
+{
+ return pcmcia_socket_dev_suspend(dev);
+}
+
+static int db1x_pcmcia_resume(struct device *dev)
+{
+ return pcmcia_socket_dev_resume(dev);
+}
+
+static struct dev_pm_ops db1x_pcmcia_pmops = {
+ .resume = db1x_pcmcia_resume,
+ .suspend = db1x_pcmcia_suspend,
+ .thaw = db1x_pcmcia_resume,
+ .freeze = db1x_pcmcia_suspend,
+};
+
+#define DB1XXX_SS_PMOPS &db1x_pcmcia_pmops
+
+#else
+
+#define DB1XXX_SS_PMOPS NULL
+
+#endif
+
+static struct platform_driver db1x_pcmcia_socket_driver = {
+ .driver = {
+ .name = "db1xxx_pcmcia",
+ .owner = THIS_MODULE,
+ .pm = DB1XXX_SS_PMOPS
+ },
+ .probe = db1x_pcmcia_socket_probe,
+ .remove = __devexit_p(db1x_pcmcia_socket_remove),
+};
+
+int __init db1x_pcmcia_socket_load(void)
+{
+ return platform_driver_register(&db1x_pcmcia_socket_driver);
+}
+
+void __exit db1x_pcmcia_socket_unload(void)
+{
+ platform_driver_unregister(&db1x_pcmcia_socket_driver);
+}
+
+module_init(db1x_pcmcia_socket_load);
+module_exit(db1x_pcmcia_socket_unload);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("PCMCIA Socket Services for Alchemy Db/Pb1x00 boards");
+MODULE_AUTHOR("Manuel Lauss");
diff --git a/drivers/pcmcia/xxs1500_ss.c b/drivers/pcmcia/xxs1500_ss.c
new file mode 100644
index 000000000000..61560cd6e287
--- /dev/null
+++ b/drivers/pcmcia/xxs1500_ss.c
@@ -0,0 +1,350 @@
+/*
+ * PCMCIA socket code for the MyCable XXS1500 system.
+ *
+ * Copyright (c) 2009 Manuel Lauss <manuel.lauss@gmail.com>
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/mm.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/resource.h>
+#include <linux/spinlock.h>
+
+#include <pcmcia/cs_types.h>
+#include <pcmcia/cs.h>
+#include <pcmcia/ss.h>
+#include <pcmcia/cistpl.h>
+
+#include <asm/irq.h>
+#include <asm/system.h>
+#include <asm/mach-au1x00/au1000.h>
+
+#define MEM_MAP_SIZE 0x400000
+#define IO_MAP_SIZE 0x1000
+
+
+/*
+ * 3.3V cards only; all interfacing is done via gpios:
+ *
+ * 0/1: carddetect (00 = card present, xx = huh)
+ * 4: card irq
+ * 204: reset (high-act)
+ * 205: buffer enable (low-act)
+ * 208/209: card voltage key (00,01,10,11)
+ * 210: battwarn
+ * 211: batdead
+ * 214: power (low-act)
+ */
+#define GPIO_CDA 0
+#define GPIO_CDB 1
+#define GPIO_CARDIRQ 4
+#define GPIO_RESET 204
+#define GPIO_OUTEN 205
+#define GPIO_VSL 208
+#define GPIO_VSH 209
+#define GPIO_BATTDEAD 210
+#define GPIO_BATTWARN 211
+#define GPIO_POWER 214
+
+struct xxs1500_pcmcia_sock {
+ struct pcmcia_socket socket;
+ void *virt_io;
+
+ phys_addr_t phys_io;
+ phys_addr_t phys_attr;
+ phys_addr_t phys_mem;
+
+ /* previous flags for set_socket() */
+ unsigned int old_flags;
+};
+
+#define to_xxs_socket(x) container_of(x, struct xxs1500_pcmcia_sock, socket)
+
+static irqreturn_t cdirq(int irq, void *data)
+{
+ struct xxs1500_pcmcia_sock *sock = data;
+
+ pcmcia_parse_events(&sock->socket, SS_DETECT);
+
+ return IRQ_HANDLED;
+}
+
+static int xxs1500_pcmcia_configure(struct pcmcia_socket *skt,
+ struct socket_state_t *state)
+{
+ struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
+ unsigned int changed;
+
+ /* power control */
+ switch (state->Vcc) {
+ case 0:
+ gpio_set_value(GPIO_POWER, 1); /* power off */
+ break;
+ case 33:
+ gpio_set_value(GPIO_POWER, 0); /* power on */
+ break;
+ case 50:
+ default:
+ return -EINVAL;
+ }
+
+ changed = state->flags ^ sock->old_flags;
+
+ if (changed & SS_RESET) {
+ if (state->flags & SS_RESET) {
+ gpio_set_value(GPIO_RESET, 1); /* assert reset */
+ gpio_set_value(GPIO_OUTEN, 1); /* buffers off */
+ } else {
+ gpio_set_value(GPIO_RESET, 0); /* deassert reset */
+ gpio_set_value(GPIO_OUTEN, 0); /* buffers on */
+ msleep(500);
+ }
+ }
+
+ sock->old_flags = state->flags;
+
+ return 0;
+}
+
+static int xxs1500_pcmcia_get_status(struct pcmcia_socket *skt,
+ unsigned int *value)
+{
+ unsigned int status;
+ int i;
+
+ status = 0;
+
+ /* check carddetects: GPIO[0:1] must both be low */
+ if (!gpio_get_value(GPIO_CDA) && !gpio_get_value(GPIO_CDB))
+ status |= SS_DETECT;
+
+ /* determine card voltage: GPIO[208:209] binary value */
+ i = (!!gpio_get_value(GPIO_VSL)) | ((!!gpio_get_value(GPIO_VSH)) << 1);
+
+ switch (i) {
+ case 0:
+ case 1:
+ case 2:
+ status |= SS_3VCARD; /* 3V card */
+ break;
+ case 3: /* 5V card, unsupported */
+ default:
+ status |= SS_XVCARD; /* treated as unsupported in core */
+ }
+
+ /* GPIO214: low active power switch */
+ status |= gpio_get_value(GPIO_POWER) ? 0 : SS_POWERON;
+
+ /* GPIO204: high-active reset line */
+ status |= gpio_get_value(GPIO_RESET) ? SS_RESET : SS_READY;
+
+ /* other stuff */
+ status |= gpio_get_value(GPIO_BATTDEAD) ? 0 : SS_BATDEAD;
+ status |= gpio_get_value(GPIO_BATTWARN) ? 0 : SS_BATWARN;
+
+ *value = status;
+
+ return 0;
+}
+
+static int xxs1500_pcmcia_sock_init(struct pcmcia_socket *skt)
+{
+ gpio_direction_input(GPIO_CDA);
+ gpio_direction_input(GPIO_CDB);
+ gpio_direction_input(GPIO_VSL);
+ gpio_direction_input(GPIO_VSH);
+ gpio_direction_input(GPIO_BATTDEAD);
+ gpio_direction_input(GPIO_BATTWARN);
+ gpio_direction_output(GPIO_RESET, 1); /* assert reset */
+ gpio_direction_output(GPIO_OUTEN, 1); /* disable buffers */
+ gpio_direction_output(GPIO_POWER, 1); /* power off */
+
+ return 0;
+}
+
+static int xxs1500_pcmcia_sock_suspend(struct pcmcia_socket *skt)
+{
+ return 0;
+}
+
+static int au1x00_pcmcia_set_io_map(struct pcmcia_socket *skt,
+ struct pccard_io_map *map)
+{
+ struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
+
+ map->start = (u32)sock->virt_io;
+ map->stop = map->start + IO_MAP_SIZE;
+
+ return 0;
+}
+
+static int au1x00_pcmcia_set_mem_map(struct pcmcia_socket *skt,
+ struct pccard_mem_map *map)
+{
+ struct xxs1500_pcmcia_sock *sock = to_xxs_socket(skt);
+
+ if (map->flags & MAP_ATTRIB)
+ map->static_start = sock->phys_attr + map->card_start;
+ else
+ map->static_start = sock->phys_mem + map->card_start;
+
+ return 0;
+}
+
+static struct pccard_operations xxs1500_pcmcia_operations = {
+ .init = xxs1500_pcmcia_sock_init,
+ .suspend = xxs1500_pcmcia_sock_suspend,
+ .get_status = xxs1500_pcmcia_get_status,
+ .set_socket = xxs1500_pcmcia_configure,
+ .set_io_map = au1x00_pcmcia_set_io_map,
+ .set_mem_map = au1x00_pcmcia_set_mem_map,
+};
+
+static int __devinit xxs1500_pcmcia_probe(struct platform_device *pdev)
+{
+ struct xxs1500_pcmcia_sock *sock;
+ struct resource *r;
+ int ret, irq;
+
+ sock = kzalloc(sizeof(struct xxs1500_pcmcia_sock), GFP_KERNEL);
+ if (!sock)
+ return -ENOMEM;
+
+ ret = -ENODEV;
+
+ /*
+ * pseudo-attr: The 32bit address of the PCMCIA attribute space
+ * for this socket (usually the 36bit address shifted 4 to the
+ * right).
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-attr");
+ if (!r) {
+ dev_err(&pdev->dev, "missing 'pcmcia-attr' resource!\n");
+ goto out0;
+ }
+ sock->phys_attr = r->start;
+
+ /*
+ * pseudo-mem: The 32bit address of the PCMCIA memory space for
+ * this socket (usually the 36bit address shifted 4 to the right)
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-mem");
+ if (!r) {
+ dev_err(&pdev->dev, "missing 'pcmcia-mem' resource!\n");
+ goto out0;
+ }
+ sock->phys_mem = r->start;
+
+ /*
+ * pseudo-io: The 32bit address of the PCMCIA IO space for this
+ * socket (usually the 36bit address shifted 4 to the right).
+ */
+ r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pcmcia-io");
+ if (!r) {
+ dev_err(&pdev->dev, "missing 'pcmcia-io' resource!\n");
+ goto out0;
+ }
+ sock->phys_io = r->start;
+
+
+ /*
+ * PCMCIA client drivers use the inb/outb macros to access
+ * the IO registers. Since mips_io_port_base is added
+ * to the access address of the mips implementation of
+ * inb/outb, we need to subtract it here because we want
+ * to access the I/O or MEM address directly, without
+ * going through this "mips_io_port_base" mechanism.
+ */
+ sock->virt_io = (void *)(ioremap(sock->phys_io, IO_MAP_SIZE) -
+ mips_io_port_base);
+
+ if (!sock->virt_io) {
+ dev_err(&pdev->dev, "cannot remap IO area\n");
+ ret = -ENOMEM;
+ goto out0;
+ }
+
+ sock->socket.ops = &xxs1500_pcmcia_operations;
+ sock->socket.owner = THIS_MODULE;
+ sock->socket.pci_irq = gpio_to_irq(GPIO_CARDIRQ);
+ sock->socket.features = SS_CAP_STATIC_MAP | SS_CAP_PCCARD;
+ sock->socket.map_size = MEM_MAP_SIZE;
+ sock->socket.io_offset = (unsigned long)sock->virt_io;
+ sock->socket.dev.parent = &pdev->dev;
+ sock->socket.resource_ops = &pccard_static_ops;
+
+ platform_set_drvdata(pdev, sock);
+
+ /* setup carddetect irq: use one of the 2 GPIOs as an
+ * edge detector.
+ */
+ irq = gpio_to_irq(GPIO_CDA);
+ set_irq_type(irq, IRQ_TYPE_EDGE_BOTH);
+ ret = request_irq(irq, cdirq, 0, "pcmcia_carddetect", sock);
+ if (ret) {
+ dev_err(&pdev->dev, "cannot setup cd irq\n");
+ goto out1;
+ }
+
+ ret = pcmcia_register_socket(&sock->socket);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register\n");
+ goto out2;
+ }
+
+ printk(KERN_INFO "MyCable XXS1500 PCMCIA socket services\n");
+
+ return 0;
+
+out2:
+ free_irq(gpio_to_irq(GPIO_CDA), sock);
+out1:
+ iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
+out0:
+ kfree(sock);
+ return ret;
+}
+
+static int __devexit xxs1500_pcmcia_remove(struct platform_device *pdev)
+{
+ struct xxs1500_pcmcia_sock *sock = platform_get_drvdata(pdev);
+
+ pcmcia_unregister_socket(&sock->socket);
+ free_irq(gpio_to_irq(GPIO_CDA), sock);
+ iounmap((void *)(sock->virt_io + (u32)mips_io_port_base));
+ kfree(sock);
+
+ return 0;
+}
+
+static struct platform_driver xxs1500_pcmcia_socket_driver = {
+ .driver = {
+ .name = "xxs1500_pcmcia",
+ .owner = THIS_MODULE,
+ },
+ .probe = xxs1500_pcmcia_probe,
+ .remove = __devexit_p(xxs1500_pcmcia_remove),
+};
+
+int __init xxs1500_pcmcia_socket_load(void)
+{
+ return platform_driver_register(&xxs1500_pcmcia_socket_driver);
+}
+
+void __exit xxs1500_pcmcia_socket_unload(void)
+{
+ platform_driver_unregister(&xxs1500_pcmcia_socket_driver);
+}
+
+module_init(xxs1500_pcmcia_socket_load);
+module_exit(xxs1500_pcmcia_socket_unload);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("PCMCIA Socket Services for MyCable XXS1500 systems");
+MODULE_AUTHOR("Manuel Lauss");