diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-csr.h')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-csr.h | 181 |
1 files changed, 152 insertions, 29 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-csr.h b/drivers/net/wireless/iwlwifi/iwl-csr.h index b6ed5a3147a1..a7bfae01f19b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-csr.h +++ b/drivers/net/wireless/iwlwifi/iwl-csr.h @@ -62,11 +62,29 @@ *****************************************************************************/ #ifndef __iwl_csr_h__ #define __iwl_csr_h__ -/*=== CSR (control and status registers) ===*/ +/* + * CSR (control and status registers) + * + * CSR registers are mapped directly into PCI bus space, and are accessible + * whenever platform supplies power to device, even when device is in + * low power states due to driver-invoked device resets + * (e.g. CSR_RESET_REG_FLAG_SW_RESET) or uCode-driven power-saving modes. + * + * Use iwl_write32() and iwl_read32() family to access these registers; + * these provide simple PCI bus access, without waking up the MAC. + * Do not use iwl_write_direct32() family for these registers; + * no need to "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ. + * The MAC (uCode processor, etc.) does not need to be powered up for accessing + * the CSR registers. + * + * NOTE: Newer devices using one-time-programmable (OTP) memory + * require device to be awake in order to read this memory + * via CSR_EEPROM and CSR_OTP registers + */ #define CSR_BASE (0x000) #define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ -#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ +#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ #define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ #define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ #define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ @@ -74,42 +92,65 @@ #define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ #define CSR_GP_CNTRL (CSR_BASE+0x024) +/* 2nd byte of CSR_INT_COALESCING, not accessible via iwl_write32()! */ +#define CSR_INT_PERIODIC_REG (CSR_BASE+0x005) + /* * Hardware revision info * Bit fields: * 31-8: Reserved - * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 + * 7-4: Type of device: see CSR_HW_REV_TYPE_xxx definitions * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D - * 1-0: "Dash" value, as in A-1, etc. + * 1-0: "Dash" (-) value, as in A-1, etc. * * NOTE: Revision step affects calculation of CCK txpower for 4965. + * NOTE: See also CSR_HW_REV_WA_REG (work-around for bug in 4965). */ #define CSR_HW_REV (CSR_BASE+0x028) -/* EEPROM reads */ +/* + * EEPROM and OTP (one-time-programmable) memory reads + * + * NOTE: For (newer) devices using OTP, device must be awake, initialized via + * apm_ops.init() in order to read. Older devices (3945/4965/5000) + * use EEPROM and do not require this. + */ #define CSR_EEPROM_REG (CSR_BASE+0x02c) #define CSR_EEPROM_GP (CSR_BASE+0x030) #define CSR_OTP_GP_REG (CSR_BASE+0x034) + #define CSR_GIO_REG (CSR_BASE+0x03C) #define CSR_GP_UCODE_REG (CSR_BASE+0x048) #define CSR_GP_DRIVER_REG (CSR_BASE+0x050) + +/* + * UCODE-DRIVER GP (general purpose) mailbox registers. + * SET/CLR registers set/clear bit(s) if "1" is written. + */ #define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) #define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) #define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) #define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) + #define CSR_LED_REG (CSR_BASE+0x094) #define CSR_DRAM_INT_TBL_REG (CSR_BASE+0x0A0) + +/* GIO Chicken Bits (PCI Express bus link power management) */ #define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) -#define CSR_INT_PERIODIC_REG (CSR_BASE+0x005) /* Analog phase-lock-loop configuration */ #define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) + /* - * Indicates hardware rev, to determine CCK backoff for txpower calculation. + * CSR Hardware Revision Workaround Register. Indicates hardware rev; + * "step" determines CCK backoff for txpower calculation. Used for 4965 only. + * See also CSR_HW_REV register. * Bit fields: * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step + * 1-0: "Dash" (-) value, as in C-1, etc. */ #define CSR_HW_REV_WA_REG (CSR_BASE+0x22C) + #define CSR_DBG_HPET_MEM_REG (CSR_BASE+0x240) #define CSR_DBG_LINK_PWR_MGMT_REG (CSR_BASE+0x250) @@ -126,14 +167,14 @@ #define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000) #define CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000) -#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000) -#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) -#define CSR_HW_IF_CONFIG_REG_BIT_NIC_READY (0x00400000) -#define CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE (0x02000000) -#define CSR_HW_IF_CONFIG_REG_PREPARE (0x08000000) +#define CSR_HW_IF_CONFIG_REG_BIT_HAP_WAKE_L1A (0x00080000) +#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) +#define CSR_HW_IF_CONFIG_REG_BIT_NIC_READY (0x00400000) /* PCI_OWN_SEM */ +#define CSR_HW_IF_CONFIG_REG_BIT_NIC_PREPARE_DONE (0x02000000) /* ME_OWN */ +#define CSR_HW_IF_CONFIG_REG_PREPARE (0x08000000) /* WAKE_ME */ -#define CSR_INT_PERIODIC_DIS (0x00) -#define CSR_INT_PERIODIC_ENA (0xFF) +#define CSR_INT_PERIODIC_DIS (0x00) /* disable periodic int*/ +#define CSR_INT_PERIODIC_ENA (0xFF) /* 255*32 usec ~ 8 msec*/ /* interrupt flags in INTA, set by uCode or hardware (e.g. dma), * acknowledged (reset) by host writing "1" to flagged bits. */ @@ -198,7 +239,44 @@ #define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) #define CSR_RESET_LINK_PWR_MGMT_DISABLED (0x80000000) -/* GP (general purpose) CONTROL */ +/* + * GP (general purpose) CONTROL REGISTER + * Bit fields: + * 27: HW_RF_KILL_SW + * Indicates state of (platform's) hardware RF-Kill switch + * 26-24: POWER_SAVE_TYPE + * Indicates current power-saving mode: + * 000 -- No power saving + * 001 -- MAC power-down + * 010 -- PHY (radio) power-down + * 011 -- Error + * 9-6: SYS_CONFIG + * Indicates current system configuration, reflecting pins on chip + * as forced high/low by device circuit board. + * 4: GOING_TO_SLEEP + * Indicates MAC is entering a power-saving sleep power-down. + * Not a good time to access device-internal resources. + * 3: MAC_ACCESS_REQ + * Host sets this to request and maintain MAC wakeup, to allow host + * access to device-internal resources. Host must wait for + * MAC_CLOCK_READY (and !GOING_TO_SLEEP) before accessing non-CSR + * device registers. + * 2: INIT_DONE + * Host sets this to put device into fully operational D0 power mode. + * Host resets this after SW_RESET to put device into low power mode. + * 0: MAC_CLOCK_READY + * Indicates MAC (ucode processor, etc.) is powered up and can run. + * Internal resources are accessible. + * NOTE: This does not indicate that the processor is actually running. + * NOTE: This does not indicate that 4965 or 3945 has completed + * init or post-power-down restore of internal SRAM memory. + * Use CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP as indication that + * SRAM is restored and uCode is in normal operation mode. + * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and + * do not need to save/restore it. + * NOTE: After device reset, this bit remains "0" until host sets + * INIT_DONE + */ #define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) #define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) #define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) @@ -231,28 +309,58 @@ #define CSR_EEPROM_REG_MSK_DATA (0xFFFF0000) /* EEPROM GP */ -#define CSR_EEPROM_GP_VALID_MSK (0x00000007) +#define CSR_EEPROM_GP_VALID_MSK (0x00000007) /* signature */ #define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) +#define CSR_EEPROM_GP_BAD_SIGNATURE_BOTH_EEP_AND_OTP (0x00000000) +#define CSR_EEPROM_GP_BAD_SIG_EEP_GOOD_SIG_OTP (0x00000001) +#define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002) +#define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004) + +/* One-time-programmable memory general purpose reg */ #define CSR_OTP_GP_REG_DEVICE_SELECT (0x00010000) /* 0 - EEPROM, 1 - OTP */ #define CSR_OTP_GP_REG_OTP_ACCESS_MODE (0x00020000) /* 0 - absolute, 1 - relative */ #define CSR_OTP_GP_REG_ECC_CORR_STATUS_MSK (0x00100000) /* bit 20 */ #define CSR_OTP_GP_REG_ECC_UNCORR_STATUS_MSK (0x00200000) /* bit 21 */ + +/* GP REG */ #define CSR_GP_REG_POWER_SAVE_STATUS_MSK (0x03000000) /* bit 24/25 */ #define CSR_GP_REG_NO_POWER_SAVE (0x00000000) #define CSR_GP_REG_MAC_POWER_SAVE (0x01000000) #define CSR_GP_REG_PHY_POWER_SAVE (0x02000000) #define CSR_GP_REG_POWER_SAVE_ERROR (0x03000000) -/* EEPROM signature */ -#define CSR_EEPROM_GP_BAD_SIGNATURE_BOTH_EEP_AND_OTP (0x00000000) -#define CSR_EEPROM_GP_BAD_SIG_EEP_GOOD_SIG_OTP (0x00000001) -#define CSR_EEPROM_GP_GOOD_SIG_EEP_LESS_THAN_4K (0x00000002) -#define CSR_EEPROM_GP_GOOD_SIG_EEP_MORE_THAN_4K (0x00000004) /* CSR GIO */ #define CSR_GIO_REG_VAL_L0S_ENABLED (0x00000002) -/* UCODE DRV GP */ +/* + * UCODE-DRIVER GP (general purpose) mailbox register 1 + * Host driver and uCode write and/or read this register to communicate with + * each other. + * Bit fields: + * 4: UCODE_DISABLE + * Host sets this to request permanent halt of uCode, same as + * sending CARD_STATE command with "halt" bit set. + * 3: CT_KILL_EXIT + * Host sets this to request exit from CT_KILL state, i.e. host thinks + * device temperature is low enough to continue normal operation. + * 2: CMD_BLOCKED + * Host sets this during RF KILL power-down sequence (HW, SW, CT KILL) + * to release uCode to clear all Tx and command queues, enter + * unassociated mode, and power down. + * NOTE: Some devices also use HBUS_TARG_MBX_C register for this bit. + * 1: SW_BIT_RFKILL + * Host sets this when issuing CARD_STATE command to request + * device sleep. + * 0: MAC_SLEEP + * uCode sets this when preparing a power-saving power-down. + * uCode resets this when power-up is complete and SRAM is sane. + * NOTE: 3945/4965 saves internal SRAM data to host when powering down, + * and must restore this data after powering back up. + * MAC_SLEEP is the best indication that restore is complete. + * Later devices (5xxx/6xxx/1xxx) use non-volatile SRAM, and + * do not need to save/restore it. + */ #define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) #define CSR_UCODE_SW_BIT_RFKILL (0x00000002) #define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) @@ -265,7 +373,7 @@ #define CSR_GP_DRIVER_REG_BIT_RADIO_SKU_2x2_IPA (0x00000002) -/* GI Chicken Bits */ +/* GIO Chicken Bits (PCI Express bus link power management) */ #define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) #define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) @@ -285,8 +393,23 @@ #define CSR_DRAM_INT_TBL_ENABLE (1 << 31) #define CSR_DRAM_INIT_TBL_WRAP_CHECK (1 << 27) -/*=== HBUS (Host-side Bus) ===*/ +/* + * HBUS (Host-side Bus) + * + * HBUS registers are mapped directly into PCI bus space, but are used + * to indirectly access device's internal memory or registers that + * may be powered-down. + * + * Use iwl_write_direct32()/iwl_read_direct32() family for these registers; + * host must "grab nic access" via CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ + * to make sure the MAC (uCode processor, etc.) is powered up for accessing + * internal resources. + * + * Do not use iwl_write32()/iwl_read32() family to access these registers; + * these provide only simple PCI bus access, without waking up the MAC. + */ #define HBUS_BASE (0x400) + /* * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM * structures, error log, event log, verifying uCode load). @@ -301,6 +424,10 @@ #define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) #define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) +/* Mailbox C, used as workaround alternative to CSR_UCODE_DRV_GP1 mailbox */ +#define HBUS_TARG_MBX_C (HBUS_BASE+0x030) +#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) + /* * Registers for accessing device's internal peripheral registers * (e.g. SCD, BSM, etc.). First write to address register, @@ -315,16 +442,12 @@ #define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) /* - * Per-Tx-queue write pointer (index, really!) (3945 and 4965). + * Per-Tx-queue write pointer (index, really!) * Indicates index to next TFD that driver will fill (1 past latest filled). * Bit usage: * 0-7: queue write index * 11-8: queue selector */ #define HBUS_TARG_WRPTR (HBUS_BASE+0x060) -#define HBUS_TARG_MBX_C (HBUS_BASE+0x030) - -#define HBUS_TARG_MBX_C_REG_BIT_CMD_BLOCKED (0x00000004) - #endif /* !__iwl_csr_h__ */ |