diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-4965-hw.h')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-4965-hw.h | 792 |
1 files changed, 0 insertions, 792 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h b/drivers/net/wireless/iwlwifi/iwl-4965-hw.h deleted file mode 100644 index 9166794eda0d..000000000000 --- a/drivers/net/wireless/iwlwifi/iwl-4965-hw.h +++ /dev/null @@ -1,792 +0,0 @@ -/****************************************************************************** - * - * This file is provided under a dual BSD/GPLv2 license. When using or - * redistributing this file, you may do so under either license. - * - * GPL LICENSE SUMMARY - * - * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of version 2 of the GNU General Public License as - * published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be useful, but - * WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110, - * USA - * - * The full GNU General Public License is included in this distribution - * in the file called LICENSE.GPL. - * - * Contact Information: - * Intel Linux Wireless <ilw@linux.intel.com> - * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 - * - * BSD LICENSE - * - * Copyright(c) 2005 - 2010 Intel Corporation. All rights reserved. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * * Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * * Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in - * the documentation and/or other materials provided with the - * distribution. - * * Neither the name Intel Corporation nor the names of its - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - *****************************************************************************/ -/* - * Please use this file (iwl-4965-hw.h) only for hardware-related definitions. - * Use iwl-commands.h for uCode API definitions. - * Use iwl-dev.h for driver implementation definitions. - */ - -#ifndef __iwl_4965_hw_h__ -#define __iwl_4965_hw_h__ - -#include "iwl-fh.h" - -/* EEPROM */ -#define IWL4965_EEPROM_IMG_SIZE 1024 - -/* - * uCode queue management definitions ... - * The first queue used for block-ack aggregation is #7 (4965 only). - * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7. - */ -#define IWL49_FIRST_AMPDU_QUEUE 7 - -/* Sizes and addresses for instruction and data memory (SRAM) in - * 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */ -#define IWL49_RTC_INST_LOWER_BOUND (0x000000) -#define IWL49_RTC_INST_UPPER_BOUND (0x018000) - -#define IWL49_RTC_DATA_LOWER_BOUND (0x800000) -#define IWL49_RTC_DATA_UPPER_BOUND (0x80A000) - -#define IWL49_RTC_INST_SIZE (IWL49_RTC_INST_UPPER_BOUND - \ - IWL49_RTC_INST_LOWER_BOUND) -#define IWL49_RTC_DATA_SIZE (IWL49_RTC_DATA_UPPER_BOUND - \ - IWL49_RTC_DATA_LOWER_BOUND) - -#define IWL49_MAX_INST_SIZE IWL49_RTC_INST_SIZE -#define IWL49_MAX_DATA_SIZE IWL49_RTC_DATA_SIZE - -/* Size of uCode instruction memory in bootstrap state machine */ -#define IWL49_MAX_BSM_SIZE BSM_SRAM_SIZE - -static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr) -{ - return (addr >= IWL49_RTC_DATA_LOWER_BOUND) && - (addr < IWL49_RTC_DATA_UPPER_BOUND); -} - -/********************* START TEMPERATURE *************************************/ - -/** - * 4965 temperature calculation. - * - * The driver must calculate the device temperature before calculating - * a txpower setting (amplifier gain is temperature dependent). The - * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration - * values used for the life of the driver, and one of which (R4) is the - * real-time temperature indicator. - * - * uCode provides all 4 values to the driver via the "initialize alive" - * notification (see struct iwl4965_init_alive_resp). After the runtime uCode - * image loads, uCode updates the R4 value via statistics notifications - * (see STATISTICS_NOTIFICATION), which occur after each received beacon - * when associated, or can be requested via REPLY_STATISTICS_CMD. - * - * NOTE: uCode provides the R4 value as a 23-bit signed value. Driver - * must sign-extend to 32 bits before applying formula below. - * - * Formula: - * - * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8 - * - * NOTE: The basic formula is 259 * (R4-R2) / (R3-R1). The 97/100 is - * an additional correction, which should be centered around 0 degrees - * Celsius (273 degrees Kelvin). The 8 (3 percent of 273) compensates for - * centering the 97/100 correction around 0 degrees K. - * - * Add 273 to Kelvin value to find degrees Celsius, for comparing current - * temperature with factory-measured temperatures when calculating txpower - * settings. - */ -#define TEMPERATURE_CALIB_KELVIN_OFFSET 8 -#define TEMPERATURE_CALIB_A_VAL 259 - -/* Limit range of calculated temperature to be between these Kelvin values */ -#define IWL_TX_POWER_TEMPERATURE_MIN (263) -#define IWL_TX_POWER_TEMPERATURE_MAX (410) - -#define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \ - (((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \ - ((t) > IWL_TX_POWER_TEMPERATURE_MAX)) - -/********************* END TEMPERATURE ***************************************/ - -/********************* START TXPOWER *****************************************/ - -/** - * 4965 txpower calculations rely on information from three sources: - * - * 1) EEPROM - * 2) "initialize" alive notification - * 3) statistics notifications - * - * EEPROM data consists of: - * - * 1) Regulatory information (max txpower and channel usage flags) is provided - * separately for each channel that can possibly supported by 4965. - * 40 MHz wide (.11n HT40) channels are listed separately from 20 MHz - * (legacy) channels. - * - * See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom - * for locations in EEPROM. - * - * 2) Factory txpower calibration information is provided separately for - * sub-bands of contiguous channels. 2.4GHz has just one sub-band, - * but 5 GHz has several sub-bands. - * - * In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided. - * - * See struct iwl4965_eeprom_calib_info (and the tree of structures - * contained within it) for format, and struct iwl4965_eeprom for - * locations in EEPROM. - * - * "Initialization alive" notification (see struct iwl4965_init_alive_resp) - * consists of: - * - * 1) Temperature calculation parameters. - * - * 2) Power supply voltage measurement. - * - * 3) Tx gain compensation to balance 2 transmitters for MIMO use. - * - * Statistics notifications deliver: - * - * 1) Current values for temperature param R4. - */ - -/** - * To calculate a txpower setting for a given desired target txpower, channel, - * modulation bit rate, and transmitter chain (4965 has 2 transmitters to - * support MIMO and transmit diversity), driver must do the following: - * - * 1) Compare desired txpower vs. (EEPROM) regulatory limit for this channel. - * Do not exceed regulatory limit; reduce target txpower if necessary. - * - * If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31), - * 2 transmitters will be used simultaneously; driver must reduce the - * regulatory limit by 3 dB (half-power) for each transmitter, so the - * combined total output of the 2 transmitters is within regulatory limits. - * - * - * 2) Compare target txpower vs. (EEPROM) saturation txpower *reduced by - * backoff for this bit rate*. Do not exceed (saturation - backoff[rate]); - * reduce target txpower if necessary. - * - * Backoff values below are in 1/2 dB units (equivalent to steps in - * txpower gain tables): - * - * OFDM 6 - 36 MBit: 10 steps (5 dB) - * OFDM 48 MBit: 15 steps (7.5 dB) - * OFDM 54 MBit: 17 steps (8.5 dB) - * OFDM 60 MBit: 20 steps (10 dB) - * CCK all rates: 10 steps (5 dB) - * - * Backoff values apply to saturation txpower on a per-transmitter basis; - * when using MIMO (2 transmitters), each transmitter uses the same - * saturation level provided in EEPROM, and the same backoff values; - * no reduction (such as with regulatory txpower limits) is required. - * - * Saturation and Backoff values apply equally to 20 Mhz (legacy) channel - * widths and 40 Mhz (.11n HT40) channel widths; there is no separate - * factory measurement for ht40 channels. - * - * The result of this step is the final target txpower. The rest of - * the steps figure out the proper settings for the device to achieve - * that target txpower. - * - * - * 3) Determine (EEPROM) calibration sub band for the target channel, by - * comparing against first and last channels in each sub band - * (see struct iwl4965_eeprom_calib_subband_info). - * - * - * 4) Linearly interpolate (EEPROM) factory calibration measurement sets, - * referencing the 2 factory-measured (sample) channels within the sub band. - * - * Interpolation is based on difference between target channel's frequency - * and the sample channels' frequencies. Since channel numbers are based - * on frequency (5 MHz between each channel number), this is equivalent - * to interpolating based on channel number differences. - * - * Note that the sample channels may or may not be the channels at the - * edges of the sub band. The target channel may be "outside" of the - * span of the sampled channels. - * - * Driver may choose the pair (for 2 Tx chains) of measurements (see - * struct iwl4965_eeprom_calib_ch_info) for which the actual measured - * txpower comes closest to the desired txpower. Usually, though, - * the middle set of measurements is closest to the regulatory limits, - * and is therefore a good choice for all txpower calculations (this - * assumes that high accuracy is needed for maximizing legal txpower, - * while lower txpower configurations do not need as much accuracy). - * - * Driver should interpolate both members of the chosen measurement pair, - * i.e. for both Tx chains (radio transmitters), unless the driver knows - * that only one of the chains will be used (e.g. only one tx antenna - * connected, but this should be unusual). The rate scaling algorithm - * switches antennas to find best performance, so both Tx chains will - * be used (although only one at a time) even for non-MIMO transmissions. - * - * Driver should interpolate factory values for temperature, gain table - * index, and actual power. The power amplifier detector values are - * not used by the driver. - * - * Sanity check: If the target channel happens to be one of the sample - * channels, the results should agree with the sample channel's - * measurements! - * - * - * 5) Find difference between desired txpower and (interpolated) - * factory-measured txpower. Using (interpolated) factory gain table index - * (shown elsewhere) as a starting point, adjust this index lower to - * increase txpower, or higher to decrease txpower, until the target - * txpower is reached. Each step in the gain table is 1/2 dB. - * - * For example, if factory measured txpower is 16 dBm, and target txpower - * is 13 dBm, add 6 steps to the factory gain index to reduce txpower - * by 3 dB. - * - * - * 6) Find difference between current device temperature and (interpolated) - * factory-measured temperature for sub-band. Factory values are in - * degrees Celsius. To calculate current temperature, see comments for - * "4965 temperature calculation". - * - * If current temperature is higher than factory temperature, driver must - * increase gain (lower gain table index), and vice verse. - * - * Temperature affects gain differently for different channels: - * - * 2.4 GHz all channels: 3.5 degrees per half-dB step - * 5 GHz channels 34-43: 4.5 degrees per half-dB step - * 5 GHz channels >= 44: 4.0 degrees per half-dB step - * - * NOTE: Temperature can increase rapidly when transmitting, especially - * with heavy traffic at high txpowers. Driver should update - * temperature calculations often under these conditions to - * maintain strong txpower in the face of rising temperature. - * - * - * 7) Find difference between current power supply voltage indicator - * (from "initialize alive") and factory-measured power supply voltage - * indicator (EEPROM). - * - * If the current voltage is higher (indicator is lower) than factory - * voltage, gain should be reduced (gain table index increased) by: - * - * (eeprom - current) / 7 - * - * If the current voltage is lower (indicator is higher) than factory - * voltage, gain should be increased (gain table index decreased) by: - * - * 2 * (current - eeprom) / 7 - * - * If number of index steps in either direction turns out to be > 2, - * something is wrong ... just use 0. - * - * NOTE: Voltage compensation is independent of band/channel. - * - * NOTE: "Initialize" uCode measures current voltage, which is assumed - * to be constant after this initial measurement. Voltage - * compensation for txpower (number of steps in gain table) - * may be calculated once and used until the next uCode bootload. - * - * - * 8) If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31), - * adjust txpower for each transmitter chain, so txpower is balanced - * between the two chains. There are 5 pairs of tx_atten[group][chain] - * values in "initialize alive", one pair for each of 5 channel ranges: - * - * Group 0: 5 GHz channel 34-43 - * Group 1: 5 GHz channel 44-70 - * Group 2: 5 GHz channel 71-124 - * Group 3: 5 GHz channel 125-200 - * Group 4: 2.4 GHz all channels - * - * Add the tx_atten[group][chain] value to the index for the target chain. - * The values are signed, but are in pairs of 0 and a non-negative number, - * so as to reduce gain (if necessary) of the "hotter" channel. This - * avoids any need to double-check for regulatory compliance after - * this step. - * - * - * 9) If setting up for a CCK rate, lower the gain by adding a CCK compensation - * value to the index: - * - * Hardware rev B: 9 steps (4.5 dB) - * Hardware rev C: 5 steps (2.5 dB) - * - * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG, - * bits [3:2], 1 = B, 2 = C. - * - * NOTE: This compensation is in addition to any saturation backoff that - * might have been applied in an earlier step. - * - * - * 10) Select the gain table, based on band (2.4 vs 5 GHz). - * - * Limit the adjusted index to stay within the table! - * - * - * 11) Read gain table entries for DSP and radio gain, place into appropriate - * location(s) in command (struct iwl4965_txpowertable_cmd). - */ - -/** - * When MIMO is used (2 transmitters operating simultaneously), driver should - * limit each transmitter to deliver a max of 3 dB below the regulatory limit - * for the device. That is, use half power for each transmitter, so total - * txpower is within regulatory limits. - * - * The value "6" represents number of steps in gain table to reduce power 3 dB. - * Each step is 1/2 dB. - */ -#define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6) - -/** - * CCK gain compensation. - * - * When calculating txpowers for CCK, after making sure that the target power - * is within regulatory and saturation limits, driver must additionally - * back off gain by adding these values to the gain table index. - * - * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG, - * bits [3:2], 1 = B, 2 = C. - */ -#define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9) -#define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5) - -/* - * 4965 power supply voltage compensation for txpower - */ -#define TX_POWER_IWL_VOLTAGE_CODES_PER_03V (7) - -/** - * Gain tables. - * - * The following tables contain pair of values for setting txpower, i.e. - * gain settings for the output of the device's digital signal processor (DSP), - * and for the analog gain structure of the transmitter. - * - * Each entry in the gain tables represents a step of 1/2 dB. Note that these - * are *relative* steps, not indications of absolute output power. Output - * power varies with temperature, voltage, and channel frequency, and also - * requires consideration of average power (to satisfy regulatory constraints), - * and peak power (to avoid distortion of the output signal). - * - * Each entry contains two values: - * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained - * linear value that multiplies the output of the digital signal processor, - * before being sent to the analog radio. - * 2) Radio gain. This sets the analog gain of the radio Tx path. - * It is a coarser setting, and behaves in a logarithmic (dB) fashion. - * - * EEPROM contains factory calibration data for txpower. This maps actual - * measured txpower levels to gain settings in the "well known" tables - * below ("well-known" means here that both factory calibration *and* the - * driver work with the same table). - * - * There are separate tables for 2.4 GHz and 5 GHz bands. The 5 GHz table - * has an extension (into negative indexes), in case the driver needs to - * boost power setting for high device temperatures (higher than would be - * present during factory calibration). A 5 Ghz EEPROM index of "40" - * corresponds to the 49th entry in the table used by the driver. - */ -#define MIN_TX_GAIN_INDEX (0) /* highest gain, lowest idx, 2.4 */ -#define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9) /* highest gain, lowest idx, 5 */ - -/** - * 2.4 GHz gain table - * - * Index Dsp gain Radio gain - * 0 110 0x3f (highest gain) - * 1 104 0x3f - * 2 98 0x3f - * 3 110 0x3e - * 4 104 0x3e - * 5 98 0x3e - * 6 110 0x3d - * 7 104 0x3d - * 8 98 0x3d - * 9 110 0x3c - * 10 104 0x3c - * 11 98 0x3c - * 12 110 0x3b - * 13 104 0x3b - * 14 98 0x3b - * 15 110 0x3a - * 16 104 0x3a - * 17 98 0x3a - * 18 110 0x39 - * 19 104 0x39 - * 20 98 0x39 - * 21 110 0x38 - * 22 104 0x38 - * 23 98 0x38 - * 24 110 0x37 - * 25 104 0x37 - * 26 98 0x37 - * 27 110 0x36 - * 28 104 0x36 - * 29 98 0x36 - * 30 110 0x35 - * 31 104 0x35 - * 32 98 0x35 - * 33 110 0x34 - * 34 104 0x34 - * 35 98 0x34 - * 36 110 0x33 - * 37 104 0x33 - * 38 98 0x33 - * 39 110 0x32 - * 40 104 0x32 - * 41 98 0x32 - * 42 110 0x31 - * 43 104 0x31 - * 44 98 0x31 - * 45 110 0x30 - * 46 104 0x30 - * 47 98 0x30 - * 48 110 0x6 - * 49 104 0x6 - * 50 98 0x6 - * 51 110 0x5 - * 52 104 0x5 - * 53 98 0x5 - * 54 110 0x4 - * 55 104 0x4 - * 56 98 0x4 - * 57 110 0x3 - * 58 104 0x3 - * 59 98 0x3 - * 60 110 0x2 - * 61 104 0x2 - * 62 98 0x2 - * 63 110 0x1 - * 64 104 0x1 - * 65 98 0x1 - * 66 110 0x0 - * 67 104 0x0 - * 68 98 0x0 - * 69 97 0 - * 70 96 0 - * 71 95 0 - * 72 94 0 - * 73 93 0 - * 74 92 0 - * 75 91 0 - * 76 90 0 - * 77 89 0 - * 78 88 0 - * 79 87 0 - * 80 86 0 - * 81 85 0 - * 82 84 0 - * 83 83 0 - * 84 82 0 - * 85 81 0 - * 86 80 0 - * 87 79 0 - * 88 78 0 - * 89 77 0 - * 90 76 0 - * 91 75 0 - * 92 74 0 - * 93 73 0 - * 94 72 0 - * 95 71 0 - * 96 70 0 - * 97 69 0 - * 98 68 0 - */ - -/** - * 5 GHz gain table - * - * Index Dsp gain Radio gain - * -9 123 0x3F (highest gain) - * -8 117 0x3F - * -7 110 0x3F - * -6 104 0x3F - * -5 98 0x3F - * -4 110 0x3E - * -3 104 0x3E - * -2 98 0x3E - * -1 110 0x3D - * 0 104 0x3D - * 1 98 0x3D - * 2 110 0x3C - * 3 104 0x3C - * 4 98 0x3C - * 5 110 0x3B - * 6 104 0x3B - * 7 98 0x3B - * 8 110 0x3A - * 9 104 0x3A - * 10 98 0x3A - * 11 110 0x39 - * 12 104 0x39 - * 13 98 0x39 - * 14 110 0x38 - * 15 104 0x38 - * 16 98 0x38 - * 17 110 0x37 - * 18 104 0x37 - * 19 98 0x37 - * 20 110 0x36 - * 21 104 0x36 - * 22 98 0x36 - * 23 110 0x35 - * 24 104 0x35 - * 25 98 0x35 - * 26 110 0x34 - * 27 104 0x34 - * 28 98 0x34 - * 29 110 0x33 - * 30 104 0x33 - * 31 98 0x33 - * 32 110 0x32 - * 33 104 0x32 - * 34 98 0x32 - * 35 110 0x31 - * 36 104 0x31 - * 37 98 0x31 - * 38 110 0x30 - * 39 104 0x30 - * 40 98 0x30 - * 41 110 0x25 - * 42 104 0x25 - * 43 98 0x25 - * 44 110 0x24 - * 45 104 0x24 - * 46 98 0x24 - * 47 110 0x23 - * 48 104 0x23 - * 49 98 0x23 - * 50 110 0x22 - * 51 104 0x18 - * 52 98 0x18 - * 53 110 0x17 - * 54 104 0x17 - * 55 98 0x17 - * 56 110 0x16 - * 57 104 0x16 - * 58 98 0x16 - * 59 110 0x15 - * 60 104 0x15 - * 61 98 0x15 - * 62 110 0x14 - * 63 104 0x14 - * 64 98 0x14 - * 65 110 0x13 - * 66 104 0x13 - * 67 98 0x13 - * 68 110 0x12 - * 69 104 0x08 - * 70 98 0x08 - * 71 110 0x07 - * 72 104 0x07 - * 73 98 0x07 - * 74 110 0x06 - * 75 104 0x06 - * 76 98 0x06 - * 77 110 0x05 - * 78 104 0x05 - * 79 98 0x05 - * 80 110 0x04 - * 81 104 0x04 - * 82 98 0x04 - * 83 110 0x03 - * 84 104 0x03 - * 85 98 0x03 - * 86 110 0x02 - * 87 104 0x02 - * 88 98 0x02 - * 89 110 0x01 - * 90 104 0x01 - * 91 98 0x01 - * 92 110 0x00 - * 93 104 0x00 - * 94 98 0x00 - * 95 93 0x00 - * 96 88 0x00 - * 97 83 0x00 - * 98 78 0x00 - */ - - -/** - * Sanity checks and default values for EEPROM regulatory levels. - * If EEPROM values fall outside MIN/MAX range, use default values. - * - * Regulatory limits refer to the maximum average txpower allowed by - * regulatory agencies in the geographies in which the device is meant - * to be operated. These limits are SKU-specific (i.e. geography-specific), - * and channel-specific; each channel has an individual regulatory limit - * listed in the EEPROM. - * - * Units are in half-dBm (i.e. "34" means 17 dBm). - */ -#define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34) -#define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34) -#define IWL_TX_POWER_REGULATORY_MIN (0) -#define IWL_TX_POWER_REGULATORY_MAX (34) - -/** - * Sanity checks and default values for EEPROM saturation levels. - * If EEPROM values fall outside MIN/MAX range, use default values. - * - * Saturation is the highest level that the output power amplifier can produce - * without significant clipping distortion. This is a "peak" power level. - * Different types of modulation (i.e. various "rates", and OFDM vs. CCK) - * require differing amounts of backoff, relative to their average power output, - * in order to avoid clipping distortion. - * - * Driver must make sure that it is violating neither the saturation limit, - * nor the regulatory limit, when calculating Tx power settings for various - * rates. - * - * Units are in half-dBm (i.e. "38" means 19 dBm). - */ -#define IWL_TX_POWER_DEFAULT_SATURATION_24 (38) -#define IWL_TX_POWER_DEFAULT_SATURATION_52 (38) -#define IWL_TX_POWER_SATURATION_MIN (20) -#define IWL_TX_POWER_SATURATION_MAX (50) - -/** - * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance) - * and thermal Txpower calibration. - * - * When calculating txpower, driver must compensate for current device - * temperature; higher temperature requires higher gain. Driver must calculate - * current temperature (see "4965 temperature calculation"), then compare vs. - * factory calibration temperature in EEPROM; if current temperature is higher - * than factory temperature, driver must *increase* gain by proportions shown - * in table below. If current temperature is lower than factory, driver must - * *decrease* gain. - * - * Different frequency ranges require different compensation, as shown below. - */ -/* Group 0, 5.2 GHz ch 34-43: 4.5 degrees per 1/2 dB. */ -#define CALIB_IWL_TX_ATTEN_GR1_FCH 34 -#define CALIB_IWL_TX_ATTEN_GR1_LCH 43 - -/* Group 1, 5.3 GHz ch 44-70: 4.0 degrees per 1/2 dB. */ -#define CALIB_IWL_TX_ATTEN_GR2_FCH 44 -#define CALIB_IWL_TX_ATTEN_GR2_LCH 70 - -/* Group 2, 5.5 GHz ch 71-124: 4.0 degrees per 1/2 dB. */ -#define CALIB_IWL_TX_ATTEN_GR3_FCH 71 -#define CALIB_IWL_TX_ATTEN_GR3_LCH 124 - -/* Group 3, 5.7 GHz ch 125-200: 4.0 degrees per 1/2 dB. */ -#define CALIB_IWL_TX_ATTEN_GR4_FCH 125 -#define CALIB_IWL_TX_ATTEN_GR4_LCH 200 - -/* Group 4, 2.4 GHz all channels: 3.5 degrees per 1/2 dB. */ -#define CALIB_IWL_TX_ATTEN_GR5_FCH 1 -#define CALIB_IWL_TX_ATTEN_GR5_LCH 20 - -enum { - CALIB_CH_GROUP_1 = 0, - CALIB_CH_GROUP_2 = 1, - CALIB_CH_GROUP_3 = 2, - CALIB_CH_GROUP_4 = 3, - CALIB_CH_GROUP_5 = 4, - CALIB_CH_GROUP_MAX -}; - -/********************* END TXPOWER *****************************************/ - - -/** - * Tx/Rx Queues - * - * Most communication between driver and 4965 is via queues of data buffers. - * For example, all commands that the driver issues to device's embedded - * controller (uCode) are via the command queue (one of the Tx queues). All - * uCode command responses/replies/notifications, including Rx frames, are - * conveyed from uCode to driver via the Rx queue. - * - * Most support for these queues, including handshake support, resides in - * structures in host DRAM, shared between the driver and the device. When - * allocating this memory, the driver must make sure that data written by - * the host CPU updates DRAM immediately (and does not get "stuck" in CPU's - * cache memory), so DRAM and cache are consistent, and the device can - * immediately see changes made by the driver. - * - * 4965 supports up to 16 DRAM-based Tx queues, and services these queues via - * up to 7 DMA channels (FIFOs). Each Tx queue is supported by a circular array - * in DRAM containing 256 Transmit Frame Descriptors (TFDs). - */ -#define IWL49_NUM_FIFOS 7 -#define IWL49_CMD_FIFO_NUM 4 -#define IWL49_NUM_QUEUES 16 -#define IWL49_NUM_AMPDU_QUEUES 8 - - -/** - * struct iwl4965_schedq_bc_tbl - * - * Byte Count table - * - * Each Tx queue uses a byte-count table containing 320 entries: - * one 16-bit entry for each of 256 TFDs, plus an additional 64 entries that - * duplicate the first 64 entries (to avoid wrap-around within a Tx window; - * max Tx window is 64 TFDs). - * - * When driver sets up a new TFD, it must also enter the total byte count - * of the frame to be transmitted into the corresponding entry in the byte - * count table for the chosen Tx queue. If the TFD index is 0-63, the driver - * must duplicate the byte count entry in corresponding index 256-319. - * - * padding puts each byte count table on a 1024-byte boundary; - * 4965 assumes tables are separated by 1024 bytes. - */ -struct iwl4965_scd_bc_tbl { - __le16 tfd_offset[TFD_QUEUE_BC_SIZE]; - u8 pad[1024 - (TFD_QUEUE_BC_SIZE) * sizeof(__le16)]; -} __packed; - -#endif /* !__iwl_4965_hw_h__ */ |