diff options
Diffstat (limited to 'drivers/net/phy')
| -rw-r--r-- | drivers/net/phy/Kconfig | 12 | ||||
| -rw-r--r-- | drivers/net/phy/Makefile | 12 | ||||
| -rw-r--r-- | drivers/net/phy/mdio_bus.c | 4 | ||||
| -rw-r--r-- | drivers/net/phy/phy.c | 9 | ||||
| -rw-r--r-- | drivers/net/phy/phy.c.orig | 860 | ||||
| -rw-r--r-- | drivers/net/phy/phy_device.c | 48 |
6 files changed, 53 insertions, 892 deletions
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index 8b5db2343cc3..c2f1bf1d02d2 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -5,7 +5,7 @@ menu "PHY device support" config PHYLIB - bool "PHY Device support and infrastructure" + tristate "PHY Device support and infrastructure" depends on NET_ETHERNET help Ethernet controllers are usually attached to PHY @@ -24,31 +24,31 @@ comment "MII PHY device drivers" depends on PHYLIB config MARVELL_PHY - bool "Drivers for Marvell PHYs" + tristate "Drivers for Marvell PHYs" depends on PHYLIB ---help--- Currently has a driver for the 88E1011S config DAVICOM_PHY - bool "Drivers for Davicom PHYs" + tristate "Drivers for Davicom PHYs" depends on PHYLIB ---help--- Currently supports dm9161e and dm9131 config QSEMI_PHY - bool "Drivers for Quality Semiconductor PHYs" + tristate "Drivers for Quality Semiconductor PHYs" depends on PHYLIB ---help--- Currently supports the qs6612 config LXT_PHY - bool "Drivers for the Intel LXT PHYs" + tristate "Drivers for the Intel LXT PHYs" depends on PHYLIB ---help--- Currently supports the lxt970, lxt971 config CICADA_PHY - bool "Drivers for the Cicada PHYs" + tristate "Drivers for the Cicada PHYs" depends on PHYLIB ---help--- Currently supports the cis8204 diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index 1af05de6ced0..fb7cb385a659 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -1,9 +1,9 @@ # Makefile for Linux PHY drivers -obj-$(CONFIG_PHYLIB) += phy.o phy_device.o mdio_bus.o +libphy-objs := phy.o phy_device.o mdio_bus.o -obj-$(CONFIG_MARVELL_PHY) += marvell.o -obj-$(CONFIG_DAVICOM_PHY) += davicom.o -obj-$(CONFIG_CICADA_PHY) += cicada.o -obj-$(CONFIG_LXT_PHY) += lxt.o -obj-$(CONFIG_QSEMI_PHY) += qsemi.o +obj-$(CONFIG_MARVELL_PHY) += libphy.o marvell.o +obj-$(CONFIG_DAVICOM_PHY) += libphy.o davicom.o +obj-$(CONFIG_CICADA_PHY) += libphy.o cicada.o +obj-$(CONFIG_LXT_PHY) += libphy.o lxt.o +obj-$(CONFIG_QSEMI_PHY) += libphy.o qsemi.o diff --git a/drivers/net/phy/mdio_bus.c b/drivers/net/phy/mdio_bus.c index e75103ba6f86..5fbea6acfe80 100644 --- a/drivers/net/phy/mdio_bus.c +++ b/drivers/net/phy/mdio_bus.c @@ -165,9 +165,9 @@ struct bus_type mdio_bus_type = { .resume = mdio_bus_resume, }; -static int __init mdio_bus_init(void) +int __init mdio_bus_init(void) { return bus_register(&mdio_bus_type); } -subsys_initcall(mdio_bus_init); + diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index e2c6896b92d2..934065dd6371 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -39,7 +39,6 @@ #include <asm/irq.h> #include <asm/uaccess.h> -static void phy_change(void *data); static void phy_timer(unsigned long data); /* Convenience function to print out the current phy status @@ -464,7 +463,6 @@ void phy_stop_machine(struct phy_device *phydev) phydev->adjust_state = NULL; } -#ifdef CONFIG_PHYCONTROL /* phy_error: * * Moves the PHY to the HALTED state in response to a read @@ -479,6 +477,10 @@ void phy_error(struct phy_device *phydev) spin_unlock(&phydev->lock); } +#ifdef CONFIG_PHYCONTROL + +static void phy_change(void *data); + /* phy_interrupt * * description: When a PHY interrupt occurs, the handler disables @@ -672,6 +674,8 @@ void phy_start(struct phy_device *phydev) EXPORT_SYMBOL(phy_stop); EXPORT_SYMBOL(phy_start); +#endif /* CONFIG_PHYCONTROL */ + /* PHY timer which handles the state machine */ static void phy_timer(unsigned long data) { @@ -859,4 +863,3 @@ static void phy_timer(unsigned long data) mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); } -#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy.c.orig b/drivers/net/phy/phy.c.orig deleted file mode 100644 index 6af17cec9ace..000000000000 --- a/drivers/net/phy/phy.c.orig +++ /dev/null @@ -1,860 +0,0 @@ -/* - * drivers/net/phy/phy.c - * - * Framework for configuring and reading PHY devices - * Based on code in sungem_phy.c and gianfar_phy.c - * - * Author: Andy Fleming - * - * Copyright (c) 2004 Freescale Semiconductor, Inc. - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - */ -#include <linux/config.h> -#include <linux/kernel.h> -#include <linux/sched.h> -#include <linux/string.h> -#include <linux/errno.h> -#include <linux/unistd.h> -#include <linux/slab.h> -#include <linux/interrupt.h> -#include <linux/init.h> -#include <linux/delay.h> -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> -#include <linux/spinlock.h> -#include <linux/mm.h> -#include <linux/module.h> -#include <linux/version.h> -#include <linux/mii.h> -#include <linux/ethtool.h> -#include <linux/phy.h> - -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/uaccess.h> - -static void phy_change(void *data); -static void phy_timer(unsigned long data); - -/* Convenience function to print out the current phy status - */ -void phy_print_status(struct phy_device *phydev) -{ - pr_info("%s: Link is %s", phydev->dev.bus_id, - phydev->link ? "Up" : "Down"); - if (phydev->link) - printk(" - %d/%s", phydev->speed, - DUPLEX_FULL == phydev->duplex ? - "Full" : "Half"); - - printk("\n"); -} -EXPORT_SYMBOL(phy_print_status); - - -/* Convenience functions for reading/writing a given PHY - * register. They MUST NOT be called from interrupt context, - * because the bus read/write functions may wait for an interrupt - * to conclude the operation. */ -int phy_read(struct phy_device *phydev, u16 regnum) -{ - int retval; - struct mii_bus *bus = phydev->bus; - - spin_lock_bh(&bus->mdio_lock); - retval = bus->read(bus, phydev->addr, regnum); - spin_unlock_bh(&bus->mdio_lock); - - return retval; -} -EXPORT_SYMBOL(phy_read); - -int phy_write(struct phy_device *phydev, u16 regnum, u16 val) -{ - int err; - struct mii_bus *bus = phydev->bus; - - spin_lock_bh(&bus->mdio_lock); - err = bus->write(bus, phydev->addr, regnum, val); - spin_unlock_bh(&bus->mdio_lock); - - return err; -} -EXPORT_SYMBOL(phy_write); - - -int phy_clear_interrupt(struct phy_device *phydev) -{ - int err = 0; - - if (phydev->drv->ack_interrupt) - err = phydev->drv->ack_interrupt(phydev); - - return err; -} - - -int phy_config_interrupt(struct phy_device *phydev, u32 interrupts) -{ - int err = 0; - - phydev->interrupts = interrupts; - if (phydev->drv->config_intr) - err = phydev->drv->config_intr(phydev); - - return err; -} - - -/* phy_aneg_done - * - * description: Reads the status register and returns 0 either if - * auto-negotiation is incomplete, or if there was an error. - * Returns BMSR_ANEGCOMPLETE if auto-negotiation is done. - */ -static inline int phy_aneg_done(struct phy_device *phydev) -{ - int retval; - - retval = phy_read(phydev, MII_BMSR); - - return (retval < 0) ? retval : (retval & BMSR_ANEGCOMPLETE); -} - -/* phy_start_aneg - * - * description: Calls the PHY driver's config_aneg, and then - * sets the PHY state to PHY_AN if auto-negotiation is enabled, - * and to PHY_FORCING if auto-negotiation is disabled. Unless - * the PHY is currently HALTED. - */ -int phy_start_aneg(struct phy_device *phydev) -{ - int err; - - spin_lock(&phydev->lock); - - if (AUTONEG_DISABLE == phydev->autoneg) - phy_sanitize_settings(phydev); - - err = phydev->drv->config_aneg(phydev); - - if (err < 0) - goto out_unlock; - - if (phydev->state != PHY_HALTED) { - if (AUTONEG_ENABLE == phydev->autoneg) { - phydev->state = PHY_AN; - phydev->link_timeout = PHY_AN_TIMEOUT; - } else { - phydev->state = PHY_FORCING; - phydev->link_timeout = PHY_FORCE_TIMEOUT; - } - } - -out_unlock: - spin_unlock(&phydev->lock); - return err; -} -EXPORT_SYMBOL(phy_start_aneg); - - -/* A structure for mapping a particular speed and duplex - * combination to a particular SUPPORTED and ADVERTISED value */ -struct phy_setting { - int speed; - int duplex; - u32 setting; -}; - -/* A mapping of all SUPPORTED settings to speed/duplex */ -static struct phy_setting settings[] = { - { - .speed = 10000, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_10000baseT_Full, - }, - { - .speed = SPEED_1000, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_1000baseT_Full, - }, - { - .speed = SPEED_1000, - .duplex = DUPLEX_HALF, - .setting = SUPPORTED_1000baseT_Half, - }, - { - .speed = SPEED_100, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_100baseT_Full, - }, - { - .speed = SPEED_100, - .duplex = DUPLEX_HALF, - .setting = SUPPORTED_100baseT_Half, - }, - { - .speed = SPEED_10, - .duplex = DUPLEX_FULL, - .setting = SUPPORTED_10baseT_Full, - }, - { - .speed = SPEED_10, - .duplex = DUPLEX_HALF, - .setting = SUPPORTED_10baseT_Half, - }, -}; - -#define MAX_NUM_SETTINGS (sizeof(settings)/sizeof(struct phy_setting)) - -/* phy_find_setting - * - * description: Searches the settings array for the setting which - * matches the desired speed and duplex, and returns the index - * of that setting. Returns the index of the last setting if - * none of the others match. - */ -static inline int phy_find_setting(int speed, int duplex) -{ - int idx = 0; - - while (idx < ARRAY_SIZE(settings) && - (settings[idx].speed != speed || - settings[idx].duplex != duplex)) - idx++; - - return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; -} - -/* phy_find_valid - * idx: The first index in settings[] to search - * features: A mask of the valid settings - * - * description: Returns the index of the first valid setting less - * than or equal to the one pointed to by idx, as determined by - * the mask in features. Returns the index of the last setting - * if nothing else matches. - */ -static inline int phy_find_valid(int idx, u32 features) -{ - while (idx < MAX_NUM_SETTINGS && !(settings[idx].setting & features)) - idx++; - - return idx < MAX_NUM_SETTINGS ? idx : MAX_NUM_SETTINGS - 1; -} - -/* phy_sanitize_settings - * - * description: Make sure the PHY is set to supported speeds and - * duplexes. Drop down by one in this order: 1000/FULL, - * 1000/HALF, 100/FULL, 100/HALF, 10/FULL, 10/HALF - */ -void phy_sanitize_settings(struct phy_device *phydev) -{ - u32 features = phydev->supported; - int idx; - - /* Sanitize settings based on PHY capabilities */ - if ((features & SUPPORTED_Autoneg) == 0) - phydev->autoneg = 0; - - idx = phy_find_valid(phy_find_setting(phydev->speed, phydev->duplex), - features); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; -} -EXPORT_SYMBOL(phy_sanitize_settings); - -/* phy_force_reduction - * - * description: Reduces the speed/duplex settings by - * one notch. The order is so: - * 1000/FULL, 1000/HALF, 100/FULL, 100/HALF, - * 10/FULL, 10/HALF. The function bottoms out at 10/HALF. - */ -static void phy_force_reduction(struct phy_device *phydev) -{ - int idx; - - idx = phy_find_setting(phydev->speed, phydev->duplex); - - idx++; - - idx = phy_find_valid(idx, phydev->supported); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; - - pr_info("Trying %d/%s\n", phydev->speed, - DUPLEX_FULL == phydev->duplex ? - "FULL" : "HALF"); -} - -/* phy_ethtool_sset: - * A generic ethtool sset function. Handles all the details - * - * A few notes about parameter checking: - * - We don't set port or transceiver, so we don't care what they - * were set to. - * - phy_start_aneg() will make sure forced settings are sane, and - * choose the next best ones from the ones selected, so we don't - * care if ethtool tries to give us bad values - */ -int phy_ethtool_sset(struct phy_device *phydev, struct ethtool_cmd *cmd) -{ - if (cmd->phy_address != phydev->addr) - return -EINVAL; - - /* We make sure that we don't pass unsupported - * values in to the PHY */ - cmd->advertising &= phydev->supported; - - /* Verify the settings we care about. */ - if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE) - return -EINVAL; - - if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0) - return -EINVAL; - - if (cmd->autoneg == AUTONEG_DISABLE - && ((cmd->speed != SPEED_1000 - && cmd->speed != SPEED_100 - && cmd->speed != SPEED_10) - || (cmd->duplex != DUPLEX_HALF - && cmd->duplex != DUPLEX_FULL))) - return -EINVAL; - - phydev->autoneg = cmd->autoneg; - - phydev->speed = cmd->speed; - - phydev->advertising = cmd->advertising; - - if (AUTONEG_ENABLE == cmd->autoneg) - phydev->advertising |= ADVERTISED_Autoneg; - else - phydev->advertising &= ~ADVERTISED_Autoneg; - - phydev->duplex = cmd->duplex; - - /* Restart the PHY */ - phy_start_aneg(phydev); - - return 0; -} - -int phy_ethtool_gset(struct phy_device *phydev, struct ethtool_cmd *cmd) -{ - cmd->supported = phydev->supported; - - cmd->advertising = phydev->advertising; - - cmd->speed = phydev->speed; - cmd->duplex = phydev->duplex; - cmd->port = PORT_MII; - cmd->phy_address = phydev->addr; - cmd->transceiver = XCVR_EXTERNAL; - cmd->autoneg = phydev->autoneg; - - return 0; -} - - -/* Note that this function is currently incompatible with the - * PHYCONTROL layer. It changes registers without regard to - * current state. Use at own risk - */ -int phy_mii_ioctl(struct phy_device *phydev, - struct mii_ioctl_data *mii_data, int cmd) -{ - u16 val = mii_data->val_in; - - switch (cmd) { - case SIOCGMIIPHY: - mii_data->phy_id = phydev->addr; - break; - case SIOCGMIIREG: - mii_data->val_out = phy_read(phydev, mii_data->reg_num); - break; - - case SIOCSMIIREG: - if (!capable(CAP_NET_ADMIN)) - return -EPERM; - - if (mii_data->phy_id == phydev->addr) { - switch(mii_data->reg_num) { - case MII_BMCR: - if (val & (BMCR_RESET|BMCR_ANENABLE)) - phydev->autoneg = AUTONEG_DISABLE; - else - phydev->autoneg = AUTONEG_ENABLE; - if ((!phydev->autoneg) && (val & BMCR_FULLDPLX)) - phydev->duplex = DUPLEX_FULL; - else - phydev->duplex = DUPLEX_HALF; - break; - case MII_ADVERTISE: - phydev->advertising = val; - break; - default: - /* do nothing */ - break; - } - } - - phy_write(phydev, mii_data->reg_num, val); - - if (mii_data->reg_num == MII_BMCR - && val & BMCR_RESET - && phydev->drv->config_init) - phydev->drv->config_init(phydev); - break; - } - - return 0; -} - -/* phy_start_machine: - * - * description: The PHY infrastructure can run a state machine - * which tracks whether the PHY is starting up, negotiating, - * etc. This function starts the timer which tracks the state - * of the PHY. If you want to be notified when the state - * changes, pass in the callback, otherwise, pass NULL. If you - * want to maintain your own state machine, do not call this - * function. */ -void phy_start_machine(struct phy_device *phydev, - void (*handler)(struct net_device *)) -{ - phydev->adjust_state = handler; - - init_timer(&phydev->phy_timer); - phydev->phy_timer.function = &phy_timer; - phydev->phy_timer.data = (unsigned long) phydev; - mod_timer(&phydev->phy_timer, jiffies + HZ); -} - -/* phy_stop_machine - * - * description: Stops the state machine timer, sets the state to - * UP (unless it wasn't up yet), and then frees the interrupt, - * if it is in use. This function must be called BEFORE - * phy_detach. - */ -void phy_stop_machine(struct phy_device *phydev) -{ - del_timer_sync(&phydev->phy_timer); - - spin_lock(&phydev->lock); - if (phydev->state > PHY_UP) - phydev->state = PHY_UP; - spin_unlock(&phydev->lock); - - if (phydev->irq != PHY_POLL) - phy_stop_interrupts(phydev); - - phydev->adjust_state = NULL; -} - -#ifdef CONFIG_PHYCONTROL -/* phy_error: - * - * Moves the PHY to the HALTED state in response to a read - * or write error, and tells the controller the link is down. - * Must not be called from interrupt context, or while the - * phydev->lock is held. - */ -void phy_error(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - phydev->state = PHY_HALTED; - spin_unlock(&phydev->lock); -} - -/* phy_interrupt - * - * description: When a PHY interrupt occurs, the handler disables - * interrupts, and schedules a work task to clear the interrupt. - */ -static irqreturn_t phy_interrupt(int irq, void *phy_dat, struct pt_regs *regs) -{ - struct phy_device *phydev = phy_dat; - - /* The MDIO bus is not allowed to be written in interrupt - * context, so we need to disable the irq here. A work - * queue will write the PHY to disable and clear the - * interrupt, and then reenable the irq line. */ - disable_irq_nosync(irq); - - schedule_work(&phydev->phy_queue); - - return IRQ_HANDLED; -} - -/* Enable the interrupts from the PHY side */ -int phy_enable_interrupts(struct phy_device *phydev) -{ - int err; - - err = phy_clear_interrupt(phydev); - - if (err < 0) - return err; - - err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); - - return err; -} - -/* Disable the PHY interrupts from the PHY side */ -int phy_disable_interrupts(struct phy_device *phydev) -{ - int err; - - /* Disable PHY interrupts */ - err = phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); - - if (err) - goto phy_err; - - /* Clear the interrupt */ - err = phy_clear_interrupt(phydev); - - if (err) - goto phy_err; - - return 0; - -phy_err: - phy_error(phydev); - - return err; -} - -/* phy_start_interrupts - * - * description: Request the interrupt for the given PHY. If - * this fails, then we set irq to PHY_POLL. - * Otherwise, we enable the interrupts in the PHY. - * Returns 0 on success. - * This should only be called with a valid IRQ number. - */ -int phy_start_interrupts(struct phy_device *phydev) -{ - int err = 0; - - INIT_WORK(&phydev->phy_queue, phy_change, phydev); - - if (request_irq(phydev->irq, phy_interrupt, - SA_SHIRQ, - "phy_interrupt", - phydev) < 0) { - printk(KERN_WARNING "%s: Can't get IRQ %d (PHY)\n", - phydev->bus->name, - phydev->irq); - phydev->irq = PHY_POLL; - return 0; - } - - err = phy_enable_interrupts(phydev); - - return err; -} -EXPORT_SYMBOL(phy_start_interrupts); - -int phy_stop_interrupts(struct phy_device *phydev) -{ - int err; - - err = phy_disable_interrupts(phydev); - - if (err) - phy_error(phydev); - - free_irq(phydev->irq, phydev); - - return err; -} -EXPORT_SYMBOL(phy_stop_interrupts); - - -/* Scheduled by the phy_interrupt/timer to handle PHY changes */ -static void phy_change(void *data) -{ - int err; - struct phy_device *phydev = data; - - err = phy_disable_interrupts(phydev); - - if (err) - goto phy_err; - - spin_lock(&phydev->lock); - if ((PHY_RUNNING == phydev->state) || (PHY_NOLINK == phydev->state)) - phydev->state = PHY_CHANGELINK; - spin_unlock(&phydev->lock); - - enable_irq(phydev->irq); - - /* Reenable interrupts */ - err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED); - - if (err) - goto irq_enable_err; - - return; - -irq_enable_err: - disable_irq(phydev->irq); -phy_err: - phy_error(phydev); -} - -/* Bring down the PHY link, and stop checking the status. */ -void phy_stop(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - - if (PHY_HALTED == phydev->state) - goto out_unlock; - - if (phydev->irq != PHY_POLL) { - /* Clear any pending interrupts */ - phy_clear_interrupt(phydev); - - /* Disable PHY Interrupts */ - phy_config_interrupt(phydev, PHY_INTERRUPT_DISABLED); - } - - phydev->state = PHY_HALTED; - -out_unlock: - spin_unlock(&phydev->lock); -} - - -/* phy_start - * - * description: Indicates the attached device's readiness to - * handle PHY-related work. Used during startup to start the - * PHY, and after a call to phy_stop() to resume operation. - * Also used to indicate the MDIO bus has cleared an error - * condition. - */ -void phy_start(struct phy_device *phydev) -{ - spin_lock(&phydev->lock); - - switch (phydev->state) { - case PHY_STARTING: - phydev->state = PHY_PENDING; - break; - case PHY_READY: - phydev->state = PHY_UP; - break; - case PHY_HALTED: - phydev->state = PHY_RESUMING; - default: - break; - } - spin_unlock(&phydev->lock); -} -EXPORT_SYMBOL(phy_stop); -EXPORT_SYMBOL(phy_start); - -/* PHY timer which handles the state machine */ -static void phy_timer(unsigned long data) -{ - struct phy_device *phydev = (struct phy_device *)data; - int needs_aneg = 0; - int err = 0; - - spin_lock(&phydev->lock); - - if (phydev->adjust_state) - phydev->adjust_state(phydev->attached_dev); - - switch(phydev->state) { - case PHY_DOWN: - case PHY_STARTING: - case PHY_READY: - case PHY_PENDING: - break; - case PHY_UP: - needs_aneg = 1; - - phydev->link_timeout = PHY_AN_TIMEOUT; - - break; - case PHY_AN: - /* Check if negotiation is done. Break - * if there's an error */ - err = phy_aneg_done(phydev); - if (err < 0) - break; - - /* If auto-negotiation is done, we change to - * either RUNNING, or NOLINK */ - if (err > 0) { - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - } else { - phydev->state = PHY_NOLINK; - netif_carrier_off(phydev->attached_dev); - } - - phydev->adjust_link(phydev->attached_dev); - - } else if (0 == phydev->link_timeout--) { - /* The counter expired, so either we - * switch to forced mode, or the - * magic_aneg bit exists, and we try aneg - * again */ - if (!(phydev->drv->flags & PHY_HAS_MAGICANEG)) { - int idx; - - /* We'll start from the - * fastest speed, and work - * our way down */ - idx = phy_find_valid(0, - phydev->supported); - - phydev->speed = settings[idx].speed; - phydev->duplex = settings[idx].duplex; - - phydev->autoneg = AUTONEG_DISABLE; - phydev->state = PHY_FORCING; - phydev->link_timeout = - PHY_FORCE_TIMEOUT; - - pr_info("Trying %d/%s\n", - phydev->speed, - DUPLEX_FULL == - phydev->duplex ? - "FULL" : "HALF"); - } - - needs_aneg = 1; - } - break; - case PHY_NOLINK: - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - phydev->adjust_link(phydev->attached_dev); - } - break; - case PHY_FORCING: - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - } else { - if (0 == phydev->link_timeout--) { - phy_force_reduction(phydev); - needs_aneg = 1; - } - } - - phydev->adjust_link(phydev->attached_dev); - break; - case PHY_RUNNING: - /* Only register a CHANGE if we are - * polling */ - if (PHY_POLL == phydev->irq) - phydev->state = PHY_CHANGELINK; - break; - case PHY_CHANGELINK: - err = phy_read_status(phydev); - - if (err) - break; - - if (phydev->link) { - phydev->state = PHY_RUNNING; - netif_carrier_on(phydev->attached_dev); - } else { - phydev->state = PHY_NOLINK; - netif_carrier_off(phydev->attached_dev); - } - - phydev->adjust_link(phydev->attached_dev); - - if (PHY_POLL != phydev->irq) - err = phy_config_interrupt(phydev, - PHY_INTERRUPT_ENABLED); - break; - case PHY_HALTED: - if (phydev->link) { - phydev->link = 0; - netif_carrier_off(phydev->attached_dev); - phydev->adjust_link(phydev->attached_dev); - } - break; - case PHY_RESUMING: - - err = phy_clear_interrupt(phydev); - - if (err) - break; - - err = phy_config_interrupt(phydev, - PHY_INTERRUPT_ENABLED); - - if (err) - break; - - if (AUTONEG_ENABLE == phydev->autoneg) { - err = phy_aneg_done(phydev); - if (err < 0) - break; - - /* err > 0 if AN is done. - * Otherwise, it's 0, and we're - * still waiting for AN */ - if (err > 0) { - phydev->state = PHY_RUNNING; - } else { - phydev->state = PHY_AN; - phydev->link_timeout = PHY_AN_TIMEOUT; - } - } else - phydev->state = PHY_RUNNING; - break; - } - - spin_unlock(&phydev->lock); - - if (needs_aneg) - err = phy_start_aneg(phydev); - - if (err < 0) - phy_error(phydev); - - mod_timer(&phydev->phy_timer, jiffies + PHY_STATE_TIME * HZ); -} - -#endif /* CONFIG_PHYCONTROL */ diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index f0595af4c837..c11138330fed 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -39,6 +39,19 @@ #include <asm/irq.h> #include <asm/uaccess.h> +static int genphy_config_init(struct phy_device *phydev); + +static struct phy_driver genphy_driver = { + .phy_id = 0xffffffff, + .phy_id_mask = 0xffffffff, + .name = "Generic PHY", + .config_init = genphy_config_init, + .features = 0, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + .driver = {.owner = THIS_MODULE, }, +}; + /* get_phy_device * * description: Reads the ID registers of the PHY at addr on the @@ -656,27 +669,32 @@ void phy_driver_unregister(struct phy_driver *drv) } EXPORT_SYMBOL(phy_driver_unregister); -static struct phy_driver genphy_driver = { - .phy_id = 0xffffffff, - .phy_id_mask = 0xffffffff, - .name = "Generic PHY", - .config_init = genphy_config_init, - .features = 0, - .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, - .driver = {.owner = THIS_MODULE, }, -}; -static int __init genphy_init(void) +static int __init phy_init(void) { - return phy_driver_register(&genphy_driver); + int rc; + extern int mdio_bus_init(void); + + rc = phy_driver_register(&genphy_driver); + if (rc) + goto out; + + rc = mdio_bus_init(); + if (rc) + goto out_unreg; + return 0; + +out_unreg: + phy_driver_unregister(&genphy_driver); +out: + return rc; } -static void __exit genphy_exit(void) +static void __exit phy_exit(void) { phy_driver_unregister(&genphy_driver); } -module_init(genphy_init); -module_exit(genphy_exit); +module_init(phy_init); +module_exit(phy_exit); |