diff options
Diffstat (limited to 'drivers/net/igb/e1000_defines.h')
| -rw-r--r-- | drivers/net/igb/e1000_defines.h | 113 |
1 files changed, 0 insertions, 113 deletions
diff --git a/drivers/net/igb/e1000_defines.h b/drivers/net/igb/e1000_defines.h index 79168eeaaa09..5a32a7004e0a 100644 --- a/drivers/net/igb/e1000_defines.h +++ b/drivers/net/igb/e1000_defines.h @@ -42,33 +42,9 @@ #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ -#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ -#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ -#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */ -#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ -#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */ -#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */ -#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */ -#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ - -/* Wake Up Status */ - -/* Wake Up Packet Length */ - -/* Four Flexible Filters are supported */ -#define E1000_FLEXIBLE_FILTER_COUNT_MAX 4 - -/* Each Flexible Filter is at most 128 (0x80) bytes in length */ -#define E1000_FLEXIBLE_FILTER_SIZE_MAX 128 - /* Extended Device Control */ -#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */ -#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */ -#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */ #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */ -#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */ -#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000 #define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000 @@ -103,14 +79,7 @@ #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */ #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ -#define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */ #define E1000_RXD_STAT_TS 0x10000 /* Pkt was time stamped */ -#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ -#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ -#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ -#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ -#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ -#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ #define E1000_RXDEXT_STATERR_CE 0x01000000 #define E1000_RXDEXT_STATERR_SE 0x02000000 @@ -120,14 +89,6 @@ #define E1000_RXDEXT_STATERR_IPE 0x40000000 #define E1000_RXDEXT_STATERR_RXE 0x80000000 -/* mask to determine if packets should be dropped due to frame errors */ -#define E1000_RXD_ERR_FRAME_ERR_MASK ( \ - E1000_RXD_ERR_CE | \ - E1000_RXD_ERR_SE | \ - E1000_RXD_ERR_SEQ | \ - E1000_RXD_ERR_CXE | \ - E1000_RXD_ERR_RXE) - /* Same mask, but for extended and packet split descriptors */ #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ E1000_RXDEXT_STATERR_CE | \ @@ -146,16 +107,11 @@ /* Management Control */ #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ -#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ /* Enable Neighbor Discovery Filtering */ #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ /* Enable MAC address filtering */ #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 -/* Enable MNG packets to host memory */ -#define E1000_MANC_EN_MNG2HOST 0x00200000 -/* Enable IP address filtering */ - /* Receive Control */ #define E1000_RCTL_EN 0x00000002 /* enable */ @@ -163,14 +119,11 @@ #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ #define E1000_RCTL_LPE 0x00000020 /* long packet enable */ -#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ #define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */ #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ -#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */ -#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */ #define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */ #define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */ #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ @@ -227,11 +180,7 @@ /* enable link status from external LINK_0 and LINK_1 pins */ #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ -#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ -#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ -#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */ -#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */ #define E1000_CTRL_RST 0x04000000 /* Global reset */ #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ @@ -309,9 +258,7 @@ #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX /* LED Control */ -#define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F #define E1000_LEDCTL_LED0_MODE_SHIFT 0 -#define E1000_LEDCTL_LED0_IVRT 0x00000040 #define E1000_LEDCTL_LED0_BLINK 0x00000080 #define E1000_LEDCTL_MODE_LED_ON 0xE @@ -358,12 +305,7 @@ #define MAX_JUMBO_FRAME_SIZE 0x3F00 -/* Extended Configuration Control and Size */ -#define E1000_PHY_CTRL_GBE_DISABLE 0x00000040 - /* PBA constants */ -#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */ -#define E1000_PBA_24K 0x0018 #define E1000_PBA_34K 0x0022 #define E1000_PBA_64K 0x0040 /* 64KB */ @@ -379,41 +321,13 @@ /* Interrupt Cause Read */ #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ -#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ #define E1000_ICR_LSC 0x00000004 /* Link Status Change */ #define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */ #define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */ -#define E1000_ICR_RXO 0x00000040 /* rx overrun */ #define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */ -#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */ -#define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */ -#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ -#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ -#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ -#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ -#define E1000_ICR_TXD_LOW 0x00008000 -#define E1000_ICR_SRPD 0x00010000 -#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */ -#define E1000_ICR_MNG 0x00040000 /* Manageability event */ -#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ /* If this bit asserted, the driver should claim the interrupt */ #define E1000_ICR_INT_ASSERTED 0x80000000 -/* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 -/* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 -/* host arb read buffer parity error */ -#define E1000_ICR_HOST_ARB_PAR 0x00400000 -#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ -/* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 -/* queue 1 Tx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 -/* FW changed the status of DISSW bit in the FWSM */ -#define E1000_ICR_DSW 0x00000020 /* LAN connected device generates an interrupt */ -#define E1000_ICR_PHYINT 0x00001000 -#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */ #define E1000_ICR_DOUTSYNC 0x10000000 /* NIC DMA out of sync */ /* Extended Interrupt Cause Read */ @@ -425,7 +339,6 @@ #define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */ #define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */ #define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */ -#define E1000_EICR_TCP_TIMER 0x40000000 /* TCP Timer */ #define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */ /* TCP Timer */ @@ -455,13 +368,11 @@ #define E1000_IMS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ /* Extended Interrupt Mask Set */ -#define E1000_EIMS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */ #define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */ /* Interrupt Cause Set */ #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_ICS_DOUTSYNC E1000_ICR_DOUTSYNC /* NIC DMA out of sync */ /* Extended Interrupt Cause Set */ @@ -497,7 +408,6 @@ #define E1000_ERR_MAC_INIT 5 #define E1000_ERR_RESET 9 #define E1000_ERR_MASTER_REQUESTS_PENDING 10 -#define E1000_ERR_HOST_INTERFACE_COMMAND 11 #define E1000_BLK_PHY_RESET 12 #define E1000_ERR_SWFW_SYNC 13 #define E1000_NOT_IMPLEMENTED 14 @@ -517,30 +427,9 @@ /* Flow Control */ #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ -/* Transmit Configuration Word */ -#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ - -/* Receive Configuration Word */ - -/* PCI Express Control */ -#define E1000_GCR_RXD_NO_SNOOP 0x00000001 -#define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002 -#define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004 -#define E1000_GCR_TXD_NO_SNOOP 0x00000008 -#define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010 -#define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020 - -#define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \ - E1000_GCR_RXDSCW_NO_SNOOP | \ - E1000_GCR_RXDSCR_NO_SNOOP | \ - E1000_GCR_TXD_NO_SNOOP | \ - E1000_GCR_TXDSCW_NO_SNOOP | \ - E1000_GCR_TXDSCR_NO_SNOOP) - /* PHY Control Register */ #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ -#define MII_CR_POWER_DOWN 0x0800 /* Power down */ #define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ #define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ #define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ @@ -670,10 +559,8 @@ #define IGP_LED3_MODE 0x07000000 /* PCI/PCI-X/PCI-EX Config space */ -#define PCI_HEADER_TYPE_REGISTER 0x0E #define PCIE_LINK_STATUS 0x12 -#define PCI_HEADER_TYPE_MULTIFUNC 0x80 #define PCIE_LINK_WIDTH_MASK 0x3F0 #define PCIE_LINK_WIDTH_SHIFT 4 |