diff options
Diffstat (limited to 'drivers/net/ethernet/stmicro/stmmac')
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/common.h | 5 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac1000.h | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 99 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c | 2 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h | 34 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 12 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c | 4 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 42 |
8 files changed, 156 insertions, 44 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index bac0e44d7634..586a33624dd2 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -27,6 +27,7 @@ #include <linux/etherdevice.h> #include <linux/netdevice.h> +#include <linux/stmmac.h> #include <linux/phy.h> #include <linux/module.h> #if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) @@ -378,7 +379,9 @@ struct stmmac_dma_ops { /* DMA core initialization */ int (*reset)(void __iomem *ioaddr); void (*init)(void __iomem *ioaddr, int pbl, int fb, int mb, - int burst_len, u32 dma_tx, u32 dma_rx, int atds); + int aal, u32 dma_tx, u32 dma_rx, int atds); + /* Configure the AXI Bus Mode Register */ + void (*axi)(void __iomem *ioaddr, struct stmmac_axi *axi); /* Dump DMA registers */ void (*dump_regs) (void __iomem *ioaddr); /* Set tx/rx threshold in the csr6 register diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h index 9d36ae788429..b0593a4268ee 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h @@ -240,7 +240,7 @@ enum rx_tx_priority_ratio { #define DMA_BUS_MODE_RPBL_MASK 0x003e0000 /* Rx-Programmable Burst Len */ #define DMA_BUS_MODE_RPBL_SHIFT 17 #define DMA_BUS_MODE_USP 0x00800000 -#define DMA_BUS_MODE_PBL 0x01000000 +#define DMA_BUS_MODE_MAXPBL 0x01000000 #define DMA_BUS_MODE_AAL 0x02000000 /* DMA CRS Control and Status Register Mapping */ diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c index 5f0aea56b298..da32d6037e3e 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c @@ -30,24 +30,76 @@ #include "dwmac1000.h" #include "dwmac_dma.h" +static void dwmac1000_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi) +{ + u32 value = readl(ioaddr + DMA_AXI_BUS_MODE); + int i; + + pr_info("dwmac1000: Master AXI performs %s burst length\n", + !(value & DMA_AXI_UNDEF) ? "fixed" : "any"); + + if (axi->axi_lpi_en) + value |= DMA_AXI_EN_LPI; + if (axi->axi_xit_frm) + value |= DMA_AXI_LPI_XIT_FRM; + + value |= (axi->axi_wr_osr_lmt & DMA_AXI_WR_OSR_LMT_MASK) << + DMA_AXI_WR_OSR_LMT_SHIFT; + + value |= (axi->axi_rd_osr_lmt & DMA_AXI_RD_OSR_LMT_MASK) << + DMA_AXI_RD_OSR_LMT_SHIFT; + + /* Depending on the UNDEF bit the Master AXI will perform any burst + * length according to the BLEN programmed (by default all BLEN are + * set). + */ + for (i = 0; i < AXI_BLEN; i++) { + switch (axi->axi_blen[i]) { + case 256: + value |= DMA_AXI_BLEN256; + break; + case 128: + value |= DMA_AXI_BLEN128; + break; + case 64: + value |= DMA_AXI_BLEN64; + break; + case 32: + value |= DMA_AXI_BLEN32; + break; + case 16: + value |= DMA_AXI_BLEN16; + break; + case 8: + value |= DMA_AXI_BLEN8; + break; + case 4: + value |= DMA_AXI_BLEN4; + break; + } + } + + writel(value, ioaddr + DMA_AXI_BUS_MODE); +} + static void dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb, - int burst_len, u32 dma_tx, u32 dma_rx, int atds) + int aal, u32 dma_tx, u32 dma_rx, int atds) { - u32 value; + u32 value = readl(ioaddr + DMA_BUS_MODE); /* - * Set the DMA PBL (Programmable Burst Length) mode - * Before stmmac core 3.50 this mode bit was 4xPBL, and + * Set the DMA PBL (Programmable Burst Length) mode. + * + * Note: before stmmac core 3.50 this mode bit was 4xPBL, and * post 3.5 mode bit acts as 8*PBL. - * For core rev < 3.5, when the core is set for 4xPBL mode, the - * DMA transfers the data in 4, 8, 16, 32, 64 & 128 beats - * depending on pbl value. - * For core rev > 3.5, when the core is set for 8xPBL mode, the - * DMA transfers the data in 8, 16, 32, 64, 128 & 256 beats - * depending on pbl value. + * + * This configuration doesn't take care about the Separate PBL + * so only the bits: 13-8 are programmed with the PBL passed from the + * platform. */ - value = DMA_BUS_MODE_PBL | ((pbl << DMA_BUS_MODE_PBL_SHIFT) | - (pbl << DMA_BUS_MODE_RPBL_SHIFT)); + value |= DMA_BUS_MODE_MAXPBL; + value &= ~DMA_BUS_MODE_PBL_MASK; + value |= (pbl << DMA_BUS_MODE_PBL_SHIFT); /* Set the Fixed burst mode */ if (fb) @@ -60,26 +112,10 @@ static void dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb, if (atds) value |= DMA_BUS_MODE_ATDS; - writel(value, ioaddr + DMA_BUS_MODE); + if (aal) + value |= DMA_BUS_MODE_AAL; - /* In case of GMAC AXI configuration, program the DMA_AXI_BUS_MODE - * for supported bursts. - * - * Note: This is applicable only for revision GMACv3.61a. For - * older version this register is reserved and shall have no - * effect. - * - * Note: - * For Fixed Burst Mode: if we directly write 0xFF to this - * register using the configurations pass from platform code, - * this would ensure that all bursts supported by core are set - * and those which are not supported would remain ineffective. - * - * For Non Fixed Burst Mode: provide the maximum value of the - * burst length. Any burst equal or below the provided burst - * length would be allowed to perform. - */ - writel(burst_len, ioaddr + DMA_AXI_BUS_MODE); + writel(value, ioaddr + DMA_BUS_MODE); /* Mask interrupts by writing to CSR7 */ writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA); @@ -192,6 +228,7 @@ static void dwmac1000_rx_watchdog(void __iomem *ioaddr, u32 riwt) const struct stmmac_dma_ops dwmac1000_dma_ops = { .reset = dwmac_dma_reset, .init = dwmac1000_dma_init, + .axi = dwmac1000_dma_axi, .dump_regs = dwmac1000_dump_dma_regs, .dma_mode = dwmac1000_dma_operation_mode, .enable_dma_transmission = dwmac_enable_dma_transmission, diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c index c40582a938a4..61f54c99a7de 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c @@ -33,7 +33,7 @@ #include "dwmac_dma.h" static void dwmac100_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb, - int burst_len, u32 dma_tx, u32 dma_rx, int atds) + int aal, u32 dma_tx, u32 dma_rx, int atds) { /* Enable Application Access by writing to DMA CSR0 */ writel(DMA_BUS_MODE_DEFAULT | (pbl << DMA_BUS_MODE_PBL_SHIFT), diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h index 13ca90e23479..726d9d9aaf83 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac_dma.h @@ -41,8 +41,40 @@ /* Rx watchdog register */ #define DMA_RX_WATCHDOG 0x00001024 -/* AXI Bus Mode */ + +/* AXI Master Bus Mode */ #define DMA_AXI_BUS_MODE 0x00001028 + +#define DMA_AXI_EN_LPI BIT(31) +#define DMA_AXI_LPI_XIT_FRM BIT(30) +#define DMA_AXI_WR_OSR_LMT GENMASK(23, 20) +#define DMA_AXI_WR_OSR_LMT_SHIFT 20 +#define DMA_AXI_WR_OSR_LMT_MASK 0xf +#define DMA_AXI_RD_OSR_LMT GENMASK(19, 16) +#define DMA_AXI_RD_OSR_LMT_SHIFT 16 +#define DMA_AXI_RD_OSR_LMT_MASK 0xf + +#define DMA_AXI_OSR_MAX 0xf +#define DMA_AXI_MAX_OSR_LIMIT ((DMA_AXI_OSR_MAX << DMA_AXI_WR_OSR_LMT_SHIFT) | \ + (DMA_AXI_OSR_MAX << DMA_AXI_RD_OSR_LMT_SHIFT)) +#define DMA_AXI_1KBBE BIT(13) +#define DMA_AXI_AAL BIT(12) +#define DMA_AXI_BLEN256 BIT(7) +#define DMA_AXI_BLEN128 BIT(6) +#define DMA_AXI_BLEN64 BIT(5) +#define DMA_AXI_BLEN32 BIT(4) +#define DMA_AXI_BLEN16 BIT(3) +#define DMA_AXI_BLEN8 BIT(2) +#define DMA_AXI_BLEN4 BIT(1) +#define DMA_BURST_LEN_DEFAULT (DMA_AXI_BLEN256 | DMA_AXI_BLEN128 | \ + DMA_AXI_BLEN64 | DMA_AXI_BLEN32 | \ + DMA_AXI_BLEN16 | DMA_AXI_BLEN8 | \ + DMA_AXI_BLEN4) + +#define DMA_AXI_UNDEF BIT(0) + +#define DMA_AXI_BURST_LEN_MASK 0x000000FE + #define DMA_CUR_TX_BUF_ADDR 0x00001050 /* Current Host Tx Buffer */ #define DMA_CUR_RX_BUF_ADDR 0x00001054 /* Current Host Rx Buffer */ #define DMA_HW_FEATURE 0x00001058 /* HW Feature Register */ diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 13752e933e43..89c26268822e 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1635,7 +1635,7 @@ static void stmmac_check_ether_addr(struct stmmac_priv *priv) */ static int stmmac_init_dma_engine(struct stmmac_priv *priv) { - int pbl = DEFAULT_DMA_PBL, fixed_burst = 0, burst_len = 0; + int pbl = DEFAULT_DMA_PBL, fixed_burst = 0, aal = 0; int mixed_burst = 0; int atds = 0; int ret = 0; @@ -1644,7 +1644,7 @@ static int stmmac_init_dma_engine(struct stmmac_priv *priv) pbl = priv->plat->dma_cfg->pbl; fixed_burst = priv->plat->dma_cfg->fixed_burst; mixed_burst = priv->plat->dma_cfg->mixed_burst; - burst_len = priv->plat->dma_cfg->burst_len; + aal = priv->plat->dma_cfg->aal; } if (priv->extend_desc && (priv->mode == STMMAC_RING_MODE)) @@ -1657,8 +1657,12 @@ static int stmmac_init_dma_engine(struct stmmac_priv *priv) } priv->hw->dma->init(priv->ioaddr, pbl, fixed_burst, mixed_burst, - burst_len, priv->dma_tx_phy, - priv->dma_rx_phy, atds); + aal, priv->dma_tx_phy, priv->dma_rx_phy, atds); + + if ((priv->synopsys_id >= DWMAC_CORE_3_50) && + (priv->plat->axi && priv->hw->dma->axi)) + priv->hw->dma->axi(priv->ioaddr, priv->plat->axi); + return ret; } diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c index d71a721ea61c..ae4388735b7f 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c @@ -81,7 +81,7 @@ static void stmmac_default_data(struct plat_stmmacenet_data *plat) plat->mdio_bus_data->phy_mask = 0; plat->dma_cfg->pbl = 32; - plat->dma_cfg->burst_len = DMA_AXI_BLEN_256; + /* TODO: AXI */ /* Set default value for multicast hash bins */ plat->multicast_filter_bins = HASH_TABLE_SIZE; @@ -115,8 +115,8 @@ static int quark_default_data(struct plat_stmmacenet_data *plat, plat->mdio_bus_data->phy_mask = 0; plat->dma_cfg->pbl = 16; - plat->dma_cfg->burst_len = DMA_AXI_BLEN_256; plat->dma_cfg->fixed_burst = 1; + /* AXI (TODO) */ /* Set default value for multicast hash bins */ plat->multicast_filter_bins = HASH_TABLE_SIZE; diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c index 6a52fa18cbf2..69ccf486d4fa 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c @@ -96,6 +96,42 @@ static int dwmac1000_validate_ucast_entries(int ucast_entries) } /** + * stmmac_axi_setup - parse DT parameters for programming the AXI register + * @pdev: platform device + * @priv: driver private struct. + * Description: + * if required, from device-tree the AXI internal register can be tuned + * by using platform parameters. + */ +static struct stmmac_axi *stmmac_axi_setup(struct platform_device *pdev) +{ + struct device_node *np; + struct stmmac_axi *axi; + + np = of_parse_phandle(pdev->dev.of_node, "snps,axi-config", 0); + if (!np) + return NULL; + + axi = kzalloc(sizeof(axi), GFP_KERNEL); + if (!axi) + return ERR_PTR(-ENOMEM); + + axi->axi_lpi_en = of_property_read_bool(np, "snps,lpi_en"); + axi->axi_xit_frm = of_property_read_bool(np, "snps,xit_frm"); + axi->axi_kbbe = of_property_read_bool(np, "snps,axi_kbbe"); + axi->axi_axi_all = of_property_read_bool(np, "snps,axi_all"); + axi->axi_fb = of_property_read_bool(np, "snps,axi_fb"); + axi->axi_mb = of_property_read_bool(np, "snps,axi_mb"); + axi->axi_rb = of_property_read_bool(np, "snps,axi_rb"); + + of_property_read_u32(np, "snps,wr_osr_lmt", &axi->axi_wr_osr_lmt); + of_property_read_u32(np, "snps,rd_osr_lmt", &axi->axi_rd_osr_lmt); + of_property_read_u32_array(np, "snps,blen", axi->axi_blen, AXI_BLEN); + + return axi; +} + +/** * stmmac_probe_config_dt - parse device-tree driver parameters * @pdev: platform_device structure * @plat: driver data platform structure @@ -216,13 +252,11 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) } plat->dma_cfg = dma_cfg; of_property_read_u32(np, "snps,pbl", &dma_cfg->pbl); + dma_cfg->aal = of_property_read_bool(np, "snps,aal"); dma_cfg->fixed_burst = of_property_read_bool(np, "snps,fixed-burst"); dma_cfg->mixed_burst = of_property_read_bool(np, "snps,mixed-burst"); - of_property_read_u32(np, "snps,burst_len", &dma_cfg->burst_len); - if (dma_cfg->burst_len < 0 || dma_cfg->burst_len > 256) - dma_cfg->burst_len = 0; } plat->force_thresh_dma_mode = of_property_read_bool(np, "snps,force_thresh_dma_mode"); if (plat->force_thresh_dma_mode) { @@ -230,6 +264,8 @@ stmmac_probe_config_dt(struct platform_device *pdev, const char **mac) pr_warn("force_sf_dma_mode is ignored if force_thresh_dma_mode is set."); } + plat->axi = stmmac_axi_setup(pdev); + return plat; } #else |