diff options
Diffstat (limited to 'drivers/net/ethernet/stmicro/stmmac')
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/Kconfig | 14 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/Makefile | 1 | ||||
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 365 |
3 files changed, 380 insertions, 0 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig index 731e0453a7d4..cec147d1d34f 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig @@ -16,6 +16,7 @@ if STMMAC_ETH config STMMAC_PLATFORM tristate "STMMAC Platform bus support" depends on STMMAC_ETH + select MFD_SYSCON default y ---help--- This selects the platform specific bus support for the stmmac driver. @@ -36,6 +37,19 @@ config DWMAC_GENERIC platform specific code to function or is using platform data for setup. +config DWMAC_IPQ806X + tristate "QCA IPQ806x DWMAC support" + default ARCH_QCOM + depends on OF + select MFD_SYSCON + help + Support for QCA IPQ806X DWMAC Ethernet. + + This selects the IPQ806x SoC glue layer support for the stmmac + device driver. This driver does not use any of the hardware + acceleration features available on this SoC. Network devices + will behave like standard non-accelerated ethernet interfaces. + config DWMAC_LPC18XX tristate "NXP LPC18xx/43xx DWMAC support" default ARCH_LPC18XX diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile index 92e714a48367..b3901616f4f6 100644 --- a/drivers/net/ethernet/stmicro/stmmac/Makefile +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile @@ -6,6 +6,7 @@ stmmac-objs:= stmmac_main.o stmmac_ethtool.o stmmac_mdio.o ring_mode.o \ # Ordering matters. Generic driver must be last. obj-$(CONFIG_STMMAC_PLATFORM) += stmmac-platform.o +obj-$(CONFIG_DWMAC_IPQ806X) += dwmac-ipq806x.o obj-$(CONFIG_DWMAC_LPC18XX) += dwmac-lpc18xx.o obj-$(CONFIG_DWMAC_MESON) += dwmac-meson.o obj-$(CONFIG_DWMAC_ROCKCHIP) += dwmac-rk.o diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c new file mode 100644 index 000000000000..7e3129e7f143 --- /dev/null +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c @@ -0,0 +1,365 @@ +/* + * Qualcomm Atheros IPQ806x GMAC glue layer + * + * Copyright (C) 2015 The Linux Foundation + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/phy.h> +#include <linux/regmap.h> +#include <linux/clk.h> +#include <linux/reset.h> +#include <linux/of_net.h> +#include <linux/mfd/syscon.h> +#include <linux/stmmac.h> +#include <linux/of_mdio.h> +#include <linux/module.h> + +#include "stmmac_platform.h" + +#define NSS_COMMON_CLK_GATE 0x8 +#define NSS_COMMON_CLK_GATE_PTP_EN(x) BIT(0x10 + x) +#define NSS_COMMON_CLK_GATE_RGMII_RX_EN(x) BIT(0x9 + (x * 2)) +#define NSS_COMMON_CLK_GATE_RGMII_TX_EN(x) BIT(0x8 + (x * 2)) +#define NSS_COMMON_CLK_GATE_GMII_RX_EN(x) BIT(0x4 + x) +#define NSS_COMMON_CLK_GATE_GMII_TX_EN(x) BIT(0x0 + x) + +#define NSS_COMMON_CLK_DIV0 0xC +#define NSS_COMMON_CLK_DIV_OFFSET(x) (x * 8) +#define NSS_COMMON_CLK_DIV_MASK 0x7f + +#define NSS_COMMON_CLK_SRC_CTRL 0x14 +#define NSS_COMMON_CLK_SRC_CTRL_OFFSET(x) (1 << x) +/* Mode is coded on 1 bit but is different depending on the MAC ID: + * MAC0: QSGMII=0 RGMII=1 + * MAC1: QSGMII=0 SGMII=0 RGMII=1 + * MAC2 & MAC3: QSGMII=0 SGMII=1 + */ +#define NSS_COMMON_CLK_SRC_CTRL_RGMII(x) 1 +#define NSS_COMMON_CLK_SRC_CTRL_SGMII(x) ((x >= 2) ? 1 : 0) + +#define NSS_COMMON_MACSEC_CTL 0x28 +#define NSS_COMMON_MACSEC_CTL_EXT_BYPASS_EN(x) (1 << x) + +#define NSS_COMMON_GMAC_CTL(x) (0x30 + (x * 4)) +#define NSS_COMMON_GMAC_CTL_CSYS_REQ BIT(19) +#define NSS_COMMON_GMAC_CTL_PHY_IFACE_SEL BIT(16) +#define NSS_COMMON_GMAC_CTL_IFG_LIMIT_OFFSET 8 +#define NSS_COMMON_GMAC_CTL_IFG_OFFSET 0 +#define NSS_COMMON_GMAC_CTL_IFG_MASK 0x3f + +#define NSS_COMMON_CLK_DIV_RGMII_1000 1 +#define NSS_COMMON_CLK_DIV_RGMII_100 9 +#define NSS_COMMON_CLK_DIV_RGMII_10 99 +#define NSS_COMMON_CLK_DIV_SGMII_1000 0 +#define NSS_COMMON_CLK_DIV_SGMII_100 4 +#define NSS_COMMON_CLK_DIV_SGMII_10 49 + +#define QSGMII_PCS_MODE_CTL 0x68 +#define QSGMII_PCS_MODE_CTL_AUTONEG_EN(x) BIT((x * 8) + 7) + +#define QSGMII_PCS_CAL_LCKDT_CTL 0x120 +#define QSGMII_PCS_CAL_LCKDT_CTL_RST BIT(19) + +/* Only GMAC1/2/3 support SGMII and their CTL register are not contiguous */ +#define QSGMII_PHY_SGMII_CTL(x) ((x == 1) ? 0x134 : \ + (0x13c + (4 * (x - 2)))) +#define QSGMII_PHY_CDR_EN BIT(0) +#define QSGMII_PHY_RX_FRONT_EN BIT(1) +#define QSGMII_PHY_RX_SIGNAL_DETECT_EN BIT(2) +#define QSGMII_PHY_TX_DRIVER_EN BIT(3) +#define QSGMII_PHY_QSGMII_EN BIT(7) +#define QSGMII_PHY_PHASE_LOOP_GAIN_OFFSET 12 +#define QSGMII_PHY_PHASE_LOOP_GAIN_MASK 0x7 +#define QSGMII_PHY_RX_DC_BIAS_OFFSET 18 +#define QSGMII_PHY_RX_DC_BIAS_MASK 0x3 +#define QSGMII_PHY_RX_INPUT_EQU_OFFSET 20 +#define QSGMII_PHY_RX_INPUT_EQU_MASK 0x3 +#define QSGMII_PHY_CDR_PI_SLEW_OFFSET 22 +#define QSGMII_PHY_CDR_PI_SLEW_MASK 0x3 +#define QSGMII_PHY_TX_DRV_AMP_OFFSET 28 +#define QSGMII_PHY_TX_DRV_AMP_MASK 0xf + +struct ipq806x_gmac { + struct platform_device *pdev; + struct regmap *nss_common; + struct regmap *qsgmii_csr; + uint32_t id; + struct clk *core_clk; + phy_interface_t phy_mode; +}; + +static int get_clk_div_sgmii(struct ipq806x_gmac *gmac, unsigned int speed) +{ + struct device *dev = &gmac->pdev->dev; + int div; + + switch (speed) { + case SPEED_1000: + div = NSS_COMMON_CLK_DIV_SGMII_1000; + break; + + case SPEED_100: + div = NSS_COMMON_CLK_DIV_SGMII_100; + break; + + case SPEED_10: + div = NSS_COMMON_CLK_DIV_SGMII_10; + break; + + default: + dev_err(dev, "Speed %dMbps not supported in SGMII\n", speed); + return -EINVAL; + } + + return div; +} + +static int get_clk_div_rgmii(struct ipq806x_gmac *gmac, unsigned int speed) +{ + struct device *dev = &gmac->pdev->dev; + int div; + + switch (speed) { + case SPEED_1000: + div = NSS_COMMON_CLK_DIV_RGMII_1000; + break; + + case SPEED_100: + div = NSS_COMMON_CLK_DIV_RGMII_100; + break; + + case SPEED_10: + div = NSS_COMMON_CLK_DIV_RGMII_10; + break; + + default: + dev_err(dev, "Speed %dMbps not supported in RGMII\n", speed); + return -EINVAL; + } + + return div; +} + +static int ipq806x_gmac_set_speed(struct ipq806x_gmac *gmac, unsigned int speed) +{ + uint32_t clk_bits, val; + int div; + + switch (gmac->phy_mode) { + case PHY_INTERFACE_MODE_RGMII: + div = get_clk_div_rgmii(gmac, speed); + clk_bits = NSS_COMMON_CLK_GATE_RGMII_RX_EN(gmac->id) | + NSS_COMMON_CLK_GATE_RGMII_TX_EN(gmac->id); + break; + + case PHY_INTERFACE_MODE_SGMII: + div = get_clk_div_sgmii(gmac, speed); + clk_bits = NSS_COMMON_CLK_GATE_GMII_RX_EN(gmac->id) | + NSS_COMMON_CLK_GATE_GMII_TX_EN(gmac->id); + break; + + default: + dev_err(&gmac->pdev->dev, "Unsupported PHY mode: \"%s\"\n", + phy_modes(gmac->phy_mode)); + return -EINVAL; + } + + /* Disable the clocks */ + regmap_read(gmac->nss_common, NSS_COMMON_CLK_GATE, &val); + val &= ~clk_bits; + regmap_write(gmac->nss_common, NSS_COMMON_CLK_GATE, val); + + /* Set the divider */ + regmap_read(gmac->nss_common, NSS_COMMON_CLK_DIV0, &val); + val &= ~(NSS_COMMON_CLK_DIV_MASK + << NSS_COMMON_CLK_DIV_OFFSET(gmac->id)); + val |= div << NSS_COMMON_CLK_DIV_OFFSET(gmac->id); + regmap_write(gmac->nss_common, NSS_COMMON_CLK_DIV0, val); + + /* Enable the clock back */ + regmap_read(gmac->nss_common, NSS_COMMON_CLK_GATE, &val); + val |= clk_bits; + regmap_write(gmac->nss_common, NSS_COMMON_CLK_GATE, val); + + return 0; +} + +static void *ipq806x_gmac_of_parse(struct ipq806x_gmac *gmac) +{ + struct device *dev = &gmac->pdev->dev; + + gmac->phy_mode = of_get_phy_mode(dev->of_node); + if (gmac->phy_mode < 0) { + dev_err(dev, "missing phy mode property\n"); + return ERR_PTR(-EINVAL); + } + + if (of_property_read_u32(dev->of_node, "qcom,id", &gmac->id) < 0) { + dev_err(dev, "missing qcom id property\n"); + return ERR_PTR(-EINVAL); + } + + /* The GMACs are called 1 to 4 in the documentation, but to simplify the + * code and keep it consistent with the Linux convention, we'll number + * them from 0 to 3 here. + */ + if (gmac->id < 0 || gmac->id > 3) { + dev_err(dev, "invalid gmac id\n"); + return ERR_PTR(-EINVAL); + } + + gmac->core_clk = devm_clk_get(dev, "stmmaceth"); + if (IS_ERR(gmac->core_clk)) { + dev_err(dev, "missing stmmaceth clk property\n"); + return gmac->core_clk; + } + clk_set_rate(gmac->core_clk, 266000000); + + /* Setup the register map for the nss common registers */ + gmac->nss_common = syscon_regmap_lookup_by_phandle(dev->of_node, + "qcom,nss-common"); + if (IS_ERR(gmac->nss_common)) { + dev_err(dev, "missing nss-common node\n"); + return gmac->nss_common; + } + + /* Setup the register map for the qsgmii csr registers */ + gmac->qsgmii_csr = syscon_regmap_lookup_by_phandle(dev->of_node, + "qcom,qsgmii-csr"); + if (IS_ERR(gmac->qsgmii_csr)) { + dev_err(dev, "missing qsgmii-csr node\n"); + return gmac->qsgmii_csr; + } + + return NULL; +} + +static void *ipq806x_gmac_setup(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct ipq806x_gmac *gmac; + int val; + void *err; + + gmac = devm_kzalloc(dev, sizeof(*gmac), GFP_KERNEL); + if (!gmac) + return ERR_PTR(-ENOMEM); + + gmac->pdev = pdev; + + err = ipq806x_gmac_of_parse(gmac); + if (err) { + dev_err(dev, "device tree parsing error\n"); + return err; + } + + regmap_write(gmac->qsgmii_csr, QSGMII_PCS_CAL_LCKDT_CTL, + QSGMII_PCS_CAL_LCKDT_CTL_RST); + + /* Inter frame gap is set to 12 */ + val = 12 << NSS_COMMON_GMAC_CTL_IFG_OFFSET | + 12 << NSS_COMMON_GMAC_CTL_IFG_LIMIT_OFFSET; + /* We also initiate an AXI low power exit request */ + val |= NSS_COMMON_GMAC_CTL_CSYS_REQ; + switch (gmac->phy_mode) { + case PHY_INTERFACE_MODE_RGMII: + val |= NSS_COMMON_GMAC_CTL_PHY_IFACE_SEL; + break; + case PHY_INTERFACE_MODE_SGMII: + val &= ~NSS_COMMON_GMAC_CTL_PHY_IFACE_SEL; + break; + default: + dev_err(&pdev->dev, "Unsupported PHY mode: \"%s\"\n", + phy_modes(gmac->phy_mode)); + return NULL; + } + regmap_write(gmac->nss_common, NSS_COMMON_GMAC_CTL(gmac->id), val); + + /* Configure the clock src according to the mode */ + regmap_read(gmac->nss_common, NSS_COMMON_CLK_SRC_CTRL, &val); + val &= ~NSS_COMMON_CLK_SRC_CTRL_OFFSET(gmac->id); + switch (gmac->phy_mode) { + case PHY_INTERFACE_MODE_RGMII: + val |= NSS_COMMON_CLK_SRC_CTRL_RGMII(gmac->id) << + NSS_COMMON_CLK_SRC_CTRL_OFFSET(gmac->id); + break; + case PHY_INTERFACE_MODE_SGMII: + val |= NSS_COMMON_CLK_SRC_CTRL_SGMII(gmac->id) << + NSS_COMMON_CLK_SRC_CTRL_OFFSET(gmac->id); + break; + default: + dev_err(&pdev->dev, "Unsupported PHY mode: \"%s\"\n", + phy_modes(gmac->phy_mode)); + return NULL; + } + regmap_write(gmac->nss_common, NSS_COMMON_CLK_SRC_CTRL, val); + + /* Enable PTP clock */ + regmap_read(gmac->nss_common, NSS_COMMON_CLK_GATE, &val); + val |= NSS_COMMON_CLK_GATE_PTP_EN(gmac->id); + regmap_write(gmac->nss_common, NSS_COMMON_CLK_GATE, val); + + if (gmac->phy_mode == PHY_INTERFACE_MODE_SGMII) { + regmap_write(gmac->qsgmii_csr, QSGMII_PHY_SGMII_CTL(gmac->id), + QSGMII_PHY_CDR_EN | + QSGMII_PHY_RX_FRONT_EN | + QSGMII_PHY_RX_SIGNAL_DETECT_EN | + QSGMII_PHY_TX_DRIVER_EN | + QSGMII_PHY_QSGMII_EN | + 0x4 << QSGMII_PHY_PHASE_LOOP_GAIN_OFFSET | + 0x3 << QSGMII_PHY_RX_DC_BIAS_OFFSET | + 0x1 << QSGMII_PHY_RX_INPUT_EQU_OFFSET | + 0x2 << QSGMII_PHY_CDR_PI_SLEW_OFFSET | + 0xC << QSGMII_PHY_TX_DRV_AMP_OFFSET); + } + + return gmac; +} + +static void ipq806x_gmac_fix_mac_speed(void *priv, unsigned int speed) +{ + struct ipq806x_gmac *gmac = priv; + + ipq806x_gmac_set_speed(gmac, speed); +} + +static const struct stmmac_of_data ipq806x_gmac_data = { + .has_gmac = 1, + .setup = ipq806x_gmac_setup, + .fix_mac_speed = ipq806x_gmac_fix_mac_speed, +}; + +static const struct of_device_id ipq806x_gmac_dwmac_match[] = { + { .compatible = "qcom,ipq806x-gmac", .data = &ipq806x_gmac_data }, + { } +}; +MODULE_DEVICE_TABLE(of, ipq806x_gmac_dwmac_match); + +static struct platform_driver ipq806x_gmac_dwmac_driver = { + .probe = stmmac_pltfr_probe, + .remove = stmmac_pltfr_remove, + .driver = { + .name = "ipq806x-gmac-dwmac", + .pm = &stmmac_pltfr_pm_ops, + .of_match_table = ipq806x_gmac_dwmac_match, + }, +}; +module_platform_driver(ipq806x_gmac_dwmac_driver); + +MODULE_AUTHOR("Mathieu Olivari <mathieu@codeaurora.org>"); +MODULE_DESCRIPTION("Qualcomm Atheros IPQ806x DWMAC specific glue layer"); +MODULE_LICENSE("Dual BSD/GPL"); |