diff options
Diffstat (limited to 'drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c')
| -rw-r--r-- | drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c | 31 |
1 files changed, 19 insertions, 12 deletions
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c index bf83c03bfd06..2c431b616058 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c @@ -30,8 +30,8 @@ #include "dwmac1000.h" #include "dwmac_dma.h" -static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, - int mb, int burst_len, u32 dma_tx, u32 dma_rx) +static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb, + int burst_len, u32 dma_tx, u32 dma_rx, int atds) { u32 value = readl(ioaddr + DMA_BUS_MODE); int limit; @@ -60,7 +60,7 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, * depending on pbl value. */ value = DMA_BUS_MODE_PBL | ((pbl << DMA_BUS_MODE_PBL_SHIFT) | - (pbl << DMA_BUS_MODE_RPBL_SHIFT)); + (pbl << DMA_BUS_MODE_RPBL_SHIFT)); /* Set the Fixed burst mode */ if (fb) @@ -73,6 +73,10 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, #ifdef CONFIG_STMMAC_DA value |= DMA_BUS_MODE_DA; /* Rx has priority over tx */ #endif + + if (atds) + value |= DMA_BUS_MODE_ATDS; + writel(value, ioaddr + DMA_BUS_MODE); /* In case of GMAC AXI configuration, program the DMA_AXI_BUS_MODE @@ -90,14 +94,16 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, * * For Non Fixed Burst Mode: provide the maximum value of the * burst length. Any burst equal or below the provided burst - * length would be allowed to perform. */ + * length would be allowed to perform. + */ writel(burst_len, ioaddr + DMA_AXI_BUS_MODE); /* Mask interrupts by writing to CSR7 */ writel(DMA_INTR_DEFAULT_MASK, ioaddr + DMA_INTR_ENA); - /* The base address of the RX/TX descriptor lists must be written into - * DMA CSR3 and CSR4, respectively. */ + /* RX/TX descriptor base address lists must be written into + * DMA CSR3 and CSR4, respectively + */ writel(dma_tx, ioaddr + DMA_TX_BASE_ADDR); writel(dma_rx, ioaddr + DMA_RCV_BASE_ADDR); @@ -105,7 +111,7 @@ static int dwmac1000_dma_init(void __iomem *ioaddr, int pbl, int fb, } static void dwmac1000_dma_operation_mode(void __iomem *ioaddr, int txmode, - int rxmode) + int rxmode) { u32 csr6 = readl(ioaddr + DMA_CONTROL); @@ -114,11 +120,12 @@ static void dwmac1000_dma_operation_mode(void __iomem *ioaddr, int txmode, /* Transmit COE type 2 cannot be done in cut-through mode. */ csr6 |= DMA_CONTROL_TSF; /* Operating on second frame increase the performance - * especially when transmit store-and-forward is used.*/ + * especially when transmit store-and-forward is used. + */ csr6 |= DMA_CONTROL_OSF; } else { - CHIP_DBG(KERN_DEBUG "GMAC: disabling TX store and forward mode" - " (threshold = %d)\n", txmode); + CHIP_DBG(KERN_DEBUG "GMAC: disabling TX SF (threshold %d)\n", + txmode); csr6 &= ~DMA_CONTROL_TSF; csr6 &= DMA_CONTROL_TC_TX_MASK; /* Set the transmit threshold */ @@ -138,8 +145,8 @@ static void dwmac1000_dma_operation_mode(void __iomem *ioaddr, int txmode, CHIP_DBG(KERN_DEBUG "GMAC: enable RX store and forward mode\n"); csr6 |= DMA_CONTROL_RSF; } else { - CHIP_DBG(KERN_DEBUG "GMAC: disabling RX store and forward mode" - " (threshold = %d)\n", rxmode); + CHIP_DBG(KERN_DEBUG "GMAC: disable RX SF mode (threshold %d)\n", + rxmode); csr6 &= ~DMA_CONTROL_RSF; csr6 &= DMA_CONTROL_TC_RX_MASK; if (rxmode <= 32) |