diff options
Diffstat (limited to 'drivers/net/ethernet/broadcom')
-rw-r--r-- | drivers/net/ethernet/broadcom/Kconfig | 2 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/b44.c | 2 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/bcmsysport.c | 31 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 4 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h | 7 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 74 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h | 5 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 149 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/cnic.c | 4 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/genet/bcmgenet.c | 143 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/tg3.c | 36 | ||||
-rw-r--r-- | drivers/net/ethernet/broadcom/tg3.h | 1 |
12 files changed, 239 insertions, 219 deletions
diff --git a/drivers/net/ethernet/broadcom/Kconfig b/drivers/net/ethernet/broadcom/Kconfig index 7dcfb19a31c8..d8d07a818b89 100644 --- a/drivers/net/ethernet/broadcom/Kconfig +++ b/drivers/net/ethernet/broadcom/Kconfig @@ -84,7 +84,7 @@ config BNX2 config CNIC tristate "QLogic CNIC support" - depends on PCI + depends on PCI && (IPV6 || IPV6=n) select BNX2 select UIO ---help--- diff --git a/drivers/net/ethernet/broadcom/b44.c b/drivers/net/ethernet/broadcom/b44.c index 4a7028d65912..d588136b23b9 100644 --- a/drivers/net/ethernet/broadcom/b44.c +++ b/drivers/net/ethernet/broadcom/b44.c @@ -1697,7 +1697,7 @@ static struct rtnl_link_stats64 *b44_get_stats64(struct net_device *dev, hwstat->tx_underruns + hwstat->tx_excessive_cols + hwstat->tx_late_cols); - nstat->multicast = hwstat->tx_multicast_pkts; + nstat->multicast = hwstat->rx_multicast_pkts; nstat->collisions = hwstat->tx_total_cols; nstat->rx_length_errors = (hwstat->rx_oversize_pkts + diff --git a/drivers/net/ethernet/broadcom/bcmsysport.c b/drivers/net/ethernet/broadcom/bcmsysport.c index 6f4e18644bd4..d9b9170ed2fc 100644 --- a/drivers/net/ethernet/broadcom/bcmsysport.c +++ b/drivers/net/ethernet/broadcom/bcmsysport.c @@ -534,6 +534,25 @@ static unsigned int bcm_sysport_desc_rx(struct bcm_sysport_priv *priv, while ((processed < to_process) && (processed < budget)) { cb = &priv->rx_cbs[priv->rx_read_ptr]; skb = cb->skb; + + processed++; + priv->rx_read_ptr++; + + if (priv->rx_read_ptr == priv->num_rx_bds) + priv->rx_read_ptr = 0; + + /* We do not have a backing SKB, so we do not a corresponding + * DMA mapping for this incoming packet since + * bcm_sysport_rx_refill always either has both skb and mapping + * or none. + */ + if (unlikely(!skb)) { + netif_err(priv, rx_err, ndev, "out of memory!\n"); + ndev->stats.rx_dropped++; + ndev->stats.rx_errors++; + goto refill; + } + dma_unmap_single(kdev, dma_unmap_addr(cb, dma_addr), RX_BUF_LENGTH, DMA_FROM_DEVICE); @@ -543,23 +562,11 @@ static unsigned int bcm_sysport_desc_rx(struct bcm_sysport_priv *priv, status = (rsb->rx_status_len >> DESC_STATUS_SHIFT) & DESC_STATUS_MASK; - processed++; - priv->rx_read_ptr++; - if (priv->rx_read_ptr == priv->num_rx_bds) - priv->rx_read_ptr = 0; - netif_dbg(priv, rx_status, ndev, "p=%d, c=%d, rd_ptr=%d, len=%d, flag=0x%04x\n", p_index, priv->rx_c_index, priv->rx_read_ptr, len, status); - if (unlikely(!skb)) { - netif_err(priv, rx_err, ndev, "out of memory!\n"); - ndev->stats.rx_dropped++; - ndev->stats.rx_errors++; - goto refill; - } - if (unlikely(!(status & DESC_EOP) || !(status & DESC_SOP))) { netif_err(priv, rx_status, ndev, "fragmented packet!\n"); ndev->stats.rx_dropped++; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c index 4e6c82e20224..4ccc806b1150 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c @@ -483,11 +483,7 @@ static void bnx2x_tpa_start(struct bnx2x_fastpath *fp, u16 queue, #ifdef BNX2X_STOP_ON_ERROR fp->tpa_queue_used |= (1 << queue); -#ifdef _ASM_GENERIC_INT_L64_H - DP(NETIF_MSG_RX_STATUS, "fp->tpa_queue_used = 0x%lx\n", -#else DP(NETIF_MSG_RX_STATUS, "fp->tpa_queue_used = 0x%llx\n", -#endif fp->tpa_queue_used); #endif } diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h index 5ba8af50c84f..c4daa068f1db 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h @@ -2233,7 +2233,12 @@ struct shmem2_region { u32 reserved3; /* Offset 0x14C */ u32 reserved4; /* Offset 0x150 */ u32 link_attr_sync[PORT_MAX]; /* Offset 0x154 */ - #define LINK_ATTR_SYNC_KR2_ENABLE (1<<0) + #define LINK_ATTR_SYNC_KR2_ENABLE 0x00000001 + #define LINK_SFP_EEPROM_COMP_CODE_MASK 0x0000ff00 + #define LINK_SFP_EEPROM_COMP_CODE_SHIFT 8 + #define LINK_SFP_EEPROM_COMP_CODE_SR 0x00001000 + #define LINK_SFP_EEPROM_COMP_CODE_LR 0x00002000 + #define LINK_SFP_EEPROM_COMP_CODE_LRM 0x00004000 u32 reserved5[2]; u32 reserved6[PORT_MAX]; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index 53fb4fa61b40..549549eaf580 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -154,15 +154,22 @@ typedef int (*read_sfp_module_eeprom_func_p)(struct bnx2x_phy *phy, LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE) #define SFP_EEPROM_CON_TYPE_ADDR 0x2 + #define SFP_EEPROM_CON_TYPE_VAL_UNKNOWN 0x0 #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7 #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21 #define SFP_EEPROM_CON_TYPE_VAL_RJ45 0x22 -#define SFP_EEPROM_COMP_CODE_ADDR 0x3 - #define SFP_EEPROM_COMP_CODE_SR_MASK (1<<4) - #define SFP_EEPROM_COMP_CODE_LR_MASK (1<<5) - #define SFP_EEPROM_COMP_CODE_LRM_MASK (1<<6) +#define SFP_EEPROM_10G_COMP_CODE_ADDR 0x3 + #define SFP_EEPROM_10G_COMP_CODE_SR_MASK (1<<4) + #define SFP_EEPROM_10G_COMP_CODE_LR_MASK (1<<5) + #define SFP_EEPROM_10G_COMP_CODE_LRM_MASK (1<<6) + +#define SFP_EEPROM_1G_COMP_CODE_ADDR 0x6 + #define SFP_EEPROM_1G_COMP_CODE_SX (1<<0) + #define SFP_EEPROM_1G_COMP_CODE_LX (1<<1) + #define SFP_EEPROM_1G_COMP_CODE_CX (1<<2) + #define SFP_EEPROM_1G_COMP_CODE_BASE_T (1<<3) #define SFP_EEPROM_FC_TX_TECH_ADDR 0x8 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4 @@ -3633,8 +3640,8 @@ static void bnx2x_warpcore_enable_AN_KR2(struct bnx2x_phy *phy, reg_set[i].val); /* Start KR2 work-around timer which handles BCM8073 link-parner */ - vars->link_attr_sync |= LINK_ATTR_SYNC_KR2_ENABLE; - bnx2x_update_link_attr(params, vars->link_attr_sync); + params->link_attr_sync |= LINK_ATTR_SYNC_KR2_ENABLE; + bnx2x_update_link_attr(params, params->link_attr_sync); } static void bnx2x_disable_kr2(struct link_params *params, @@ -3666,8 +3673,8 @@ static void bnx2x_disable_kr2(struct link_params *params, for (i = 0; i < ARRAY_SIZE(reg_set); i++) bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, reg_set[i].val); - vars->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE; - bnx2x_update_link_attr(params, vars->link_attr_sync); + params->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE; + bnx2x_update_link_attr(params, params->link_attr_sync); vars->check_kr2_recovery_cnt = CHECK_KR2_RECOVERY_CNT; } @@ -4810,7 +4817,7 @@ void bnx2x_link_status_update(struct link_params *params, ~FEATURE_CONFIG_PFC_ENABLED; if (SHMEM2_HAS(bp, link_attr_sync)) - vars->link_attr_sync = SHMEM2_RD(bp, + params->link_attr_sync = SHMEM2_RD(bp, link_attr_sync[params->port]); DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x int_mask 0x%x\n", @@ -8057,21 +8064,24 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; u32 sync_offset = 0, phy_idx, media_types; - u8 gport, val[2], check_limiting_mode = 0; + u8 val[SFP_EEPROM_FC_TX_TECH_ADDR + 1], check_limiting_mode = 0; *edc_mode = EDC_MODE_LIMITING; phy->media_type = ETH_PHY_UNSPECIFIED; /* First check for copper cable */ if (bnx2x_read_sfp_module_eeprom(phy, params, I2C_DEV_ADDR_A0, - SFP_EEPROM_CON_TYPE_ADDR, - 2, + 0, + SFP_EEPROM_FC_TX_TECH_ADDR + 1, (u8 *)val) != 0) { DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n"); return -EINVAL; } - - switch (val[0]) { + params->link_attr_sync &= ~LINK_SFP_EEPROM_COMP_CODE_MASK; + params->link_attr_sync |= val[SFP_EEPROM_10G_COMP_CODE_ADDR] << + LINK_SFP_EEPROM_COMP_CODE_SHIFT; + bnx2x_update_link_attr(params, params->link_attr_sync); + switch (val[SFP_EEPROM_CON_TYPE_ADDR]) { case SFP_EEPROM_CON_TYPE_VAL_COPPER: { u8 copper_module_type; @@ -8079,17 +8089,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, /* Check if its active cable (includes SFP+ module) * of passive cable */ - if (bnx2x_read_sfp_module_eeprom(phy, - params, - I2C_DEV_ADDR_A0, - SFP_EEPROM_FC_TX_TECH_ADDR, - 1, - &copper_module_type) != 0) { - DP(NETIF_MSG_LINK, - "Failed to read copper-cable-type" - " from SFP+ EEPROM\n"); - return -EINVAL; - } + copper_module_type = val[SFP_EEPROM_FC_TX_TECH_ADDR]; if (copper_module_type & SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) { @@ -8115,16 +8115,18 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, } break; } + case SFP_EEPROM_CON_TYPE_VAL_UNKNOWN: case SFP_EEPROM_CON_TYPE_VAL_LC: case SFP_EEPROM_CON_TYPE_VAL_RJ45: check_limiting_mode = 1; - if ((val[1] & (SFP_EEPROM_COMP_CODE_SR_MASK | - SFP_EEPROM_COMP_CODE_LR_MASK | - SFP_EEPROM_COMP_CODE_LRM_MASK)) == 0) { + if ((val[SFP_EEPROM_10G_COMP_CODE_ADDR] & + (SFP_EEPROM_10G_COMP_CODE_SR_MASK | + SFP_EEPROM_10G_COMP_CODE_LR_MASK | + SFP_EEPROM_10G_COMP_CODE_LRM_MASK)) == 0) { DP(NETIF_MSG_LINK, "1G SFP module detected\n"); - gport = params->port; phy->media_type = ETH_PHY_SFP_1G_FIBER; if (phy->req_line_speed != SPEED_1000) { + u8 gport = params->port; phy->req_line_speed = SPEED_1000; if (!CHIP_IS_E1x(bp)) { gport = BP_PATH(bp) + @@ -8134,6 +8136,12 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, "Warning: Link speed was forced to 1000Mbps. Current SFP module in port %d is not compliant with 10G Ethernet\n", gport); } + if (val[SFP_EEPROM_1G_COMP_CODE_ADDR] & + SFP_EEPROM_1G_COMP_CODE_BASE_T) { + bnx2x_sfp_set_transmitter(params, phy, 0); + msleep(40); + bnx2x_sfp_set_transmitter(params, phy, 1); + } } else { int idx, cfg_idx = 0; DP(NETIF_MSG_LINK, "10G Optic module detected\n"); @@ -8149,7 +8157,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, break; default: DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n", - val[0]); + val[SFP_EEPROM_CON_TYPE_ADDR]); return -EINVAL; } sync_offset = params->shmem_base + @@ -13507,7 +13515,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, sigdet = bnx2x_warpcore_get_sigdet(phy, params); if (!sigdet) { - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { bnx2x_kr2_recovery(params, vars, phy); DP(NETIF_MSG_LINK, "No sigdet\n"); } @@ -13525,7 +13533,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, /* CL73 has not begun yet */ if (base_page == 0) { - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { bnx2x_kr2_recovery(params, vars, phy); DP(NETIF_MSG_LINK, "No BP\n"); } @@ -13541,7 +13549,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, ((next_page & 0xe0) == 0x20)))); /* In case KR2 is already disabled, check if we need to re-enable it */ - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { if (!not_kr2_device) { DP(NETIF_MSG_LINK, "BP=0x%x, NP=0x%x\n", base_page, next_page); diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h index 389f5f8cb0a3..d9cce4c3899b 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h @@ -323,6 +323,9 @@ struct link_params { #define LINK_FLAGS_INT_DISABLED (1<<0) #define PHY_INITIALIZED (1<<1) u32 lfa_base; + + /* The same definitions as the shmem2 parameter */ + u32 link_attr_sync; }; /* Output parameters */ @@ -364,8 +367,6 @@ struct link_vars { u8 rx_tx_asic_rst; u8 turn_to_run_wc_rt; u16 rsrv2; - /* The same definitions as the shmem2 parameter */ - u32 link_attr_sync; }; /***********************************************************/ diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c index c13364b6cc19..d1c093dcb054 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c @@ -6849,6 +6849,37 @@ static void bnx2x__common_init_phy(struct bnx2x *bp) bnx2x_release_phy_lock(bp); } +static void bnx2x_config_endianity(struct bnx2x *bp, u32 val) +{ + REG_WR(bp, PXP2_REG_RQ_QM_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_TM_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_SRC_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_CDU_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_DBG_ENDIAN_M, val); + + /* make sure this value is 0 */ + REG_WR(bp, PXP2_REG_RQ_HC_ENDIAN_M, 0); + + REG_WR(bp, PXP2_REG_RD_QM_SWAP_MODE, val); + REG_WR(bp, PXP2_REG_RD_TM_SWAP_MODE, val); + REG_WR(bp, PXP2_REG_RD_SRC_SWAP_MODE, val); + REG_WR(bp, PXP2_REG_RD_CDURD_SWAP_MODE, val); +} + +static void bnx2x_set_endianity(struct bnx2x *bp) +{ +#ifdef __BIG_ENDIAN + bnx2x_config_endianity(bp, 1); +#else + bnx2x_config_endianity(bp, 0); +#endif +} + +static void bnx2x_reset_endianity(struct bnx2x *bp) +{ + bnx2x_config_endianity(bp, 0); +} + /** * bnx2x_init_hw_common - initialize the HW at the COMMON phase. * @@ -6915,23 +6946,7 @@ static int bnx2x_init_hw_common(struct bnx2x *bp) bnx2x_init_block(bp, BLOCK_PXP2, PHASE_COMMON); bnx2x_init_pxp(bp); - -#ifdef __BIG_ENDIAN - REG_WR(bp, PXP2_REG_RQ_QM_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_TM_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_SRC_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_CDU_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_DBG_ENDIAN_M, 1); - /* make sure this value is 0 */ - REG_WR(bp, PXP2_REG_RQ_HC_ENDIAN_M, 0); - -/* REG_WR(bp, PXP2_REG_RD_PBF_SWAP_MODE, 1); */ - REG_WR(bp, PXP2_REG_RD_QM_SWAP_MODE, 1); - REG_WR(bp, PXP2_REG_RD_TM_SWAP_MODE, 1); - REG_WR(bp, PXP2_REG_RD_SRC_SWAP_MODE, 1); - REG_WR(bp, PXP2_REG_RD_CDURD_SWAP_MODE, 1); -#endif - + bnx2x_set_endianity(bp); bnx2x_ilt_init_page_size(bp, INITOP_SET); if (CHIP_REV_IS_FPGA(bp) && CHIP_IS_E1H(bp)) @@ -10052,6 +10067,8 @@ static void bnx2x_prev_unload_close_mac(struct bnx2x *bp, } #define BNX2X_PREV_UNDI_PROD_ADDR(p) (BAR_TSTRORM_INTMEM + 0x1508 + ((p) << 4)) +#define BNX2X_PREV_UNDI_PROD_ADDR_H(f) (BAR_TSTRORM_INTMEM + \ + 0x1848 + ((f) << 4)) #define BNX2X_PREV_UNDI_RCQ(val) ((val) & 0xffff) #define BNX2X_PREV_UNDI_BD(val) ((val) >> 16 & 0xffff) #define BNX2X_PREV_UNDI_PROD(rcq, bd) ((bd) << 16 | (rcq)) @@ -10059,8 +10076,6 @@ static void bnx2x_prev_unload_close_mac(struct bnx2x *bp, #define BCM_5710_UNDI_FW_MF_MAJOR (0x07) #define BCM_5710_UNDI_FW_MF_MINOR (0x08) #define BCM_5710_UNDI_FW_MF_VERS (0x05) -#define BNX2X_PREV_UNDI_MF_PORT(p) (BAR_TSTRORM_INTMEM + 0x150c + ((p) << 4)) -#define BNX2X_PREV_UNDI_MF_FUNC(f) (BAR_TSTRORM_INTMEM + 0x184c + ((f) << 4)) static bool bnx2x_prev_is_after_undi(struct bnx2x *bp) { @@ -10079,72 +10094,25 @@ static bool bnx2x_prev_is_after_undi(struct bnx2x *bp) return false; } -static bool bnx2x_prev_unload_undi_fw_supports_mf(struct bnx2x *bp) -{ - u8 major, minor, version; - u32 fw; - - /* Must check that FW is loaded */ - if (!(REG_RD(bp, MISC_REG_RESET_REG_1) & - MISC_REGISTERS_RESET_REG_1_RST_XSEM)) { - BNX2X_DEV_INFO("XSEM is reset - UNDI MF FW is not loaded\n"); - return false; - } - - /* Read Currently loaded FW version */ - fw = REG_RD(bp, XSEM_REG_PRAM); - major = fw & 0xff; - minor = (fw >> 0x8) & 0xff; - version = (fw >> 0x10) & 0xff; - BNX2X_DEV_INFO("Loaded FW: 0x%08x: Major 0x%02x Minor 0x%02x Version 0x%02x\n", - fw, major, minor, version); - - if (major > BCM_5710_UNDI_FW_MF_MAJOR) - return true; - - if ((major == BCM_5710_UNDI_FW_MF_MAJOR) && - (minor > BCM_5710_UNDI_FW_MF_MINOR)) - return true; - - if ((major == BCM_5710_UNDI_FW_MF_MAJOR) && - (minor == BCM_5710_UNDI_FW_MF_MINOR) && - (version >= BCM_5710_UNDI_FW_MF_VERS)) - return true; - - return false; -} - -static void bnx2x_prev_unload_undi_mf(struct bnx2x *bp) -{ - int i; - - /* Due to legacy (FW) code, the first function on each engine has a - * different offset macro from the rest of the functions. - * Setting this for all 8 functions is harmless regardless of whether - * this is actually a multi-function device. - */ - for (i = 0; i < 2; i++) - REG_WR(bp, BNX2X_PREV_UNDI_MF_PORT(i), 1); - - for (i = 2; i < 8; i++) - REG_WR(bp, BNX2X_PREV_UNDI_MF_FUNC(i - 2), 1); - - BNX2X_DEV_INFO("UNDI FW (MF) set to discard\n"); -} - -static void bnx2x_prev_unload_undi_inc(struct bnx2x *bp, u8 port, u8 inc) +static void bnx2x_prev_unload_undi_inc(struct bnx2x *bp, u8 inc) { u16 rcq, bd; - u32 tmp_reg = REG_RD(bp, BNX2X_PREV_UNDI_PROD_ADDR(port)); + u32 addr, tmp_reg; + + if (BP_FUNC(bp) < 2) + addr = BNX2X_PREV_UNDI_PROD_ADDR(BP_PORT(bp)); + else + addr = BNX2X_PREV_UNDI_PROD_ADDR_H(BP_FUNC(bp) - 2); + tmp_reg = REG_RD(bp, addr); rcq = BNX2X_PREV_UNDI_RCQ(tmp_reg) + inc; bd = BNX2X_PREV_UNDI_BD(tmp_reg) + inc; tmp_reg = BNX2X_PREV_UNDI_PROD(rcq, bd); - REG_WR(bp, BNX2X_PREV_UNDI_PROD_ADDR(port), tmp_reg); + REG_WR(bp, addr, tmp_reg); - BNX2X_DEV_INFO("UNDI producer [%d] rings bd -> 0x%04x, rcq -> 0x%04x\n", - port, bd, rcq); + BNX2X_DEV_INFO("UNDI producer [%d/%d][%08x] rings bd -> 0x%04x, rcq -> 0x%04x\n", + BP_PORT(bp), BP_FUNC(bp), addr, bd, rcq); } static int bnx2x_prev_mcp_done(struct bnx2x *bp) @@ -10383,7 +10351,6 @@ static int bnx2x_prev_unload_common(struct bnx2x *bp) /* Reset should be performed after BRB is emptied */ if (reset_reg & MISC_REGISTERS_RESET_REG_1_RST_BRB1) { u32 timer_count = 1000; - bool need_write = true; /* Close the MAC Rx to prevent BRB from filling up */ bnx2x_prev_unload_close_mac(bp, &mac_vals); @@ -10420,20 +10387,10 @@ static int bnx2x_prev_unload_common(struct bnx2x *bp) else timer_count--; - /* New UNDI FW supports MF and contains better - * cleaning methods - might be redundant but harmless. - */ - if (bnx2x_prev_unload_undi_fw_supports_mf(bp)) { - if (need_write) { - bnx2x_prev_unload_undi_mf(bp); - need_write = false; - } - } else if (prev_undi) { - /* If UNDI resides in memory, - * manually increment it - */ - bnx2x_prev_unload_undi_inc(bp, BP_PORT(bp), 1); - } + /* If UNDI resides in memory, manually increment it */ + if (prev_undi) + bnx2x_prev_unload_undi_inc(bp, 1); + udelay(10); } @@ -13227,9 +13184,15 @@ static void __bnx2x_remove(struct pci_dev *pdev, bnx2x_iov_remove_one(bp); /* Power on: we can't let PCI layer write to us while we are in D3 */ - if (IS_PF(bp)) + if (IS_PF(bp)) { bnx2x_set_power_state(bp, PCI_D0); + /* Set endianity registers to reset values in case next driver + * boots in different endianty environment. + */ + bnx2x_reset_endianity(bp); + } + /* Disable MSI/MSI-X */ bnx2x_disable_msi(bp); diff --git a/drivers/net/ethernet/broadcom/cnic.c b/drivers/net/ethernet/broadcom/cnic.c index 27861a6c7ca5..a6a9f284c8dd 100644 --- a/drivers/net/ethernet/broadcom/cnic.c +++ b/drivers/net/ethernet/broadcom/cnic.c @@ -31,7 +31,7 @@ #include <linux/if_vlan.h> #include <linux/prefetch.h> #include <linux/random.h> -#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) +#if IS_ENABLED(CONFIG_VLAN_8021Q) #define BCM_VLAN 1 #endif #include <net/ip.h> @@ -3685,7 +3685,7 @@ static int cnic_get_v4_route(struct sockaddr_in *dst_addr, static int cnic_get_v6_route(struct sockaddr_in6 *dst_addr, struct dst_entry **dst) { -#if defined(CONFIG_IPV6) || (defined(CONFIG_IPV6_MODULE) && defined(MODULE)) +#if IS_ENABLED(CONFIG_IPV6) struct flowi6 fl6; memset(&fl6, 0, sizeof(fl6)); diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index 3f9d4de8173c..5cc9cae21ed5 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -875,6 +875,7 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, int last_tx_cn, last_c_index, num_tx_bds; struct enet_cb *tx_cb_ptr; struct netdev_queue *txq; + unsigned int bds_compl; unsigned int c_index; /* Compute how many buffers are transmitted since last xmit call */ @@ -899,7 +900,9 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, /* Reclaim transmitted buffers */ while (last_tx_cn-- > 0) { tx_cb_ptr = ring->cbs + last_c_index; + bds_compl = 0; if (tx_cb_ptr->skb) { + bds_compl = skb_shinfo(tx_cb_ptr->skb)->nr_frags + 1; dev->stats.tx_bytes += tx_cb_ptr->skb->len; dma_unmap_single(&dev->dev, dma_unmap_addr(tx_cb_ptr, dma_addr), @@ -916,7 +919,7 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, dma_unmap_addr_set(tx_cb_ptr, dma_addr, 0); } dev->stats.tx_packets++; - ring->free_bds += 1; + ring->free_bds += bds_compl; last_c_index++; last_c_index &= (num_tx_bds - 1); @@ -1274,12 +1277,29 @@ static unsigned int bcmgenet_desc_rx(struct bcmgenet_priv *priv, while ((rxpktprocessed < rxpkttoprocess) && (rxpktprocessed < budget)) { + cb = &priv->rx_cbs[priv->rx_read_ptr]; + skb = cb->skb; + + rxpktprocessed++; + + priv->rx_read_ptr++; + priv->rx_read_ptr &= (priv->num_rx_bds - 1); + + /* We do not have a backing SKB, so we do not have a + * corresponding DMA mapping for this incoming packet since + * bcmgenet_rx_refill always either has both skb and mapping or + * none. + */ + if (unlikely(!skb)) { + dev->stats.rx_dropped++; + dev->stats.rx_errors++; + goto refill; + } + /* Unmap the packet contents such that we can use the * RSV from the 64 bytes descriptor when enabled and save * a 32-bits register read */ - cb = &priv->rx_cbs[priv->rx_read_ptr]; - skb = cb->skb; dma_unmap_single(&dev->dev, dma_unmap_addr(cb, dma_addr), priv->rx_buf_len, DMA_FROM_DEVICE); @@ -1307,18 +1327,6 @@ static unsigned int bcmgenet_desc_rx(struct bcmgenet_priv *priv, __func__, p_index, priv->rx_c_index, priv->rx_read_ptr, dma_length_status); - rxpktprocessed++; - - priv->rx_read_ptr++; - priv->rx_read_ptr &= (priv->num_rx_bds - 1); - - /* out of memory, just drop packets at the hardware level */ - if (unlikely(!skb)) { - dev->stats.rx_dropped++; - dev->stats.rx_errors++; - goto refill; - } - if (unlikely(!(dma_flag & DMA_EOP) || !(dma_flag & DMA_SOP))) { netif_err(priv, rx_status, dev, "dropping fragmented packet!\n"); @@ -1736,13 +1744,63 @@ static void bcmgenet_init_multiq(struct net_device *dev) bcmgenet_tdma_writel(priv, reg, DMA_CTRL); } +static int bcmgenet_dma_teardown(struct bcmgenet_priv *priv) +{ + int ret = 0; + int timeout = 0; + u32 reg; + + /* Disable TDMA to stop add more frames in TX DMA */ + reg = bcmgenet_tdma_readl(priv, DMA_CTRL); + reg &= ~DMA_EN; + bcmgenet_tdma_writel(priv, reg, DMA_CTRL); + + /* Check TDMA status register to confirm TDMA is disabled */ + while (timeout++ < DMA_TIMEOUT_VAL) { + reg = bcmgenet_tdma_readl(priv, DMA_STATUS); + if (reg & DMA_DISABLED) + break; + + udelay(1); + } + + if (timeout == DMA_TIMEOUT_VAL) { + netdev_warn(priv->dev, "Timed out while disabling TX DMA\n"); + ret = -ETIMEDOUT; + } + + /* Wait 10ms for packet drain in both tx and rx dma */ + usleep_range(10000, 20000); + + /* Disable RDMA */ + reg = bcmgenet_rdma_readl(priv, DMA_CTRL); + reg &= ~DMA_EN; + bcmgenet_rdma_writel(priv, reg, DMA_CTRL); + + timeout = 0; + /* Check RDMA status register to confirm RDMA is disabled */ + while (timeout++ < DMA_TIMEOUT_VAL) { + reg = bcmgenet_rdma_readl(priv, DMA_STATUS); + if (reg & DMA_DISABLED) + break; + + udelay(1); + } + + if (timeout == DMA_TIMEOUT_VAL) { + netdev_warn(priv->dev, "Timed out while disabling RX DMA\n"); + ret = -ETIMEDOUT; + } + + return ret; +} + static void bcmgenet_fini_dma(struct bcmgenet_priv *priv) { int i; /* disable DMA */ - bcmgenet_rdma_writel(priv, 0, DMA_CTRL); - bcmgenet_tdma_writel(priv, 0, DMA_CTRL); + bcmgenet_dma_teardown(priv); for (i = 0; i < priv->num_tx_bds; i++) { if (priv->tx_cbs[i].skb != NULL) { @@ -2101,57 +2159,6 @@ err_clk_disable: return ret; } -static int bcmgenet_dma_teardown(struct bcmgenet_priv *priv) -{ - int ret = 0; - int timeout = 0; - u32 reg; - - /* Disable TDMA to stop add more frames in TX DMA */ - reg = bcmgenet_tdma_readl(priv, DMA_CTRL); - reg &= ~DMA_EN; - bcmgenet_tdma_writel(priv, reg, DMA_CTRL); - - /* Check TDMA status register to confirm TDMA is disabled */ - while (timeout++ < DMA_TIMEOUT_VAL) { - reg = bcmgenet_tdma_readl(priv, DMA_STATUS); - if (reg & DMA_DISABLED) - break; - - udelay(1); - } - - if (timeout == DMA_TIMEOUT_VAL) { - netdev_warn(priv->dev, "Timed out while disabling TX DMA\n"); - ret = -ETIMEDOUT; - } - - /* Wait 10ms for packet drain in both tx and rx dma */ - usleep_range(10000, 20000); - - /* Disable RDMA */ - reg = bcmgenet_rdma_readl(priv, DMA_CTRL); - reg &= ~DMA_EN; - bcmgenet_rdma_writel(priv, reg, DMA_CTRL); - - timeout = 0; - /* Check RDMA status register to confirm RDMA is disabled */ - while (timeout++ < DMA_TIMEOUT_VAL) { - reg = bcmgenet_rdma_readl(priv, DMA_STATUS); - if (reg & DMA_DISABLED) - break; - - udelay(1); - } - - if (timeout == DMA_TIMEOUT_VAL) { - netdev_warn(priv->dev, "Timed out while disabling RX DMA\n"); - ret = -ETIMEDOUT; - } - - return ret; -} - static void bcmgenet_netif_stop(struct net_device *dev) { struct bcmgenet_priv *priv = netdev_priv(dev); diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 3ac5d23454a8..e7d3a620d96a 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -7914,8 +7914,6 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, struct net_device *dev) entry = tnapi->tx_prod; base_flags = 0; - if (skb->ip_summed == CHECKSUM_PARTIAL) - base_flags |= TXD_FLAG_TCPUDP_CSUM; mss = skb_shinfo(skb)->gso_size; if (mss) { @@ -7929,6 +7927,13 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, struct net_device *dev) hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb) - ETH_HLEN; + /* HW/FW can not correctly segment packets that have been + * vlan encapsulated. + */ + if (skb->protocol == htons(ETH_P_8021Q) || + skb->protocol == htons(ETH_P_8021AD)) + return tg3_tso_bug(tp, tnapi, txq, skb); + if (!skb_is_gso_v6(skb)) { if (unlikely((ETH_HLEN + hdr_len) > 80) && tg3_flag(tp, TSO_BUG)) @@ -7979,6 +7984,17 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, struct net_device *dev) base_flags |= tsflags << 12; } } + } else if (skb->ip_summed == CHECKSUM_PARTIAL) { + /* HW/FW can not correctly checksum packets that have been + * vlan encapsulated. + */ + if (skb->protocol == htons(ETH_P_8021Q) || + skb->protocol == htons(ETH_P_8021AD)) { + if (skb_checksum_help(skb)) + goto drop; + } else { + base_flags |= TXD_FLAG_TCPUDP_CSUM; + } } if (tg3_flag(tp, USE_JUMBO_BDFLAG) && @@ -11617,6 +11633,12 @@ static int tg3_open(struct net_device *dev) struct tg3 *tp = netdev_priv(dev); int err; + if (tp->pcierr_recovery) { + netdev_err(dev, "Failed to open device. PCI error recovery " + "in progress\n"); + return -EAGAIN; + } + if (tp->fw_needed) { err = tg3_request_firmware(tp); if (tg3_asic_rev(tp) == ASIC_REV_57766) { @@ -11674,6 +11696,12 @@ static int tg3_close(struct net_device *dev) { struct tg3 *tp = netdev_priv(dev); + if (tp->pcierr_recovery) { + netdev_err(dev, "Failed to close device. PCI error recovery " + "in progress\n"); + return -EAGAIN; + } + tg3_ptp_fini(tp); tg3_stop(tp); @@ -17561,6 +17589,7 @@ static int tg3_init_one(struct pci_dev *pdev, tp->rx_mode = TG3_DEF_RX_MODE; tp->tx_mode = TG3_DEF_TX_MODE; tp->irq_sync = 1; + tp->pcierr_recovery = false; if (tg3_debug > 0) tp->msg_enable = tg3_debug; @@ -18071,6 +18100,8 @@ static pci_ers_result_t tg3_io_error_detected(struct pci_dev *pdev, rtnl_lock(); + tp->pcierr_recovery = true; + /* We probably don't have netdev yet */ if (!netdev || !netif_running(netdev)) goto done; @@ -18195,6 +18226,7 @@ static void tg3_io_resume(struct pci_dev *pdev) tg3_phy_start(tp); done: + tp->pcierr_recovery = false; rtnl_unlock(); } diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h index 461accaf0aa4..31c9f8295953 100644 --- a/drivers/net/ethernet/broadcom/tg3.h +++ b/drivers/net/ethernet/broadcom/tg3.h @@ -3407,6 +3407,7 @@ struct tg3 { struct device *hwmon_dev; bool link_up; + bool pcierr_recovery; }; /* Accessor macros for chip and asic attributes |