summaryrefslogtreecommitdiffstats
path: root/drivers/net/can/Kconfig
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/can/Kconfig')
-rw-r--r--drivers/net/can/Kconfig30
1 files changed, 15 insertions, 15 deletions
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index 17c166cc8482..f07012a76c0c 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -3,7 +3,7 @@ menu "CAN Device Drivers"
config CAN_VCAN
tristate "Virtual Local CAN Interface (vcan)"
- ---help---
+ help
Similar to the network loopback devices, vcan offers a
virtual local CAN interface.
@@ -12,7 +12,7 @@ config CAN_VCAN
config CAN_VXCAN
tristate "Virtual CAN Tunnel (vxcan)"
- ---help---
+ help
Similar to the virtual ethernet driver veth, vxcan implements a
local CAN traffic tunnel between two virtual CAN network devices.
When creating a vxcan, two vxcan devices are created as pair.
@@ -31,7 +31,7 @@ config CAN_VXCAN
config CAN_SLCAN
tristate "Serial / USB serial CAN Adaptors (slcan)"
depends on TTY
- ---help---
+ help
CAN driver for several 'low cost' CAN interfaces that are attached
via serial lines or via USB-to-serial adapters using the LAWICEL
ASCII protocol. The driver implements the tty linediscipline N_SLCAN.
@@ -51,7 +51,7 @@ config CAN_SLCAN
config CAN_DEV
tristate "Platform CAN drivers with Netlink support"
default y
- ---help---
+ help
Enables the common framework for platform CAN drivers with Netlink
support. This is the standard library for CAN drivers.
If unsure, say Y.
@@ -61,7 +61,7 @@ if CAN_DEV
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
default y
- ---help---
+ help
If enabled, CAN bit-timing parameters will be calculated for the
bit-rate specified via Netlink argument "bitrate" when the device
get started. This works fine for the most common CAN controllers
@@ -81,7 +81,7 @@ config CAN_LEDS
# fulfills your needs instead of fixing this driver.
depends on BROKEN
select LEDS_TRIGGERS
- ---help---
+ help
This option adds two LED triggers for packet receive and transmit
events on each supported CAN device.
@@ -91,20 +91,20 @@ config CAN_LEDS
config CAN_AT91
tristate "Atmel AT91 onchip CAN controller"
depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM
- ---help---
+ help
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
and AT91SAM9X5 processors.
config CAN_FLEXCAN
tristate "Support for Freescale FLEXCAN based chips"
depends on OF && HAS_IOMEM
- ---help---
+ help
Say Y here if you want to support for Freescale FlexCAN.
config CAN_GRCAN
tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
depends on OF && HAS_DMA
- ---help---
+ help
Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN.
Note that the driver supports little endian, even though little
endian syntheses of the cores would need some modifications on
@@ -113,7 +113,7 @@ config CAN_GRCAN
config CAN_JANZ_ICAN3
tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
depends on MFD_JANZ_CMODIO
- ---help---
+ help
Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
connects to a MODULbus carrier board.
@@ -136,7 +136,7 @@ config CAN_KVASER_PCIEFD
config CAN_SUN4I
tristate "Allwinner A10 CAN controller"
depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST
- ---help---
+ help
Say Y here if you want to use CAN controller found on Allwinner
A10/A20 SoCs.
@@ -146,7 +146,7 @@ config CAN_SUN4I
config CAN_TI_HECC
depends on ARM
tristate "TI High End CAN Controller"
- ---help---
+ help
Driver for TI HECC (High End CAN Controller) module found on many
TI devices. The device specifications are available from www.ti.com
@@ -154,14 +154,14 @@ config CAN_XILINXCAN
tristate "Xilinx CAN"
depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST
depends on COMMON_CLK && HAS_IOMEM
- ---help---
+ help
Xilinx CAN driver. This driver supports both soft AXI CAN IP and
Zynq CANPS IP.
config PCH_CAN
tristate "Intel EG20T PCH CAN controller"
depends on PCI && (X86_32 || COMPILE_TEST)
- ---help---
+ help
This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
is an IOH for x86 embedded processor (Intel Atom E6xx series).
This driver can access CAN bus.
@@ -182,7 +182,7 @@ endif
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"
- ---help---
+ help
Say Y here if you want the CAN device drivers to produce a bunch of
debug messages to the system log. Select this if you are having
a problem with CAN support and want to see more of what is going