diff options
Diffstat (limited to 'drivers/mtd/spi-nor')
-rw-r--r-- | drivers/mtd/spi-nor/controllers/Kconfig | 10 | ||||
-rw-r--r-- | drivers/mtd/spi-nor/controllers/Makefile | 1 | ||||
-rw-r--r-- | drivers/mtd/spi-nor/controllers/aspeed-smc.c | 921 |
3 files changed, 0 insertions, 932 deletions
diff --git a/drivers/mtd/spi-nor/controllers/Kconfig b/drivers/mtd/spi-nor/controllers/Kconfig index 50f4f3484d42..ca45dcd3ffe8 100644 --- a/drivers/mtd/spi-nor/controllers/Kconfig +++ b/drivers/mtd/spi-nor/controllers/Kconfig @@ -1,14 +1,4 @@ # SPDX-License-Identifier: GPL-2.0-only -config SPI_ASPEED_SMC - tristate "Aspeed flash controllers in SPI mode" - depends on ARCH_ASPEED || COMPILE_TEST - depends on HAS_IOMEM && OF - help - This enables support for the Firmware Memory controller (FMC) - in the Aspeed AST2500/AST2400 SoCs when attached to SPI NOR chips, - and support for the SPI flash memory controller (SPI) for - the host firmware. The implementation only supports SPI NOR. - config SPI_HISI_SFC tristate "Hisilicon FMC SPI NOR Flash Controller(SFC)" depends on ARCH_HISI || COMPILE_TEST diff --git a/drivers/mtd/spi-nor/controllers/Makefile b/drivers/mtd/spi-nor/controllers/Makefile index 6e2a1dc68466..0b8e1d530913 100644 --- a/drivers/mtd/spi-nor/controllers/Makefile +++ b/drivers/mtd/spi-nor/controllers/Makefile @@ -1,4 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 -obj-$(CONFIG_SPI_ASPEED_SMC) += aspeed-smc.o obj-$(CONFIG_SPI_HISI_SFC) += hisi-sfc.o obj-$(CONFIG_SPI_NXP_SPIFI) += nxp-spifi.o diff --git a/drivers/mtd/spi-nor/controllers/aspeed-smc.c b/drivers/mtd/spi-nor/controllers/aspeed-smc.c deleted file mode 100644 index acfe010f9dd7..000000000000 --- a/drivers/mtd/spi-nor/controllers/aspeed-smc.c +++ /dev/null @@ -1,921 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later -/* - * ASPEED Static Memory Controller driver - * - * Copyright (c) 2015-2016, IBM Corporation. - */ - -#include <linux/bug.h> -#include <linux/device.h> -#include <linux/io.h> -#include <linux/module.h> -#include <linux/mutex.h> -#include <linux/mtd/mtd.h> -#include <linux/mtd/partitions.h> -#include <linux/mtd/spi-nor.h> -#include <linux/of.h> -#include <linux/of_platform.h> -#include <linux/sizes.h> -#include <linux/sysfs.h> - -#define DEVICE_NAME "aspeed-smc" - -/* - * The driver only support SPI flash - */ -enum aspeed_smc_flash_type { - smc_type_nor = 0, - smc_type_nand = 1, - smc_type_spi = 2, -}; - -struct aspeed_smc_chip; - -struct aspeed_smc_info { - u32 maxsize; /* maximum size of chip window */ - u8 nce; /* number of chip enables */ - bool hastype; /* flash type field exists in config reg */ - u8 we0; /* shift for write enable bit for CE0 */ - u8 ctl0; /* offset in regs of ctl for CE0 */ - - void (*set_4b)(struct aspeed_smc_chip *chip); -}; - -static void aspeed_smc_chip_set_4b_spi_2400(struct aspeed_smc_chip *chip); -static void aspeed_smc_chip_set_4b(struct aspeed_smc_chip *chip); - -static const struct aspeed_smc_info fmc_2400_info = { - .maxsize = 64 * 1024 * 1024, - .nce = 5, - .hastype = true, - .we0 = 16, - .ctl0 = 0x10, - .set_4b = aspeed_smc_chip_set_4b, -}; - -static const struct aspeed_smc_info spi_2400_info = { - .maxsize = 64 * 1024 * 1024, - .nce = 1, - .hastype = false, - .we0 = 0, - .ctl0 = 0x04, - .set_4b = aspeed_smc_chip_set_4b_spi_2400, -}; - -static const struct aspeed_smc_info fmc_2500_info = { - .maxsize = 256 * 1024 * 1024, - .nce = 3, - .hastype = true, - .we0 = 16, - .ctl0 = 0x10, - .set_4b = aspeed_smc_chip_set_4b, -}; - -static const struct aspeed_smc_info spi_2500_info = { - .maxsize = 128 * 1024 * 1024, - .nce = 2, - .hastype = false, - .we0 = 16, - .ctl0 = 0x10, - .set_4b = aspeed_smc_chip_set_4b, -}; - -enum aspeed_smc_ctl_reg_value { - smc_base, /* base value without mode for other commands */ - smc_read, /* command reg for (maybe fast) reads */ - smc_write, /* command reg for writes */ - smc_max, -}; - -struct aspeed_smc_controller; - -struct aspeed_smc_chip { - int cs; - struct aspeed_smc_controller *controller; - void __iomem *ctl; /* control register */ - void __iomem *ahb_base; /* base of chip window */ - u32 ahb_window_size; /* chip mapping window size */ - u32 ctl_val[smc_max]; /* control settings */ - enum aspeed_smc_flash_type type; /* what type of flash */ - struct spi_nor nor; -}; - -struct aspeed_smc_controller { - struct device *dev; - - struct mutex mutex; /* controller access mutex */ - const struct aspeed_smc_info *info; /* type info of controller */ - void __iomem *regs; /* controller registers */ - void __iomem *ahb_base; /* per-chip windows resource */ - u32 ahb_window_size; /* full mapping window size */ - - struct aspeed_smc_chip *chips[]; /* pointers to attached chips */ -}; - -/* - * SPI Flash Configuration Register (AST2500 SPI) - * or - * Type setting Register (AST2500 FMC). - * CE0 and CE1 can only be of type SPI. CE2 can be of type NOR but the - * driver does not support it. - */ -#define CONFIG_REG 0x0 -#define CONFIG_DISABLE_LEGACY BIT(31) /* 1 */ - -#define CONFIG_CE2_WRITE BIT(18) -#define CONFIG_CE1_WRITE BIT(17) -#define CONFIG_CE0_WRITE BIT(16) - -#define CONFIG_CE2_TYPE BIT(4) /* AST2500 FMC only */ -#define CONFIG_CE1_TYPE BIT(2) /* AST2500 FMC only */ -#define CONFIG_CE0_TYPE BIT(0) /* AST2500 FMC only */ - -/* - * CE Control Register - */ -#define CE_CONTROL_REG 0x4 - -/* - * CEx Control Register - */ -#define CONTROL_AAF_MODE BIT(31) -#define CONTROL_IO_MODE_MASK GENMASK(30, 28) -#define CONTROL_IO_DUAL_DATA BIT(29) -#define CONTROL_IO_DUAL_ADDR_DATA (BIT(29) | BIT(28)) -#define CONTROL_IO_QUAD_DATA BIT(30) -#define CONTROL_IO_QUAD_ADDR_DATA (BIT(30) | BIT(28)) -#define CONTROL_CE_INACTIVE_SHIFT 24 -#define CONTROL_CE_INACTIVE_MASK GENMASK(27, \ - CONTROL_CE_INACTIVE_SHIFT) -/* 0 = 16T ... 15 = 1T T=HCLK */ -#define CONTROL_COMMAND_SHIFT 16 -#define CONTROL_DUMMY_COMMAND_OUT BIT(15) -#define CONTROL_IO_DUMMY_HI BIT(14) -#define CONTROL_IO_DUMMY_HI_SHIFT 14 -#define CONTROL_CLK_DIV4 BIT(13) /* others */ -#define CONTROL_IO_ADDRESS_4B BIT(13) /* AST2400 SPI */ -#define CONTROL_RW_MERGE BIT(12) -#define CONTROL_IO_DUMMY_LO_SHIFT 6 -#define CONTROL_IO_DUMMY_LO GENMASK(7, \ - CONTROL_IO_DUMMY_LO_SHIFT) -#define CONTROL_IO_DUMMY_MASK (CONTROL_IO_DUMMY_HI | \ - CONTROL_IO_DUMMY_LO) -#define CONTROL_IO_DUMMY_SET(dummy) \ - (((((dummy) >> 2) & 0x1) << CONTROL_IO_DUMMY_HI_SHIFT) | \ - (((dummy) & 0x3) << CONTROL_IO_DUMMY_LO_SHIFT)) - -#define CONTROL_CLOCK_FREQ_SEL_SHIFT 8 -#define CONTROL_CLOCK_FREQ_SEL_MASK GENMASK(11, \ - CONTROL_CLOCK_FREQ_SEL_SHIFT) -#define CONTROL_LSB_FIRST BIT(5) -#define CONTROL_CLOCK_MODE_3 BIT(4) -#define CONTROL_IN_DUAL_DATA BIT(3) -#define CONTROL_CE_STOP_ACTIVE_CONTROL BIT(2) -#define CONTROL_COMMAND_MODE_MASK GENMASK(1, 0) -#define CONTROL_COMMAND_MODE_NORMAL 0 -#define CONTROL_COMMAND_MODE_FREAD 1 -#define CONTROL_COMMAND_MODE_WRITE 2 -#define CONTROL_COMMAND_MODE_USER 3 - -#define CONTROL_KEEP_MASK \ - (CONTROL_AAF_MODE | CONTROL_CE_INACTIVE_MASK | CONTROL_CLK_DIV4 | \ - CONTROL_CLOCK_FREQ_SEL_MASK | CONTROL_LSB_FIRST | CONTROL_CLOCK_MODE_3) - -/* - * The Segment Register uses a 8MB unit to encode the start address - * and the end address of the mapping window of a flash SPI slave : - * - * | byte 1 | byte 2 | byte 3 | byte 4 | - * +--------+--------+--------+--------+ - * | end | start | 0 | 0 | - */ -#define SEGMENT_ADDR_REG0 0x30 -#define SEGMENT_ADDR_START(_r) ((((_r) >> 16) & 0xFF) << 23) -#define SEGMENT_ADDR_END(_r) ((((_r) >> 24) & 0xFF) << 23) -#define SEGMENT_ADDR_VALUE(start, end) \ - (((((start) >> 23) & 0xFF) << 16) | ((((end) >> 23) & 0xFF) << 24)) -#define SEGMENT_ADDR_REG(controller, cs) \ - ((controller)->regs + SEGMENT_ADDR_REG0 + (cs) * 4) - -/* - * In user mode all data bytes read or written to the chip decode address - * range are transferred to or from the SPI bus. The range is treated as a - * fifo of arbitratry 1, 2, or 4 byte width but each write has to be aligned - * to its size. The address within the multiple 8kB range is ignored when - * sending bytes to the SPI bus. - * - * On the arm architecture, as of Linux version 4.3, memcpy_fromio and - * memcpy_toio on little endian targets use the optimized memcpy routines - * that were designed for well behavied memory storage. These routines - * have a stutter if the source and destination are not both word aligned, - * once with a duplicate access to the source after aligning to the - * destination to a word boundary, and again with a duplicate access to - * the source when the final byte count is not word aligned. - * - * When writing or reading the fifo this stutter discards data or sends - * too much data to the fifo and can not be used by this driver. - * - * While the low level io string routines that implement the insl family do - * the desired accesses and memory increments, the cross architecture io - * macros make them essentially impossible to use on a memory mapped address - * instead of a a token from the call to iomap of an io port. - * - * These fifo routines use readl and friends to a constant io port and update - * the memory buffer pointer and count via explicit code. The final updates - * to len are optimistically suppressed. - */ -static int aspeed_smc_read_from_ahb(void *buf, void __iomem *src, size_t len) -{ - size_t offset = 0; - - if (IS_ALIGNED((uintptr_t)src, sizeof(uintptr_t)) && - IS_ALIGNED((uintptr_t)buf, sizeof(uintptr_t))) { - ioread32_rep(src, buf, len >> 2); - offset = len & ~0x3; - len -= offset; - } - ioread8_rep(src, (u8 *)buf + offset, len); - return 0; -} - -static int aspeed_smc_write_to_ahb(void __iomem *dst, const void *buf, - size_t len) -{ - size_t offset = 0; - - if (IS_ALIGNED((uintptr_t)dst, sizeof(uintptr_t)) && - IS_ALIGNED((uintptr_t)buf, sizeof(uintptr_t))) { - iowrite32_rep(dst, buf, len >> 2); - offset = len & ~0x3; - len -= offset; - } - iowrite8_rep(dst, (const u8 *)buf + offset, len); - return 0; -} - -static inline u32 aspeed_smc_chip_write_bit(struct aspeed_smc_chip *chip) -{ - return BIT(chip->controller->info->we0 + chip->cs); -} - -static void aspeed_smc_chip_check_config(struct aspeed_smc_chip *chip) -{ - struct aspeed_smc_controller *controller = chip->controller; - u32 reg; - - reg = readl(controller->regs + CONFIG_REG); - - if (reg & aspeed_smc_chip_write_bit(chip)) - return; - - dev_dbg(controller->dev, "config write is not set ! @%p: 0x%08x\n", - controller->regs + CONFIG_REG, reg); - reg |= aspeed_smc_chip_write_bit(chip); - writel(reg, controller->regs + CONFIG_REG); -} - -static void aspeed_smc_start_user(struct spi_nor *nor) -{ - struct aspeed_smc_chip *chip = nor->priv; - u32 ctl = chip->ctl_val[smc_base]; - - /* - * When the chip is controlled in user mode, we need write - * access to send the opcodes to it. So check the config. - */ - aspeed_smc_chip_check_config(chip); - - ctl |= CONTROL_COMMAND_MODE_USER | - CONTROL_CE_STOP_ACTIVE_CONTROL; - writel(ctl, chip->ctl); - - ctl &= ~CONTROL_CE_STOP_ACTIVE_CONTROL; - writel(ctl, chip->ctl); -} - -static void aspeed_smc_stop_user(struct spi_nor *nor) -{ - struct aspeed_smc_chip *chip = nor->priv; - - u32 ctl = chip->ctl_val[smc_read]; - u32 ctl2 = ctl | CONTROL_COMMAND_MODE_USER | - CONTROL_CE_STOP_ACTIVE_CONTROL; - - writel(ctl2, chip->ctl); /* stop user CE control */ - writel(ctl, chip->ctl); /* default to fread or read mode */ -} - -static int aspeed_smc_prep(struct spi_nor *nor) -{ - struct aspeed_smc_chip *chip = nor->priv; - - mutex_lock(&chip->controller->mutex); - return 0; -} - -static void aspeed_smc_unprep(struct spi_nor *nor) -{ - struct aspeed_smc_chip *chip = nor->priv; - - mutex_unlock(&chip->controller->mutex); -} - -static int aspeed_smc_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, - size_t len) -{ - struct aspeed_smc_chip *chip = nor->priv; - - aspeed_smc_start_user(nor); - aspeed_smc_write_to_ahb(chip->ahb_base, &opcode, 1); - aspeed_smc_read_from_ahb(buf, chip->ahb_base, len); - aspeed_smc_stop_user(nor); - return 0; -} - -static int aspeed_smc_write_reg(struct spi_nor *nor, u8 opcode, const u8 *buf, - size_t len) -{ - struct aspeed_smc_chip *chip = nor->priv; - - aspeed_smc_start_user(nor); - aspeed_smc_write_to_ahb(chip->ahb_base, &opcode, 1); - aspeed_smc_write_to_ahb(chip->ahb_base, buf, len); - aspeed_smc_stop_user(nor); - return 0; -} - -static void aspeed_smc_send_cmd_addr(struct spi_nor *nor, u8 cmd, u32 addr) -{ - struct aspeed_smc_chip *chip = nor->priv; - __be32 temp; - u32 cmdaddr; - - switch (nor->addr_width) { - default: - WARN_ONCE(1, "Unexpected address width %u, defaulting to 3\n", - nor->addr_width); - fallthrough; - case 3: - cmdaddr = addr & 0xFFFFFF; - cmdaddr |= cmd << 24; - - temp = cpu_to_be32(cmdaddr); - aspeed_smc_write_to_ahb(chip->ahb_base, &temp, 4); - break; - case 4: - temp = cpu_to_be32(addr); - aspeed_smc_write_to_ahb(chip->ahb_base, &cmd, 1); - aspeed_smc_write_to_ahb(chip->ahb_base, &temp, 4); - break; - } -} - -static ssize_t aspeed_smc_read_user(struct spi_nor *nor, loff_t from, - size_t len, u_char *read_buf) -{ - struct aspeed_smc_chip *chip = nor->priv; - int i; - u8 dummy = 0xFF; - - aspeed_smc_start_user(nor); - aspeed_smc_send_cmd_addr(nor, nor->read_opcode, from); - for (i = 0; i < chip->nor.read_dummy / 8; i++) - aspeed_smc_write_to_ahb(chip->ahb_base, &dummy, sizeof(dummy)); - - aspeed_smc_read_from_ahb(read_buf, chip->ahb_base, len); - aspeed_smc_stop_user(nor); - return len; -} - -static ssize_t aspeed_smc_write_user(struct spi_nor *nor, loff_t to, - size_t len, const u_char *write_buf) -{ - struct aspeed_smc_chip *chip = nor->priv; - - aspeed_smc_start_user(nor); - aspeed_smc_send_cmd_addr(nor, nor->program_opcode, to); - aspeed_smc_write_to_ahb(chip->ahb_base, write_buf, len); - aspeed_smc_stop_user(nor); - return len; -} - -static int aspeed_smc_unregister(struct aspeed_smc_controller *controller) -{ - struct aspeed_smc_chip *chip; - int n; - - for (n = 0; n < controller->info->nce; n++) { - chip = controller->chips[n]; - if (chip) - mtd_device_unregister(&chip->nor.mtd); - } - - return 0; -} - -static int aspeed_smc_remove(struct platform_device *dev) -{ - return aspeed_smc_unregister(platform_get_drvdata(dev)); -} - -static const struct of_device_id aspeed_smc_matches[] = { - { .compatible = "aspeed,ast2400-fmc", .data = &fmc_2400_info }, - { .compatible = "aspeed,ast2400-spi", .data = &spi_2400_info }, - { .compatible = "aspeed,ast2500-fmc", .data = &fmc_2500_info }, - { .compatible = "aspeed,ast2500-spi", .data = &spi_2500_info }, - { } -}; -MODULE_DEVICE_TABLE(of, aspeed_smc_matches); - -/* - * Each chip has a mapping window defined by a segment address - * register defining a start and an end address on the AHB bus. These - * addresses can be configured to fit the chip size and offer a - * contiguous memory region across chips. For the moment, we only - * check that each chip segment is valid. - */ -static void __iomem *aspeed_smc_chip_base(struct aspeed_smc_chip *chip, - struct resource *res) -{ - struct aspeed_smc_controller *controller = chip->controller; - u32 offset = 0; - u32 reg; - - if (controller->info->nce > 1) { - reg = readl(SEGMENT_ADDR_REG(controller, chip->cs)); - - if (SEGMENT_ADDR_START(reg) >= SEGMENT_ADDR_END(reg)) - return NULL; - - offset = SEGMENT_ADDR_START(reg) - res->start; - } - - return controller->ahb_base + offset; -} - -static u32 aspeed_smc_ahb_base_phy(struct aspeed_smc_controller *controller) -{ - u32 seg0_val = readl(SEGMENT_ADDR_REG(controller, 0)); - - return SEGMENT_ADDR_START(seg0_val); -} - -static u32 chip_set_segment(struct aspeed_smc_chip *chip, u32 cs, u32 start, - u32 size) -{ - struct aspeed_smc_controller *controller = chip->controller; - void __iomem *seg_reg; - u32 seg_oldval, seg_newval, ahb_base_phy, end; - - ahb_base_phy = aspeed_smc_ahb_base_phy(controller); - - seg_reg = SEGMENT_ADDR_REG(controller, cs); - seg_oldval = readl(seg_reg); - - /* - * If the chip size is not specified, use the default segment - * size, but take into account the possible overlap with the - * previous segment - */ - if (!size) - size = SEGMENT_ADDR_END(seg_oldval) - start; - - /* - * The segment cannot exceed the maximum window size of the - * controller. - */ - if (start + size > ahb_base_phy + controller->ahb_window_size) { - size = ahb_base_phy + controller->ahb_window_size - start; - dev_warn(chip->nor.dev, "CE%d window resized to %dMB", - cs, size >> 20); - } - - end = start + size; - seg_newval = SEGMENT_ADDR_VALUE(start, end); - writel(seg_newval, seg_reg); - - /* - * Restore default value if something goes wrong. The chip - * might have set some bogus value and we would loose access - * to the chip. - */ - if (seg_newval != readl(seg_reg)) { - dev_err(chip->nor.dev, "CE%d window invalid", cs); - writel(seg_oldval, seg_reg); - start = SEGMENT_ADDR_START(seg_oldval); - end = SEGMENT_ADDR_END(seg_oldval); - size = end - start; - } - - dev_info(chip->nor.dev, "CE%d window [ 0x%.8x - 0x%.8x ] %dMB", - cs, start, end, size >> 20); - - return size; -} - -/* - * The segment register defines the mapping window on the AHB bus and - * it needs to be configured depending on the chip size. The segment - * register of the following CE also needs to be tuned in order to - * provide a contiguous window across multiple chips. - * - * This is expected to be called in increasing CE order - */ -static u32 aspeed_smc_chip_set_segment(struct aspeed_smc_chip *chip) -{ - struct aspeed_smc_controller *controller = chip->controller; - u32 ahb_base_phy, start; - u32 size = chip->nor.mtd.size; - - /* - * Each controller has a chip size limit for direct memory - * access - */ - if (size > controller->info->maxsize) - size = controller->info->maxsize; - - /* - * The AST2400 SPI controller only handles one chip and does - * not have segment registers. Let's use the chip size for the - * AHB window. - */ - if (controller->info == &spi_2400_info) - goto out; - - /* - * The AST2500 SPI controller has a HW bug when the CE0 chip - * size reaches 128MB. Enforce a size limit of 120MB to - * prevent the controller from using bogus settings in the - * segment register. - */ - if (chip->cs == 0 && controller->info == &spi_2500_info && - size == SZ_128M) { - size = 120 << 20; - dev_info(chip->nor.dev, - "CE%d window resized to %dMB (AST2500 HW quirk)", - chip->cs, size >> 20); - } - - ahb_base_phy = aspeed_smc_ahb_base_phy(controller); - - /* - * As a start address for the current segment, use the default - * start address if we are handling CE0 or use the previous - * segment ending address - */ - if (chip->cs) { - u32 prev = readl(SEGMENT_ADDR_REG(controller, chip->cs - 1)); - - start = SEGMENT_ADDR_END(prev); - } else { - start = ahb_base_phy; - } - - size = chip_set_segment(chip, chip->cs, start, size); - - /* Update chip base address on the AHB bus */ - chip->ahb_base = controller->ahb_base + (start - ahb_base_phy); - - /* - * Now, make sure the next segment does not overlap with the - * current one we just configured, even if there is no - * available chip. That could break access in Command Mode. - */ - if (chip->cs < controller->info->nce - 1) - chip_set_segment(chip, chip->cs + 1, start + size, 0); - -out: - if (size < chip->nor.mtd.size) - dev_warn(chip->nor.dev, - "CE%d window too small for chip %dMB", - chip->cs, (u32)chip->nor.mtd.size >> 20); - - return size; -} - -static void aspeed_smc_chip_enable_write(struct aspeed_smc_chip *chip) -{ - struct aspeed_smc_controller *controller = chip->controller; - u32 reg; - - reg = readl(controller->regs + CONFIG_REG); - - reg |= aspeed_smc_chip_write_bit(chip); - writel(reg, controller->regs + CONFIG_REG); -} - -static void aspeed_smc_chip_set_type(struct aspeed_smc_chip *chip, int type) -{ - struct aspeed_smc_controller *controller = chip->controller; - u32 reg; - - chip->type = type; - - reg = readl(controller->regs + CONFIG_REG); - reg &= ~(3 << (chip->cs * 2)); - reg |= chip->type << (chip->cs * 2); - writel(reg, controller->regs + CONFIG_REG); -} - -/* - * The first chip of the AST2500 FMC flash controller is strapped by - * hardware, or autodetected, but other chips need to be set. Enforce - * the 4B setting for all chips. - */ -static void aspeed_smc_chip_set_4b(struct aspeed_smc_chip *chip) -{ - struct aspeed_smc_controller *controller = chip->controller; - u32 reg; - - reg = readl(controller->regs + CE_CONTROL_REG); - reg |= 1 << chip->cs; - writel(reg, controller->regs + CE_CONTROL_REG); -} - -/* - * The AST2400 SPI flash controller does not have a CE Control - * register. It uses the CE0 control register to set 4Byte mode at the - * controller level. - */ -static void aspeed_smc_chip_set_4b_spi_2400(struct aspeed_smc_chip *chip) -{ - chip->ctl_val[smc_base] |= CONTROL_IO_ADDRESS_4B; - chip->ctl_val[smc_read] |= CONTROL_IO_ADDRESS_4B; -} - -static int aspeed_smc_chip_setup_init(struct aspeed_smc_chip *chip, - struct resource *res) -{ - struct aspeed_smc_controller *controller = chip->controller; - const struct aspeed_smc_info *info = controller->info; - u32 reg, base_reg; - - /* - * Always turn on the write enable bit to allow opcodes to be - * sent in user mode. - */ - aspeed_smc_chip_enable_write(chip); - - /* The driver only supports SPI type flash */ - if (info->hastype) - aspeed_smc_chip_set_type(chip, smc_type_spi); - - /* - * Configure chip base address in memory - */ - chip->ahb_base = aspeed_smc_chip_base(chip, res); - if (!chip->ahb_base) { - dev_warn(chip->nor.dev, "CE%d window closed", chip->cs); - return -EINVAL; - } - - /* - * Get value of the inherited control register. U-Boot usually - * does some timing calibration on the FMC chip, so it's good - * to keep them. In the future, we should handle calibration - * from Linux. - */ - reg = readl(chip->ctl); - dev_dbg(controller->dev, "control register: %08x\n", reg); - - base_reg = reg & CONTROL_KEEP_MASK; - if (base_reg != reg) { - dev_dbg(controller->dev, - "control register changed to: %08x\n", - base_reg); - } - chip->ctl_val[smc_base] = base_reg; - - /* - * Retain the prior value of the control register as the - * default if it was normal access mode. Otherwise start with - * the sanitized base value set to read mode. - */ - if ((reg & CONTROL_COMMAND_MODE_MASK) == - CONTROL_COMMAND_MODE_NORMAL) - chip->ctl_val[smc_read] = reg; - else - chip->ctl_val[smc_read] = chip->ctl_val[smc_base] | - CONTROL_COMMAND_MODE_NORMAL; - - dev_dbg(controller->dev, "default control register: %08x\n", - chip->ctl_val[smc_read]); - return 0; -} - -static int aspeed_smc_chip_setup_finish(struct aspeed_smc_chip *chip) -{ - struct aspeed_smc_controller *controller = chip->controller; - const struct aspeed_smc_info *info = controller->info; - u32 cmd; - - if (chip->nor.addr_width == 4 && info->set_4b) - info->set_4b(chip); - - /* This is for direct AHB access when using Command Mode. */ - chip->ahb_window_size = aspeed_smc_chip_set_segment(chip); - - /* - * base mode has not been optimized yet. use it for writes. - */ - chip->ctl_val[smc_write] = chip->ctl_val[smc_base] | - chip->nor.program_opcode << CONTROL_COMMAND_SHIFT | - CONTROL_COMMAND_MODE_WRITE; - - dev_dbg(controller->dev, "write control register: %08x\n", - chip->ctl_val[smc_write]); - - /* - * TODO: Adjust clocks if fast read is supported and interpret - * SPI NOR flags to adjust controller settings. - */ - if (chip->nor.read_proto == SNOR_PROTO_1_1_1) { - if (chip->nor.read_dummy == 0) - cmd = CONTROL_COMMAND_MODE_NORMAL; - else - cmd = CONTROL_COMMAND_MODE_FREAD; - } else { - dev_err(chip->nor.dev, "unsupported SPI read mode\n"); - return -EINVAL; - } - - chip->ctl_val[smc_read] |= cmd | - CONTROL_IO_DUMMY_SET(chip->nor.read_dummy / 8); - - dev_dbg(controller->dev, "base control register: %08x\n", - chip->ctl_val[smc_read]); - return 0; -} - -static const struct spi_nor_controller_ops aspeed_smc_controller_ops = { - .prepare = aspeed_smc_prep, - .unprepare = aspeed_smc_unprep, - .read_reg = aspeed_smc_read_reg, - .write_reg = aspeed_smc_write_reg, - .read = aspeed_smc_read_user, - .write = aspeed_smc_write_user, -}; - -static int aspeed_smc_setup_flash(struct aspeed_smc_controller *controller, - struct device_node *np, struct resource *r) -{ - const struct spi_nor_hwcaps hwcaps = { - .mask = SNOR_HWCAPS_READ | - SNOR_HWCAPS_READ_FAST | - SNOR_HWCAPS_PP, - }; - const struct aspeed_smc_info *info = controller->info; - struct device *dev = controller->dev; - struct device_node *child; - unsigned int cs; - int ret = -ENODEV; - bool found_one = false; - - for_each_available_child_of_node(np, child) { - struct aspeed_smc_chip *chip; - struct spi_nor *nor; - struct mtd_info *mtd; - - /* This driver does not support NAND or NOR flash devices. */ - if (!of_device_is_compatible(child, "jedec,spi-nor")) - continue; - - ret = of_property_read_u32(child, "reg", &cs); - if (ret) { - dev_err(dev, "Couldn't not read chip select.\n"); - break; - } - - if (cs >= info->nce) { - dev_err(dev, "Chip select %d out of range.\n", - cs); - ret = -ERANGE; - break; - } - - if (controller->chips[cs]) { - dev_err(dev, "Chip select %d already in use by %s\n", - cs, dev_name(controller->chips[cs]->nor.dev)); - ret = -EBUSY; - break; - } - - chip = devm_kzalloc(controller->dev, sizeof(*chip), GFP_KERNEL); - if (!chip) { - ret = -ENOMEM; - break; - } - - chip->controller = controller; - chip->ctl = controller->regs + info->ctl0 + cs * 4; - chip->cs = cs; - - nor = &chip->nor; - mtd = &nor->mtd; - - nor->dev = dev; - nor->priv = chip; - spi_nor_set_flash_node(nor, child); - nor->controller_ops = &aspeed_smc_controller_ops; - - ret = aspeed_smc_chip_setup_init(chip, r); - if (ret) - break; - - /* - * TODO: Add support for Dual and Quad SPI protocols - * attach when board support is present as determined - * by of property. - */ - ret = spi_nor_scan(nor, NULL, &hwcaps); - /* - * If we fail to scan the device it might not be present or - * broken. Don't fail the whole controller if others work. - */ - if (ret) { - if (found_one) - ret = 0; - - devm_kfree(controller->dev, chip); - continue; - } - - ret = aspeed_smc_chip_setup_finish(chip); - if (ret) - break; - - ret = mtd_device_register(mtd, NULL, 0); - if (ret) - break; - - controller->chips[cs] = chip; - found_one = true; - } - - if (ret) { - of_node_put(child); - aspeed_smc_unregister(controller); - } - - return ret; -} - -static int aspeed_smc_probe(struct platform_device *pdev) -{ - struct device_node *np = pdev->dev.of_node; - struct device *dev = &pdev->dev; - struct aspeed_smc_controller *controller; - const struct of_device_id *match; - const struct aspeed_smc_info *info; - struct resource *res; - int ret; - - match = of_match_device(aspeed_smc_matches, &pdev->dev); - if (!match || !match->data) - return -ENODEV; - info = match->data; - - controller = devm_kzalloc(&pdev->dev, - struct_size(controller, chips, info->nce), - GFP_KERNEL); - if (!controller) - return -ENOMEM; - controller->info = info; - controller->dev = dev; - - mutex_init(&controller->mutex); - platform_set_drvdata(pdev, controller); - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - controller->regs = devm_ioremap_resource(dev, res); - if (IS_ERR(controller->regs)) - return PTR_ERR(controller->regs); - - res = platform_get_resource(pdev, IORESOURCE_MEM, 1); - controller->ahb_base = devm_ioremap_resource(dev, res); - if (IS_ERR(controller->ahb_base)) - return PTR_ERR(controller->ahb_base); - - controller->ahb_window_size = resource_size(res); - - ret = aspeed_smc_setup_flash(controller, np, res); - if (ret) - dev_err(dev, "Aspeed SMC probe failed %d\n", ret); - - return ret; -} - -static struct platform_driver aspeed_smc_driver = { - .probe = aspeed_smc_probe, - .remove = aspeed_smc_remove, - .driver = { - .name = DEVICE_NAME, - .of_match_table = aspeed_smc_matches, - } -}; - -module_platform_driver(aspeed_smc_driver); - -MODULE_DESCRIPTION("ASPEED Static Memory Controller Driver"); -MODULE_AUTHOR("Cedric Le Goater <clg@kaod.org>"); -MODULE_LICENSE("GPL v2"); |