summaryrefslogtreecommitdiffstats
path: root/drivers/infiniband/hw/qib/qib_eeprom.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/infiniband/hw/qib/qib_eeprom.c')
-rw-r--r--drivers/infiniband/hw/qib/qib_eeprom.c198
1 files changed, 9 insertions, 189 deletions
diff --git a/drivers/infiniband/hw/qib/qib_eeprom.c b/drivers/infiniband/hw/qib/qib_eeprom.c
index 4d5d71aaa2b4..311ee6c3dd5e 100644
--- a/drivers/infiniband/hw/qib/qib_eeprom.c
+++ b/drivers/infiniband/hw/qib/qib_eeprom.c
@@ -153,6 +153,7 @@ void qib_get_eeprom_info(struct qib_devdata *dd)
if (t && dd0->nguid > 1 && t <= dd0->nguid) {
u8 oguid;
+
dd->base_guid = dd0->base_guid;
bguid = (u8 *) &dd->base_guid;
@@ -251,206 +252,25 @@ void qib_get_eeprom_info(struct qib_devdata *dd)
* This board has a Serial-prefix, which is stored
* elsewhere for backward-compatibility.
*/
- memcpy(snp, ifp->if_sprefix, sizeof ifp->if_sprefix);
- snp[sizeof ifp->if_sprefix] = '\0';
+ memcpy(snp, ifp->if_sprefix, sizeof(ifp->if_sprefix));
+ snp[sizeof(ifp->if_sprefix)] = '\0';
len = strlen(snp);
snp += len;
- len = (sizeof dd->serial) - len;
- if (len > sizeof ifp->if_serial)
- len = sizeof ifp->if_serial;
+ len = sizeof(dd->serial) - len;
+ if (len > sizeof(ifp->if_serial))
+ len = sizeof(ifp->if_serial);
memcpy(snp, ifp->if_serial, len);
- } else
- memcpy(dd->serial, ifp->if_serial,
- sizeof ifp->if_serial);
+ } else {
+ memcpy(dd->serial, ifp->if_serial, sizeof(ifp->if_serial));
+ }
if (!strstr(ifp->if_comment, "Tested successfully"))
qib_dev_err(dd,
"Board SN %s did not pass functional test: %s\n",
dd->serial, ifp->if_comment);
- memcpy(&dd->eep_st_errs, &ifp->if_errcntp, QIB_EEP_LOG_CNT);
- /*
- * Power-on (actually "active") hours are kept as little-endian value
- * in EEPROM, but as seconds in a (possibly as small as 24-bit)
- * atomic_t while running.
- */
- atomic_set(&dd->active_time, 0);
- dd->eep_hrs = ifp->if_powerhour[0] | (ifp->if_powerhour[1] << 8);
-
done:
vfree(buf);
bail:;
}
-/**
- * qib_update_eeprom_log - copy active-time and error counters to eeprom
- * @dd: the qlogic_ib device
- *
- * Although the time is kept as seconds in the qib_devdata struct, it is
- * rounded to hours for re-write, as we have only 16 bits in EEPROM.
- * First-cut code reads whole (expected) struct qib_flash, modifies,
- * re-writes. Future direction: read/write only what we need, assuming
- * that the EEPROM had to have been "good enough" for driver init, and
- * if not, we aren't making it worse.
- *
- */
-int qib_update_eeprom_log(struct qib_devdata *dd)
-{
- void *buf;
- struct qib_flash *ifp;
- int len, hi_water;
- uint32_t new_time, new_hrs;
- u8 csum;
- int ret, idx;
- unsigned long flags;
-
- /* first, check if we actually need to do anything. */
- ret = 0;
- for (idx = 0; idx < QIB_EEP_LOG_CNT; ++idx) {
- if (dd->eep_st_new_errs[idx]) {
- ret = 1;
- break;
- }
- }
- new_time = atomic_read(&dd->active_time);
-
- if (ret == 0 && new_time < 3600)
- goto bail;
-
- /*
- * The quick-check above determined that there is something worthy
- * of logging, so get current contents and do a more detailed idea.
- * read full flash, not just currently used part, since it may have
- * been written with a newer definition
- */
- len = sizeof(struct qib_flash);
- buf = vmalloc(len);
- ret = 1;
- if (!buf) {
- qib_dev_err(dd,
- "Couldn't allocate memory to read %u bytes from eeprom for logging\n",
- len);
- goto bail;
- }
-
- /* Grab semaphore and read current EEPROM. If we get an
- * error, let go, but if not, keep it until we finish write.
- */
- ret = mutex_lock_interruptible(&dd->eep_lock);
- if (ret) {
- qib_dev_err(dd, "Unable to acquire EEPROM for logging\n");
- goto free_bail;
- }
- ret = qib_twsi_blk_rd(dd, dd->twsi_eeprom_dev, 0, buf, len);
- if (ret) {
- mutex_unlock(&dd->eep_lock);
- qib_dev_err(dd, "Unable read EEPROM for logging\n");
- goto free_bail;
- }
- ifp = (struct qib_flash *)buf;
-
- csum = flash_csum(ifp, 0);
- if (csum != ifp->if_csum) {
- mutex_unlock(&dd->eep_lock);
- qib_dev_err(dd, "EEPROM cks err (0x%02X, S/B 0x%02X)\n",
- csum, ifp->if_csum);
- ret = 1;
- goto free_bail;
- }
- hi_water = 0;
- spin_lock_irqsave(&dd->eep_st_lock, flags);
- for (idx = 0; idx < QIB_EEP_LOG_CNT; ++idx) {
- int new_val = dd->eep_st_new_errs[idx];
- if (new_val) {
- /*
- * If we have seen any errors, add to EEPROM values
- * We need to saturate at 0xFF (255) and we also
- * would need to adjust the checksum if we were
- * trying to minimize EEPROM traffic
- * Note that we add to actual current count in EEPROM,
- * in case it was altered while we were running.
- */
- new_val += ifp->if_errcntp[idx];
- if (new_val > 0xFF)
- new_val = 0xFF;
- if (ifp->if_errcntp[idx] != new_val) {
- ifp->if_errcntp[idx] = new_val;
- hi_water = offsetof(struct qib_flash,
- if_errcntp) + idx;
- }
- /*
- * update our shadow (used to minimize EEPROM
- * traffic), to match what we are about to write.
- */
- dd->eep_st_errs[idx] = new_val;
- dd->eep_st_new_errs[idx] = 0;
- }
- }
- /*
- * Now update active-time. We would like to round to the nearest hour
- * but unless atomic_t are sure to be proper signed ints we cannot,
- * because we need to account for what we "transfer" to EEPROM and
- * if we log an hour at 31 minutes, then we would need to set
- * active_time to -29 to accurately count the _next_ hour.
- */
- if (new_time >= 3600) {
- new_hrs = new_time / 3600;
- atomic_sub((new_hrs * 3600), &dd->active_time);
- new_hrs += dd->eep_hrs;
- if (new_hrs > 0xFFFF)
- new_hrs = 0xFFFF;
- dd->eep_hrs = new_hrs;
- if ((new_hrs & 0xFF) != ifp->if_powerhour[0]) {
- ifp->if_powerhour[0] = new_hrs & 0xFF;
- hi_water = offsetof(struct qib_flash, if_powerhour);
- }
- if ((new_hrs >> 8) != ifp->if_powerhour[1]) {
- ifp->if_powerhour[1] = new_hrs >> 8;
- hi_water = offsetof(struct qib_flash, if_powerhour) + 1;
- }
- }
- /*
- * There is a tiny possibility that we could somehow fail to write
- * the EEPROM after updating our shadows, but problems from holding
- * the spinlock too long are a much bigger issue.
- */
- spin_unlock_irqrestore(&dd->eep_st_lock, flags);
- if (hi_water) {
- /* we made some change to the data, uopdate cksum and write */
- csum = flash_csum(ifp, 1);
- ret = eeprom_write_with_enable(dd, 0, buf, hi_water + 1);
- }
- mutex_unlock(&dd->eep_lock);
- if (ret)
- qib_dev_err(dd, "Failed updating EEPROM\n");
-
-free_bail:
- vfree(buf);
-bail:
- return ret;
-}
-
-/**
- * qib_inc_eeprom_err - increment one of the four error counters
- * that are logged to EEPROM.
- * @dd: the qlogic_ib device
- * @eidx: 0..3, the counter to increment
- * @incr: how much to add
- *
- * Each counter is 8-bits, and saturates at 255 (0xFF). They
- * are copied to the EEPROM (aka flash) whenever qib_update_eeprom_log()
- * is called, but it can only be called in a context that allows sleep.
- * This function can be called even at interrupt level.
- */
-void qib_inc_eeprom_err(struct qib_devdata *dd, u32 eidx, u32 incr)
-{
- uint new_val;
- unsigned long flags;
-
- spin_lock_irqsave(&dd->eep_st_lock, flags);
- new_val = dd->eep_st_new_errs[eidx] + incr;
- if (new_val > 255)
- new_val = 255;
- dd->eep_st_new_errs[eidx] = new_val;
- spin_unlock_irqrestore(&dd->eep_st_lock, flags);
-}