1 files changed, 293 insertions, 41 deletions

diff --git a/drivers/hwmon/ina2xx.c b/drivers/hwmon/ina2xx.c
index e01feba909c3..d1542b7d4bc3 100644
--- a/drivers/hwmon/ina2xx.c
+++ b/drivers/hwmon/ina2xx.c
@@ -35,6 +35,7 @@
 #include <linux/hwmon-sysfs.h>
 #include <linux/jiffies.h>
 #include <linux/of.h>
+#include <linux/delay.h>
 
 #include <linux/platform_data/ina2xx.h>
 
@@ -51,7 +52,6 @@
 #define INA226_ALERT_LIMIT		0x07
 #define INA226_DIE_ID			0xFF
 
-
 /* register count */
 #define INA219_REGISTERS		6
 #define INA226_REGISTERS		8
@@ -64,6 +64,24 @@
 
 /* worst case is 68.10 ms (~14.6Hz, ina219) */
 #define INA2XX_CONVERSION_RATE		15
+#define INA2XX_MAX_DELAY		69 /* worst case delay in ms */
+
+#define INA2XX_RSHUNT_DEFAULT		10000
+
+/* bit mask for reading the averaging setting in the configuration register */
+#define INA226_AVG_RD_MASK		0x0E00
+
+#define INA226_READ_AVG(reg)		(((reg) & INA226_AVG_RD_MASK) >> 9)
+#define INA226_SHIFT_AVG(val)		((val) << 9)
+
+/* common attrs, ina226 attrs and NULL */
+#define INA2XX_MAX_ATTRIBUTE_GROUPS	3
+
+/*
+ * Both bus voltage and shunt voltage conversion times for ina226 are set
+ * to 0b0100 on POR, which translates to 2200 microseconds in total.
+ */
+#define INA226_TOTAL_CONV_TIME_DEFAULT	2200
 
 enum ina2xx_ids { ina219, ina226 };
 
@@ -81,11 +99,16 @@ struct ina2xx_data {
 	struct i2c_client *client;
 	const struct ina2xx_config *config;
 
+	long rshunt;
+	u16 curr_config;
+
 	struct mutex update_lock;
 	bool valid;
 	unsigned long last_updated;
+	int update_interval; /* in jiffies */
 
 	int kind;
+	const struct attribute_group *groups[INA2XX_MAX_ATTRIBUTE_GROUPS];
 	u16 regs[INA2XX_MAX_REGISTERS];
 };
 
@@ -110,34 +133,156 @@ static const struct ina2xx_config ina2xx_config[] = {
 	},
 };
 
-static struct ina2xx_data *ina2xx_update_device(struct device *dev)
+/*
+ * Available averaging rates for ina226. The indices correspond with
+ * the bit values expected by the chip (according to the ina226 datasheet,
+ * table 3 AVG bit settings, found at
+ * http://www.ti.com/lit/ds/symlink/ina226.pdf.
+ */
+static const int ina226_avg_tab[] = { 1, 4, 16, 64, 128, 256, 512, 1024 };
+
+static int ina226_avg_bits(int avg)
+{
+	int i;
+
+	/* Get the closest average from the tab. */
+	for (i = 0; i < ARRAY_SIZE(ina226_avg_tab) - 1; i++) {
+		if (avg <= (ina226_avg_tab[i] + ina226_avg_tab[i + 1]) / 2)
+			break;
+	}
+
+	return i; /* Return 0b0111 for values greater than 1024. */
+}
+
+static int ina226_reg_to_interval(u16 config)
+{
+	int avg = ina226_avg_tab[INA226_READ_AVG(config)];
+
+	/*
+	 * Multiply the total conversion time by the number of averages.
+	 * Return the result in milliseconds.
+	 */
+	return DIV_ROUND_CLOSEST(avg * INA226_TOTAL_CONV_TIME_DEFAULT, 1000);
+}
+
+static u16 ina226_interval_to_reg(int interval, u16 config)
+{
+	int avg, avg_bits;
+
+	avg = DIV_ROUND_CLOSEST(interval * 1000,
+				INA226_TOTAL_CONV_TIME_DEFAULT);
+	avg_bits = ina226_avg_bits(avg);
+
+	return (config & ~INA226_AVG_RD_MASK) | INA226_SHIFT_AVG(avg_bits);
+}
+
+static void ina226_set_update_interval(struct ina2xx_data *data)
+{
+	int ms;
+
+	ms = ina226_reg_to_interval(data->curr_config);
+	data->update_interval = msecs_to_jiffies(ms);
+}
+
+static int ina2xx_calibrate(struct ina2xx_data *data)
+{
+	u16 val = DIV_ROUND_CLOSEST(data->config->calibration_factor,
+				    data->rshunt);
+
+	return i2c_smbus_write_word_swapped(data->client,
+					    INA2XX_CALIBRATION, val);
+}
+
+/*
+ * Initialize the configuration and calibration registers.
+ */
+static int ina2xx_init(struct ina2xx_data *data)
 {
-	struct ina2xx_data *data = dev_get_drvdata(dev);
 	struct i2c_client *client = data->client;
-	struct ina2xx_data *ret = data;
+	int ret;
 
-	mutex_lock(&data->update_lock);
+	/* device configuration */
+	ret = i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
+					   data->curr_config);
+	if (ret < 0)
+		return ret;
 
-	if (time_after(jiffies, data->last_updated +
-		       HZ / INA2XX_CONVERSION_RATE) || !data->valid) {
+	/*
+	 * Set current LSB to 1mA, shunt is in uOhms
+	 * (equation 13 in datasheet).
+	 */
+	return ina2xx_calibrate(data);
+}
 
-		int i;
+static int ina2xx_do_update(struct device *dev)
+{
+	struct ina2xx_data *data = dev_get_drvdata(dev);
+	struct i2c_client *client = data->client;
+	int i, rv, retry;
 
-		dev_dbg(&client->dev, "Starting ina2xx update\n");
+	dev_dbg(&client->dev, "Starting ina2xx update\n");
 
+	for (retry = 5; retry; retry--) {
 		/* Read all registers */
 		for (i = 0; i < data->config->registers; i++) {
-			int rv = i2c_smbus_read_word_swapped(client, i);
-			if (rv < 0) {
-				ret = ERR_PTR(rv);
-				goto abort;
-			}
+			rv = i2c_smbus_read_word_swapped(client, i);
+			if (rv < 0)
+				return rv;
 			data->regs[i] = rv;
 		}
+
+		/*
+		 * If the current value in the calibration register is 0, the
+		 * power and current registers will also remain at 0. In case
+		 * the chip has been reset let's check the calibration
+		 * register and reinitialize if needed.
+		 */
+		if (data->regs[INA2XX_CALIBRATION] == 0) {
+			dev_warn(dev, "chip not calibrated, reinitializing\n");
+
+			rv = ina2xx_init(data);
+			if (rv < 0)
+				return rv;
+
+			/*
+			 * Let's make sure the power and current registers
+			 * have been updated before trying again.
+			 */
+			msleep(INA2XX_MAX_DELAY);
+			continue;
+		}
+
 		data->last_updated = jiffies;
 		data->valid = 1;
+
+		return 0;
 	}
-abort:
+
+	/*
+	 * If we're here then although all write operations succeeded, the
+	 * chip still returns 0 in the calibration register. Nothing more we
+	 * can do here.
+	 */
+	dev_err(dev, "unable to reinitialize the chip\n");
+	return -ENODEV;
+}
+
+static struct ina2xx_data *ina2xx_update_device(struct device *dev)
+{
+	struct ina2xx_data *data = dev_get_drvdata(dev);
+	struct ina2xx_data *ret = data;
+	unsigned long after;
+	int rv;
+
+	mutex_lock(&data->update_lock);
+
+	after = data->last_updated + data->update_interval;
+	if (time_after(jiffies, after) || !data->valid) {
+		rv = ina2xx_do_update(dev);
+		if (rv < 0)
+			ret = ERR_PTR(rv);
+	}
+
 	mutex_unlock(&data->update_lock);
 	return ret;
 }
@@ -164,6 +309,10 @@ static int ina2xx_get_value(struct ina2xx_data *data, u8 reg)
 		/* signed register, LSB=1mA (selected), in mA */
 		val = (s16)data->regs[reg];
 		break;
+	case INA2XX_CALIBRATION:
+		val = DIV_ROUND_CLOSEST(data->config->calibration_factor,
+					data->regs[reg]);
+		break;
 	default:
 		/* programmer goofed */
 		WARN_ON_ONCE(1);
@@ -187,6 +336,85 @@ static ssize_t ina2xx_show_value(struct device *dev,
 			ina2xx_get_value(data, attr->index));
 }
 
+static ssize_t ina2xx_set_shunt(struct device *dev,
+				struct device_attribute *da,
+				const char *buf, size_t count)
+{
+	struct ina2xx_data *data = ina2xx_update_device(dev);
+	unsigned long val;
+	int status;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	status = kstrtoul(buf, 10, &val);
+	if (status < 0)
+		return status;
+
+	if (val == 0 ||
+	    /* Values greater than the calibration factor make no sense. */
+	    val > data->config->calibration_factor)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	data->rshunt = val;
+	status = ina2xx_calibrate(data);
+	mutex_unlock(&data->update_lock);
+	if (status < 0)
+		return status;
+
+	return count;
+}
+
+static ssize_t ina226_set_interval(struct device *dev,
+				   struct device_attribute *da,
+				   const char *buf, size_t count)
+{
+	struct ina2xx_data *data = dev_get_drvdata(dev);
+	unsigned long val;
+	int status;
+
+	status = kstrtoul(buf, 10, &val);
+	if (status < 0)
+		return status;
+
+	if (val > INT_MAX || val == 0)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	data->curr_config = ina226_interval_to_reg(val,
+						   data->regs[INA2XX_CONFIG]);
+	status = i2c_smbus_write_word_swapped(data->client,
+					      INA2XX_CONFIG,
+					      data->curr_config);
+
+	ina226_set_update_interval(data);
+	/* Make sure the next access re-reads all registers. */
+	data->valid = 0;
+	mutex_unlock(&data->update_lock);
+	if (status < 0)
+		return status;
+
+	return count;
+}
+
+static ssize_t ina226_show_interval(struct device *dev,
+				    struct device_attribute *da, char *buf)
+{
+	struct ina2xx_data *data = ina2xx_update_device(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	/*
+	 * We don't use data->update_interval here as we want to display
+	 * the actual interval used by the chip and jiffies_to_msecs()
+	 * doesn't seem to be accurate enough.
+	 */
+	return snprintf(buf, PAGE_SIZE, "%d\n",
+			ina226_reg_to_interval(data->regs[INA2XX_CONFIG]));
+}
+
 /* shunt voltage */
 static SENSOR_DEVICE_ATTR(in0_input, S_IRUGO, ina2xx_show_value, NULL,
 			  INA2XX_SHUNT_VOLTAGE);
@@ -203,15 +431,37 @@ static SENSOR_DEVICE_ATTR(curr1_input, S_IRUGO, ina2xx_show_value, NULL,
 static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, ina2xx_show_value, NULL,
 			  INA2XX_POWER);
 
+/* shunt resistance */
+static SENSOR_DEVICE_ATTR(shunt_resistor, S_IRUGO | S_IWUSR,
+			  ina2xx_show_value, ina2xx_set_shunt,
+			  INA2XX_CALIBRATION);
+
+/* update interval (ina226 only) */
+static SENSOR_DEVICE_ATTR(update_interval, S_IRUGO | S_IWUSR,
+			  ina226_show_interval, ina226_set_interval, 0);
+
 /* pointers to created device attributes */
 static struct attribute *ina2xx_attrs[] = {
 	&sensor_dev_attr_in0_input.dev_attr.attr,
 	&sensor_dev_attr_in1_input.dev_attr.attr,
 	&sensor_dev_attr_curr1_input.dev_attr.attr,
 	&sensor_dev_attr_power1_input.dev_attr.attr,
+	&sensor_dev_attr_shunt_resistor.dev_attr.attr,
 	NULL,
 };
-ATTRIBUTE_GROUPS(ina2xx);
+
+static const struct attribute_group ina2xx_group = {
+	.attrs = ina2xx_attrs,
+};
+
+static struct attribute *ina226_attrs[] = {
+	&sensor_dev_attr_update_interval.dev_attr.attr,
+	NULL,
+};
+
+static const struct attribute_group ina226_group = {
+	.attrs = ina226_attrs,
+};
 
 static int ina2xx_probe(struct i2c_client *client,
 			const struct i2c_device_id *id)
@@ -221,9 +471,8 @@ static int ina2xx_probe(struct i2c_client *client,
 	struct device *dev = &client->dev;
 	struct ina2xx_data *data;
 	struct device *hwmon_dev;
-	long shunt = 10000; /* default shunt value 10mOhms */
 	u32 val;
-	int ret;
+	int ret, group = 0;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_WORD_DATA))
 		return -ENODEV;
@@ -234,50 +483,52 @@ static int ina2xx_probe(struct i2c_client *client,
 
 	if (dev_get_platdata(dev)) {
 		pdata = dev_get_platdata(dev);
-		shunt = pdata->shunt_uohms;
+		data->rshunt = pdata->shunt_uohms;
 	} else if (!of_property_read_u32(dev->of_node,
 					 "shunt-resistor", &val)) {
-		shunt = val;
+		data->rshunt = val;
+	} else {
+		data->rshunt = INA2XX_RSHUNT_DEFAULT;
 	}
 
-	if (shunt <= 0)
-		return -ENODEV;
-
 	/* set the device type */
 	data->kind = id->driver_data;
 	data->config = &ina2xx_config[data->kind];
-
-	/* device configuration */
-	ret = i2c_smbus_write_word_swapped(client, INA2XX_CONFIG,
-					   data->config->config_default);
-	if (ret < 0) {
-		dev_err(dev,
-			"error writing to the config register: %d", ret);
-		return -ENODEV;
-	}
+	data->curr_config = data->config->config_default;
+	data->client = client;
 
 	/*
-	 * Set current LSB to 1mA, shunt is in uOhms
-	 * (equation 13 in datasheet).
+	 * Ina226 has a variable update_interval. For ina219 we
+	 * use a constant value.
 	 */
-	ret = i2c_smbus_write_word_swapped(client, INA2XX_CALIBRATION,
-				data->config->calibration_factor / shunt);
+	if (data->kind == ina226)
+		ina226_set_update_interval(data);
+	else
+		data->update_interval = HZ / INA2XX_CONVERSION_RATE;
+
+	if (data->rshunt <= 0 ||
+	    data->rshunt > data->config->calibration_factor)
+		return -ENODEV;
+
+	ret = ina2xx_init(data);
 	if (ret < 0) {
-		dev_err(dev,
-			"error writing to the calibration register: %d", ret);
+		dev_err(dev, "error configuring the device: %d\n", ret);
 		return -ENODEV;
 	}
 
-	data->client = client;
 	mutex_init(&data->update_lock);
 
+	data->groups[group++] = &ina2xx_group;
+	if (data->kind == ina226)
+		data->groups[group++] = &ina226_group;
+
 	hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name,
-							   data, ina2xx_groups);
+							   data, data->groups);
 	if (IS_ERR(hwmon_dev))
 		return PTR_ERR(hwmon_dev);
 
 	dev_info(dev, "power monitor %s (Rshunt = %li uOhm)\n",
-		 id->name, shunt);
+		 id->name, data->rshunt);
 
 	return 0;
 }
@@ -287,6 +538,7 @@ static const struct i2c_device_id ina2xx_id[] = {
 	{ "ina220", ina219 },
 	{ "ina226", ina226 },
 	{ "ina230", ina226 },
+	{ "ina231", ina226 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ina2xx_id);