diff options
Diffstat (limited to 'drivers/clocksource')
| -rw-r--r-- | drivers/clocksource/Kconfig | 12 | ||||
| -rw-r--r-- | drivers/clocksource/Makefile | 1 | ||||
| -rw-r--r-- | drivers/clocksource/arc_timer.c | 14 | ||||
| -rw-r--r-- | drivers/clocksource/mips-gic-timer.c | 18 | ||||
| -rw-r--r-- | drivers/clocksource/mxs_timer.c | 28 | ||||
| -rw-r--r-- | drivers/clocksource/timer-imx-gpt.c | 28 | ||||
| -rw-r--r-- | drivers/clocksource/timer-imx-tpm.c | 58 | ||||
| -rw-r--r-- | drivers/clocksource/timer-npcm7xx.c | 215 |
8 files changed, 302 insertions, 72 deletions
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig index 9ee2888275c1..dec0dd88ec15 100644 --- a/drivers/clocksource/Kconfig +++ b/drivers/clocksource/Kconfig @@ -133,6 +133,14 @@ config VT8500_TIMER help Enables support for the VT8500 driver. +config NPCM7XX_TIMER + bool "NPCM7xx timer driver" if COMPILE_TEST + depends on HAS_IOMEM + select CLKSRC_MMIO + help + Enable 24-bit TIMER0 and TIMER1 counters in the NPCM7xx architecture, + While TIMER0 serves as clockevent and TIMER1 serves as clocksource. + config CADENCE_TTC_TIMER bool "Cadence TTC timer driver" if COMPILE_TEST depends on COMMON_CLK @@ -442,8 +450,10 @@ config MTK_TIMER Support for Mediatek timer driver. config SPRD_TIMER - bool "Spreadtrum timer driver" if COMPILE_TEST + bool "Spreadtrum timer driver" if EXPERT depends on HAS_IOMEM + depends on (ARCH_SPRD || COMPILE_TEST) + default ARCH_SPRD select TIMER_OF help Enables support for the Spreadtrum timer driver. diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile index e8e76dfef00b..00caf37e52f9 100644 --- a/drivers/clocksource/Makefile +++ b/drivers/clocksource/Makefile @@ -56,6 +56,7 @@ obj-$(CONFIG_CLKSRC_NPS) += timer-nps.o obj-$(CONFIG_OXNAS_RPS_TIMER) += timer-oxnas-rps.o obj-$(CONFIG_OWL_TIMER) += owl-timer.o obj-$(CONFIG_SPRD_TIMER) += timer-sprd.o +obj-$(CONFIG_NPCM7XX_TIMER) += timer-npcm7xx.o obj-$(CONFIG_ARC_TIMERS) += arc_timer.o obj-$(CONFIG_ARM_ARCH_TIMER) += arm_arch_timer.o diff --git a/drivers/clocksource/arc_timer.c b/drivers/clocksource/arc_timer.c index 471b428d8034..20da9b1d7f7d 100644 --- a/drivers/clocksource/arc_timer.c +++ b/drivers/clocksource/arc_timer.c @@ -61,6 +61,20 @@ static u64 arc_read_gfrc(struct clocksource *cs) unsigned long flags; u32 l, h; + /* + * From a programming model pov, there seems to be just one instance of + * MCIP_CMD/MCIP_READBACK however micro-architecturally there's + * an instance PER ARC CORE (not per cluster), and there are dedicated + * hardware decode logic (per core) inside ARConnect to handle + * simultaneous read/write accesses from cores via those two registers. + * So several concurrent commands to ARConnect are OK if they are + * trying to access two different sub-components (like GFRC, + * inter-core interrupt, etc...). HW also supports simultaneously + * accessing GFRC by multiple cores. + * That's why it is safe to disable hard interrupts on the local CPU + * before access to GFRC instead of taking global MCIP spinlock + * defined in arch/arc/kernel/mcip.c + */ local_irq_save(flags); __mcip_cmd(CMD_GFRC_READ_LO, 0); diff --git a/drivers/clocksource/mips-gic-timer.c b/drivers/clocksource/mips-gic-timer.c index 986b6796b631..54f8a331b53a 100644 --- a/drivers/clocksource/mips-gic-timer.c +++ b/drivers/clocksource/mips-gic-timer.c @@ -5,6 +5,9 @@ * * Copyright (C) 2012 MIPS Technologies, Inc. All rights reserved. */ + +#define pr_fmt(fmt) "mips-gic-timer: " fmt + #include <linux/clk.h> #include <linux/clockchips.h> #include <linux/cpu.h> @@ -136,8 +139,7 @@ static int gic_clockevent_init(void) ret = setup_percpu_irq(gic_timer_irq, &gic_compare_irqaction); if (ret < 0) { - pr_err("GIC timer IRQ %d setup failed: %d\n", - gic_timer_irq, ret); + pr_err("IRQ %d setup failed (%d)\n", gic_timer_irq, ret); return ret; } @@ -176,7 +178,7 @@ static int __init __gic_clocksource_init(void) ret = clocksource_register_hz(&gic_clocksource, gic_frequency); if (ret < 0) - pr_warn("GIC: Unable to register clocksource\n"); + pr_warn("Unable to register clocksource\n"); return ret; } @@ -188,7 +190,7 @@ static int __init gic_clocksource_of_init(struct device_node *node) if (!mips_gic_present() || !node->parent || !of_device_is_compatible(node->parent, "mti,gic")) { - pr_warn("No DT definition for the mips gic driver\n"); + pr_warn("No DT definition\n"); return -ENXIO; } @@ -196,7 +198,7 @@ static int __init gic_clocksource_of_init(struct device_node *node) if (!IS_ERR(clk)) { ret = clk_prepare_enable(clk); if (ret < 0) { - pr_err("GIC failed to enable clock\n"); + pr_err("Failed to enable clock\n"); clk_put(clk); return ret; } @@ -204,12 +206,12 @@ static int __init gic_clocksource_of_init(struct device_node *node) gic_frequency = clk_get_rate(clk); } else if (of_property_read_u32(node, "clock-frequency", &gic_frequency)) { - pr_err("GIC frequency not specified.\n"); + pr_err("Frequency not specified\n"); return -EINVAL; } gic_timer_irq = irq_of_parse_and_map(node, 0); if (!gic_timer_irq) { - pr_err("GIC timer IRQ not specified.\n"); + pr_err("IRQ not specified\n"); return -EINVAL; } @@ -220,7 +222,7 @@ static int __init gic_clocksource_of_init(struct device_node *node) ret = gic_clockevent_init(); if (!ret && !IS_ERR(clk)) { if (clk_notifier_register(clk, &gic_clk_nb) < 0) - pr_warn("GIC: Unable to register clock notifier\n"); + pr_warn("Unable to register clock notifier\n"); } /* And finally start the counter */ diff --git a/drivers/clocksource/mxs_timer.c b/drivers/clocksource/mxs_timer.c index a03434e9fe8f..f6ddae30933f 100644 --- a/drivers/clocksource/mxs_timer.c +++ b/drivers/clocksource/mxs_timer.c @@ -1,24 +1,10 @@ -/* - * Copyright (C) 2000-2001 Deep Blue Solutions - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * Copyright (C) 2006-2007 Pavel Pisa (ppisa@pikron.com) - * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) - * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301, USA. - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright (C) 2000-2001 Deep Blue Solutions +// Copyright (C) 2002 Shane Nay (shane@minirl.com) +// Copyright (C) 2006-2007 Pavel Pisa (ppisa@pikron.com) +// Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) +// Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved. #include <linux/err.h> #include <linux/interrupt.h> diff --git a/drivers/clocksource/timer-imx-gpt.c b/drivers/clocksource/timer-imx-gpt.c index 6ec6d79b237c..165fbbb1c9a0 100644 --- a/drivers/clocksource/timer-imx-gpt.c +++ b/drivers/clocksource/timer-imx-gpt.c @@ -1,25 +1,9 @@ -/* - * linux/arch/arm/plat-mxc/time.c - * - * Copyright (C) 2000-2001 Deep Blue Solutions - * Copyright (C) 2002 Shane Nay (shane@minirl.com) - * Copyright (C) 2006-2007 Pavel Pisa (ppisa@pikron.com) - * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301, USA. - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright (C) 2000-2001 Deep Blue Solutions +// Copyright (C) 2002 Shane Nay (shane@minirl.com) +// Copyright (C) 2006-2007 Pavel Pisa (ppisa@pikron.com) +// Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de) #include <linux/interrupt.h> #include <linux/irq.h> diff --git a/drivers/clocksource/timer-imx-tpm.c b/drivers/clocksource/timer-imx-tpm.c index 21bffdcb2f20..b7aa2b817078 100644 --- a/drivers/clocksource/timer-imx-tpm.c +++ b/drivers/clocksource/timer-imx-tpm.c @@ -1,12 +1,7 @@ -/* - * Copyright 2016 Freescale Semiconductor, Inc. - * Copyright 2017 NXP - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - */ +// SPDX-License-Identifier: GPL-2.0+ +// +// Copyright 2016 Freescale Semiconductor, Inc. +// Copyright 2017 NXP #include <linux/clk.h> #include <linux/clockchips.h> @@ -17,9 +12,14 @@ #include <linux/of_irq.h> #include <linux/sched_clock.h> +#define TPM_PARAM 0x4 +#define TPM_PARAM_WIDTH_SHIFT 16 +#define TPM_PARAM_WIDTH_MASK (0xff << 16) #define TPM_SC 0x10 #define TPM_SC_CMOD_INC_PER_CNT (0x1 << 3) #define TPM_SC_CMOD_DIV_DEFAULT 0x3 +#define TPM_SC_CMOD_DIV_MAX 0x7 +#define TPM_SC_TOF_MASK (0x1 << 7) #define TPM_CNT 0x14 #define TPM_MOD 0x18 #define TPM_STATUS 0x1c @@ -29,8 +29,11 @@ #define TPM_C0SC_MODE_SHIFT 2 #define TPM_C0SC_MODE_MASK 0x3c #define TPM_C0SC_MODE_SW_COMPARE 0x4 +#define TPM_C0SC_CHF_MASK (0x1 << 7) #define TPM_C0V 0x24 +static int counter_width; +static int rating; static void __iomem *timer_base; static struct clock_event_device clockevent_tpm; @@ -83,10 +86,11 @@ static int __init tpm_clocksource_init(unsigned long rate) tpm_delay_timer.freq = rate; register_current_timer_delay(&tpm_delay_timer); - sched_clock_register(tpm_read_sched_clock, 32, rate); + sched_clock_register(tpm_read_sched_clock, counter_width, rate); return clocksource_mmio_init(timer_base + TPM_CNT, "imx-tpm", - rate, 200, 32, clocksource_mmio_readl_up); + rate, rating, counter_width, + clocksource_mmio_readl_up); } static int tpm_set_next_event(unsigned long delta, @@ -105,7 +109,7 @@ static int tpm_set_next_event(unsigned long delta, * of writing CNT registers which may cause the min_delta event got * missed, so we need add a ETIME check here in case it happened. */ - return (int)((next - now) <= 0) ? -ETIME : 0; + return (int)(next - now) <= 0 ? -ETIME : 0; } static int tpm_set_state_oneshot(struct clock_event_device *evt) @@ -139,7 +143,6 @@ static struct clock_event_device clockevent_tpm = { .set_state_oneshot = tpm_set_state_oneshot, .set_next_event = tpm_set_next_event, .set_state_shutdown = tpm_set_state_shutdown, - .rating = 200, }; static int __init tpm_clockevent_init(unsigned long rate, int irq) @@ -149,10 +152,11 @@ static int __init tpm_clockevent_init(unsigned long rate, int irq) ret = request_irq(irq, tpm_timer_interrupt, IRQF_TIMER | IRQF_IRQPOLL, "i.MX7ULP TPM Timer", &clockevent_tpm); + clockevent_tpm.rating = rating; clockevent_tpm.cpumask = cpumask_of(0); clockevent_tpm.irq = irq; - clockevents_config_and_register(&clockevent_tpm, - rate, 300, 0xfffffffe); + clockevents_config_and_register(&clockevent_tpm, rate, 300, + GENMASK(counter_width - 1, 1)); return ret; } @@ -179,7 +183,7 @@ static int __init tpm_timer_init(struct device_node *np) ipg = of_clk_get_by_name(np, "ipg"); per = of_clk_get_by_name(np, "per"); if (IS_ERR(ipg) || IS_ERR(per)) { - pr_err("tpm: failed to get igp or per clk\n"); + pr_err("tpm: failed to get ipg or per clk\n"); ret = -ENODEV; goto err_clk_get; } @@ -197,6 +201,11 @@ static int __init tpm_timer_init(struct device_node *np) goto err_per_clk_enable; } + counter_width = (readl(timer_base + TPM_PARAM) & TPM_PARAM_WIDTH_MASK) + >> TPM_PARAM_WIDTH_SHIFT; + /* use rating 200 for 32-bit counter and 150 for 16-bit counter */ + rating = counter_width == 0x20 ? 200 : 150; + /* * Initialize tpm module to a known state * 1) Counter disabled @@ -205,16 +214,25 @@ static int __init tpm_timer_init(struct device_node *np) * 4) Channel0 disabled * 5) DMA transfers disabled */ + /* make sure counter is disabled */ writel(0, timer_base + TPM_SC); + /* TOF is W1C */ + writel(TPM_SC_TOF_MASK, timer_base + TPM_SC); writel(0, timer_base + TPM_CNT); - writel(0, timer_base + TPM_C0SC); + /* CHF is W1C */ + writel(TPM_C0SC_CHF_MASK, timer_base + TPM_C0SC); - /* increase per cnt, div 8 by default */ - writel(TPM_SC_CMOD_INC_PER_CNT | TPM_SC_CMOD_DIV_DEFAULT, + /* + * increase per cnt, + * div 8 for 32-bit counter and div 128 for 16-bit counter + */ + writel(TPM_SC_CMOD_INC_PER_CNT | + (counter_width == 0x20 ? + TPM_SC_CMOD_DIV_DEFAULT : TPM_SC_CMOD_DIV_MAX), timer_base + TPM_SC); /* set MOD register to maximum for free running mode */ - writel(0xffffffff, timer_base + TPM_MOD); + writel(GENMASK(counter_width - 1, 0), timer_base + TPM_MOD); rate = clk_get_rate(per) >> 3; ret = tpm_clocksource_init(rate); diff --git a/drivers/clocksource/timer-npcm7xx.c b/drivers/clocksource/timer-npcm7xx.c new file mode 100644 index 000000000000..7a9bb5532d99 --- /dev/null +++ b/drivers/clocksource/timer-npcm7xx.c @@ -0,0 +1,215 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2014-2018 Nuvoton Technologies tomer.maimon@nuvoton.com + * All rights reserved. + * + * Copyright 2017 Google, Inc. + */ + +#include <linux/kernel.h> +#include <linux/sched.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <linux/clockchips.h> +#include <linux/of_irq.h> +#include <linux/of_address.h> +#include "timer-of.h" + +/* Timers registers */ +#define NPCM7XX_REG_TCSR0 0x0 /* Timer 0 Control and Status Register */ +#define NPCM7XX_REG_TICR0 0x8 /* Timer 0 Initial Count Register */ +#define NPCM7XX_REG_TCSR1 0x4 /* Timer 1 Control and Status Register */ +#define NPCM7XX_REG_TICR1 0xc /* Timer 1 Initial Count Register */ +#define NPCM7XX_REG_TDR1 0x14 /* Timer 1 Data Register */ +#define NPCM7XX_REG_TISR 0x18 /* Timer Interrupt Status Register */ + +/* Timers control */ +#define NPCM7XX_Tx_RESETINT 0x1f +#define NPCM7XX_Tx_PERIOD BIT(27) +#define NPCM7XX_Tx_INTEN BIT(29) +#define NPCM7XX_Tx_COUNTEN BIT(30) +#define NPCM7XX_Tx_ONESHOT 0x0 +#define NPCM7XX_Tx_OPER GENMASK(3, 27) +#define NPCM7XX_Tx_MIN_PRESCALE 0x1 +#define NPCM7XX_Tx_TDR_MASK_BITS 24 +#define NPCM7XX_Tx_MAX_CNT 0xFFFFFF +#define NPCM7XX_T0_CLR_INT 0x1 +#define NPCM7XX_Tx_CLR_CSR 0x0 + +/* Timers operating mode */ +#define NPCM7XX_START_PERIODIC_Tx (NPCM7XX_Tx_PERIOD | NPCM7XX_Tx_COUNTEN | \ + NPCM7XX_Tx_INTEN | \ + NPCM7XX_Tx_MIN_PRESCALE) + +#define NPCM7XX_START_ONESHOT_Tx (NPCM7XX_Tx_ONESHOT | NPCM7XX_Tx_COUNTEN | \ + NPCM7XX_Tx_INTEN | \ + NPCM7XX_Tx_MIN_PRESCALE) + +#define NPCM7XX_START_Tx (NPCM7XX_Tx_COUNTEN | NPCM7XX_Tx_PERIOD | \ + NPCM7XX_Tx_MIN_PRESCALE) + +#define NPCM7XX_DEFAULT_CSR (NPCM7XX_Tx_CLR_CSR | NPCM7XX_Tx_MIN_PRESCALE) + +static int npcm7xx_timer_resume(struct clock_event_device *evt) +{ + struct timer_of *to = to_timer_of(evt); + u32 val; + + val = readl(timer_of_base(to) + NPCM7XX_REG_TCSR0); + val |= NPCM7XX_Tx_COUNTEN; + writel(val, timer_of_base(to) + NPCM7XX_REG_TCSR0); + + return 0; +} + +static int npcm7xx_timer_shutdown(struct clock_event_device *evt) +{ + struct timer_of *to = to_timer_of(evt); + u32 val; + + val = readl(timer_of_base(to) + NPCM7XX_REG_TCSR0); + val &= ~NPCM7XX_Tx_COUNTEN; + writel(val, timer_of_base(to) + NPCM7XX_REG_TCSR0); + + return 0; +} + +static int npcm7xx_timer_oneshot(struct clock_event_device *evt) +{ + struct timer_of *to = to_timer_of(evt); + u32 val; + + val = readl(timer_of_base(to) + NPCM7XX_REG_TCSR0); + val &= ~NPCM7XX_Tx_OPER; + + val = readl(timer_of_base(to) + NPCM7XX_REG_TCSR0); + val |= NPCM7XX_START_ONESHOT_Tx; + writel(val, timer_of_base(to) + NPCM7XX_REG_TCSR0); + + return 0; +} + +static int npcm7xx_timer_periodic(struct clock_event_device *evt) +{ + struct timer_of *to = to_timer_of(evt); + u32 val; + + val = readl(timer_of_base(to) + NPCM7XX_REG_TCSR0); + val &= ~NPCM7XX_Tx_OPER; + + writel(timer_of_period(to), timer_of_base(to) + NPCM7XX_REG_TICR0); + val |= NPCM7XX_START_PERIODIC_Tx; + + writel(val, timer_of_base(to) + NPCM7XX_REG_TCSR0); + + return 0; +} + +static int npcm7xx_clockevent_set_next_event(unsigned long evt, + struct clock_event_device *clk) +{ + struct timer_of *to = to_timer_of(clk); + u32 val; + + writel(evt, timer_of_base(to) + NPCM7XX_REG_TICR0); + val = readl(timer_of_base(to) + NPCM7XX_REG_TCSR0); + val |= NPCM7XX_START_Tx; + writel(val, timer_of_base(to) + NPCM7XX_REG_TCSR0); + + return 0; +} + +static irqreturn_t npcm7xx_timer0_interrupt(int irq, void *dev_id) +{ + struct clock_event_device *evt = (struct clock_event_device *)dev_id; + struct timer_of *to = to_timer_of(evt); + + writel(NPCM7XX_T0_CLR_INT, timer_of_base(to) + NPCM7XX_REG_TISR); + + evt->event_handler(evt); + + return IRQ_HANDLED; +} + +static struct timer_of npcm7xx_to = { + .flags = TIMER_OF_IRQ | TIMER_OF_BASE | TIMER_OF_CLOCK, + + .clkevt = { + .name = "npcm7xx-timer0", + .features = CLOCK_EVT_FEAT_PERIODIC | + CLOCK_EVT_FEAT_ONESHOT, + .set_next_event = npcm7xx_clockevent_set_next_event, + .set_state_shutdown = npcm7xx_timer_shutdown, + .set_state_periodic = npcm7xx_timer_periodic, + .set_state_oneshot = npcm7xx_timer_oneshot, + .tick_resume = npcm7xx_timer_resume, + .rating = 300, + }, + + .of_irq = { + .handler = npcm7xx_timer0_interrupt, + .flags = IRQF_TIMER | IRQF_IRQPOLL, + }, +}; + +static void __init npcm7xx_clockevents_init(void) +{ + writel(NPCM7XX_DEFAULT_CSR, + timer_of_base(&npcm7xx_to) + NPCM7XX_REG_TCSR0); + + writel(NPCM7XX_Tx_RESETINT, + timer_of_base(&npcm7xx_to) + NPCM7XX_REG_TISR); + + npcm7xx_to.clkevt.cpumask = cpumask_of(0); + clockevents_config_and_register(&npcm7xx_to.clkevt, + timer_of_rate(&npcm7xx_to), + 0x1, NPCM7XX_Tx_MAX_CNT); +} + +static void __init npcm7xx_clocksource_init(void) +{ + u32 val; + + writel(NPCM7XX_DEFAULT_CSR, + timer_of_base(&npcm7xx_to) + NPCM7XX_REG_TCSR1); + writel(NPCM7XX_Tx_MAX_CNT, + timer_of_base(&npcm7xx_to) + NPCM7XX_REG_TICR1); + + val = readl(timer_of_base(&npcm7xx_to) + NPCM7XX_REG_TCSR1); + val |= NPCM7XX_START_Tx; + writel(val, timer_of_base(&npcm7xx_to) + NPCM7XX_REG_TCSR1); + + clocksource_mmio_init(timer_of_base(&npcm7xx_to) + + NPCM7XX_REG_TDR1, + "npcm7xx-timer1", timer_of_rate(&npcm7xx_to), + 200, (unsigned int)NPCM7XX_Tx_TDR_MASK_BITS, + clocksource_mmio_readl_down); +} + +static int __init npcm7xx_timer_init(struct device_node *np) +{ + int ret; + + ret = timer_of_init(np, &npcm7xx_to); + if (ret) + return ret; + + /* Clock input is divided by PRESCALE + 1 before it is fed */ + /* to the counter */ + npcm7xx_to.of_clk.rate = npcm7xx_to.of_clk.rate / + (NPCM7XX_Tx_MIN_PRESCALE + 1); + + npcm7xx_clocksource_init(); + npcm7xx_clockevents_init(); + + pr_info("Enabling NPCM7xx clocksource timer base: %px, IRQ: %d ", + timer_of_base(&npcm7xx_to), timer_of_irq(&npcm7xx_to)); + + return 0; +} + +TIMER_OF_DECLARE(npcm7xx, "nuvoton,npcm750-timer", npcm7xx_timer_init); + |