diff options
Diffstat (limited to 'arch/x86/include/asm/voyager.h')
| -rw-r--r-- | arch/x86/include/asm/voyager.h | 529 |
1 files changed, 0 insertions, 529 deletions
diff --git a/arch/x86/include/asm/voyager.h b/arch/x86/include/asm/voyager.h deleted file mode 100644 index b3e647307625..000000000000 --- a/arch/x86/include/asm/voyager.h +++ /dev/null @@ -1,529 +0,0 @@ -/* Copyright (C) 1999,2001 - * - * Author: J.E.J.Bottomley@HansenPartnership.com - * - * Standard include definitions for the NCR Voyager system */ - -#undef VOYAGER_DEBUG -#undef VOYAGER_CAT_DEBUG - -#ifdef VOYAGER_DEBUG -#define VDEBUG(x) printk x -#else -#define VDEBUG(x) -#endif - -/* There are three levels of voyager machine: 3,4 and 5. The rule is - * if it's less than 3435 it's a Level 3 except for a 3360 which is - * a level 4. A 3435 or above is a Level 5 */ -#define VOYAGER_LEVEL5_AND_ABOVE 0x3435 -#define VOYAGER_LEVEL4 0x3360 - -/* The L4 DINO ASIC */ -#define VOYAGER_DINO 0x43 - -/* voyager ports in standard I/O space */ -#define VOYAGER_MC_SETUP 0x96 - - -#define VOYAGER_CAT_CONFIG_PORT 0x97 -# define VOYAGER_CAT_DESELECT 0xff -#define VOYAGER_SSPB_RELOCATION_PORT 0x98 - -/* Valid CAT controller commands */ -/* start instruction register cycle */ -#define VOYAGER_CAT_IRCYC 0x01 -/* start data register cycle */ -#define VOYAGER_CAT_DRCYC 0x02 -/* move to execute state */ -#define VOYAGER_CAT_RUN 0x0F -/* end operation */ -#define VOYAGER_CAT_END 0x80 -/* hold in idle state */ -#define VOYAGER_CAT_HOLD 0x90 -/* single step an "intest" vector */ -#define VOYAGER_CAT_STEP 0xE0 -/* return cat controller to CLEMSON mode */ -#define VOYAGER_CAT_CLEMSON 0xFF - -/* the default cat command header */ -#define VOYAGER_CAT_HEADER 0x7F - -/* the range of possible CAT module ids in the system */ -#define VOYAGER_MIN_MODULE 0x10 -#define VOYAGER_MAX_MODULE 0x1f - -/* The voyager registers per asic */ -#define VOYAGER_ASIC_ID_REG 0x00 -#define VOYAGER_ASIC_TYPE_REG 0x01 -/* the sub address registers can be made auto incrementing on reads */ -#define VOYAGER_AUTO_INC_REG 0x02 -# define VOYAGER_AUTO_INC 0x04 -# define VOYAGER_NO_AUTO_INC 0xfb -#define VOYAGER_SUBADDRDATA 0x03 -#define VOYAGER_SCANPATH 0x05 -# define VOYAGER_CONNECT_ASIC 0x01 -# define VOYAGER_DISCONNECT_ASIC 0xfe -#define VOYAGER_SUBADDRLO 0x06 -#define VOYAGER_SUBADDRHI 0x07 -#define VOYAGER_SUBMODSELECT 0x08 -#define VOYAGER_SUBMODPRESENT 0x09 - -#define VOYAGER_SUBADDR_LO 0xff -#define VOYAGER_SUBADDR_HI 0xffff - -/* the maximum size of a scan path -- used to form instructions */ -#define VOYAGER_MAX_SCAN_PATH 0x100 -/* the biggest possible register size (in bytes) */ -#define VOYAGER_MAX_REG_SIZE 4 - -/* Total number of possible modules (including submodules) */ -#define VOYAGER_MAX_MODULES 16 -/* Largest number of asics per module */ -#define VOYAGER_MAX_ASICS_PER_MODULE 7 - -/* the CAT asic of each module is always the first one */ -#define VOYAGER_CAT_ID 0 -#define VOYAGER_PSI 0x1a - -/* voyager instruction operations and registers */ -#define VOYAGER_READ_CONFIG 0x1 -#define VOYAGER_WRITE_CONFIG 0x2 -#define VOYAGER_BYPASS 0xff - -typedef struct voyager_asic { - __u8 asic_addr; /* ASIC address; Level 4 */ - __u8 asic_type; /* ASIC type */ - __u8 asic_id; /* ASIC id */ - __u8 jtag_id[4]; /* JTAG id */ - __u8 asic_location; /* Location within scan path; start w/ 0 */ - __u8 bit_location; /* Location within bit stream; start w/ 0 */ - __u8 ireg_length; /* Instruction register length */ - __u16 subaddr; /* Amount of sub address space */ - struct voyager_asic *next; /* Next asic in linked list */ -} voyager_asic_t; - -typedef struct voyager_module { - __u8 module_addr; /* Module address */ - __u8 scan_path_connected; /* Scan path connected */ - __u16 ee_size; /* Size of the EEPROM */ - __u16 num_asics; /* Number of Asics */ - __u16 inst_bits; /* Instruction bits in the scan path */ - __u16 largest_reg; /* Largest register in the scan path */ - __u16 smallest_reg; /* Smallest register in the scan path */ - voyager_asic_t *asic; /* First ASIC in scan path (CAT_I) */ - struct voyager_module *submodule; /* Submodule pointer */ - struct voyager_module *next; /* Next module in linked list */ -} voyager_module_t; - -typedef struct voyager_eeprom_hdr { - __u8 module_id[4]; - __u8 version_id; - __u8 config_id; - __u16 boundry_id; /* boundary scan id */ - __u16 ee_size; /* size of EEPROM */ - __u8 assembly[11]; /* assembly # */ - __u8 assembly_rev; /* assembly rev */ - __u8 tracer[4]; /* tracer number */ - __u16 assembly_cksum; /* asm checksum */ - __u16 power_consump; /* pwr requirements */ - __u16 num_asics; /* number of asics */ - __u16 bist_time; /* min. bist time */ - __u16 err_log_offset; /* error log offset */ - __u16 scan_path_offset;/* scan path offset */ - __u16 cct_offset; - __u16 log_length; /* length of err log */ - __u16 xsum_end; /* offset to end of - checksum */ - __u8 reserved[4]; - __u8 sflag; /* starting sentinal */ - __u8 part_number[13]; /* prom part number */ - __u8 version[10]; /* version number */ - __u8 signature[8]; - __u16 eeprom_chksum; - __u32 data_stamp_offset; - __u8 eflag ; /* ending sentinal */ -} __attribute__((packed)) voyager_eprom_hdr_t; - - - -#define VOYAGER_EPROM_SIZE_OFFSET \ - ((__u16)(&(((voyager_eprom_hdr_t *)0)->ee_size))) -#define VOYAGER_XSUM_END_OFFSET 0x2a - -/* the following three definitions are for internal table layouts - * in the module EPROMs. We really only care about the IDs and - * offsets */ -typedef struct voyager_sp_table { - __u8 asic_id; - __u8 bypass_flag; - __u16 asic_data_offset; - __u16 config_data_offset; -} __attribute__((packed)) voyager_sp_table_t; - -typedef struct voyager_jtag_table { - __u8 icode[4]; - __u8 runbist[4]; - __u8 intest[4]; - __u8 samp_preld[4]; - __u8 ireg_len; -} __attribute__((packed)) voyager_jtt_t; - -typedef struct voyager_asic_data_table { - __u8 jtag_id[4]; - __u16 length_bsr; - __u16 length_bist_reg; - __u32 bist_clk; - __u16 subaddr_bits; - __u16 seed_bits; - __u16 sig_bits; - __u16 jtag_offset; -} __attribute__((packed)) voyager_at_t; - -/* Voyager Interrupt Controller (VIC) registers */ - -/* Base to add to Cross Processor Interrupts (CPIs) when triggering - * the CPU IRQ line */ -/* register defines for the WCBICs (one per processor) */ -#define VOYAGER_WCBIC0 0x41 /* bus A node P1 processor 0 */ -#define VOYAGER_WCBIC1 0x49 /* bus A node P1 processor 1 */ -#define VOYAGER_WCBIC2 0x51 /* bus A node P2 processor 0 */ -#define VOYAGER_WCBIC3 0x59 /* bus A node P2 processor 1 */ -#define VOYAGER_WCBIC4 0x61 /* bus B node P1 processor 0 */ -#define VOYAGER_WCBIC5 0x69 /* bus B node P1 processor 1 */ -#define VOYAGER_WCBIC6 0x71 /* bus B node P2 processor 0 */ -#define VOYAGER_WCBIC7 0x79 /* bus B node P2 processor 1 */ - - -/* top of memory registers */ -#define VOYAGER_WCBIC_TOM_L 0x4 -#define VOYAGER_WCBIC_TOM_H 0x5 - -/* register defines for Voyager Memory Contol (VMC) - * these are present on L4 machines only */ -#define VOYAGER_VMC1 0x81 -#define VOYAGER_VMC2 0x91 -#define VOYAGER_VMC3 0xa1 -#define VOYAGER_VMC4 0xb1 - -/* VMC Ports */ -#define VOYAGER_VMC_MEMORY_SETUP 0x9 -# define VMC_Interleaving 0x01 -# define VMC_4Way 0x02 -# define VMC_EvenCacheLines 0x04 -# define VMC_HighLine 0x08 -# define VMC_Start0_Enable 0x20 -# define VMC_Start1_Enable 0x40 -# define VMC_Vremap 0x80 -#define VOYAGER_VMC_BANK_DENSITY 0xa -# define VMC_BANK_EMPTY 0 -# define VMC_BANK_4MB 1 -# define VMC_BANK_16MB 2 -# define VMC_BANK_64MB 3 -# define VMC_BANK0_MASK 0x03 -# define VMC_BANK1_MASK 0x0C -# define VMC_BANK2_MASK 0x30 -# define VMC_BANK3_MASK 0xC0 - -/* Magellan Memory Controller (MMC) defines - present on L5 */ -#define VOYAGER_MMC_ASIC_ID 1 -/* the two memory modules corresponding to memory cards in the system */ -#define VOYAGER_MMC_MEMORY0_MODULE 0x14 -#define VOYAGER_MMC_MEMORY1_MODULE 0x15 -/* the Magellan Memory Address (MMA) defines */ -#define VOYAGER_MMA_ASIC_ID 2 - -/* Submodule number for the Quad Baseboard */ -#define VOYAGER_QUAD_BASEBOARD 1 - -/* ASIC defines for the Quad Baseboard */ -#define VOYAGER_QUAD_QDATA0 1 -#define VOYAGER_QUAD_QDATA1 2 -#define VOYAGER_QUAD_QABC 3 - -/* Useful areas in extended CMOS */ -#define VOYAGER_PROCESSOR_PRESENT_MASK 0x88a -#define VOYAGER_MEMORY_CLICKMAP 0xa23 -#define VOYAGER_DUMP_LOCATION 0xb1a - -/* SUS In Control bit - used to tell SUS that we don't need to be - * babysat anymore */ -#define VOYAGER_SUS_IN_CONTROL_PORT 0x3ff -# define VOYAGER_IN_CONTROL_FLAG 0x80 - -/* Voyager PSI defines */ -#define VOYAGER_PSI_STATUS_REG 0x08 -# define PSI_DC_FAIL 0x01 -# define PSI_MON 0x02 -# define PSI_FAULT 0x04 -# define PSI_ALARM 0x08 -# define PSI_CURRENT 0x10 -# define PSI_DVM 0x20 -# define PSI_PSCFAULT 0x40 -# define PSI_STAT_CHG 0x80 - -#define VOYAGER_PSI_SUPPLY_REG 0x8000 - /* read */ -# define PSI_FAIL_DC 0x01 -# define PSI_FAIL_AC 0x02 -# define PSI_MON_INT 0x04 -# define PSI_SWITCH_OFF 0x08 -# define PSI_HX_OFF 0x10 -# define PSI_SECURITY 0x20 -# define PSI_CMOS_BATT_LOW 0x40 -# define PSI_CMOS_BATT_FAIL 0x80 - /* write */ -# define PSI_CLR_SWITCH_OFF 0x13 -# define PSI_CLR_HX_OFF 0x14 -# define PSI_CLR_CMOS_BATT_FAIL 0x17 - -#define VOYAGER_PSI_MASK 0x8001 -# define PSI_MASK_MASK 0x10 - -#define VOYAGER_PSI_AC_FAIL_REG 0x8004 -#define AC_FAIL_STAT_CHANGE 0x80 - -#define VOYAGER_PSI_GENERAL_REG 0x8007 - /* read */ -# define PSI_SWITCH_ON 0x01 -# define PSI_SWITCH_ENABLED 0x02 -# define PSI_ALARM_ENABLED 0x08 -# define PSI_SECURE_ENABLED 0x10 -# define PSI_COLD_RESET 0x20 -# define PSI_COLD_START 0x80 - /* write */ -# define PSI_POWER_DOWN 0x10 -# define PSI_SWITCH_DISABLE 0x01 -# define PSI_SWITCH_ENABLE 0x11 -# define PSI_CLEAR 0x12 -# define PSI_ALARM_DISABLE 0x03 -# define PSI_ALARM_ENABLE 0x13 -# define PSI_CLEAR_COLD_RESET 0x05 -# define PSI_SET_COLD_RESET 0x15 -# define PSI_CLEAR_COLD_START 0x07 -# define PSI_SET_COLD_START 0x17 - - - -struct voyager_bios_info { - __u8 len; - __u8 major; - __u8 minor; - __u8 debug; - __u8 num_classes; - __u8 class_1; - __u8 class_2; -}; - -/* The following structures and definitions are for the Kernel/SUS - * interface these are needed to find out how SUS initialised any Quad - * boards in the system */ - -#define NUMBER_OF_MC_BUSSES 2 -#define SLOTS_PER_MC_BUS 8 -#define MAX_CPUS 16 /* 16 way CPU system */ -#define MAX_PROCESSOR_BOARDS 4 /* 4 processor slot system */ -#define MAX_CACHE_LEVELS 4 /* # of cache levels supported */ -#define MAX_SHARED_CPUS 4 /* # of CPUs that can share a LARC */ -#define NUMBER_OF_POS_REGS 8 - -typedef struct { - __u8 MC_Slot; - __u8 POS_Values[NUMBER_OF_POS_REGS]; -} __attribute__((packed)) MC_SlotInformation_t; - -struct QuadDescription { - __u8 Type; /* for type 0 (DYADIC or MONADIC) all fields - * will be zero except for slot */ - __u8 StructureVersion; - __u32 CPI_BaseAddress; - __u32 LARC_BankSize; - __u32 LocalMemoryStateBits; - __u8 Slot; /* Processor slots 1 - 4 */ -} __attribute__((packed)); - -struct ProcBoardInfo { - __u8 Type; - __u8 StructureVersion; - __u8 NumberOfBoards; - struct QuadDescription QuadData[MAX_PROCESSOR_BOARDS]; -} __attribute__((packed)); - -struct CacheDescription { - __u8 Level; - __u32 TotalSize; - __u16 LineSize; - __u8 Associativity; - __u8 CacheType; - __u8 WriteType; - __u8 Number_CPUs_SharedBy; - __u8 Shared_CPUs_Hardware_IDs[MAX_SHARED_CPUS]; - -} __attribute__((packed)); - -struct CPU_Description { - __u8 CPU_HardwareId; - char *FRU_String; - __u8 NumberOfCacheLevels; - struct CacheDescription CacheLevelData[MAX_CACHE_LEVELS]; -} __attribute__((packed)); - -struct CPU_Info { - __u8 Type; - __u8 StructureVersion; - __u8 NumberOf_CPUs; - struct CPU_Description CPU_Data[MAX_CPUS]; -} __attribute__((packed)); - - -/* - * This structure will be used by SUS and the OS. - * The assumption about this structure is that no blank space is - * packed in it by our friend the compiler. - */ -typedef struct { - __u8 Mailbox_SUS; /* Written to by SUS to give - commands/response to the OS */ - __u8 Mailbox_OS; /* Written to by the OS to give - commands/response to SUS */ - __u8 SUS_MailboxVersion; /* Tells the OS which iteration of the - interface SUS supports */ - __u8 OS_MailboxVersion; /* Tells SUS which iteration of the - interface the OS supports */ - __u32 OS_Flags; /* Flags set by the OS as info for - SUS */ - __u32 SUS_Flags; /* Flags set by SUS as info - for the OS */ - __u32 WatchDogPeriod; /* Watchdog period (in seconds) which - the DP uses to see if the OS - is dead */ - __u32 WatchDogCount; /* Updated by the OS on every tic. */ - __u32 MemoryFor_SUS_ErrorLog; /* Flat 32 bit address which tells SUS - where to stuff the SUS error log - on a dump */ - MC_SlotInformation_t MC_SlotInfo[NUMBER_OF_MC_BUSSES*SLOTS_PER_MC_BUS]; - /* Storage for MCA POS data */ - /* All new SECOND_PASS_INTERFACE fields added from this point */ - struct ProcBoardInfo *BoardData; - struct CPU_Info *CPU_Data; - /* All new fields must be added from this point */ -} Voyager_KernelSUS_Mbox_t; - -/* structure for finding the right memory address to send a QIC CPI to */ -struct voyager_qic_cpi { - /* Each cache line (32 bytes) can trigger a cpi. The cpi - * read/write may occur anywhere in the cache line---pick the - * middle to be safe */ - struct { - __u32 pad1[3]; - __u32 cpi; - __u32 pad2[4]; - } qic_cpi[8]; -}; - -struct voyager_status { - __u32 power_fail:1; - __u32 switch_off:1; - __u32 request_from_kernel:1; -}; - -struct voyager_psi_regs { - __u8 cat_id; - __u8 cat_dev; - __u8 cat_control; - __u8 subaddr; - __u8 dummy4; - __u8 checkbit; - __u8 subaddr_low; - __u8 subaddr_high; - __u8 intstatus; - __u8 stat1; - __u8 stat3; - __u8 fault; - __u8 tms; - __u8 gen; - __u8 sysconf; - __u8 dummy15; -}; - -struct voyager_psi_subregs { - __u8 supply; - __u8 mask; - __u8 present; - __u8 DCfail; - __u8 ACfail; - __u8 fail; - __u8 UPSfail; - __u8 genstatus; -}; - -struct voyager_psi { - struct voyager_psi_regs regs; - struct voyager_psi_subregs subregs; -}; - -struct voyager_SUS { -#define VOYAGER_DUMP_BUTTON_NMI 0x1 -#define VOYAGER_SUS_VALID 0x2 -#define VOYAGER_SYSINT_COMPLETE 0x3 - __u8 SUS_mbox; -#define VOYAGER_NO_COMMAND 0x0 -#define VOYAGER_IGNORE_DUMP 0x1 -#define VOYAGER_DO_DUMP 0x2 -#define VOYAGER_SYSINT_HANDSHAKE 0x3 -#define VOYAGER_DO_MEM_DUMP 0x4 -#define VOYAGER_SYSINT_WAS_RECOVERED 0x5 - __u8 kernel_mbox; -#define VOYAGER_MAILBOX_VERSION 0x10 - __u8 SUS_version; - __u8 kernel_version; -#define VOYAGER_OS_HAS_SYSINT 0x1 -#define VOYAGER_OS_IN_PROGRESS 0x2 -#define VOYAGER_UPDATING_WDPERIOD 0x4 - __u32 kernel_flags; -#define VOYAGER_SUS_BOOTING 0x1 -#define VOYAGER_SUS_IN_PROGRESS 0x2 - __u32 SUS_flags; - __u32 watchdog_period; - __u32 watchdog_count; - __u32 SUS_errorlog; - /* lots of system configuration stuff under here */ -}; - -/* Variables exported by voyager_smp */ -extern __u32 voyager_extended_vic_processors; -extern __u32 voyager_allowed_boot_processors; -extern __u32 voyager_quad_processors; -extern struct voyager_qic_cpi *voyager_quad_cpi_addr[NR_CPUS]; -extern struct voyager_SUS *voyager_SUS; - -/* variables exported always */ -extern struct task_struct *voyager_thread; -extern int voyager_level; -extern struct voyager_status voyager_status; - -/* functions exported by the voyager and voyager_smp modules */ -extern int voyager_cat_readb(__u8 module, __u8 asic, int reg); -extern void voyager_cat_init(void); -extern void voyager_detect(struct voyager_bios_info *); -extern void voyager_trap_init(void); -extern void voyager_setup_irqs(void); -extern int voyager_memory_detect(int region, __u32 *addr, __u32 *length); -extern void voyager_smp_intr_init(void); -extern __u8 voyager_extended_cmos_read(__u16 cmos_address); -extern void voyager_smp_dump(void); -extern void voyager_timer_interrupt(void); -extern void smp_local_timer_interrupt(void); -extern void voyager_power_off(void); -extern void smp_voyager_power_off(void *dummy); -extern void voyager_restart(void); -extern void voyager_cat_power_off(void); -extern void voyager_cat_do_common_interrupt(void); -extern void voyager_handle_nmi(void); -extern void voyager_smp_intr_init(void); -/* Commands for the following are */ -#define VOYAGER_PSI_READ 0 -#define VOYAGER_PSI_WRITE 1 -#define VOYAGER_PSI_SUBREAD 2 -#define VOYAGER_PSI_SUBWRITE 3 -extern void voyager_cat_psi(__u8, __u16, __u8 *); |