1 files changed, 0 insertions, 83 deletions
diff --git a/arch/cris/include/uapi/asm/etraxgpio.h b/arch/cris/include/uapi/asm/etraxgpio.h
deleted file mode 100644
index 10ab0dd45bfe..000000000000
--- a/arch/cris/include/uapi/asm/etraxgpio.h
+++ /dev/null
@@ -1,83 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
-/*
- * The following devices are accessible using this driver using
- * GPIO_MAJOR (120) and a couple of minor numbers.
- *
- * For ETRAX 100LX (CONFIG_ETRAX_ARCH_V10):
- * /dev/gpioa  minor 0, 8 bit GPIO, each bit can change direction
- * /dev/gpiob  minor 1, 8 bit GPIO, each bit can change direction
- * /dev/leds   minor 2, Access to leds depending on kernelconfig
- * /dev/gpiog  minor 3
- *       g0dir, g8_15dir, g16_23dir, g24 dir configurable in R_GEN_CONFIG
- *       g1-g7 and g25-g31 is both input and outputs but on different pins
- *       Also note that some bits change pins depending on what interfaces
- *       are enabled.
- */
-#ifndef _ASM_ETRAXGPIO_H
-#define _ASM_ETRAXGPIO_H
-
-#define GPIO_MINOR_FIRST 0
-
-#define ETRAXGPIO_IOCTYPE 43
-
-/* etraxgpio _IOC_TYPE, bits 8 to 15 in ioctl cmd */
-#define GPIO_MINOR_A 0
-#define GPIO_MINOR_B 1
-#define GPIO_MINOR_LEDS 2
-#define GPIO_MINOR_G 3
-#define GPIO_MINOR_LAST 3
-#define GPIO_MINOR_LAST_REAL GPIO_MINOR_LAST
-
-
-/* supported ioctl _IOC_NR's */
-
-#define IO_READBITS  0x1  /* read and return current port bits (obsolete) */
-#define IO_SETBITS   0x2  /* set the bits marked by 1 in the argument */
-#define IO_CLRBITS   0x3  /* clear the bits marked by 1 in the argument */
-
-/* the alarm is waited for by select() */
-
-#define IO_HIGHALARM 0x4  /* set alarm on high for bits marked by 1 */
-#define IO_LOWALARM  0x5  /* set alarm on low for bits marked by 1 */
-#define IO_CLRALARM  0x6  /* clear alarm for bits marked by 1 */
-
-/* LED ioctl */
-#define IO_LEDACTIVE_SET 0x7 /* set active led
-                              * 0=off, 1=green, 2=red, 3=yellow */
-
-/* GPIO direction ioctl's */
-#define IO_READDIR    0x8  /* Read direction 0=input 1=output  (obsolete) */
-#define IO_SETINPUT   0x9  /* Set direction for bits set, 0=unchanged 1=input,
-                              returns mask with current inputs (obsolete) */
-#define IO_SETOUTPUT  0xA  /* Set direction for bits set, 0=unchanged 1=output,
-                              returns mask with current outputs (obsolete)*/
-
-/* LED ioctl extended */
-#define IO_LED_SETBIT 0xB
-#define IO_LED_CLRBIT 0xC
-
-/* SHUTDOWN ioctl */
-#define IO_SHUTDOWN   0xD
-#define IO_GET_PWR_BT 0xE
-
-/* Bit toggling in driver settings */
-/* bit set in low byte0 is CLK mask (0x00FF),
-   bit set in byte1 is DATA mask    (0xFF00)
-   msb, data_mask[7:0] , clk_mask[7:0]
- */
-#define IO_CFG_WRITE_MODE 0xF
-#define IO_CFG_WRITE_MODE_VALUE(msb, data_mask, clk_mask) \
-	( (((msb)&1) << 16) | (((data_mask) &0xFF) << 8) | ((clk_mask) & 0xFF) )
-
-/* The following 4 ioctl's take a pointer as argument and handles
- * 32 bit ports (port G) properly.
- * These replaces IO_READBITS,IO_SETINPUT AND IO_SETOUTPUT
- */
-#define IO_READ_INBITS   0x10 /* *arg is result of reading the input pins */
-#define IO_READ_OUTBITS  0x11 /* *arg is result of reading the output shadow */
-#define IO_SETGET_INPUT  0x12 /* bits set in *arg is set to input, */
-			      /* *arg updated with current input pins. */
-#define IO_SETGET_OUTPUT 0x13 /* bits set in *arg is set to output, */
-			      /* *arg updated with current output pins. */
-
-#endif