diff options
Diffstat (limited to 'arch/cris/arch-v32/drivers/Kconfig')
| -rw-r--r-- | arch/cris/arch-v32/drivers/Kconfig | 263 |
1 files changed, 0 insertions, 263 deletions
diff --git a/arch/cris/arch-v32/drivers/Kconfig b/arch/cris/arch-v32/drivers/Kconfig deleted file mode 100644 index 4d2d744bced2..000000000000 --- a/arch/cris/arch-v32/drivers/Kconfig +++ /dev/null @@ -1,263 +0,0 @@ -# SPDX-License-Identifier: GPL-2.0 -if ETRAX_ARCH_V32 - -config ETRAX_ETHERNET - bool "Ethernet support" - depends on ETRAX_ARCH_V32 && NETDEVICES - select MII - help - This option enables the ETRAX FS built-in 10/100Mbit Ethernet - controller. - -config ETRAX_NO_PHY - bool "PHY not present" - depends on ETRAX_ETHERNET - help - This option disables all MDIO communication with an ethernet - transceiver connected to the MII interface. This option shall - typically be enabled if the MII interface is connected to a - switch. This option should normally be disabled. If enabled, - speed and duplex will be locked to 100 Mbit and full duplex. - -config ETRAXFS_SERIAL - bool "Serial-port support" - depends on ETRAX_ARCH_V32 - select SERIAL_CORE - select SERIAL_CORE_CONSOLE - help - Enables the ETRAX FS serial driver for ser0 (ttyS0) - You probably want this enabled. - -config ETRAX_RS485 - bool "RS-485 support" - depends on ETRAXFS_SERIAL - help - Enables support for RS-485 serial communication. - -config ETRAX_RS485_DISABLE_RECEIVER - bool "Disable serial receiver" - depends on ETRAX_RS485 - help - It is necessary to disable the serial receiver to avoid serial - loopback. Not all products are able to do this in software only. - -config ETRAX_SERIAL_PORT0 - bool "Serial port 0 enabled" - depends on ETRAXFS_SERIAL - help - Enables the ETRAX FS serial driver for ser0 (ttyS0) - Normally you want this on. You can control what DMA channels to use - if you do not need DMA to something else. - ser0 can use dma4 or dma6 for output and dma5 or dma7 for input. - -config ETRAX_SERIAL_PORT1 - bool "Serial port 1 enabled" - depends on ETRAXFS_SERIAL - help - Enables the ETRAX FS serial driver for ser1 (ttyS1). - -config ETRAX_SERIAL_PORT2 - bool "Serial port 2 enabled" - depends on ETRAXFS_SERIAL - help - Enables the ETRAX FS serial driver for ser2 (ttyS2). - -config ETRAX_SERIAL_PORT3 - bool "Serial port 3 enabled" - depends on ETRAXFS_SERIAL - help - Enables the ETRAX FS serial driver for ser3 (ttyS3). - -config ETRAX_SYNCHRONOUS_SERIAL - bool "Synchronous serial-port support" - depends on ETRAX_ARCH_V32 - help - Enables the ETRAX FS synchronous serial driver. - -config ETRAX_SYNCHRONOUS_SERIAL_PORT0 - bool "Synchronous serial port 0 enabled" - depends on ETRAX_SYNCHRONOUS_SERIAL - help - Enabled synchronous serial port 0. - -config ETRAX_SYNCHRONOUS_SERIAL0_DMA - bool "Enable DMA on synchronous serial port 0." - depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0 - help - A synchronous serial port can run in manual or DMA mode. - Selecting this option will make it run in DMA mode. - -config ETRAX_SYNCHRONOUS_SERIAL_PORT1 - bool "Synchronous serial port 1 enabled" - depends on ETRAX_SYNCHRONOUS_SERIAL && ETRAXFS - help - Enabled synchronous serial port 1. - -config ETRAX_SYNCHRONOUS_SERIAL1_DMA - bool "Enable DMA on synchronous serial port 1." - depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1 - help - A synchronous serial port can run in manual or DMA mode. - Selecting this option will make it run in DMA mode. - -config ETRAX_AXISFLASHMAP - bool "Axis flash-map support" - depends on ETRAX_ARCH_V32 - select MTD - select MTD_CFI - select MTD_CFI_AMDSTD - select MTD_JEDECPROBE - select MTD_BLOCK - select MTD_COMPLEX_MAPPINGS - select MTD_MTDRAM - help - This option enables MTD mapping of flash devices. Needed to use - flash memories. If unsure, say Y. - -config ETRAX_AXISFLASHMAP_MTD0WHOLE - bool "MTD0 is whole boot flash device" - depends on ETRAX_AXISFLASHMAP - help - When this option is not set, mtd0 refers to the first partition - on the boot flash device. When set, mtd0 refers to the whole - device, with mtd1 referring to the first partition etc. - -config ETRAX_PTABLE_SECTOR - int "Byte-offset of partition table sector" - depends on ETRAX_AXISFLASHMAP - default "65536" - help - Byte-offset of the partition table in the first flash chip. - The default value is 64kB and should not be changed unless - you know exactly what you are doing. The only valid reason - for changing this is when the flash block size is bigger - than 64kB (e.g. when using two parallel 16 bit flashes). - -config ETRAX_NANDFLASH - bool "NAND flash support" - depends on ETRAX_ARCH_V32 - select MTD_NAND - help - This option enables MTD mapping of NAND flash devices. Needed to use - NAND flash memories. If unsure, say Y. - -config ETRAX_NANDBOOT - bool "Boot from NAND flash" - depends on ETRAX_NANDFLASH - help - This options enables booting from NAND flash devices. - Say Y if your boot code, kernel and root file system is in - NAND flash. Say N if they are in NOR flash. - -config ETRAX_CARDBUS - bool "Cardbus support" - depends on ETRAX_ARCH_V32 - help - Enabled the ETRAX Cardbus driver. - -config PCI - bool - depends on ETRAX_CARDBUS - default y - select HAVE_GENERIC_DMA_COHERENT - -config ETRAX_IOP_FW_LOAD - tristate "IO-processor hotplug firmware loading support" - depends on ETRAX_ARCH_V32 - select FW_LOADER - help - Enables IO-processor hotplug firmware loading support. - -config ETRAX_STREAMCOPROC - tristate "Stream co-processor driver enabled" - depends on ETRAX_ARCH_V32 - help - This option enables a driver for the stream co-processor - for cryptographic operations. - -config ETRAX_MMC_IOP - tristate "MMC/SD host driver using IO-processor" - depends on ETRAX_ARCH_V32 && MMC - help - This option enables the SD/MMC host controller interface. - The host controller is implemented using the built in - IO-Processor. Only the SPU is used in this implementation. - -config ETRAX_SPI_MMC -# Make this one of several "choices" (possible simultaneously but -# suggested uniquely) when an IOP driver emerges for "real" MMC/SD -# protocol support. - tristate - depends on !ETRAX_MMC_IOP - default MMC - select SPI - select MMC_SPI - -# While the board info is MMC_SPI only, the drivers are written to be -# independent of MMC_SPI, so we'll keep SPI non-dependent on the -# MMC_SPI config choices (well, except for a single depends-on-line -# for the board-info file until a separate non-MMC SPI board file -# emerges). -# FIXME: When that happens, we'll need to be able to ask for and -# configure non-MMC SPI ports together with MMC_SPI ports (if multiple -# SPI ports are enabled). - -config SPI_ETRAX_SSER - tristate - depends on SPI_MASTER && ETRAX_ARCH_V32 - select SPI_BITBANG - help - This enables using an synchronous serial (sser) port as a - SPI master controller on Axis ETRAX FS and later. The - driver can be configured to use any sser port. - -config SPI_ETRAX_GPIO - tristate - depends on SPI_MASTER && ETRAX_ARCH_V32 - select SPI_BITBANG - help - This enables using GPIO pins port as a SPI master controller - on Axis ETRAX FS and later. The driver can be configured to - use any GPIO pins. - -config ETRAX_SPI_SSER0 - tristate "SPI using synchronous serial port 0 (sser0)" - depends on ETRAX_SPI_MMC - default m if MMC_SPI=m - default y if MMC_SPI=y - default y if MMC_SPI=n - select SPI_ETRAX_SSER - help - Say Y for an MMC/SD socket connected to synchronous serial port 0, - or for devices using the SPI protocol on that port. Say m if you - want to build it as a module, which will be named spi_crisv32_sser. - (You need to select MMC separately.) - -config ETRAX_SPI_SSER1 - tristate "SPI using synchronous serial port 1 (sser1)" - depends on ETRAX_SPI_MMC - default m if MMC_SPI=m && ETRAX_SPI_SSER0=n - default y if MMC_SPI=y && ETRAX_SPI_SSER0=n - default y if MMC_SPI=n && ETRAX_SPI_SSER0=n - select SPI_ETRAX_SSER - help - Say Y for an MMC/SD socket connected to synchronous serial port 1, - or for devices using the SPI protocol on that port. Say m if you - want to build it as a module, which will be named spi_crisv32_sser. - (You need to select MMC separately.) - -config ETRAX_SPI_GPIO - tristate "Bitbanged SPI using gpio pins" - depends on ETRAX_SPI_MMC - select SPI_ETRAX_GPIO - default m if MMC_SPI=m && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n - default y if MMC_SPI=y && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n - default y if MMC_SPI=n && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n - help - Say Y for an MMC/SD socket connected to general I/O pins (but not - a complete synchronous serial ports), or for devices using the SPI - protocol on general I/O pins. Slow and slows down the system. - Say m to build it as a module, which will be called spi_crisv32_gpio. - (You need to select MMC separately.) - -endif |