diff options
Diffstat (limited to 'arch/blackfin/mach-bf527/include/mach/defBF522.h')
| -rw-r--r-- | arch/blackfin/mach-bf527/include/mach/defBF522.h | 71 |
1 files changed, 0 insertions, 71 deletions
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF522.h b/arch/blackfin/mach-bf527/include/mach/defBF522.h index 37d353a19722..e8fdacb8c64b 100644 --- a/arch/blackfin/mach-bf527/include/mach/defBF522.h +++ b/arch/blackfin/mach-bf527/include/mach/defBF522.h @@ -1084,77 +1084,6 @@ #define ERR_NCOR 0x8000 /* Error Not Corrected Indicator */ -/* ******************** TWO-WIRE INTERFACE (TWI) MASKS ***********************/ -/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y); ) */ -#define CLKLOW(x) ((x) & 0xFF) /* Periods Clock Is Held Low */ -#define CLKHI(y) (((y)&0xFF)<<0x8) /* Periods Before New Clock Low */ - -/* TWI_PRESCALE Masks */ -#define PRESCALE 0x007F /* SCLKs Per Internal Time Reference (10MHz) */ -#define TWI_ENA 0x0080 /* TWI Enable */ -#define SCCB 0x0200 /* SCCB Compatibility Enable */ - -/* TWI_SLAVE_CTL Masks */ -#define SEN 0x0001 /* Slave Enable */ -#define SADD_LEN 0x0002 /* Slave Address Length */ -#define STDVAL 0x0004 /* Slave Transmit Data Valid */ -#define NAK 0x0008 /* NAK/ACK* Generated At Conclusion Of Transfer */ -#define GEN 0x0010 /* General Call Adrress Matching Enabled */ - -/* TWI_SLAVE_STAT Masks */ -#define SDIR 0x0001 /* Slave Transfer Direction (Transmit/Receive*) */ -#define GCALL 0x0002 /* General Call Indicator */ - -/* TWI_MASTER_CTL Masks */ -#define MEN 0x0001 /* Master Mode Enable */ -#define MADD_LEN 0x0002 /* Master Address Length */ -#define MDIR 0x0004 /* Master Transmit Direction (RX/TX*) */ -#define FAST 0x0008 /* Use Fast Mode Timing Specs */ -#define STOP 0x0010 /* Issue Stop Condition */ -#define RSTART 0x0020 /* Repeat Start or Stop* At End Of Transfer */ -#define DCNT 0x3FC0 /* Data Bytes To Transfer */ -#define SDAOVR 0x4000 /* Serial Data Override */ -#define SCLOVR 0x8000 /* Serial Clock Override */ - -/* TWI_MASTER_STAT Masks */ -#define MPROG 0x0001 /* Master Transfer In Progress */ -#define LOSTARB 0x0002 /* Lost Arbitration Indicator (Xfer Aborted) */ -#define ANAK 0x0004 /* Address Not Acknowledged */ -#define DNAK 0x0008 /* Data Not Acknowledged */ -#define BUFRDERR 0x0010 /* Buffer Read Error */ -#define BUFWRERR 0x0020 /* Buffer Write Error */ -#define SDASEN 0x0040 /* Serial Data Sense */ -#define SCLSEN 0x0080 /* Serial Clock Sense */ -#define BUSBUSY 0x0100 /* Bus Busy Indicator */ - -/* TWI_INT_SRC and TWI_INT_ENABLE Masks */ -#define SINIT 0x0001 /* Slave Transfer Initiated */ -#define SCOMP 0x0002 /* Slave Transfer Complete */ -#define SERR 0x0004 /* Slave Transfer Error */ -#define SOVF 0x0008 /* Slave Overflow */ -#define MCOMP 0x0010 /* Master Transfer Complete */ -#define MERR 0x0020 /* Master Transfer Error */ -#define XMTSERV 0x0040 /* Transmit FIFO Service */ -#define RCVSERV 0x0080 /* Receive FIFO Service */ - -/* TWI_FIFO_CTRL Masks */ -#define XMTFLUSH 0x0001 /* Transmit Buffer Flush */ -#define RCVFLUSH 0x0002 /* Receive Buffer Flush */ -#define XMTINTLEN 0x0004 /* Transmit Buffer Interrupt Length */ -#define RCVINTLEN 0x0008 /* Receive Buffer Interrupt Length */ - -/* TWI_FIFO_STAT Masks */ -#define XMTSTAT 0x0003 /* Transmit FIFO Status */ -#define XMT_EMPTY 0x0000 /* Transmit FIFO Empty */ -#define XMT_HALF 0x0001 /* Transmit FIFO Has 1 Byte To Write */ -#define XMT_FULL 0x0003 /* Transmit FIFO Full (2 Bytes To Write) */ - -#define RCVSTAT 0x000C /* Receive FIFO Status */ -#define RCV_EMPTY 0x0000 /* Receive FIFO Empty */ -#define RCV_HALF 0x0004 /* Receive FIFO Has 1 Byte To Read */ -#define RCV_FULL 0x000C /* Receive FIFO Full (2 Bytes To Read) */ - - /* Omit CAN masks from defBF534.h */ /* ******************* PIN CONTROL REGISTER MASKS ************************/ |