diff options
Diffstat (limited to 'arch/arm/mach-mx3/mach-mx31_3ds.c')
| -rw-r--r-- | arch/arm/mach-mx3/mach-mx31_3ds.c | 266 |
1 files changed, 266 insertions, 0 deletions
diff --git a/arch/arm/mach-mx3/mach-mx31_3ds.c b/arch/arm/mach-mx3/mach-mx31_3ds.c new file mode 100644 index 000000000000..b88c18ad7698 --- /dev/null +++ b/arch/arm/mach-mx3/mach-mx31_3ds.c @@ -0,0 +1,266 @@ +/* + * Copyright 2008 Freescale Semiconductor, Inc. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/types.h> +#include <linux/init.h> +#include <linux/clk.h> +#include <linux/irq.h> +#include <linux/gpio.h> +#include <linux/smsc911x.h> +#include <linux/platform_device.h> + +#include <mach/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/time.h> +#include <asm/memory.h> +#include <asm/mach/map.h> +#include <mach/common.h> +#include <mach/board-mx31pdk.h> +#include <mach/imx-uart.h> +#include <mach/iomux-mx3.h> +#include "devices.h" + +/*! + * @file mx31pdk.c + * + * @brief This file contains the board-specific initialization routines. + * + * @ingroup System + */ + +static int mx31pdk_pins[] = { + /* UART1 */ + MX31_PIN_CTS1__CTS1, + MX31_PIN_RTS1__RTS1, + MX31_PIN_TXD1__TXD1, + MX31_PIN_RXD1__RXD1, + IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO), +}; + +static struct imxuart_platform_data uart_pdata = { + .flags = IMXUART_HAVE_RTSCTS, +}; + +/* + * Support for the SMSC9217 on the Debug board. + */ + +static struct smsc911x_platform_config smsc911x_config = { + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL, + .flags = SMSC911X_USE_16BIT | SMSC911X_FORCE_INTERNAL_PHY, + .phy_interface = PHY_INTERFACE_MODE_MII, +}; + +static struct resource smsc911x_resources[] = { + { + .start = LAN9217_BASE_ADDR, + .end = LAN9217_BASE_ADDR + 0xff, + .flags = IORESOURCE_MEM, + }, { + .start = EXPIO_INT_ENET, + .end = EXPIO_INT_ENET, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device smsc911x_device = { + .name = "smsc911x", + .id = -1, + .num_resources = ARRAY_SIZE(smsc911x_resources), + .resource = smsc911x_resources, + .dev = { + .platform_data = &smsc911x_config, + }, +}; + +/* + * Routines for the CPLD on the debug board. It contains a CPLD handling + * LEDs, switches, interrupts for Ethernet. + */ + +static void mx31pdk_expio_irq_handler(uint32_t irq, struct irq_desc *desc) +{ + uint32_t imr_val; + uint32_t int_valid; + uint32_t expio_irq; + + imr_val = __raw_readw(CPLD_INT_MASK_REG); + int_valid = __raw_readw(CPLD_INT_STATUS_REG) & ~imr_val; + + expio_irq = MXC_EXP_IO_BASE; + for (; int_valid != 0; int_valid >>= 1, expio_irq++) { + if ((int_valid & 1) == 0) + continue; + generic_handle_irq(expio_irq); + } +} + +/* + * Disable an expio pin's interrupt by setting the bit in the imr. + * @param irq an expio virtual irq number + */ +static void expio_mask_irq(uint32_t irq) +{ + uint16_t reg; + uint32_t expio = MXC_IRQ_TO_EXPIO(irq); + + /* mask the interrupt */ + reg = __raw_readw(CPLD_INT_MASK_REG); + reg |= 1 << expio; + __raw_writew(reg, CPLD_INT_MASK_REG); +} + +/* + * Acknowledge an expanded io pin's interrupt by clearing the bit in the isr. + * @param irq an expanded io virtual irq number + */ +static void expio_ack_irq(uint32_t irq) +{ + uint32_t expio = MXC_IRQ_TO_EXPIO(irq); + + /* clear the interrupt status */ + __raw_writew(1 << expio, CPLD_INT_RESET_REG); + __raw_writew(0, CPLD_INT_RESET_REG); + /* mask the interrupt */ + expio_mask_irq(irq); +} + +/* + * Enable a expio pin's interrupt by clearing the bit in the imr. + * @param irq a expio virtual irq number + */ +static void expio_unmask_irq(uint32_t irq) +{ + uint16_t reg; + uint32_t expio = MXC_IRQ_TO_EXPIO(irq); + + /* unmask the interrupt */ + reg = __raw_readw(CPLD_INT_MASK_REG); + reg &= ~(1 << expio); + __raw_writew(reg, CPLD_INT_MASK_REG); +} + +static struct irq_chip expio_irq_chip = { + .ack = expio_ack_irq, + .mask = expio_mask_irq, + .unmask = expio_unmask_irq, +}; + +static int __init mx31pdk_init_expio(void) +{ + int i; + int ret; + + /* Check if there's a debug board connected */ + if ((__raw_readw(CPLD_MAGIC_NUMBER1_REG) != 0xAAAA) || + (__raw_readw(CPLD_MAGIC_NUMBER2_REG) != 0x5555) || + (__raw_readw(CPLD_MAGIC_NUMBER3_REG) != 0xCAFE)) { + /* No Debug board found */ + return -ENODEV; + } + + pr_info("i.MX31PDK Debug board detected, rev = 0x%04X\n", + __raw_readw(CPLD_CODE_VER_REG)); + + /* + * Configure INT line as GPIO input + */ + ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1), "sms9217-irq"); + if (ret) + pr_warning("could not get LAN irq gpio\n"); + else + gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO1_1)); + + /* Disable the interrupts and clear the status */ + __raw_writew(0, CPLD_INT_MASK_REG); + __raw_writew(0xFFFF, CPLD_INT_RESET_REG); + __raw_writew(0, CPLD_INT_RESET_REG); + __raw_writew(0x1F, CPLD_INT_MASK_REG); + for (i = MXC_EXP_IO_BASE; + i < (MXC_EXP_IO_BASE + MXC_MAX_EXP_IO_LINES); + i++) { + set_irq_chip(i, &expio_irq_chip); + set_irq_handler(i, handle_level_irq); + set_irq_flags(i, IRQF_VALID); + } + set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW); + set_irq_chained_handler(EXPIO_PARENT_INT, mx31pdk_expio_irq_handler); + + return 0; +} + +/* + * This structure defines the MX31 memory map. + */ +static struct map_desc mx31pdk_io_desc[] __initdata = { + { + .virtual = MX31_CS5_BASE_ADDR_VIRT, + .pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR), + .length = MX31_CS5_SIZE, + .type = MT_DEVICE, + }, +}; + +/* + * Set up static virtual mappings. + */ +static void __init mx31pdk_map_io(void) +{ + mx31_map_io(); + iotable_init(mx31pdk_io_desc, ARRAY_SIZE(mx31pdk_io_desc)); +} + +/*! + * Board specific initialization. + */ +static void __init mxc_board_init(void) +{ + mxc_iomux_setup_multiple_pins(mx31pdk_pins, ARRAY_SIZE(mx31pdk_pins), + "mx31pdk"); + + mxc_register_device(&mxc_uart_device0, &uart_pdata); + + if (!mx31pdk_init_expio()) + platform_device_register(&smsc911x_device); +} + +static void __init mx31pdk_timer_init(void) +{ + mx31_clocks_init(26000000); +} + +static struct sys_timer mx31pdk_timer = { + .init = mx31pdk_timer_init, +}; + +/* + * The following uses standard kernel macros defined in arch.h in order to + * initialize __mach_desc_MX31PDK data structure. + */ +MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)") + /* Maintainer: Freescale Semiconductor, Inc. */ + .phys_io = MX31_AIPS1_BASE_ADDR, + .io_pg_offst = (MX31_AIPS1_BASE_ADDR_VIRT >> 18) & 0xfffc, + .boot_params = MX3x_PHYS_OFFSET + 0x100, + .map_io = mx31pdk_map_io, + .init_irq = mx31_init_irq, + .init_machine = mxc_board_init, + .timer = &mx31pdk_timer, +MACHINE_END |