diff options
Diffstat (limited to 'arch/arm/mach-davinci/board-da830-evm.c')
| -rw-r--r-- | arch/arm/mach-davinci/board-da830-evm.c | 125 |
1 files changed, 125 insertions, 0 deletions
diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index 20100370e2e6..9dc4813c8645 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -13,6 +13,7 @@ #include <linux/module.h> #include <linux/init.h> #include <linux/console.h> +#include <linux/interrupt.h> #include <linux/gpio.h> #include <linux/i2c.h> #include <linux/i2c/pcf857x.h> @@ -28,6 +29,7 @@ #include <mach/gpio.h> #include <mach/da8xx.h> #include <mach/asp.h> +#include <mach/usb.h> #define DA830_EVM_PHY_MASK 0x0 #define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ @@ -84,6 +86,127 @@ static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = { .bus_delay = 0, /* usec */ }; +/* + * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4]. + */ +#define ON_BD_USB_DRV GPIO_TO_PIN(1, 15) +#define ON_BD_USB_OVC GPIO_TO_PIN(2, 4) + +static const short da830_evm_usb11_pins[] = { + DA830_GPIO1_15, DA830_GPIO2_4, + -1 +}; + +static da8xx_ocic_handler_t da830_evm_usb_ocic_handler; + +static int da830_evm_usb_set_power(unsigned port, int on) +{ + gpio_set_value(ON_BD_USB_DRV, on); + return 0; +} + +static int da830_evm_usb_get_power(unsigned port) +{ + return gpio_get_value(ON_BD_USB_DRV); +} + +static int da830_evm_usb_get_oci(unsigned port) +{ + return !gpio_get_value(ON_BD_USB_OVC); +} + +static irqreturn_t da830_evm_usb_ocic_irq(int, void *); + +static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler) +{ + int irq = gpio_to_irq(ON_BD_USB_OVC); + int error = 0; + + if (handler != NULL) { + da830_evm_usb_ocic_handler = handler; + + error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED | + IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, + "OHCI over-current indicator", NULL); + if (error) + printk(KERN_ERR "%s: could not request IRQ to watch " + "over-current indicator changes\n", __func__); + } else + free_irq(irq, NULL); + + return error; +} + +static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = { + .set_power = da830_evm_usb_set_power, + .get_power = da830_evm_usb_get_power, + .get_oci = da830_evm_usb_get_oci, + .ocic_notify = da830_evm_usb_ocic_notify, + + /* TPS2065 switch @ 5V */ + .potpgt = (3 + 1) / 2, /* 3 ms max */ +}; + +static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id) +{ + da830_evm_usb_ocic_handler(&da830_evm_usb11_pdata, 1); + return IRQ_HANDLED; +} + +static __init void da830_evm_usb_init(void) +{ + u32 cfgchip2; + int ret; + + /* + * Set up USB clock/mode in the CFGCHIP2 register. + * FYI: CFGCHIP2 is 0x0000ef00 initially. + */ + cfgchip2 = __raw_readl(DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG)); + + /* USB2.0 PHY reference clock is 24 MHz */ + cfgchip2 &= ~CFGCHIP2_REFFREQ; + cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ; + + /* + * Select internal reference clock for USB 2.0 PHY + * and use it as a clock source for USB 1.1 PHY + * (this is the default setting anyway). + */ + cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX; + cfgchip2 |= CFGCHIP2_USB2PHYCLKMUX; + + __raw_writel(cfgchip2, DA8XX_SYSCFG_VIRT(DA8XX_CFGCHIP2_REG)); + + ret = da8xx_pinmux_setup(da830_evm_usb11_pins); + if (ret) { + pr_warning("%s: USB 1.1 PinMux setup failed: %d\n", + __func__, ret); + return; + } + + ret = gpio_request(ON_BD_USB_DRV, "ON_BD_USB_DRV"); + if (ret) { + printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port " + "power control: %d\n", __func__, ret); + return; + } + gpio_direction_output(ON_BD_USB_DRV, 0); + + ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC"); + if (ret) { + printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port " + "over-current indicator: %d\n", __func__, ret); + return; + } + gpio_direction_input(ON_BD_USB_OVC); + + ret = da8xx_register_usb11(&da830_evm_usb11_pdata); + if (ret) + pr_warning("%s: USB 1.1 registration failed: %d\n", + __func__, ret); +} + static struct davinci_uart_config da830_evm_uart_config __initdata = { .enabled_uarts = 0x7, }; @@ -186,6 +309,8 @@ static __init void da830_evm_init(void) pr_warning("da830_evm_init: i2c0 registration failed: %d\n", ret); + da830_evm_usb_init(); + soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK; soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY; soc_info->emac_pdata->rmii_en = 1; |