1 files changed, 0 insertions, 333 deletions
diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c
deleted file mode 100644
index 8bca329b0293..000000000000
--- a/arch/arm/mach-at91/board-sam9rlek.c
+++ /dev/null
@@ -1,333 +0,0 @@
-/*
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2007 Atmel Corporation
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License.  See the file COPYING in the main directory of this archive for
- * more details.
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/fb.h>
-#include <linux/clk.h>
-#include <linux/input.h>
-#include <linux/gpio_keys.h>
-#include <linux/platform_data/at91_adc.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
-	/* Initialize processor: 12.000 MHz crystal */
-	at91_initialize(12000000);
-}
-
-/*
- * USB HS Device port
- */
-static struct usba_platform_data __initdata ek_usba_udc_data = {
-	.vbus_pin	= AT91_PIN_PA8,
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata mci0_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PA15,
-		.wp_pin		= -EINVAL,
-	},
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name	= "Partition 1",
-		.offset	= 0,
-		.size	= SZ_256K,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.det_pin	= -EINVAL,
-	.rdy_pin	= AT91_PIN_PD17,
-	.enable_pin	= AT91_PIN_PB6,
-	.ecc_mode	= NAND_ECC_SOFT,
-	.on_flash_bbt	= 1,
-	.parts		= ek_nand_partition,
-	.num_parts	= ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 1,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 1,
-
-	.ncs_read_pulse		= 3,
-	.nrd_pulse		= 3,
-	.ncs_write_pulse	= 3,
-	.nwe_pulse		= 3,
-
-	.read_cycle		= 5,
-	.write_cycle		= 5,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
-	.tdf_cycles		= 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * SPI devices
- */
-static struct spi_board_info ek_spi_devices[] = {
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-};
-
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
-	{
-		.name		= "TX09D50VM1CCA @ 60",
-		.refresh	= 60,
-		.xres		= 240,		.yres		= 320,
-		.pixclock	= KHZ2PICOS(4965),
-
-		.left_margin	= 1,		.right_margin	= 33,
-		.upper_margin	= 1,		.lower_margin	= 0,
-		.hsync_len	= 5,		.vsync_len	= 1,
-
-		.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
-		.vmode		= FB_VMODE_NONINTERLACED,
-	},
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
-	.manufacturer	= "HIT",
-	.monitor	= "TX09D50VM1CCA",
-
-	.modedb		= at91_tft_vga_modes,
-	.modedb_len	= ARRAY_SIZE(at91_tft_vga_modes),
-	.hfmin		= 15000,
-	.hfmax		= 64000,
-	.vfmin		= 50,
-	.vfmax		= 150,
-};
-
-#define AT91SAM9RL_DEFAULT_LCDCON2	(ATMEL_LCDC_MEMOR_LITTLE \
-					| ATMEL_LCDC_DISTYPE_TFT \
-					| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
-{
-	if (on)
-		at91_set_gpio_value(AT91_PIN_PC1, 0);	/* power up */
-	else
-		at91_set_gpio_value(AT91_PIN_PC1, 1);	/* power down */
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
-	.lcdcon_is_backlight            = true,
-	.default_bpp			= 16,
-	.default_dmacon			= ATMEL_LCDC_DMAEN,
-	.default_lcdcon2		= AT91SAM9RL_DEFAULT_LCDCON2,
-	.default_monspecs		= &at91fb_default_monspecs,
-	.atmel_lcdfb_power_control	= at91_lcdc_power_control,
-	.guard_time			= 1,
-	.lcd_wiring_mode		= ATMEL_LCDC_WIRING_RGB,
-};
-
-#else
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
-#endif
-
-
-/*
- * AC97
- * reset_pin is not connected: NRST
- */
-static struct ac97c_platform_data ek_ac97_data = {
-	.reset_pin	= -EINVAL,
-};
-
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PD15,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "bottom" led, green, userled2 to be defined */
-		.name			= "ds2",
-		.gpio			= AT91_PIN_PD16,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds3",
-		.gpio			= AT91_PIN_PD14,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-
-/*
- * ADC + Touchscreen
- */
-static struct at91_adc_data ek_adc_data = {
-	.channels_used = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5),
-	.use_external_triggers = true,
-	.vref = 3300,
-	.touchscreen_type = ATMEL_ADC_TOUCHSCREEN_4WIRE,
-};
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
-	{
-		.gpio		= AT91_PIN_PB0,
-		.code		= BTN_2,
-		.desc		= "Right Click",
-		.active_low	= 1,
-		.wakeup		= 1,
-	},
-	{
-		.gpio		= AT91_PIN_PB1,
-		.code		= BTN_1,
-		.desc		= "Left Click",
-		.active_low	= 1,
-		.wakeup		= 1,
-	}
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
-	.buttons	= ek_buttons,
-	.nbuttons	= ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_button_data,
-	}
-};
-
-static void __init ek_add_device_buttons(void)
-{
-	at91_set_gpio_input(AT91_PIN_PB1, 1);	/* btn1 */
-	at91_set_deglitch(AT91_PIN_PB1, 1);
-	at91_set_gpio_input(AT91_PIN_PB0, 1);	/* btn2 */
-	at91_set_deglitch(AT91_PIN_PB0, 1);
-
-	platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-static void __init ek_board_init(void)
-{
-	at91_register_devices();
-
-	/* Serial */
-	/* DBGU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
-	at91_register_uart(AT91SAM9RL_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
-	at91_add_device_serial();
-	/* USB HS */
-	at91_add_device_usba(&ek_usba_udc_data);
-	/* I2C */
-	at91_add_device_i2c(NULL, 0);
-	/* NAND */
-	ek_add_device_nand();
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* MMC */
-	at91_add_device_mci(0, &mci0_data);
-	/* LCD Controller */
-	at91_add_device_lcdc(&ek_lcdc_data);
-	/* AC97 */
-	at91_add_device_ac97(&ek_ac97_data);
-	/* Touch Screen Controller + ADC */
-	at91_add_device_adc(&ek_adc_data);
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* Push Buttons */
-	ek_add_device_buttons();
-}
-
-MACHINE_START(AT91SAM9RLEK, "Atmel AT91SAM9RL-EK")
-	/* Maintainer: Atmel */
-	.init_time	= at91_init_time,
-	.map_io		= at91_map_io,
-	.handle_irq	= at91_aic_handle_irq,
-	.init_early	= ek_init_early,
-	.init_irq	= at91_init_irq_default,
-	.init_machine	= ek_board_init,
-MACHINE_END