diff options
Diffstat (limited to 'arch/arm/boot/dts')
-rw-r--r--[-rwxr-xr-x] | arch/arm/boot/dts/am335x-osd3358-sm-red.dts | 0 | ||||
-rw-r--r-- | arch/arm/boot/dts/am4372.dtsi | 1 | ||||
-rw-r--r-- | arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 2 | ||||
-rw-r--r-- | arch/arm/boot/dts/bcm63138.dtsi | 14 | ||||
-rw-r--r-- | arch/arm/boot/dts/imx23-evk.dts | 90 | ||||
-rw-r--r-- | arch/arm/boot/dts/imx28-evk.dts | 183 | ||||
-rw-r--r-- | arch/arm/boot/dts/imx53-qsb-common.dtsi | 11 | ||||
-rw-r--r-- | arch/arm/boot/dts/imx7d.dtsi | 17 | ||||
-rw-r--r-- | arch/arm/boot/dts/omap4-droid4-xt894.dts | 20 | ||||
-rw-r--r-- | arch/arm/boot/dts/sama5d3_emac.dtsi | 2 | ||||
-rw-r--r-- | arch/arm/boot/dts/stm32mp157c.dtsi | 4 | ||||
-rw-r--r-- | arch/arm/boot/dts/sun8i-r40.dtsi | 3 |
12 files changed, 173 insertions, 174 deletions
diff --git a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts index 4d969013f99a..4d969013f99a 100755..100644 --- a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts +++ b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index f0cbd86312dc..d4b7c59eec68 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -469,6 +469,7 @@ ti,hwmods = "rtc"; clocks = <&clk_32768_ck>; clock-names = "int-clk"; + system-power-controller; status = "disabled"; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts index b10dccd0958f..3b1baa8605a7 100644 --- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts @@ -11,6 +11,7 @@ #include "sama5d2-pinfunc.h" #include <dt-bindings/mfd/atmel-flexcom.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/at91.h> / { model = "Atmel SAMA5D2 PTC EK"; @@ -299,6 +300,7 @@ <PIN_PA30__NWE_NANDWE>, <PIN_PB2__NRD_NANDOE>; bias-pull-up; + atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>; }; ale_cle_rdy_cs { diff --git a/arch/arm/boot/dts/bcm63138.dtsi b/arch/arm/boot/dts/bcm63138.dtsi index 43ee992ccdcf..6df61518776f 100644 --- a/arch/arm/boot/dts/bcm63138.dtsi +++ b/arch/arm/boot/dts/bcm63138.dtsi @@ -106,21 +106,23 @@ global_timer: timer@1e200 { compatible = "arm,cortex-a9-global-timer"; reg = <0x1e200 0x20>; - interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>; clocks = <&axi_clk>; }; local_timer: local-timer@1e600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x1e600 0x20>; - interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_EDGE_RISING)>; clocks = <&axi_clk>; }; twd_watchdog: watchdog@1e620 { compatible = "arm,cortex-a9-twd-wdt"; reg = <0x1e620 0x20>; - interrupts = <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_LEVEL_HIGH)>; }; armpll: armpll { @@ -158,7 +160,7 @@ serial0: serial@600 { compatible = "brcm,bcm6345-uart"; reg = <0x600 0x1b>; - interrupts = <GIC_SPI 32 0>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; clocks = <&periph_clk>; clock-names = "periph"; status = "disabled"; @@ -167,7 +169,7 @@ serial1: serial@620 { compatible = "brcm,bcm6345-uart"; reg = <0x620 0x1b>; - interrupts = <GIC_SPI 33 0>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; clocks = <&periph_clk>; clock-names = "periph"; status = "disabled"; @@ -180,7 +182,7 @@ reg = <0x2000 0x600>, <0xf0 0x10>; reg-names = "nand", "nand-int-base"; status = "disabled"; - interrupts = <GIC_SPI 38 0>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "nand"; }; diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts index 9fb47724b9c1..ad2ae25b7b4d 100644 --- a/arch/arm/boot/dts/imx23-evk.dts +++ b/arch/arm/boot/dts/imx23-evk.dts @@ -13,6 +13,43 @@ reg = <0x40000000 0x08000000>; }; + reg_vddio_sd0: regulator-vddio-sd0 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 29 0>; + }; + + reg_lcd_3v3: regulator-lcd-3v3 { + compatible = "regulator-fixed"; + regulator-name = "lcd-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 18 0>; + enable-active-high; + }; + + reg_lcd_5v: regulator-lcd-5v { + compatible = "regulator-fixed"; + regulator-name = "lcd-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + panel { + compatible = "sii,43wvf1g"; + backlight = <&backlight_display>; + dvdd-supply = <®_lcd_3v3>; + avdd-supply = <®_lcd_5v>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + apb@80000000 { apbh@80000000 { gpmi-nand@8000c000 { @@ -52,31 +89,11 @@ lcdif@80030000 { pinctrl-names = "default"; pinctrl-0 = <&lcdif_24bit_pins_a>; - lcd-supply = <®_lcd_3v3>; - display = <&display0>; status = "okay"; - display0: display0 { - bits-per-pixel = <32>; - bus-width = <24>; - - display-timings { - native-mode = <&timing0>; - timing0: timing0 { - clock-frequency = <9200000>; - hactive = <480>; - vactive = <272>; - hback-porch = <15>; - hfront-porch = <8>; - vback-porch = <12>; - vfront-porch = <4>; - hsync-len = <1>; - vsync-len = <1>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <0>; - }; + port { + display_out: endpoint { + remote-endpoint = <&panel_in>; }; }; }; @@ -118,32 +135,7 @@ }; }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - reg_vddio_sd0: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "vddio-sd0"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio1 29 0>; - }; - - reg_lcd_3v3: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "lcd-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio1 18 0>; - enable-active-high; - }; - }; - - backlight { + backlight_display: backlight { compatible = "pwm-backlight"; pwms = <&pwm 2 5000000>; brightness-levels = <0 4 8 16 32 64 128 255>; diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index 6b0ae667640f..93ab5bdfe068 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -13,6 +13,87 @@ reg = <0x40000000 0x08000000>; }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vddio_sd0: regulator-vddio-sd0 { + compatible = "regulator-fixed"; + regulator-name = "vddio-sd0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 28 0>; + }; + + reg_fec_3v3: regulator-fec-3v3 { + compatible = "regulator-fixed"; + regulator-name = "fec-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 15 0>; + }; + + reg_usb0_vbus: regulator-usb0-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 9 0>; + enable-active-high; + }; + + reg_usb1_vbus: regulator-usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 8 0>; + enable-active-high; + }; + + reg_lcd_3v3: regulator-lcd-3v3 { + compatible = "regulator-fixed"; + regulator-name = "lcd-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 30 0>; + enable-active-high; + }; + + reg_can_3v3: regulator-can-3v3 { + compatible = "regulator-fixed"; + regulator-name = "can-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 13 0>; + enable-active-high; + }; + + reg_lcd_5v: regulator-lcd-5v { + compatible = "regulator-fixed"; + regulator-name = "lcd-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + panel { + compatible = "sii,43wvf1g"; + backlight = <&backlight_display>; + dvdd-supply = <®_lcd_3v3>; + avdd-supply = <®_lcd_5v>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + apb@80000000 { apbh@80000000 { gpmi-nand@8000c000 { @@ -116,31 +197,11 @@ pinctrl-names = "default"; pinctrl-0 = <&lcdif_24bit_pins_a &lcdif_pins_evk>; - lcd-supply = <®_lcd_3v3>; - display = <&display0>; status = "okay"; - display0: display0 { - bits-per-pixel = <32>; - bus-width = <24>; - - display-timings { - native-mode = <&timing0>; - timing0: timing0 { - clock-frequency = <33500000>; - hactive = <800>; - vactive = <480>; - hback-porch = <89>; - hfront-porch = <164>; - vback-porch = <23>; - vfront-porch = <10>; - hsync-len = <10>; - vsync-len = <10>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <0>; - }; + port { + display_out: endpoint { + remote-endpoint = <&panel_in>; }; }; }; @@ -269,80 +330,6 @@ }; }; - regulators { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <0>; - - reg_3p3v: regulator@0 { - compatible = "regulator-fixed"; - reg = <0>; - regulator-name = "3P3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - reg_vddio_sd0: regulator@1 { - compatible = "regulator-fixed"; - reg = <1>; - regulator-name = "vddio-sd0"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 28 0>; - }; - - reg_fec_3v3: regulator@2 { - compatible = "regulator-fixed"; - reg = <2>; - regulator-name = "fec-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio2 15 0>; - }; - - reg_usb0_vbus: regulator@3 { - compatible = "regulator-fixed"; - reg = <3>; - regulator-name = "usb0_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio3 9 0>; - enable-active-high; - }; - - reg_usb1_vbus: regulator@4 { - compatible = "regulator-fixed"; - reg = <4>; - regulator-name = "usb1_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio3 8 0>; - enable-active-high; - }; - - reg_lcd_3v3: regulator@5 { - compatible = "regulator-fixed"; - reg = <5>; - regulator-name = "lcd-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio3 30 0>; - enable-active-high; - }; - - reg_can_3v3: regulator@6 { - compatible = "regulator-fixed"; - reg = <6>; - regulator-name = "can-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio2 13 0>; - enable-active-high; - }; - - }; - sound { compatible = "fsl,imx28-evk-sgtl5000", "fsl,mxs-audio-sgtl5000"; @@ -363,7 +350,7 @@ }; }; - backlight { + backlight_display: backlight { compatible = "pwm-backlight"; pwms = <&pwm 2 5000000>; brightness-levels = <0 4 8 16 32 64 128 255>; diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/imx53-qsb-common.dtsi index 7423d462d1e4..50dde84b72ed 100644 --- a/arch/arm/boot/dts/imx53-qsb-common.dtsi +++ b/arch/arm/boot/dts/imx53-qsb-common.dtsi @@ -123,6 +123,17 @@ }; }; +&cpu0 { + /* CPU rated to 1GHz, not 1.2GHz as per the default settings */ + operating-points = < + /* kHz uV */ + 166666 850000 + 400000 900000 + 800000 1050000 + 1000000 1200000 + >; +}; + &esdhc1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_esdhc1>; diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi index 7cbc2ffa4b3a..efbdeaaa8dcd 100644 --- a/arch/arm/boot/dts/imx7d.dtsi +++ b/arch/arm/boot/dts/imx7d.dtsi @@ -126,10 +126,14 @@ interrupt-names = "msi"; #interrupt-cells = <1>; interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, - <0 0 0 2 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, - <0 0 0 3 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, - <0 0 0 4 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; + /* + * Reference manual lists pci irqs incorrectly + * Real hardware ordering is same as imx6: D+MSI, C, B, A + */ + interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>, <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>, <&clks IMX7D_PCIE_PHY_ROOT_CLK>; @@ -142,8 +146,9 @@ fsl,max-link-speed = <2>; power-domains = <&pgc_pcie_phy>; resets = <&src IMX7_RESET_PCIEPHY>, - <&src IMX7_RESET_PCIE_CTRL_APPS_EN>; - reset-names = "pciephy", "apps"; + <&src IMX7_RESET_PCIE_CTRL_APPS_EN>, + <&src IMX7_RESET_PCIE_CTRL_APPS_TURNOFF>; + reset-names = "pciephy", "apps", "turnoff"; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts index 12d6822f0057..04758a2a87f0 100644 --- a/arch/arm/boot/dts/omap4-droid4-xt894.dts +++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts @@ -354,7 +354,7 @@ &mmc2 { vmmc-supply = <&vsdio>; bus-width = <8>; - non-removable; + ti,non-removable; }; &mmc3 { @@ -621,15 +621,6 @@ OMAP4_IOPAD(0x10c, PIN_INPUT | MUX_MODE1) /* abe_mcbsp3_fsx */ >; }; -}; - -&omap4_pmx_wkup { - usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins { - /* gpio_wk0 */ - pinctrl-single,pins = < - OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3) - >; - }; vibrator_direction_pin: pinmux_vibrator_direction_pin { pinctrl-single,pins = < @@ -644,6 +635,15 @@ }; }; +&omap4_pmx_wkup { + usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins { + /* gpio_wk0 */ + pinctrl-single,pins = < + OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3) + >; + }; +}; + /* * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for * uart1 wakeirq. diff --git a/arch/arm/boot/dts/sama5d3_emac.dtsi b/arch/arm/boot/dts/sama5d3_emac.dtsi index 7cb235ef0fb6..6e9e1c2f9def 100644 --- a/arch/arm/boot/dts/sama5d3_emac.dtsi +++ b/arch/arm/boot/dts/sama5d3_emac.dtsi @@ -41,7 +41,7 @@ }; macb1: ethernet@f802c000 { - compatible = "cdns,at91sam9260-macb", "cdns,macb"; + compatible = "atmel,sama5d3-macb", "cdns,at91sam9260-macb", "cdns,macb"; reg = <0xf802c000 0x100>; interrupts = <35 IRQ_TYPE_LEVEL_HIGH 3>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi index 661be948ab74..185541a5b69f 100644 --- a/arch/arm/boot/dts/stm32mp157c.dtsi +++ b/arch/arm/boot/dts/stm32mp157c.dtsi @@ -1078,8 +1078,8 @@ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; clocks = <&rcc SPI6_K>; resets = <&rcc SPI6_R>; - dmas = <&mdma1 34 0x0 0x40008 0x0 0x0 0>, - <&mdma1 35 0x0 0x40002 0x0 0x0 0>; + dmas = <&mdma1 34 0x0 0x40008 0x0 0x0>, + <&mdma1 35 0x0 0x40002 0x0 0x0>; dma-names = "rx", "tx"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index ffd9f00f74a4..5f547c161baf 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -800,8 +800,7 @@ }; hdmi_phy: hdmi-phy@1ef0000 { - compatible = "allwinner,sun8i-r40-hdmi-phy", - "allwinner,sun50i-a64-hdmi-phy"; + compatible = "allwinner,sun8i-r40-hdmi-phy"; reg = <0x01ef0000 0x10000>; clocks = <&ccu CLK_BUS_HDMI1>, <&ccu CLK_HDMI_SLOW>, <&ccu 7>, <&ccu 16>; |