diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/rk808.txt | 8 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt | 60 |
2 files changed, 63 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 9e6e2592e5c8..4ca6aab4273a 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -24,6 +24,10 @@ Optional properties: - vcc10-supply: The input supply for LDO_REG6 - vcc11-supply: The input supply for LDO_REG8 - vcc12-supply: The input supply for SWITCH_REG2 +- dvs-gpios: buck1/2 can be controlled by gpio dvs, this is GPIO specifiers + for 2 host gpio's used for dvs. The format of the gpio specifier depends in + the gpio controller. If DVS GPIOs aren't present, voltage changes will happen + very quickly with no slow ramp time. Regulators: All the regulators of RK808 to be instantiated shall be listed in a child node named 'regulators'. Each regulator is represented @@ -55,7 +59,9 @@ Example: interrupt-parent = <&gpio0>; interrupts = <4 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&pmic_int>; + pinctrl-0 = <&pmic_int &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; reg = <0x1b>; rockchip,system-power-controller; wakeup-source; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 75b4604bad07..d00bfd8624a5 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -91,13 +91,65 @@ see regulator.txt - with additional custom properties described below: - regulator-initial-mode: Usage: optional Value type: <u32> - Descrption: 1 = Set initial mode to high power mode (HPM), also referred - to as NPM. HPM consumes more ground current than LPM, but + Description: 2 = Set initial mode to auto mode (automatically select + between HPM and LPM); not available on boost type + regulators. + + 1 = Set initial mode to high power mode (HPM), also referred + to as NPM. HPM consumes more ground current than LPM, but it can source significantly higher load current. HPM is not available on boost type regulators. For voltage switch type regulators, HPM implies that over current protection and - soft start are active all the time. 0 = Set initial mode to - low power mode (LPM). + soft start are active all the time. + + 0 = Set initial mode to low power mode (LPM). + +- qcom,ocp-max-retries: + Usage: optional + Value type: <u32> + Description: Maximum number of times to try toggling a voltage switch + off and back on as a result of consecutive over current + events. + +- qcom,ocp-retry-delay: + Usage: optional + Value type: <u32> + Description: Time to delay in milliseconds between each voltage switch + toggle after an over current event takes place. + +- qcom,pin-ctrl-enable: + Usage: optional + Value type: <u32> + Description: Bit mask specifying which hardware pins should be used to + enable the regulator, if any; supported bits are: + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + +- qcom,pin-ctrl-hpm: + Usage: optional + Value type: <u32> + Description: Bit mask specifying which hardware pins should be used to + force the regulator into high power mode, if any; + supported bits are: + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + BIT(4) = follow PMIC awake state + +- qcom,vs-soft-start-strength: + Usage: optional + Value type: <u32> + Description: This property sets the soft start strength for voltage + switch type regulators; supported values are: + 0 = 0.05 uA + 1 = 0.25 uA + 2 = 0.55 uA + 3 = 0.75 uA Example: |