diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 6 | ||||
| -rw-r--r-- | Documentation/hwmon/adt7473 | 74 |
2 files changed, 0 insertions, 80 deletions
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 03497909539e..8debdd625e1a 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -449,12 +449,6 @@ Who: Alok N Kataria <akataria@vmware.com> ---------------------------- -What: adt7473 hardware monitoring driver -When: February 2010 -Why: Obsoleted by the adt7475 driver. -Who: Jean Delvare <khali@linux-fr.org> - ---------------------------- What: Support for lcd_switch and display_get in asus-laptop driver When: March 2010 Why: These two features use non-standard interfaces. There are the diff --git a/Documentation/hwmon/adt7473 b/Documentation/hwmon/adt7473 deleted file mode 100644 index 446612bd1fb9..000000000000 --- a/Documentation/hwmon/adt7473 +++ /dev/null @@ -1,74 +0,0 @@ -Kernel driver adt7473 -====================== - -Supported chips: - * Analog Devices ADT7473 - Prefix: 'adt7473' - Addresses scanned: I2C 0x2C, 0x2D, 0x2E - Datasheet: Publicly available at the Analog Devices website - -Author: Darrick J. Wong - -This driver is depreacted, please use the adt7475 driver instead. - -Description ------------ - -This driver implements support for the Analog Devices ADT7473 chip family. - -The ADT7473 uses the 2-wire interface compatible with the SMBUS 2.0 -specification. Using an analog to digital converter it measures three (3) -temperatures and two (2) voltages. It has four (4) 16-bit counters for -measuring fan speed. There are three (3) PWM outputs that can be used -to control fan speed. - -A sophisticated control system for the PWM outputs is designed into the -ADT7473 that allows fan speed to be adjusted automatically based on any of the -three temperature sensors. Each PWM output is individually adjustable and -programmable. Once configured, the ADT7473 will adjust the PWM outputs in -response to the measured temperatures without further host intervention. -This feature can also be disabled for manual control of the PWM's. - -Each of the measured inputs (voltage, temperature, fan speed) has -corresponding high/low limit values. The ADT7473 will signal an ALARM if -any measured value exceeds either limit. - -The ADT7473 samples all inputs continuously. The driver will not read -the registers more often than once every other second. Further, -configuration data is only read once per minute. - -Special Features ----------------- - -The ADT7473 have a 10-bit ADC and can therefore measure temperatures -with 0.25 degC resolution. Temperature readings can be configured either -for twos complement format or "Offset 64" format, wherein 63 is subtracted -from the raw value to get the temperature value. - -The Analog Devices datasheet is very detailed and describes a procedure for -determining an optimal configuration for the automatic PWM control. - -Configuration Notes -------------------- - -Besides standard interfaces driver adds the following: - -* PWM Control - -* pwm#_auto_point1_pwm and temp#_auto_point1_temp and -* pwm#_auto_point2_pwm and temp#_auto_point2_temp - - -point1: Set the pwm speed at a lower temperature bound. -point2: Set the pwm speed at a higher temperature bound. - -The ADT7473 will scale the pwm between the lower and higher pwm speed when -the temperature is between the two temperature boundaries. PWM values range -from 0 (off) to 255 (full speed). Fan speed will be set to maximum when the -temperature sensor associated with the PWM control exceeds temp#_max. - -Notes ------ - -The NVIDIA binary driver presents an ADT7473 chip via an on-card i2c bus. -Unfortunately, they fail to set the i2c adapter class, so this driver may -fail to find the chip until the nvidia driver is patched. |