diff options
Diffstat (limited to 'Documentation')
6 files changed, 94 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index ea5e26f16aec..14d5c2af26f4 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -102,6 +102,7 @@ Exynos4 SoC and this is specified where applicable. sclk_spi0_isp 174 Exynos4x12 sclk_spi1_isp 175 Exynos4x12 sclk_uart_isp 176 Exynos4x12 + sclk_fimg2d 177 [Peripheral Clock Gates] @@ -129,7 +130,7 @@ Exynos4 SoC and this is specified where applicable. smmu_mfcl 274 smmu_mfcr 275 g3d 276 - g2d 277 Exynos4210 + g2d 277 rotator 278 Exynos4210 mdma 279 Exynos4210 smmu_g2d 280 Exynos4210 diff --git a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt index 2b14a940eb75..3f454ffc654a 100644 --- a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt +++ b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt @@ -10,11 +10,16 @@ Required properties: mapped region. - interrupts : G2D interrupt number to the CPU. + - clocks : from common clock binding: handle to G2D clocks. + - clock-names : from common clock binding: must contain "sclk_fimg2d" and + "fimg2d", corresponding to entries in the clocks property. Example: g2d@12800000 { compatible = "samsung,s5pv210-g2d"; reg = <0x12800000 0x1000>; interrupts = <0 89 0>; + clocks = <&clock 177>, <&clock 277>; + clock-names = "sclk_fimg2d", "fimg2d"; status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt index bf0182d8da25..df37b0230c75 100644 --- a/Documentation/devicetree/bindings/media/s5p-mfc.txt +++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt @@ -15,6 +15,9 @@ Required properties: mapped region. - interrupts : MFC interrupt number to the CPU. + - clocks : from common clock binding: handle to mfc clocks. + - clock-names : from common clock binding: must contain "sclk_mfc" and "mfc", + corresponding to entries in the clocks property. - samsung,mfc-r : Base address of the first memory bank used by MFC for DMA contiguous memory allocation and its size. @@ -34,6 +37,8 @@ mfc: codec@13400000 { reg = <0x13400000 0x10000>; interrupts = <0 94 0>; samsung,power-domain = <&pd_mfc>; + clocks = <&clock 170>, <&clock 273>; + clock-names = "sclk_mfc", "mfc"; }; Board specific DT entry: diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt index b2bc219e2003..72e9cd1e89b7 100644 --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -25,8 +25,18 @@ Required Properties: - gpio-controller: identifies the node as a gpio controller and pin bank. - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO - binding is used, the amount of cells must be specified as 2. See generic - GPIO binding documentation for description of particular cells. + binding is used, the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + + Eg: <&gpx2 6 0> + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [flags]> + + Values for gpio specifier: + - Pin number: is a value between 0 to 7. + - Flags: 0 - Active High + 1 - Active Low - Pin mux/config groups as child nodes: The pin mux (selecting pin function mode) and pin config (pull up/down, driver strength) settings are represented @@ -274,3 +284,33 @@ Example 4: Set up the default pin state for uart controller. pinctrl = devm_pinctrl_get_select_default(&pdev->dev); } + +Example 5: A display port client node that supports 'default' pinctrl state + and gpio binding. + + display-port-controller { + /* ... */ + + samsung,hpd-gpio = <&gpx2 6 0>; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + }; + +Example 6: Request the gpio for display port controller + + static int exynos_dp_probe(struct platform_device *pdev) + { + int hpd_gpio, ret; + struct device *dev = &pdev->dev; + struct device_node *dp_node = dev->of_node; + + /* ... */ + + hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0); + + /* ... */ + + ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN, + "hpd_gpio"); + /* ... */ + } diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index b3abde736017..d967ba16de60 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -48,3 +48,37 @@ Example: clocks = <&clock 285>; clock-names = "usbhost"; }; + +DWC3 +Required properties: + - compatible: should be "samsung,exynos5250-dwusb3" for USB 3.0 DWC3 + controller. + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property. + - ranges: allows valid 1:1 translation between child's address space and + parent's address space + - clocks: Clock IDs array as required by the controller. + - clock-names: names of clocks correseponding to IDs in the clock property + +Sub-nodes: +The dwc3 core should be added as subnode to Exynos dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +Example: + usb@12000000 { + compatible = "samsung,exynos5250-dwusb3"; + clocks = <&clock 286>; + clock-names = "usbdrd30"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dwc3 { + compatible = "synopsys,dwc3"; + reg = <0x12000000 0x10000>; + interrupts = <0 72 0>; + usb-phy = <&usb2_phy &usb3_phy>; + }; + }; diff --git a/Documentation/devicetree/bindings/video/exynos_dp.txt b/Documentation/devicetree/bindings/video/exynos_dp.txt index c60da67a5d76..84f10c16cb38 100644 --- a/Documentation/devicetree/bindings/video/exynos_dp.txt +++ b/Documentation/devicetree/bindings/video/exynos_dp.txt @@ -21,6 +21,10 @@ Required properties for dp-controller: of memory mapped region. -interrupts: interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". -interrupt-parent: phandle to Interrupt combiner node. -samsung,color-space: @@ -61,6 +65,8 @@ SOC specific portion: reg = <0x145b0000 0x10000>; interrupts = <10 3>; interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; dptx-phy { reg = <0x10040720>; |