diff options
Diffstat (limited to 'Documentation')
6 files changed, 325 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/arm/arm,scpi.txt b/Documentation/devicetree/bindings/arm/arm,scpi.txt new file mode 100644 index 000000000000..86302de67c2c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/arm,scpi.txt @@ -0,0 +1,188 @@ +System Control and Power Interface (SCPI) Message Protocol +---------------------------------------------------------- + +Firmware implementing the SCPI described in ARM document number ARM DUI 0922B +("ARM Compute Subsystem SCP: Message Interface Protocols")[0] can be used +by Linux to initiate various system control and power operations. + +Required properties: + +- compatible : should be "arm,scpi" +- mboxes: List of phandle and mailbox channel specifiers + All the channels reserved by remote SCP firmware for use by + SCPI message protocol should be specified in any order +- shmem : List of phandle pointing to the shared memory(SHM) area between the + processors using these mailboxes for IPC, one for each mailbox + SHM can be any memory reserved for the purpose of this communication + between the processors. + +See Documentation/devicetree/bindings/mailbox/mailbox.txt +for more details about the generic mailbox controller and +client driver bindings. + +Clock bindings for the clocks based on SCPI Message Protocol +------------------------------------------------------------ + +This binding uses the common clock binding[1]. + +Container Node +============== +Required properties: +- compatible : should be "arm,scpi-clocks" + All the clocks provided by SCP firmware via SCPI message + protocol much be listed as sub-nodes under this node. + +Sub-nodes +========= +Required properties: +- compatible : shall include one of the following + "arm,scpi-dvfs-clocks" - all the clocks that are variable and index based. + These clocks don't provide an entire range of values between the + limits but only discrete points within the range. The firmware + provides the mapping for each such operating frequency and the + index associated with it. The firmware also manages the + voltage scaling appropriately with the clock scaling. + "arm,scpi-variable-clocks" - all the clocks that are variable and provide full + range within the specified range. The firmware provides the + range of values within a specified range. + +Other required properties for all clocks(all from common clock binding): +- #clock-cells : Should be 1. Contains the Clock ID value used by SCPI commands. +- clock-output-names : shall be the corresponding names of the outputs. +- clock-indices: The identifying number for the clocks(i.e.clock_id) in the + node. It can be non linear and hence provide the mapping of identifiers + into the clock-output-names array. + +SRAM and Shared Memory for SCPI +------------------------------- + +A small area of SRAM is reserved for SCPI communication between application +processors and SCP. + +Required properties: +- compatible : should be "arm,juno-sram-ns" for Non-secure SRAM on Juno + +The rest of the properties should follow the generic mmio-sram description +found in ../../misc/sysram.txt + +Each sub-node represents the reserved area for SCPI. + +Required sub-node properties: +- reg : The base offset and size of the reserved area with the SRAM +- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based + shared memory on Juno platforms + +Sensor bindings for the sensors based on SCPI Message Protocol +-------------------------------------------------------------- +SCPI provides an API to access the various sensors on the SoC. + +Required properties: +- compatible : should be "arm,scpi-sensors". +- #thermal-sensor-cells: should be set to 1. This property follows the + thermal device tree bindings[2]. + + Valid cell values are raw identifiers (Sensor + ID) as used by the firmware. Refer to + platform documentation for your + implementation for the IDs to use. For Juno + R0 and Juno R1 refer to [3]. + +[0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/thermal/thermal.txt +[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html + +Example: + +sram: sram@50000000 { + compatible = "arm,juno-sram-ns", "mmio-sram"; + reg = <0x0 0x50000000 0x0 0x10000>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x10000>; + + cpu_scp_lpri: scp-shmem@0 { + compatible = "arm,juno-scp-shmem"; + reg = <0x0 0x200>; + }; + + cpu_scp_hpri: scp-shmem@200 { + compatible = "arm,juno-scp-shmem"; + reg = <0x200 0x200>; + }; +}; + +mailbox: mailbox0@40000000 { + .... + #mbox-cells = <1>; +}; + +scpi_protocol: scpi@2e000000 { + compatible = "arm,scpi"; + mboxes = <&mailbox 0 &mailbox 1>; + shmem = <&cpu_scp_lpri &cpu_scp_hpri>; + + clocks { + compatible = "arm,scpi-clocks"; + + scpi_dvfs: scpi_clocks@0 { + compatible = "arm,scpi-dvfs-clocks"; + #clock-cells = <1>; + clock-indices = <0>, <1>, <2>; + clock-output-names = "atlclk", "aplclk","gpuclk"; + }; + scpi_clk: scpi_clocks@3 { + compatible = "arm,scpi-variable-clocks"; + #clock-cells = <1>; + clock-indices = <3>, <4>; + clock-output-names = "pxlclk0", "pxlclk1"; + }; + }; + + scpi_sensors0: sensors { + compatible = "arm,scpi-sensors"; + #thermal-sensor-cells = <1>; + }; +}; + +cpu@0 { + ... + reg = <0 0>; + clocks = <&scpi_dvfs 0>; +}; + +hdlcd@7ff60000 { + ... + reg = <0 0x7ff60000 0 0x1000>; + clocks = <&scpi_clk 4>; +}; + +thermal-zones { + soc_thermal { + polling-delay-passive = <100>; + polling-delay = <1000>; + + /* sensor ID */ + thermal-sensors = <&scpi_sensors0 3>; + ... + }; +}; + +In the above example, the #clock-cells is set to 1 as required. +scpi_dvfs has 3 output clocks namely: atlclk, aplclk, and gpuclk with 0, +1 and 2 as clock-indices. scpi_clk has 2 output clocks namely: pxlclk0 +and pxlclk1 with 3 and 4 as clock-indices. + +The first consumer in the example is cpu@0 and it has '0' as the clock +specifier which points to the first entry in the output clocks of +scpi_dvfs i.e. "atlclk". + +Similarly the second example is hdlcd@7ff60000 and it has pxlclk1 as input +clock. '4' in the clock specifier here points to the second entry +in the output clocks of scpi_clocks i.e. "pxlclk1" + +The thermal-sensors property in the soc_thermal node uses the +temperature sensor provided by SCP firmware to setup a thermal +zone. The ID "3" is the sensor identifier for the temperature sensor +as used by the firmware. diff --git a/Documentation/devicetree/bindings/arm/psci.txt b/Documentation/devicetree/bindings/arm/psci.txt index 5aa40ede0e99..a9adab84e2fe 100644 --- a/Documentation/devicetree/bindings/arm/psci.txt +++ b/Documentation/devicetree/bindings/arm/psci.txt @@ -31,6 +31,10 @@ Main node required properties: support, but are permitted to be present for compatibility with existing software when "arm,psci" is later in the compatible list. + * "arm,psci-1.0" : for implementations complying to PSCI 1.0. PSCI 1.0 is + backward compatible with PSCI 0.2 with minor specification updates, + as defined in the PSCI specification[2]. + - method : The method of calling the PSCI firmware. Permitted values are: @@ -100,3 +104,5 @@ Case 3: PSCI v0.2 and PSCI v0.1. [1] Kernel documentation - ARM idle states bindings Documentation/devicetree/bindings/arm/idle-states.txt +[2] Power State Coordination Interface (PSCI) specification + http://infocenter.arm.com/help/topic/com.arm.doc.den0022c/DEN0022C_Power_State_Coordination_Interface.pdf diff --git a/Documentation/devicetree/bindings/bus/sunxi-rsb.txt b/Documentation/devicetree/bindings/bus/sunxi-rsb.txt new file mode 100644 index 000000000000..3dd28343b6ce --- /dev/null +++ b/Documentation/devicetree/bindings/bus/sunxi-rsb.txt @@ -0,0 +1,47 @@ +Allwinner Reduced Serial Bus (RSB) controller + +The RSB controller found on later Allwinner SoCs is an SMBus like 2 wire +serial bus with 1 master and up to 15 slaves. It is represented by a node +for the controller itself, and child nodes representing the slave devices. + +Required properties : + + - reg : Offset and length of the register set for the controller. + - compatible : Shall be "allwinner,sun8i-a23-rsb". + - interrupts : The interrupt line associated to the RSB controller. + - clocks : The gate clk associated to the RSB controller. + - resets : The reset line associated to the RSB controller. + - #address-cells : shall be 1 + - #size-cells : shall be 0 + +Optional properties : + + - clock-frequency : Desired RSB bus clock frequency in Hz. Maximum is 20MHz. + If not set this defaults to 3MHz. + +Child nodes: + +An RSB controller node can contain zero or more child nodes representing +slave devices on the bus. Child 'reg' properties should contain the slave +device's hardware address. The hardware address is hardwired in the device, +which can normally be found in the datasheet. + +Example: + + rsb@01f03400 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x01f03400 0x400>; + interrupts = <0 39 4>; + clocks = <&apb0_gates 3>; + clock-frequency = <3000000>; + resets = <&apb0_rst 3>; + #address-cells = <1>; + #size-cells = <0>; + + pmic@3e3 { + compatible = "..."; + reg = <0x3e3>; + + /* ... */ + }; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt index e6df32f9986d..22b77ee02f58 100644 --- a/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt +++ b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt @@ -1,8 +1,9 @@ -* Device tree bindings for ARM PL172 MultiPort Memory Controller +* Device tree bindings for ARM PL172/PL175/PL176 MultiPort Memory Controller Required properties: -- compatible: "arm,pl172", "arm,primecell" +- compatible: Must be "arm,primecell" and exactly one from + "arm,pl172", "arm,pl175" or "arm,pl176". - reg: Must contains offset/length value for controller. @@ -56,7 +57,8 @@ Optional child cs node config properties: - mpmc,extended-wait: Enable extended wait. -- mpmc,buffer-enable: Enable write buffer. +- mpmc,buffer-enable: Enable write buffer, option is not supported by + PL175 and PL176 controllers. - mpmc,write-protect: Enable write protect. diff --git a/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt new file mode 100644 index 000000000000..112756e11802 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/rockchip/power_domain.txt @@ -0,0 +1,46 @@ +* Rockchip Power Domains + +Rockchip processors include support for multiple power domains which can be +powered up/down by software based on different application scenes to save power. + +Required properties for power domain controller: +- compatible: Should be one of the following. + "rockchip,rk3288-power-controller" - for RK3288 SoCs. +- #power-domain-cells: Number of cells in a power-domain specifier. + Should be 1 for multiple PM domains. +- #address-cells: Should be 1. +- #size-cells: Should be 0. + +Required properties for power domain sub nodes: +- reg: index of the power domain, should use macros in: + "include/dt-bindings/power/rk3288-power.h" - for RK3288 type power domain. +- clocks (optional): phandles to clocks which need to be enabled while power domain + switches state. + +Example: + + power: power-controller { + compatible = "rockchip,rk3288-power-controller"; + #power-domain-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + pd_gpu { + reg = <RK3288_PD_GPU>; + clocks = <&cru ACLK_GPU>; + }; + }; + +Node of a device using power domains must have a power-domains property, +containing a phandle to the power device node and an index specifying which +power domain to use. +The index should use macros in: + "include/dt-bindings/power/rk3288-power.h" - for rk3288 type power domain. + +Example of the node using power domain: + + node { + /* ... */ + power-domains = <&power RK3288_PD_GPU>; + /* ... */ + }; diff --git a/Documentation/hwmon/scpi-hwmon b/Documentation/hwmon/scpi-hwmon new file mode 100644 index 000000000000..4cfcdf2d5eab --- /dev/null +++ b/Documentation/hwmon/scpi-hwmon @@ -0,0 +1,33 @@ +Kernel driver scpi-hwmon +======================== + +Supported chips: + * Chips based on ARM System Control Processor Interface + Addresses scanned: - + Datasheet: http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/index.html + +Author: Punit Agrawal <punit.agrawal@arm.com> + +Description +----------- + +This driver supports hardware monitoring for SoC's based on the ARM +System Control Processor (SCP) implementing the System Control +Processor Interface (SCPI). The following sensor types are supported +by the SCP - + + * temperature + * voltage + * current + * power + +The SCP interface provides an API to query the available sensors and +their values which are then exported to userspace by this driver. + +Usage Notes +----------- + +The driver relies on device tree node to indicate the presence of SCPI +support in the kernel. See +Documentation/devicetree/bindings/arm/arm,scpi.txt for details of the +devicetree node.
\ No newline at end of file |