diff options
Diffstat (limited to 'Documentation')
8 files changed, 12 insertions, 12 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-iio-vf610 b/Documentation/ABI/testing/sysfs-bus-iio-vf610 index 308a6756d3bf..491ead804488 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-vf610 +++ b/Documentation/ABI/testing/sysfs-bus-iio-vf610 @@ -1,4 +1,4 @@ -What: /sys/bus/iio/devices/iio:deviceX/conversion_mode +What: /sys/bus/iio/devices/iio:deviceX/in_conversion_mode KernelVersion: 4.2 Contact: linux-iio@vger.kernel.org Description: diff --git a/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml b/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml index ece261b8e963..7326c0a28d16 100644 --- a/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml +++ b/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml @@ -47,6 +47,5 @@ examples: clocks = <&clkcfg CLK_SPI0>; interrupt-parent = <&plic>; interrupts = <54>; - spi-max-frequency = <25000000>; }; ... diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml index e2c7b934c50d..78ceb9d67754 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml +++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml @@ -110,7 +110,6 @@ examples: pinctrl-names = "default"; pinctrl-0 = <&qup_spi1_default>; interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>; - spi-max-frequency = <50000000>; #address-cells = <1>; #size-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/usb/generic-ehci.yaml b/Documentation/devicetree/bindings/usb/generic-ehci.yaml index 0b4524b6409e..1e84e1b7ab27 100644 --- a/Documentation/devicetree/bindings/usb/generic-ehci.yaml +++ b/Documentation/devicetree/bindings/usb/generic-ehci.yaml @@ -136,7 +136,8 @@ properties: Phandle of a companion. phys: - maxItems: 1 + minItems: 1 + maxItems: 3 phy-names: const: usb diff --git a/Documentation/devicetree/bindings/usb/generic-ohci.yaml b/Documentation/devicetree/bindings/usb/generic-ohci.yaml index e2ac84665316..bb6bbd5f129d 100644 --- a/Documentation/devicetree/bindings/usb/generic-ohci.yaml +++ b/Documentation/devicetree/bindings/usb/generic-ohci.yaml @@ -103,7 +103,8 @@ properties: Overrides the detected port count phys: - maxItems: 1 + minItems: 1 + maxItems: 3 phy-names: const: usb diff --git a/Documentation/driver-api/gpio/board.rst b/Documentation/driver-api/gpio/board.rst index 4e3adf31c8d1..b33aa04f213f 100644 --- a/Documentation/driver-api/gpio/board.rst +++ b/Documentation/driver-api/gpio/board.rst @@ -6,7 +6,7 @@ This document explains how GPIOs can be assigned to given devices and functions. Note that it only applies to the new descriptor-based interface. For a description of the deprecated integer-based GPIO interface please refer to -gpio-legacy.txt (actually, there is no real mapping possible with the old +legacy.rst (actually, there is no real mapping possible with the old interface; you just fetch an integer from somewhere and request the corresponding GPIO). diff --git a/Documentation/driver-api/gpio/consumer.rst b/Documentation/driver-api/gpio/consumer.rst index 47869ca8ccf0..72bcf5f5e3a2 100644 --- a/Documentation/driver-api/gpio/consumer.rst +++ b/Documentation/driver-api/gpio/consumer.rst @@ -4,7 +4,7 @@ GPIO Descriptor Consumer Interface This document describes the consumer interface of the GPIO framework. Note that it describes the new descriptor-based interface. For a description of the -deprecated integer-based GPIO interface please refer to gpio-legacy.txt. +deprecated integer-based GPIO interface please refer to legacy.rst. Guidelines for GPIOs consumers @@ -78,7 +78,7 @@ whether the line is configured active high or active low (see The two last flags are used for use cases where open drain is mandatory, such as I2C: if the line is not already configured as open drain in the mappings -(see board.txt), then open drain will be enforced anyway and a warning will be +(see board.rst), then open drain will be enforced anyway and a warning will be printed that the board configuration needs to be updated to match the use case. Both functions return either a valid GPIO descriptor, or an error code checkable @@ -270,7 +270,7 @@ driven. The same is applicable for open drain or open source output lines: those do not actively drive their output high (open drain) or low (open source), they just switch their output to a high impedance value. The consumer should not need to -care. (For details read about open drain in driver.txt.) +care. (For details read about open drain in driver.rst.) With this, all the gpiod_set_(array)_value_xxx() functions interpret the parameter "value" as "asserted" ("1") or "de-asserted" ("0"). The physical line diff --git a/Documentation/driver-api/gpio/intro.rst b/Documentation/driver-api/gpio/intro.rst index 2e924fb5b3d5..c9c19243b97f 100644 --- a/Documentation/driver-api/gpio/intro.rst +++ b/Documentation/driver-api/gpio/intro.rst @@ -14,12 +14,12 @@ Due to the history of GPIO interfaces in the kernel, there are two different ways to obtain and use GPIOs: - The descriptor-based interface is the preferred way to manipulate GPIOs, - and is described by all the files in this directory excepted gpio-legacy.txt. + and is described by all the files in this directory excepted legacy.rst. - The legacy integer-based interface which is considered deprecated (but still - usable for compatibility reasons) is documented in gpio-legacy.txt. + usable for compatibility reasons) is documented in legacy.rst. The remainder of this document applies to the new descriptor-based interface. -gpio-legacy.txt contains the same information applied to the legacy +legacy.rst contains the same information applied to the legacy integer-based interface. |