summaryrefslogtreecommitdiffstats
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/ABI/testing/sysfs-firmware-ofw26
-rw-r--r--Documentation/devicetree/bindings/arm/cci.txt15
-rw-r--r--Documentation/devicetree/bindings/arm/cpus.txt13
-rw-r--r--Documentation/devicetree/bindings/arm/idle-states.txt4
-rw-r--r--Documentation/devicetree/bindings/arm/l2c2x0.txt4
-rw-r--r--Documentation/devicetree/bindings/arm/topology.txt4
-rw-r--r--Documentation/devicetree/bindings/bus/simple-pm-bus.txt2
-rw-r--r--Documentation/devicetree/bindings/chosen.txt3
-rw-r--r--Documentation/devicetree/bindings/common-properties.txt2
-rw-r--r--Documentation/devicetree/bindings/crypto/fsl-sec4.txt4
-rw-r--r--Documentation/devicetree/bindings/crypto/fsl-sec6.txt4
-rw-r--r--Documentation/devicetree/bindings/display/panel/display-timing.txt16
-rw-r--r--Documentation/devicetree/bindings/graph.txt13
-rw-r--r--Documentation/devicetree/bindings/iio/proximity/as3935.txt2
-rw-r--r--Documentation/devicetree/bindings/interrupt-controller/open-pic.txt5
-rw-r--r--Documentation/devicetree/bindings/net/ethernet.txt9
-rw-r--r--Documentation/devicetree/bindings/net/fsl-fman.txt (renamed from Documentation/devicetree/bindings/powerpc/fsl/fman.txt)0
-rw-r--r--Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt2
-rw-r--r--Documentation/devicetree/bindings/powerpc/fsl/cpus.txt6
-rw-r--r--Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt2
-rw-r--r--Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt4
-rw-r--r--Documentation/devicetree/bindings/powerpc/fsl/srio.txt3
-rw-r--r--Documentation/devicetree/bindings/thermal/brcm,ns-thermal.txt (renamed from Documentation/devicetree/bindings/thermal/brcm,ns-thermal)0
-rw-r--r--Documentation/devicetree/bindings/usb/exynos-usb.txt4
-rw-r--r--Documentation/devicetree/bindings/vendor-prefixes.txt6
-rw-r--r--Documentation/devicetree/booting-without-of.txt2
-rw-r--r--Documentation/devicetree/overlay-notes.txt8
-rw-r--r--Documentation/devicetree/usage-model.txt2
-rw-r--r--Documentation/printk-formats.txt36
-rw-r--r--Documentation/xtensa/mmu.txt6
30 files changed, 137 insertions, 70 deletions
diff --git a/Documentation/ABI/testing/sysfs-firmware-ofw b/Documentation/ABI/testing/sysfs-firmware-ofw
index f562b188e71d..edcab3ccfcc0 100644
--- a/Documentation/ABI/testing/sysfs-firmware-ofw
+++ b/Documentation/ABI/testing/sysfs-firmware-ofw
@@ -1,6 +1,6 @@
What: /sys/firmware/devicetree/*
Date: November 2013
-Contact: Grant Likely <grant.likely@linaro.org>
+Contact: Grant Likely <grant.likely@arm.com>, devicetree@vger.kernel.org
Description:
When using OpenFirmware or a Flattened Device Tree to enumerate
hardware, the device tree structure will be exposed in this
@@ -26,3 +26,27 @@ Description:
name plus address). Properties are represented as files
in the directory. The contents of each file is the exact
binary data from the device tree.
+
+What: /sys/firmware/fdt
+Date: February 2015
+KernelVersion: 3.19
+Contact: Frank Rowand <frowand.list@gmail.com>, devicetree@vger.kernel.org
+Description:
+ Exports the FDT blob that was passed to the kernel by
+ the bootloader. This allows userland applications such
+ as kexec to access the raw binary. This blob is also
+ useful when debugging since it contains any changes
+ made to the blob by the bootloader.
+
+ The fact that this node does not reside under
+ /sys/firmware/device-tree is deliberate: FDT is also used
+ on arm64 UEFI/ACPI systems to communicate just the UEFI
+ and ACPI entry points, but the FDT is never unflattened
+ and used to configure the system.
+
+ A CRC32 checksum is calculated over the entire FDT
+ blob, and verified at late_initcall time. The sysfs
+ entry is instantiated only if the checksum is valid,
+ i.e., if the FDT blob has not been modified in the mean
+ time. Otherwise, a warning is printed.
+Users: kexec, debugging
diff --git a/Documentation/devicetree/bindings/arm/cci.txt b/Documentation/devicetree/bindings/arm/cci.txt
index 0f2153e8fa7e..9600761f2d5b 100644
--- a/Documentation/devicetree/bindings/arm/cci.txt
+++ b/Documentation/devicetree/bindings/arm/cci.txt
@@ -11,13 +11,6 @@ clusters, through memory mapped interface, with a global control register
space and multiple sets of interface control registers, one per slave
interface.
-Bindings for the CCI node follow the ePAPR standard, available from:
-
-www.power.org/documentation/epapr-version-1-1/
-
-with the addition of the bindings described in this document which are
-specific to ARM.
-
* CCI interconnect node
Description: Describes a CCI cache coherent Interconnect component
@@ -50,10 +43,10 @@ specific to ARM.
as a tuple of cells, containing child address,
parent address and the size of the region in the
child address space.
- Definition: A standard property. Follow rules in the ePAPR for
- hierarchical bus addressing. CCI interfaces
- addresses refer to the parent node addressing
- scheme to declare their register bases.
+ Definition: A standard property. Follow rules in the Devicetree
+ Specification for hierarchical bus addressing. CCI
+ interfaces addresses refer to the parent node
+ addressing scheme to declare their register bases.
CCI interconnect node can define the following child nodes:
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index ad1913bea8d7..a44253cad269 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -6,9 +6,9 @@ The device tree allows to describe the layout of CPUs in a system through
the "cpus" node, which in turn contains a number of subnodes (ie "cpu")
defining properties for every cpu.
-Bindings for CPU nodes follow the ePAPR v1.1 standard, available from:
+Bindings for CPU nodes follow the Devicetree Specification, available from:
-https://www.power.org/documentation/epapr-version-1-1/
+https://www.devicetree.org/specifications/
with updates for 32-bit and 64-bit ARM systems provided in this document.
@@ -16,8 +16,8 @@ with updates for 32-bit and 64-bit ARM systems provided in this document.
Convention used in this document
================================
-This document follows the conventions described in the ePAPR v1.1, with
-the addition:
+This document follows the conventions described in the Devicetree
+Specification, with the addition:
- square brackets define bitfields, eg reg[7:0] value of the bitfield in
the reg property contained in bits 7 down to 0
@@ -26,8 +26,9 @@ the addition:
cpus and cpu node bindings definition
=====================================
-The ARM architecture, in accordance with the ePAPR, requires the cpus and cpu
-nodes to be present and contain the properties described below.
+The ARM architecture, in accordance with the Devicetree Specification,
+requires the cpus and cpu nodes to be present and contain the properties
+described below.
- cpus node
diff --git a/Documentation/devicetree/bindings/arm/idle-states.txt b/Documentation/devicetree/bindings/arm/idle-states.txt
index b8e41c148a3c..7a591333f2b1 100644
--- a/Documentation/devicetree/bindings/arm/idle-states.txt
+++ b/Documentation/devicetree/bindings/arm/idle-states.txt
@@ -695,5 +695,5 @@ cpus {
[4] ARM Architecture Reference Manuals
http://infocenter.arm.com/help/index.jsp
-[5] ePAPR standard
- https://www.power.org/documentation/epapr-version-1-1/
+[5] Devicetree Specification
+ https://www.devicetree.org/specifications/
diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt
index d9650c1788f4..fbe6cb21f4cf 100644
--- a/Documentation/devicetree/bindings/arm/l2c2x0.txt
+++ b/Documentation/devicetree/bindings/arm/l2c2x0.txt
@@ -4,8 +4,8 @@ ARM cores often have a separate L2C210/L2C220/L2C310 (also known as PL210/PL220/
PL310 and variants) based level 2 cache controller. All these various implementations
of the L2 cache controller have compatible programming models (Note 1).
Some of the properties that are just prefixed "cache-*" are taken from section
-3.7.3 of the ePAPR v1.1 specification which can be found at:
-https://www.power.org/wp-content/uploads/2012/06/Power_ePAPR_APPROVED_v1.1.pdf
+3.7.3 of the Devicetree Specification which can be found at:
+https://www.devicetree.org/specifications/
The ARM L2 cache representation in the device tree should be done as follows:
diff --git a/Documentation/devicetree/bindings/arm/topology.txt b/Documentation/devicetree/bindings/arm/topology.txt
index 1061faf5f602..de9eb0486630 100644
--- a/Documentation/devicetree/bindings/arm/topology.txt
+++ b/Documentation/devicetree/bindings/arm/topology.txt
@@ -29,9 +29,9 @@ corresponding to the system hierarchy; syntactically they are defined as device
tree nodes.
The remainder of this document provides the topology bindings for ARM, based
-on the ePAPR standard, available from:
+on the Devicetree Specification, available from:
-http://www.power.org/documentation/epapr-version-1-1/
+https://www.devicetree.org/specifications/
If not stated otherwise, whenever a reference to a cpu node phandle is made its
value must point to a cpu node compliant with the cpu node bindings as
diff --git a/Documentation/devicetree/bindings/bus/simple-pm-bus.txt b/Documentation/devicetree/bindings/bus/simple-pm-bus.txt
index d032237512c2..6f15037131ed 100644
--- a/Documentation/devicetree/bindings/bus/simple-pm-bus.txt
+++ b/Documentation/devicetree/bindings/bus/simple-pm-bus.txt
@@ -10,7 +10,7 @@ enabled for child devices connected to the bus (either on-SoC or externally)
to function.
While "simple-pm-bus" follows the "simple-bus" set of properties, as specified
-in ePAPR, it is not an extension of "simple-bus".
+in the Devicetree Specification, it is not an extension of "simple-bus".
Required properties:
diff --git a/Documentation/devicetree/bindings/chosen.txt b/Documentation/devicetree/bindings/chosen.txt
index b5e39af4ddc0..dee3f5d9df26 100644
--- a/Documentation/devicetree/bindings/chosen.txt
+++ b/Documentation/devicetree/bindings/chosen.txt
@@ -10,7 +10,8 @@ stdout-path property
--------------------
Device trees may specify the device to be used for boot console output
-with a stdout-path property under /chosen, as described in ePAPR, e.g.
+with a stdout-path property under /chosen, as described in the Devicetree
+Specification, e.g.
/ {
chosen {
diff --git a/Documentation/devicetree/bindings/common-properties.txt b/Documentation/devicetree/bindings/common-properties.txt
index 3193979b1d05..697714f8d75c 100644
--- a/Documentation/devicetree/bindings/common-properties.txt
+++ b/Documentation/devicetree/bindings/common-properties.txt
@@ -1,6 +1,6 @@
Common properties
-The ePAPR specification does not define any properties related to hardware
+The Devicetree Specification does not define any properties related to hardware
byteswapping, but endianness issues show up frequently in porting Linux to
different machine types. This document attempts to provide a consistent
way of handling byteswapping across drivers.
diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt
index 10a425f451fc..7aef0eae58d4 100644
--- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt
+++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt
@@ -118,8 +118,8 @@ PROPERTIES
Definition: A list of clock name strings in the same order as the
clocks property.
- Note: All other standard properties (see the ePAPR) are allowed
- but are optional.
+ Note: All other standard properties (see the Devicetree Specification)
+ are allowed but are optional.
EXAMPLE
diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec6.txt b/Documentation/devicetree/bindings/crypto/fsl-sec6.txt
index baf8a3c1b469..73b0eb950bb3 100644
--- a/Documentation/devicetree/bindings/crypto/fsl-sec6.txt
+++ b/Documentation/devicetree/bindings/crypto/fsl-sec6.txt
@@ -55,8 +55,8 @@ PROPERTIES
triplet that includes the child address, parent address, &
length.
- Note: All other standard properties (see the ePAPR) are allowed
- but are optional.
+ Note: All other standard properties (see the Devicetree Specification)
+ are allowed but are optional.
EXAMPLE
crypto@a0000 {
diff --git a/Documentation/devicetree/bindings/display/panel/display-timing.txt b/Documentation/devicetree/bindings/display/panel/display-timing.txt
index 81a75893d1b8..58fa3e48481d 100644
--- a/Documentation/devicetree/bindings/display/panel/display-timing.txt
+++ b/Documentation/devicetree/bindings/display/panel/display-timing.txt
@@ -57,11 +57,11 @@ can be specified.
The parameters are defined as:
+----------+-------------------------------------+----------+-------+
- | | ↑ | | |
+ | | ^ | | |
| | |vback_porch | | |
- | | ↓ | | |
+ | | v | | |
+----------#######################################----------+-------+
- | # ↑ # | |
+ | # ^ # | |
| # | # | |
| hback # | # hfront | hsync |
| porch # | hactive # porch | len |
@@ -69,15 +69,15 @@ The parameters are defined as:
| # | # | |
| # |vactive # | |
| # | # | |
- | # ↓ # | |
+ | # v # | |
+----------#######################################----------+-------+
- | | ↑ | | |
+ | | ^ | | |
| | |vfront_porch | | |
- | | ↓ | | |
+ | | v | | |
+----------+-------------------------------------+----------+-------+
- | | ↑ | | |
+ | | ^ | | |
| | |vsync_len | | |
- | | ↓ | | |
+ | | v | | |
+----------+-------------------------------------+----------+-------+
Example:
diff --git a/Documentation/devicetree/bindings/graph.txt b/Documentation/devicetree/bindings/graph.txt
index fcb1c6a4787b..0415e2c53ba0 100644
--- a/Documentation/devicetree/bindings/graph.txt
+++ b/Documentation/devicetree/bindings/graph.txt
@@ -34,7 +34,7 @@ remote device, an 'endpoint' child node must be provided for each link.
If more than one port is present in a device node or there is more than one
endpoint at a port, or a port node needs to be associated with a selected
hardware interface, a common scheme using '#address-cells', '#size-cells'
-and 'reg' properties is used number the nodes.
+and 'reg' properties is used to number the nodes.
device {
...
@@ -89,9 +89,9 @@ Links between endpoints
Each endpoint should contain a 'remote-endpoint' phandle property that points
to the corresponding endpoint in the port of the remote device. In turn, the
-remote endpoint should contain a 'remote-endpoint' property. If it has one,
-it must not point to another than the local endpoint. Two endpoints with their
-'remote-endpoint' phandles pointing at each other form a link between the
+remote endpoint should contain a 'remote-endpoint' property. If it has one, it
+must not point to anything other than the local endpoint. Two endpoints with
+their 'remote-endpoint' phandles pointing at each other form a link between the
containing ports.
device-1 {
@@ -110,13 +110,12 @@ device-2 {
};
};
-
Required properties
-------------------
If there is more than one 'port' or more than one 'endpoint' node or 'reg'
-property is present in port and/or endpoint nodes the following properties
-are required in a relevant parent node:
+property present in the port and/or endpoint nodes then the following
+properties are required in a relevant parent node:
- #address-cells : number of cells required to define port/endpoint
identifier, should be 1.
diff --git a/Documentation/devicetree/bindings/iio/proximity/as3935.txt b/Documentation/devicetree/bindings/iio/proximity/as3935.txt
index ae23dd8da736..38d74314b7ab 100644
--- a/Documentation/devicetree/bindings/iio/proximity/as3935.txt
+++ b/Documentation/devicetree/bindings/iio/proximity/as3935.txt
@@ -3,6 +3,7 @@ Austrian Microsystems AS3935 Franklin lightning sensor device driver
Required properties:
- compatible: must be "ams,as3935"
- reg: SPI chip select number for the device
+ - spi-max-frequency: specifies maximum SPI clock frequency
- spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI
slave node bindings.
- interrupt-parent : should be the phandle for the interrupt controller
@@ -21,6 +22,7 @@ Example:
as3935@0 {
compatible = "ams,as3935";
reg = <0>;
+ spi-max-frequency = <400000>;
spi-cpha;
interrupt-parent = <&gpio1>;
interrupts = <16 1>;
diff --git a/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt b/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt
index 909a902dff85..ccbbfdc53c72 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/open-pic.txt
@@ -92,7 +92,6 @@ Example 2:
* References
-[1] Power.org (TM) Standard for Embedded Power Architecture (TM) Platform
- Requirements (ePAPR), Version 1.0, July 2008.
- (http://www.power.org/resources/downloads/Power_ePAPR_APPROVED_v1.0.pdf)
+[1] Devicetree Specification
+ (https://www.devicetree.org/specifications/)
diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt
index edd7fd2bbbf9..7da86f22a13b 100644
--- a/Documentation/devicetree/bindings/net/ethernet.txt
+++ b/Documentation/devicetree/bindings/net/ethernet.txt
@@ -8,7 +8,8 @@ The following properties are common to the Ethernet controllers:
property;
- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
- the maximum frame size (there's contradiction in ePAPR).
+ the maximum frame size (there's contradiction in the Devicetree
+ Specification).
- phy-mode: string, operation mode of the PHY interface. This is now a de-facto
standard property; supported values are:
* "internal"
@@ -35,9 +36,11 @@ The following properties are common to the Ethernet controllers:
* "rxaui"
* "xaui"
* "10gbase-kr" (10GBASE-KR, XFI, SFI)
-- phy-connection-type: the same as "phy-mode" property but described in ePAPR;
+- phy-connection-type: the same as "phy-mode" property but described in the
+ Devicetree Specification;
- phy-handle: phandle, specifies a reference to a node representing a PHY
- device; this property is described in ePAPR and so preferred;
+ device; this property is described in the Devicetree Specification and so
+ preferred;
- phy: the same as "phy-handle" property, not recommended for new bindings.
- phy-device: the same as "phy-handle" property, not recommended for new
bindings.
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt
index df873d1f3b7c..df873d1f3b7c 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/fman.txt
+++ b/Documentation/devicetree/bindings/net/fsl-fman.txt
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
index 5dbf169cd81c..590f622188de 100644
--- a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
+++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
@@ -31,7 +31,7 @@ mmc3: mmc@01c12000 {
non-removable;
status = "okay";
- brcmf: bcrmf@1 {
+ brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt b/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt
index f8cd2397aa04..d63ab1dec16d 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/cpus.txt
@@ -3,10 +3,10 @@ Power Architecture CPU Binding
Copyright 2013 Freescale Semiconductor Inc.
Power Architecture CPUs in Freescale SOCs are represented in device trees as
-per the definition in ePAPR.
+per the definition in the Devicetree Specification.
-In addition to the ePAPR definitions, the properties defined below may be
-present on CPU nodes.
+In addition to the the Devicetree Specification definitions, the properties
+defined below may be present on CPU nodes.
PROPERTIES
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt b/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt
index dc9bb3182525..8a70696395a7 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/l2cache.txt
@@ -1,7 +1,7 @@
Freescale L2 Cache Controller
L2 cache is present in Freescale's QorIQ and QorIQ Qonverge platforms.
-The cache bindings explained below are ePAPR compliant
+The cache bindings explained below are Devicetree Specification compliant
Required Properties:
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
index b9a8a2bcfae7..0496ada4bba4 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/srio-rmu.txt
@@ -124,8 +124,8 @@ Port-Write Unit:
A single IRQ that handles port-write conditions is
specified by this property. (Typically shared with error).
- Note: All other standard properties (see the ePAPR) are allowed
- but are optional.
+ Note: All other standard properties (see the Devicetree Specification)
+ are allowed but are optional.
Example:
rmu: rmu@d3000 {
diff --git a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
index 07abf0f2f440..86ee6ea73754 100644
--- a/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
+++ b/Documentation/devicetree/bindings/powerpc/fsl/srio.txt
@@ -72,7 +72,8 @@ the following properties:
represents the LIODN associated with maintenance transactions
for the port.
-Note: All other standard properties (see ePAPR) are allowed but are optional.
+Note: All other standard properties (see the Devicetree Specification)
+are allowed but are optional.
Example:
diff --git a/Documentation/devicetree/bindings/thermal/brcm,ns-thermal b/Documentation/devicetree/bindings/thermal/brcm,ns-thermal.txt
index 68e047170039..68e047170039 100644
--- a/Documentation/devicetree/bindings/thermal/brcm,ns-thermal
+++ b/Documentation/devicetree/bindings/thermal/brcm,ns-thermal.txt
diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt
index 9b4dbe3b2acc..78ebebb66dad 100644
--- a/Documentation/devicetree/bindings/usb/exynos-usb.txt
+++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt
@@ -92,6 +92,8 @@ Required properties:
parent's address space
- clocks: Clock IDs array as required by the controller.
- clock-names: names of clocks correseponding to IDs in the clock property
+ - vdd10-supply: 1.0V powr supply
+ - vdd33-supply: 3.0V/3.3V power supply
Sub-nodes:
The dwc3 core should be added as subnode to Exynos dwc3 glue.
@@ -107,6 +109,8 @@ Example:
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ vdd10-supply = <&ldo11_reg>;
+ vdd33-supply = <&ldo9_reg>;
dwc3 {
compatible = "synopsys,dwc3";
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 286f4e1e111f..708ff2504260 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -45,6 +45,7 @@ avia avia semiconductor
avic Shanghai AVIC Optoelectronics Co., Ltd.
axentia Axentia Technologies AB
axis Axis Communications AB
+bananapi BIPAI KEJI LIMITED
boe BOE Technology Group Co., Ltd.
bosch Bosch Sensortec GmbH
boundary Boundary Devices Inc.
@@ -159,6 +160,8 @@ iom Iomega Corporation
isee ISEE 2007 S.L.
isil Intersil
issi Integrated Silicon Solutions Inc.
+itead ITEAD Intelligent Systems Co.Ltd
+iwave iWave Systems Technologies Pvt. Ltd.
jdi Japan Display Inc.
jedec JEDEC Solid State Technology Association
karo Ka-Ro electronics GmbH
@@ -177,6 +180,7 @@ lg LG Corporation
libretech Shenzhen Libre Technology Co., Ltd
licheepi Lichee Pi
linaro Linaro Limited
+linksys Belkin International, Inc. (Linksys)
linux Linux-specific binding
lltc Linear Technology Corporation
lsi LSI Corp. (LSI Logic)
@@ -269,8 +273,10 @@ renesas Renesas Electronics Corporation
richtek Richtek Technology Corporation
ricoh Ricoh Co. Ltd.
rikomagic Rikomagic Tech Corp. Ltd
+riscv RISC-V Foundation
rockchip Fuzhou Rockchip Electronics Co., Ltd
rohm ROHM Semiconductor Co., Ltd
+roofull Shenzhen Roofull Technology Co, Ltd
samsung Samsung Semiconductor
samtec Samtec/Softing company
sandisk Sandisk Corporation
diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt
index 280d283304bb..fb740445199f 100644
--- a/Documentation/devicetree/booting-without-of.txt
+++ b/Documentation/devicetree/booting-without-of.txt
@@ -1413,7 +1413,7 @@ Optional property:
from DMA operations originating from the bus. It provides a means of
defining a mapping or translation between the physical address space of
the bus and the physical address space of the parent of the bus.
- (for more information see ePAPR specification)
+ (for more information see the Devicetree Specification)
* DMA Bus child
Optional property:
diff --git a/Documentation/devicetree/overlay-notes.txt b/Documentation/devicetree/overlay-notes.txt
index d418a6ce9812..eb7f2685fda1 100644
--- a/Documentation/devicetree/overlay-notes.txt
+++ b/Documentation/devicetree/overlay-notes.txt
@@ -3,8 +3,7 @@ Device Tree Overlay Notes
This document describes the implementation of the in-kernel
device tree overlay functionality residing in drivers/of/overlay.c and is a
-companion document to Documentation/devicetree/dt-object-internal.txt[1] &
-Documentation/devicetree/dynamic-resolution-notes.txt[2]
+companion document to Documentation/devicetree/dynamic-resolution-notes.txt[1]
How overlays work
-----------------
@@ -16,8 +15,7 @@ Since the kernel mainly deals with devices, any new device node that result
in an active device should have it created while if the device node is either
disabled or removed all together, the affected device should be deregistered.
-Lets take an example where we have a foo board with the following base tree
-which is taken from [1].
+Lets take an example where we have a foo board with the following base tree:
---- foo.dts -----------------------------------------------------------------
/* FOO platform */
@@ -36,7 +34,7 @@ which is taken from [1].
};
---- foo.dts -----------------------------------------------------------------
-The overlay bar.dts, when loaded (and resolved as described in [2]) should
+The overlay bar.dts, when loaded (and resolved as described in [1]) should
---- bar.dts -----------------------------------------------------------------
/plugin/; /* allow undefined label references and record them */
diff --git a/Documentation/devicetree/usage-model.txt b/Documentation/devicetree/usage-model.txt
index 2b6b3d3f0388..33a8aaac02a8 100644
--- a/Documentation/devicetree/usage-model.txt
+++ b/Documentation/devicetree/usage-model.txt
@@ -387,7 +387,7 @@ static void __init harmony_init_machine(void)
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
-"simple-bus" is defined in the ePAPR 1.0 specification as a property
+"simple-bus" is defined in the Devicetree Specification as a property
meaning a simple memory mapped bus, so the of_platform_populate() code
could be written to just assume simple-bus compatible nodes will
always be traversed. However, we pass it in as an argument so that
diff --git a/Documentation/printk-formats.txt b/Documentation/printk-formats.txt
index 5962949944fd..619cdffa5d44 100644
--- a/Documentation/printk-formats.txt
+++ b/Documentation/printk-formats.txt
@@ -275,6 +275,42 @@ struct va_format:
Passed by reference.
+kobjects:
+ %pO
+
+ Base specifier for kobject based structs. Must be followed with
+ character for specific type of kobject as listed below:
+
+ Device tree nodes:
+
+ %pOF[fnpPcCF]
+
+ For printing device tree nodes. The optional arguments are:
+ f device node full_name
+ n device node name
+ p device node phandle
+ P device node path spec (name + @unit)
+ F device node flags
+ c major compatible string
+ C full compatible string
+ Without any arguments prints full_name (same as %pOFf)
+ The separator when using multiple arguments is ':'
+
+ Examples:
+
+ %pOF /foo/bar@0 - Node full name
+ %pOFf /foo/bar@0 - Same as above
+ %pOFfp /foo/bar@0:10 - Node full name + phandle
+ %pOFfcF /foo/bar@0:foo,device:--P- - Node full name +
+ major compatible string +
+ node flags
+ D - dynamic
+ d - detached
+ P - Populated
+ B - Populated bus
+
+ Passed by reference.
+
struct clk:
%pC pll1
diff --git a/Documentation/xtensa/mmu.txt b/Documentation/xtensa/mmu.txt
index 222a2c6748e6..5de8715d5bec 100644
--- a/Documentation/xtensa/mmu.txt
+++ b/Documentation/xtensa/mmu.txt
@@ -41,9 +41,9 @@ The scheme below assumes that the kernel is loaded below 0x40000000.
00..1F -> 00 -> 00 -> 00
The default location of IO peripherals is above 0xf0000000. This may be changed
-using a "ranges" property in a device tree simple-bus node. See ePAPR 1.1, §6.5
-for details on the syntax and semantic of simple-bus nodes. The following
-limitations apply:
+using a "ranges" property in a device tree simple-bus node. See the Devicetree
+Specification, section 4.5 for details on the syntax and semantics of
+simple-bus nodes. The following limitations apply:
1. Only top level simple-bus nodes are considered