diff options
Diffstat (limited to 'Documentation')
55 files changed, 1976 insertions, 1021 deletions
diff --git a/Documentation/ABI/testing/sysfs-memory-page-offline b/Documentation/ABI/testing/sysfs-memory-page-offline new file mode 100644 index 000000000000..e14703f12fdf --- /dev/null +++ b/Documentation/ABI/testing/sysfs-memory-page-offline @@ -0,0 +1,44 @@ +What: /sys/devices/system/memory/soft_offline_page +Date: Sep 2009 +KernelVersion: 2.6.33 +Contact: andi@firstfloor.org +Description: + Soft-offline the memory page containing the physical address + written into this file. Input is a hex number specifying the + physical address of the page. The kernel will then attempt + to soft-offline it, by moving the contents elsewhere or + dropping it if possible. The kernel will then be placed + on the bad page list and never be reused. + + The offlining is done in kernel specific granuality. + Normally it's the base page size of the kernel, but + this might change. + + The page must be still accessible, not poisoned. The + kernel will never kill anything for this, but rather + fail the offline. Return value is the size of the + number, or a error when the offlining failed. Reading + the file is not allowed. + +What: /sys/devices/system/memory/hard_offline_page +Date: Sep 2009 +KernelVersion: 2.6.33 +Contact: andi@firstfloor.org +Description: + Hard-offline the memory page containing the physical + address written into this file. Input is a hex number + specifying the physical address of the page. The + kernel will then attempt to hard-offline the page, by + trying to drop the page or killing any owner or + triggering IO errors if needed. Note this may kill + any processes owning the page. The kernel will avoid + to access this page assuming it's poisoned by the + hardware. + + The offlining is done in kernel specific granuality. + Normally it's the base page size of the kernel, but + this might change. + + Return value is the size of the number, or a error when + the offlining failed. + Reading the file is not allowed. diff --git a/Documentation/Changes b/Documentation/Changes index 6d0f1efc5bf6..f08b313cd235 100644 --- a/Documentation/Changes +++ b/Documentation/Changes @@ -49,6 +49,8 @@ o oprofile 0.9 # oprofiled --version o udev 081 # udevinfo -V o grub 0.93 # grub --version o mcelog 0.6 +o iptables 1.4.1 # iptables -V + Kernel compilation ================== diff --git a/Documentation/DocBook/Makefile b/Documentation/DocBook/Makefile index ab8300f67182..325cfd1d6d99 100644 --- a/Documentation/DocBook/Makefile +++ b/Documentation/DocBook/Makefile @@ -8,7 +8,7 @@ DOCBOOKS := z8530book.xml mcabook.xml device-drivers.xml \ kernel-hacking.xml kernel-locking.xml deviceiobook.xml \ - procfs-guide.xml writing_usb_driver.xml networking.xml \ + writing_usb_driver.xml networking.xml \ kernel-api.xml filesystems.xml lsm.xml usb.xml kgdb.xml \ gadget.xml libata.xml mtdnand.xml librs.xml rapidio.xml \ genericirq.xml s390-drivers.xml uio-howto.xml scsi.xml \ @@ -32,10 +32,10 @@ PS_METHOD = $(prefer-db2x) ### # The targets that may be used. -PHONY += xmldocs sgmldocs psdocs pdfdocs htmldocs mandocs installmandocs cleandocs media +PHONY += xmldocs sgmldocs psdocs pdfdocs htmldocs mandocs installmandocs cleandocs xmldoclinks BOOKS := $(addprefix $(obj)/,$(DOCBOOKS)) -xmldocs: $(BOOKS) +xmldocs: $(BOOKS) xmldoclinks sgmldocs: xmldocs PS := $(patsubst %.xml, %.ps, $(BOOKS)) @@ -45,15 +45,24 @@ PDF := $(patsubst %.xml, %.pdf, $(BOOKS)) pdfdocs: $(PDF) HTML := $(sort $(patsubst %.xml, %.html, $(BOOKS))) -htmldocs: media $(HTML) +htmldocs: $(HTML) $(call build_main_index) + $(call build_images) MAN := $(patsubst %.xml, %.9, $(BOOKS)) mandocs: $(MAN) -media: - mkdir -p $(srctree)/Documentation/DocBook/media/ - cp $(srctree)/Documentation/DocBook/dvb/*.png $(srctree)/Documentation/DocBook/v4l/*.gif $(srctree)/Documentation/DocBook/media/ +build_images = mkdir -p $(objtree)/Documentation/DocBook/media/ && \ + cp $(srctree)/Documentation/DocBook/dvb/*.png $(srctree)/Documentation/DocBook/v4l/*.gif $(objtree)/Documentation/DocBook/media/ + +xmldoclinks: +ifneq ($(objtree),$(srctree)) + for dep in dvb media-entities.tmpl media-indices.tmpl v4l; do \ + rm -f $(objtree)/Documentation/DocBook/$$dep \ + && ln -s $(srctree)/Documentation/DocBook/$$dep $(objtree)/Documentation/DocBook/ \ + || exit; \ + done +endif installmandocs: mandocs mkdir -p /usr/local/man/man9/ @@ -65,7 +74,7 @@ KERNELDOC = $(srctree)/scripts/kernel-doc DOCPROC = $(objtree)/scripts/basic/docproc XMLTOFLAGS = -m $(srctree)/Documentation/DocBook/stylesheet.xsl -#XMLTOFLAGS += --skip-validation +XMLTOFLAGS += --skip-validation ### # DOCPROC is used for two purposes: @@ -101,17 +110,6 @@ endif # Changes in kernel-doc force a rebuild of all documentation $(BOOKS): $(KERNELDOC) -### -# procfs guide uses a .c file as example code. -# This requires an explicit dependency -C-procfs-example = procfs_example.xml -C-procfs-example2 = $(addprefix $(obj)/,$(C-procfs-example)) -$(obj)/procfs-guide.xml: $(C-procfs-example2) - -# List of programs to build -##oops, this is a kernel module::hostprogs-y := procfs_example -obj-m += procfs_example.o - # Tell kbuild to always build the programs always := $(hostprogs-y) @@ -238,7 +236,7 @@ clean-files := $(DOCBOOKS) \ $(patsubst %.xml, %.pdf, $(DOCBOOKS)) \ $(patsubst %.xml, %.html, $(DOCBOOKS)) \ $(patsubst %.xml, %.9, $(DOCBOOKS)) \ - $(C-procfs-example) $(index) + $(index) clean-dirs := $(patsubst %.xml,%,$(DOCBOOKS)) man diff --git a/Documentation/DocBook/media-entities.tmpl b/Documentation/DocBook/media-entities.tmpl index bb5ab741220e..c725cb852c54 100644 --- a/Documentation/DocBook/media-entities.tmpl +++ b/Documentation/DocBook/media-entities.tmpl @@ -23,6 +23,7 @@ <!ENTITY VIDIOC-ENUMINPUT "<link linkend='vidioc-enuminput'><constant>VIDIOC_ENUMINPUT</constant></link>"> <!ENTITY VIDIOC-ENUMOUTPUT "<link linkend='vidioc-enumoutput'><constant>VIDIOC_ENUMOUTPUT</constant></link>"> <!ENTITY VIDIOC-ENUMSTD "<link linkend='vidioc-enumstd'><constant>VIDIOC_ENUMSTD</constant></link>"> +<!ENTITY VIDIOC-ENUM-DV-PRESETS "<link linkend='vidioc-enum-dv-presets'><constant>VIDIOC_ENUM_DV_PRESETS</constant></link>"> <!ENTITY VIDIOC-ENUM-FMT "<link linkend='vidioc-enum-fmt'><constant>VIDIOC_ENUM_FMT</constant></link>"> <!ENTITY VIDIOC-ENUM-FRAMEINTERVALS "<link linkend='vidioc-enum-frameintervals'><constant>VIDIOC_ENUM_FRAMEINTERVALS</constant></link>"> <!ENTITY VIDIOC-ENUM-FRAMESIZES "<link linkend='vidioc-enum-framesizes'><constant>VIDIOC_ENUM_FRAMESIZES</constant></link>"> @@ -30,6 +31,8 @@ <!ENTITY VIDIOC-G-AUDOUT "<link linkend='vidioc-g-audioout'><constant>VIDIOC_G_AUDOUT</constant></link>"> <!ENTITY VIDIOC-G-CROP "<link linkend='vidioc-g-crop'><constant>VIDIOC_G_CROP</constant></link>"> <!ENTITY VIDIOC-G-CTRL "<link linkend='vidioc-g-ctrl'><constant>VIDIOC_G_CTRL</constant></link>"> +<!ENTITY VIDIOC-G-DV-PRESET "<link linkend='vidioc-g-dv-preset'><constant>VIDIOC_G_DV_PRESET</constant></link>"> +<!ENTITY VIDIOC-G-DV-TIMINGS "<link linkend='vidioc-g-dv-timings'><constant>VIDIOC_G_DV_TIMINGS</constant></link>"> <!ENTITY VIDIOC-G-ENC-INDEX "<link linkend='vidioc-g-enc-index'><constant>VIDIOC_G_ENC_INDEX</constant></link>"> <!ENTITY VIDIOC-G-EXT-CTRLS "<link linkend='vidioc-g-ext-ctrls'><constant>VIDIOC_G_EXT_CTRLS</constant></link>"> <!ENTITY VIDIOC-G-FBUF "<link linkend='vidioc-g-fbuf'><constant>VIDIOC_G_FBUF</constant></link>"> @@ -53,6 +56,7 @@ <!ENTITY VIDIOC-QUERYCTRL "<link linkend='vidioc-queryctrl'><constant>VIDIOC_QUERYCTRL</constant></link>"> <!ENTITY VIDIOC-QUERYMENU "<link linkend='vidioc-queryctrl'><constant>VIDIOC_QUERYMENU</constant></link>"> <!ENTITY VIDIOC-QUERYSTD "<link linkend='vidioc-querystd'><constant>VIDIOC_QUERYSTD</constant></link>"> +<!ENTITY VIDIOC-QUERY-DV-PRESET "<link linkend='vidioc-query-dv-preset'><constant>VIDIOC_QUERY_DV_PRESET</constant></link>"> <!ENTITY VIDIOC-REQBUFS "<link linkend='vidioc-reqbufs'><constant>VIDIOC_REQBUFS</constant></link>"> <!ENTITY VIDIOC-STREAMOFF "<link linkend='vidioc-streamon'><constant>VIDIOC_STREAMOFF</constant></link>"> <!ENTITY VIDIOC-STREAMON "<link linkend='vidioc-streamon'><constant>VIDIOC_STREAMON</constant></link>"> @@ -60,6 +64,8 @@ <!ENTITY VIDIOC-S-AUDOUT "<link linkend='vidioc-g-audioout'><constant>VIDIOC_S_AUDOUT</constant></link>"> <!ENTITY VIDIOC-S-CROP "<link linkend='vidioc-g-crop'><constant>VIDIOC_S_CROP</constant></link>"> <!ENTITY VIDIOC-S-CTRL "<link linkend='vidioc-g-ctrl'><constant>VIDIOC_S_CTRL</constant></link>"> +<!ENTITY VIDIOC-S-DV-PRESET "<link linkend='vidioc-g-dv-preset'><constant>VIDIOC_S_DV_PRESET</constant></link>"> +<!ENTITY VIDIOC-S-DV-TIMINGS "<link linkend='vidioc-g-dv-timings'><constant>VIDIOC_S_DV_TIMINGS</constant></link>"> <!ENTITY VIDIOC-S-EXT-CTRLS "<link linkend='vidioc-g-ext-ctrls'><constant>VIDIOC_S_EXT_CTRLS</constant></link>"> <!ENTITY VIDIOC-S-FBUF "<link linkend='vidioc-g-fbuf'><constant>VIDIOC_S_FBUF</constant></link>"> <!ENTITY VIDIOC-S-FMT "<link linkend='vidioc-g-fmt'><constant>VIDIOC_S_FMT</constant></link>"> @@ -118,6 +124,7 @@ <!-- Structures --> <!ENTITY v4l2-audio "struct <link linkend='v4l2-audio'>v4l2_audio</link>"> <!ENTITY v4l2-audioout "struct <link linkend='v4l2-audioout'>v4l2_audioout</link>"> +<!ENTITY v4l2-bt-timings "struct <link linkend='v4l2-bt-timings'>v4l2_bt_timings</link>"> <!ENTITY v4l2-buffer "struct <link linkend='v4l2-buffer'>v4l2_buffer</link>"> <!ENTITY v4l2-capability "struct <link linkend='v4l2-capability'>v4l2_capability</link>"> <!ENTITY v4l2-captureparm "struct <link linkend='v4l2-captureparm'>v4l2_captureparm</link>"> @@ -128,6 +135,9 @@ <!ENTITY v4l2-dbg-chip-ident "struct <link linkend='v4l2-dbg-chip-ident'>v4l2_dbg_chip_ident</link>"> <!ENTITY v4l2-dbg-match "struct <link linkend='v4l2-dbg-match'>v4l2_dbg_match</link>"> <!ENTITY v4l2-dbg-register "struct <link linkend='v4l2-dbg-register'>v4l2_dbg_register</link>"> +<!ENTITY v4l2-dv-enum-preset "struct <link linkend='v4l2-dv-enum-preset'>v4l2_dv_enum_preset</link>"> +<!ENTITY v4l2-dv-preset "struct <link linkend='v4l2-dv-preset'>v4l2_dv_preset</link>"> +<!ENTITY v4l2-dv-timings "struct <link linkend='v4l2-dv-timings'>v4l2_dv_timings</link>"> <!ENTITY v4l2-enc-idx "struct <link linkend='v4l2-enc-idx'>v4l2_enc_idx</link>"> <!ENTITY v4l2-enc-idx-entry "struct <link linkend='v4l2-enc-idx-entry'>v4l2_enc_idx_entry</link>"> <!ENTITY v4l2-encoder-cmd "struct <link linkend='v4l2-encoder-cmd'>v4l2_encoder_cmd</link>"> @@ -243,6 +253,10 @@ <!ENTITY sub-enumaudioout SYSTEM "v4l/vidioc-enumaudioout.xml"> <!ENTITY sub-enuminput SYSTEM "v4l/vidioc-enuminput.xml"> <!ENTITY sub-enumoutput SYSTEM "v4l/vidioc-enumoutput.xml"> +<!ENTITY sub-enum-dv-presets SYSTEM "v4l/vidioc-enum-dv-presets.xml"> +<!ENTITY sub-g-dv-preset SYSTEM "v4l/vidioc-g-dv-preset.xml"> +<!ENTITY sub-query-dv-preset SYSTEM "v4l/vidioc-query-dv-preset.xml"> +<!ENTITY sub-g-dv-timings SYSTEM "v4l/vidioc-g-dv-timings.xml"> <!ENTITY sub-enumstd SYSTEM "v4l/vidioc-enumstd.xml"> <!ENTITY sub-g-audio SYSTEM "v4l/vidioc-g-audio.xml"> <!ENTITY sub-g-audioout SYSTEM "v4l/vidioc-g-audioout.xml"> @@ -333,6 +347,10 @@ <!ENTITY enumaudioout SYSTEM "v4l/vidioc-enumaudioout.xml"> <!ENTITY enuminput SYSTEM "v4l/vidioc-enuminput.xml"> <!ENTITY enumoutput SYSTEM "v4l/vidioc-enumoutput.xml"> +<!ENTITY enum-dv-presets SYSTEM "v4l/vidioc-enum-dv-presets.xml"> +<!ENTITY g-dv-preset SYSTEM "v4l/vidioc-g-dv-preset.xml"> +<!ENTITY query-dv-preset SYSTEM "v4l/vidioc-query-dv-preset.xml"> +<!ENTITY g-dv-timings SYSTEM "v4l/vidioc-g-dv-timings.xml"> <!ENTITY enumstd SYSTEM "v4l/vidioc-enumstd.xml"> <!ENTITY g-audio SYSTEM "v4l/vidioc-g-audio.xml"> <!ENTITY g-audioout SYSTEM "v4l/vidioc-g-audioout.xml"> diff --git a/Documentation/DocBook/media-indices.tmpl b/Documentation/DocBook/media-indices.tmpl index 9e30a236d74f..78d6031de001 100644 --- a/Documentation/DocBook/media-indices.tmpl +++ b/Documentation/DocBook/media-indices.tmpl @@ -36,6 +36,7 @@ <indexentry><primaryie>enum <link linkend='v4l2-preemphasis'>v4l2_preemphasis</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-audio'>v4l2_audio</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-audioout'>v4l2_audioout</link></primaryie></indexentry> +<indexentry><primaryie>struct <link linkend='v4l2-bt-timings'>v4l2_bt_timings</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-buffer'>v4l2_buffer</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-capability'>v4l2_capability</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-captureparm'>v4l2_captureparm</link></primaryie></indexentry> @@ -46,6 +47,9 @@ <indexentry><primaryie>struct <link linkend='v4l2-dbg-chip-ident'>v4l2_dbg_chip_ident</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-dbg-match'>v4l2_dbg_match</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-dbg-register'>v4l2_dbg_register</link></primaryie></indexentry> +<indexentry><primaryie>struct <link linkend='v4l2-dv-enum-preset'>v4l2_dv_enum_preset</link></primaryie></indexentry> +<indexentry><primaryie>struct <link linkend='v4l2-dv-preset'>v4l2_dv_preset</link></primaryie></indexentry> +<indexentry><primaryie>struct <link linkend='v4l2-dv-timings'>v4l2_dv_timings</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-enc-idx'>v4l2_enc_idx</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-enc-idx-entry'>v4l2_enc_idx_entry</link></primaryie></indexentry> <indexentry><primaryie>struct <link linkend='v4l2-encoder-cmd'>v4l2_encoder_cmd</link></primaryie></indexentry> diff --git a/Documentation/DocBook/procfs-guide.tmpl b/Documentation/DocBook/procfs-guide.tmpl deleted file mode 100644 index 9eba4b7af73d..000000000000 --- a/Documentation/DocBook/procfs-guide.tmpl +++ /dev/null @@ -1,626 +0,0 @@ -<?xml version="1.0" encoding="UTF-8"?> -<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.1.2//EN" - "http://www.oasis-open.org/docbook/xml/4.1.2/docbookx.dtd" [ -<!ENTITY procfsexample SYSTEM "procfs_example.xml"> -]> - -<book id="LKProcfsGuide"> - <bookinfo> - <title>Linux Kernel Procfs Guide</title> - - <authorgroup> - <author> - <firstname>Erik</firstname> - <othername>(J.A.K.)</othername> - <surname>Mouw</surname> - <affiliation> - <address> - <email>mouw@nl.linux.org</email> - </address> - </affiliation> - </author> - <othercredit> - <contrib> - This software and documentation were written while working on the - LART computing board - (<ulink url="http://www.lartmaker.nl/">http://www.lartmaker.nl/</ulink>), - which was sponsored by the Delt University of Technology projects - Mobile Multi-media Communications and Ubiquitous Communications. - </contrib> - </othercredit> - </authorgroup> - - <revhistory> - <revision> - <revnumber>1.0</revnumber> - <date>May 30, 2001</date> - <revremark>Initial revision posted to linux-kernel</revremark> - </revision> - <revision> - <revnumber>1.1</revnumber> - <date>June 3, 2001</date> - <revremark>Revised after comments from linux-kernel</revremark> - </revision> - </revhistory> - - <copyright> - <year>2001</year> - <holder>Erik Mouw</holder> - </copyright> - - - <legalnotice> - <para> - This documentation is free software; you can redistribute it - and/or modify it under the terms of the GNU General Public - License as published by the Free Software Foundation; either - version 2 of the License, or (at your option) any later - version. - </para> - - <para> - This documentation is distributed in the hope that it will be - useful, but WITHOUT ANY WARRANTY; without even the implied - warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR - PURPOSE. See the GNU General Public License for more details. - </para> - - <para> - You should have received a copy of the GNU General Public - License along with this program; if not, write to the Free - Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, - MA 02111-1307 USA - </para> - - <para> - For more details see the file COPYING in the source - distribution of Linux. - </para> - </legalnotice> - </bookinfo> - - - - - <toc> - </toc> - - - - - <preface id="Preface"> - <title>Preface</title> - - <para> - This guide describes the use of the procfs file system from - within the Linux kernel. The idea to write this guide came up on - the #kernelnewbies IRC channel (see <ulink - url="http://www.kernelnewbies.org/">http://www.kernelnewbies.org/</ulink>), - when Jeff Garzik explained the use of procfs and forwarded me a - message Alexander Viro wrote to the linux-kernel mailing list. I - agreed to write it up nicely, so here it is. - </para> - - <para> - I'd like to thank Jeff Garzik - <email>jgarzik@pobox.com</email> and Alexander Viro - <email>viro@parcelfarce.linux.theplanet.co.uk</email> for their input, - Tim Waugh <email>twaugh@redhat.com</email> for his <ulink - url="http://people.redhat.com/twaugh/docbook/selfdocbook/">Selfdocbook</ulink>, - and Marc Joosen <email>marcj@historia.et.tudelft.nl</email> for - proofreading. - </para> - - <para> - Erik - </para> - </preface> - - - - - <chapter id="intro"> - <title>Introduction</title> - - <para> - The <filename class="directory">/proc</filename> file system - (procfs) is a special file system in the linux kernel. It's a - virtual file system: it is not associated with a block device - but exists only in memory. The files in the procfs are there to - allow userland programs access to certain information from the - kernel (like process information in <filename - class="directory">/proc/[0-9]+/</filename>), but also for debug - purposes (like <filename>/proc/ksyms</filename>). - </para> - - <para> - This guide describes the use of the procfs file system from - within the Linux kernel. It starts by introducing all relevant - functions to manage the files within the file system. After that - it shows how to communicate with userland, and some tips and - tricks will be pointed out. Finally a complete example will be - shown. - </para> - - <para> - Note that the files in <filename - class="directory">/proc/sys</filename> are sysctl files: they - don't belong to procfs and are governed by a completely - different API described in the Kernel API book. - </para> - </chapter> - - - - - <chapter id="managing"> - <title>Managing procfs entries</title> - - <para> - This chapter describes the functions that various kernel - components use to populate the procfs with files, symlinks, - device nodes, and directories. - </para> - - <para> - A minor note before we start: if you want to use any of the - procfs functions, be sure to include the correct header file! - This should be one of the first lines in your code: - </para> - - <programlisting> -#include <linux/proc_fs.h> - </programlisting> - - - - - <sect1 id="regularfile"> - <title>Creating a regular file</title> - - <funcsynopsis> - <funcprototype> - <funcdef>struct proc_dir_entry* <function>create_proc_entry</function></funcdef> - <paramdef>const char* <parameter>name</parameter></paramdef> - <paramdef>mode_t <parameter>mode</parameter></paramdef> - <paramdef>struct proc_dir_entry* <parameter>parent</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - This function creates a regular file with the name - <parameter>name</parameter>, file mode - <parameter>mode</parameter> in the directory - <parameter>parent</parameter>. To create a file in the root of - the procfs, use <constant>NULL</constant> as - <parameter>parent</parameter> parameter. When successful, the - function will return a pointer to the freshly created - <structname>struct proc_dir_entry</structname>; otherwise it - will return <constant>NULL</constant>. <xref - linkend="userland"/> describes how to do something useful with - regular files. - </para> - - <para> - Note that it is specifically supported that you can pass a - path that spans multiple directories. For example - <function>create_proc_entry</function>(<parameter>"drivers/via0/info"</parameter>) - will create the <filename class="directory">via0</filename> - directory if necessary, with standard - <constant>0755</constant> permissions. - </para> - - <para> - If you only want to be able to read the file, the function - <function>create_proc_read_entry</function> described in <xref - linkend="convenience"/> may be used to create and initialise - the procfs entry in one single call. - </para> - </sect1> - - - - - <sect1 id="Creating_a_symlink"> - <title>Creating a symlink</title> - - <funcsynopsis> - <funcprototype> - <funcdef>struct proc_dir_entry* - <function>proc_symlink</function></funcdef> <paramdef>const - char* <parameter>name</parameter></paramdef> - <paramdef>struct proc_dir_entry* - <parameter>parent</parameter></paramdef> <paramdef>const - char* <parameter>dest</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - This creates a symlink in the procfs directory - <parameter>parent</parameter> that points from - <parameter>name</parameter> to - <parameter>dest</parameter>. This translates in userland to - <literal>ln -s</literal> <parameter>dest</parameter> - <parameter>name</parameter>. - </para> - </sect1> - - <sect1 id="Creating_a_directory"> - <title>Creating a directory</title> - - <funcsynopsis> - <funcprototype> - <funcdef>struct proc_dir_entry* <function>proc_mkdir</function></funcdef> - <paramdef>const char* <parameter>name</parameter></paramdef> - <paramdef>struct proc_dir_entry* <parameter>parent</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - Create a directory <parameter>name</parameter> in the procfs - directory <parameter>parent</parameter>. - </para> - </sect1> - - - - - <sect1 id="Removing_an_entry"> - <title>Removing an entry</title> - - <funcsynopsis> - <funcprototype> - <funcdef>void <function>remove_proc_entry</function></funcdef> - <paramdef>const char* <parameter>name</parameter></paramdef> - <paramdef>struct proc_dir_entry* <parameter>parent</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - Removes the entry <parameter>name</parameter> in the directory - <parameter>parent</parameter> from the procfs. Entries are - removed by their <emphasis>name</emphasis>, not by the - <structname>struct proc_dir_entry</structname> returned by the - various create functions. Note that this function doesn't - recursively remove entries. - </para> - - <para> - Be sure to free the <structfield>data</structfield> entry from - the <structname>struct proc_dir_entry</structname> before - <function>remove_proc_entry</function> is called (that is: if - there was some <structfield>data</structfield> allocated, of - course). See <xref linkend="usingdata"/> for more information - on using the <structfield>data</structfield> entry. - </para> - </sect1> - </chapter> - - - - - <chapter id="userland"> - <title>Communicating with userland</title> - - <para> - Instead of reading (or writing) information directly from - kernel memory, procfs works with <emphasis>call back - functions</emphasis> for files: functions that are called when - a specific file is being read or written. Such functions have - to be initialised after the procfs file is created by setting - the <structfield>read_proc</structfield> and/or - <structfield>write_proc</structfield> fields in the - <structname>struct proc_dir_entry*</structname> that the - function <function>create_proc_entry</function> returned: - </para> - - <programlisting> -struct proc_dir_entry* entry; - -entry->read_proc = read_proc_foo; -entry->write_proc = write_proc_foo; - </programlisting> - - <para> - If you only want to use a the - <structfield>read_proc</structfield>, the function - <function>create_proc_read_entry</function> described in <xref - linkend="convenience"/> may be used to create and initialise the - procfs entry in one single call. - </para> - - - - <sect1 id="Reading_data"> - <title>Reading data</title> - - <para> - The read function is a call back function that allows userland - processes to read data from the kernel. The read function - should have the following format: - </para> - - <funcsynopsis> - <funcprototype> - <funcdef>int <function>read_func</function></funcdef> - <paramdef>char* <parameter>buffer</parameter></paramdef> - <paramdef>char** <parameter>start</parameter></paramdef> - <paramdef>off_t <parameter>off</parameter></paramdef> - <paramdef>int <parameter>count</parameter></paramdef> - <paramdef>int* <parameter>peof</parameter></paramdef> - <paramdef>void* <parameter>data</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - The read function should write its information into the - <parameter>buffer</parameter>, which will be exactly - <literal>PAGE_SIZE</literal> bytes long. - </para> - - <para> - The parameter - <parameter>peof</parameter> should be used to signal that the - end of the file has been reached by writing - <literal>1</literal> to the memory location - <parameter>peof</parameter> points to. - </para> - - <para> - The <parameter>data</parameter> - parameter can be used to create a single call back function for - several files, see <xref linkend="usingdata"/>. - </para> - - <para> - The rest of the parameters and the return value are described - by a comment in <filename>fs/proc/generic.c</filename> as follows: - </para> - - <blockquote> - <para> - You have three ways to return data: - </para> - <orderedlist> - <listitem> - <para> - Leave <literal>*start = NULL</literal>. (This is the default.) - Put the data of the requested offset at that - offset within the buffer. Return the number (<literal>n</literal>) - of bytes there are from the beginning of the - buffer up to the last byte of data. If the - number of supplied bytes (<literal>= n - offset</literal>) is - greater than zero and you didn't signal eof - and the reader is prepared to take more data - you will be called again with the requested - offset advanced by the number of bytes - absorbed. This interface is useful for files - no larger than the buffer. - </para> - </listitem> - <listitem> - <para> - Set <literal>*start</literal> to an unsigned long value less than - the buffer address but greater than zero. - Put the data of the requested offset at the - beginning of the buffer. Return the number of - bytes of data placed there. If this number is - greater than zero and you didn't signal eof - and the reader is prepared to take more data - you will be called again with the requested - offset advanced by <literal>*start</literal>. This interface is - useful when you have a large file consisting - of a series of blocks which you want to count - and return as wholes. - (Hack by Paul.Russell@rustcorp.com.au) - </para> - </listitem> - <listitem> - <para> - Set <literal>*start</literal> to an address within the buffer. - Put the data of the requested offset at <literal>*start</literal>. - Return the number of bytes of data placed there. - If this number is greater than zero and you - didn't signal eof and the reader is prepared to - take more data you will be called again with the - requested offset advanced by the number of bytes - absorbed. - </para> - </listitem> - </orderedlist> - </blockquote> - - <para> - <xref linkend="example"/> shows how to use a read call back - function. - </para> - </sect1> - - - - - <sect1 id="Writing_data"> - <title>Writing data</title> - - <para> - The write call back function allows a userland process to write - data to the kernel, so it has some kind of control over the - kernel. The write function should have the following format: - </para> - - <funcsynopsis> - <funcprototype> - <funcdef>int <function>write_func</function></funcdef> - <paramdef>struct file* <parameter>file</parameter></paramdef> - <paramdef>const char* <parameter>buffer</parameter></paramdef> - <paramdef>unsigned long <parameter>count</parameter></paramdef> - <paramdef>void* <parameter>data</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - The write function should read <parameter>count</parameter> - bytes at maximum from the <parameter>buffer</parameter>. Note - that the <parameter>buffer</parameter> doesn't live in the - kernel's memory space, so it should first be copied to kernel - space with <function>copy_from_user</function>. The - <parameter>file</parameter> parameter is usually - ignored. <xref linkend="usingdata"/> shows how to use the - <parameter>data</parameter> parameter. - </para> - - <para> - Again, <xref linkend="example"/> shows how to use this call back - function. - </para> - </sect1> - - - - - <sect1 id="usingdata"> - <title>A single call back for many files</title> - - <para> - When a large number of almost identical files is used, it's - quite inconvenient to use a separate call back function for - each file. A better approach is to have a single call back - function that distinguishes between the files by using the - <structfield>data</structfield> field in <structname>struct - proc_dir_entry</structname>. First of all, the - <structfield>data</structfield> field has to be initialised: - </para> - - <programlisting> -struct proc_dir_entry* entry; -struct my_file_data *file_data; - -file_data = kmalloc(sizeof(struct my_file_data), GFP_KERNEL); -entry->data = file_data; - </programlisting> - - <para> - The <structfield>data</structfield> field is a <type>void - *</type>, so it can be initialised with anything. - </para> - - <para> - Now that the <structfield>data</structfield> field is set, the - <function>read_proc</function> and - <function>write_proc</function> can use it to distinguish - between files because they get it passed into their - <parameter>data</parameter> parameter: - </para> - - <programlisting> -int foo_read_func(char *page, char **start, off_t off, - int count, int *eof, void *data) -{ - int len; - - if(data == file_data) { - /* special case for this file */ - } else { - /* normal processing */ - } - - return len; -} - </programlisting> - - <para> - Be sure to free the <structfield>data</structfield> data field - when removing the procfs entry. - </para> - </sect1> - </chapter> - - - - - <chapter id="tips"> - <title>Tips and tricks</title> - - - - - <sect1 id="convenience"> - <title>Convenience functions</title> - - <funcsynopsis> - <funcprototype> - <funcdef>struct proc_dir_entry* <function>create_proc_read_entry</function></funcdef> - <paramdef>const char* <parameter>name</parameter></paramdef> - <paramdef>mode_t <parameter>mode</parameter></paramdef> - <paramdef>struct proc_dir_entry* <parameter>parent</parameter></paramdef> - <paramdef>read_proc_t* <parameter>read_proc</parameter></paramdef> - <paramdef>void* <parameter>data</parameter></paramdef> - </funcprototype> - </funcsynopsis> - - <para> - This function creates a regular file in exactly the same way - as <function>create_proc_entry</function> from <xref - linkend="regularfile"/> does, but also allows to set the read - function <parameter>read_proc</parameter> in one call. This - function can set the <parameter>data</parameter> as well, like - explained in <xref linkend="usingdata"/>. - </para> - </sect1> - - - - <sect1 id="Modules"> - <title>Modules</title> - - <para> - If procfs is being used from within a module, be sure to set - the <structfield>owner</structfield> field in the - <structname>struct proc_dir_entry</structname> to - <constant>THIS_MODULE</constant>. - </para> - - <programlisting> -struct proc_dir_entry* entry; - -entry->owner = THIS_MODULE; - </programlisting> - </sect1> - - - - - <sect1 id="Mode_and_ownership"> - <title>Mode and ownership</title> - - <para> - Sometimes it is useful to change the mode and/or ownership of - a procfs entry. Here is an example that shows how to achieve - that: - </para> - - <programlisting> -struct proc_dir_entry* entry; - -entry->mode = S_IWUSR |S_IRUSR | S_IRGRP | S_IROTH; -entry->uid = 0; -entry->gid = 100; - </programlisting> - - </sect1> - </chapter> - - - - - <chapter id="example"> - <title>Example</title> - - <!-- be careful with the example code: it shouldn't be wider than - approx. 60 columns, or otherwise it won't fit properly on a page - --> - -&procfsexample; - - </chapter> -</book> diff --git a/Documentation/DocBook/procfs_example.c b/Documentation/DocBook/procfs_example.c deleted file mode 100644 index a5b11793b1e0..000000000000 --- a/Documentation/DocBook/procfs_example.c +++ /dev/null @@ -1,201 +0,0 @@ -/* - * procfs_example.c: an example proc interface - * - * Copyright (C) 2001, Erik Mouw (mouw@nl.linux.org) - * - * This file accompanies the procfs-guide in the Linux kernel - * source. Its main use is to demonstrate the concepts and - * functions described in the guide. - * - * This software has been developed while working on the LART - * computing board (http://www.lartmaker.nl), which was sponsored - * by the Delt University of Technology projects Mobile Multi-media - * Communications and Ubiquitous Communications. - * - * This program is free software; you can redistribute - * it and/or modify it under the terms of the GNU General - * Public License as published by the Free Software - * Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * This program is distributed in the hope that it will be - * useful, but WITHOUT ANY WARRANTY; without even the implied - * warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR - * PURPOSE. See the GNU General Public License for more - * details. - * - * You should have received a copy of the GNU General Public - * License along with this program; if not, write to the - * Free Software Foundation, Inc., 59 Temple Place, - * Suite 330, Boston, MA 02111-1307 USA - * - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/proc_fs.h> -#include <linux/jiffies.h> -#include <asm/uaccess.h> - - -#define MODULE_VERS "1.0" -#define MODULE_NAME "procfs_example" - -#define FOOBAR_LEN 8 - -struct fb_data_t { - char name[FOOBAR_LEN + 1]; - char value[FOOBAR_LEN + 1]; -}; - - -static struct proc_dir_entry *example_dir, *foo_file, - *bar_file, *jiffies_file, *symlink; - - -struct fb_data_t foo_data, bar_data; - - -static int proc_read_jiffies(char *page, char **start, - off_t off, int count, - int *eof, void *data) -{ - int len; - - len = sprintf(page, "jiffies = %ld\n", - jiffies); - - return len; -} - - -static int proc_read_foobar(char *page, char **start, - off_t off, int count, - int *eof, void *data) -{ - int len; - struct fb_data_t *fb_data = (struct fb_data_t *)data; - - /* DON'T DO THAT - buffer overruns are bad */ - len = sprintf(page, "%s = '%s'\n", - fb_data->name, fb_data->value); - - return len; -} - - -static int proc_write_foobar(struct file *file, - const char *buffer, - unsigned long count, - void *data) -{ - int len; - struct fb_data_t *fb_data = (struct fb_data_t *)data; - - if(count > FOOBAR_LEN) - len = FOOBAR_LEN; - else - len = count; - - if(copy_from_user(fb_data->value, buffer, len)) - return -EFAULT; - - fb_data->value[len] = '\0'; - - return len; -} - - -static int __init init_procfs_example(void) -{ - int rv = 0; - - /* create directory */ - example_dir = proc_mkdir(MODULE_NAME, NULL); - if(example_dir == NULL) { - rv = -ENOMEM; - goto out; - } - /* create jiffies using convenience function */ - jiffies_file = create_proc_read_entry("jiffies", - 0444, example_dir, - proc_read_jiffies, - NULL); - if(jiffies_file == NULL) { - rv = -ENOMEM; - goto no_jiffies; - } - - /* create foo and bar files using same callback - * functions - */ - foo_file = create_proc_entry("foo", 0644, example_dir); - if(foo_file == NULL) { - rv = -ENOMEM; - goto no_foo; - } - - strcpy(foo_data.name, "foo"); - strcpy(foo_data.value, "foo"); - foo_file->data = &foo_data; - foo_file->read_proc = proc_read_foobar; - foo_file->write_proc = proc_write_foobar; - - bar_file = create_proc_entry("bar", 0644, example_dir); - if(bar_file == NULL) { - rv = -ENOMEM; - goto no_bar; - } - - strcpy(bar_data.name, "bar"); - strcpy(bar_data.value, "bar"); - bar_file->data = &bar_data; - bar_file->read_proc = proc_read_foobar; - bar_file->write_proc = proc_write_foobar; - - /* create symlink */ - symlink = proc_symlink("jiffies_too", example_dir, - "jiffies"); - if(symlink == NULL) { - rv = -ENOMEM; - goto no_symlink; - } - - /* everything OK */ - printk(KERN_INFO "%s %s initialised\n", - MODULE_NAME, MODULE_VERS); - return 0; - -no_symlink: - remove_proc_entry("bar", example_dir); -no_bar: - remove_proc_entry("foo", example_dir); -no_foo: - remove_proc_entry("jiffies", example_dir); -no_jiffies: - remove_proc_entry(MODULE_NAME, NULL); -out: - return rv; -} - - -static void __exit cleanup_procfs_example(void) -{ - remove_proc_entry("jiffies_too", example_dir); - remove_proc_entry("bar", example_dir); - remove_proc_entry("foo", example_dir); - remove_proc_entry("jiffies", example_dir); - remove_proc_entry(MODULE_NAME, NULL); - - printk(KERN_INFO "%s %s removed\n", - MODULE_NAME, MODULE_VERS); -} - - -module_init(init_procfs_example); -module_exit(cleanup_procfs_example); - -MODULE_AUTHOR("Erik Mouw"); -MODULE_DESCRIPTION("procfs examples"); -MODULE_LICENSE("GPL"); diff --git a/Documentation/DocBook/v4l/common.xml b/Documentation/DocBook/v4l/common.xml index b1a81d246d58..c65f0ac9b6ee 100644 --- a/Documentation/DocBook/v4l/common.xml +++ b/Documentation/DocBook/v4l/common.xml @@ -716,6 +716,41 @@ if (-1 == ioctl (fd, &VIDIOC-S-STD;, &std_id)) { } </programlisting> </example> + <section id="dv-timings"> + <title>Digital Video (DV) Timings</title> + <para> + The video standards discussed so far has been dealing with Analog TV and the +corresponding video timings. Today there are many more different hardware interfaces +such as High Definition TV interfaces (HDMI), VGA, DVI connectors etc., that carry +video signals and there is a need to extend the API to select the video timings +for these interfaces. Since it is not possible to extend the &v4l2-std-id; due to +the limited bits available, a new set of IOCTLs is added to set/get video timings at +the input and output: </para><itemizedlist> + <listitem> + <para>DV Presets: Digital Video (DV) presets. These are IDs representing a +video timing at the input/output. Presets are pre-defined timings implemented +by the hardware according to video standards. A __u32 data type is used to represent +a preset unlike the bit mask that is used in &v4l2-std-id; allowing future extensions +to support as many different presets as needed.</para> + </listitem> + <listitem> + <para>Custom DV Timings: This will allow applications to define more detailed +custom video timings for the interface. This includes parameters such as width, height, +polarities, frontporch, backporch etc. + </para> + </listitem> + </itemizedlist> + <para>To enumerate and query the attributes of DV presets supported by a device, +applications use the &VIDIOC-ENUM-DV-PRESETS; ioctl. To get the current DV preset, +applications use the &VIDIOC-G-DV-PRESET; ioctl and to set a preset they use the +&VIDIOC-S-DV-PRESET; ioctl.</para> + <para>To set custom DV timings for the device, applications use the +&VIDIOC-S-DV-TIMINGS; ioctl and to get current custom DV timings they use the +&VIDIOC-G-DV-TIMINGS; ioctl.</para> + <para>Applications can make use of the <xref linkend="input-capabilities" /> and +<xref linkend="output-capabilities"/> flags to decide what ioctls are available to set the +video timings for the device.</para> + </section> </section> &sub-controls; diff --git a/Documentation/DocBook/v4l/compat.xml b/Documentation/DocBook/v4l/compat.xml index 4d1902a54d61..b9dbdf9e6d29 100644 --- a/Documentation/DocBook/v4l/compat.xml +++ b/Documentation/DocBook/v4l/compat.xml @@ -2291,8 +2291,8 @@ was renamed to <structname id="v4l2-chip-ident-old">v4l2_chip_ident_old</structn <listitem> <para>New control <constant>V4L2_CID_COLORFX</constant> was added.</para> </listitem> - </orderedlist> - </section> + </orderedlist> + </section> <section> <title>V4L2 in Linux 2.6.32</title> <orderedlist> @@ -2322,8 +2322,16 @@ more information.</para> <listitem> <para>Added Remote Controller chapter, describing the default Remote Controller mapping for media devices.</para> </listitem> - </orderedlist> - </section> + </orderedlist> + </section> + <section> + <title>V4L2 in Linux 2.6.33</title> + <orderedlist> + <listitem> + <para>Added support for Digital Video timings in order to support HDTV receivers and transmitters.</para> + </listitem> + </orderedlist> + </section> </section> <section id="other"> diff --git a/Documentation/DocBook/v4l/v4l2.xml b/Documentation/DocBook/v4l/v4l2.xml index 937b4157a5d0..060105af49e5 100644 --- a/Documentation/DocBook/v4l/v4l2.xml +++ b/Documentation/DocBook/v4l/v4l2.xml @@ -74,6 +74,17 @@ Remote Controller chapter.</contrib> </address> </affiliation> </author> + + <author> + <firstname>Muralidharan</firstname> + <surname>Karicheri</surname> + <contrib>Documented the Digital Video timings API.</contrib> + <affiliation> + <address> + <email>m-karicheri2@ti.com</email> + </address> + </affiliation> + </author> </authorgroup> <copyright> @@ -89,7 +100,7 @@ Remote Controller chapter.</contrib> <year>2008</year> <year>2009</year> <holder>Bill Dirks, Michael H. Schimek, Hans Verkuil, Martin -Rubli, Andy Walls, Mauro Carvalho Chehab</holder> +Rubli, Andy Walls, Muralidharan Karicheri, Mauro Carvalho Chehab</holder> </copyright> <legalnotice> <para>Except when explicitly stated as GPL, programming examples within @@ -103,6 +114,13 @@ structs, ioctls) must be noted in more detail in the history chapter applications. --> <revision> + <revnumber>2.6.33</revnumber> + <date>2009-12-03</date> + <authorinitials>mk</authorinitials> + <revremark>Added documentation for the Digital Video timings API.</revremark> + </revision> + + <revision> <revnumber>2.6.32</revnumber> <date>2009-08-31</date> <authorinitials>mcc</authorinitials> @@ -355,7 +373,7 @@ and discussions on the V4L mailing list.</revremark> </partinfo> <title>Video for Linux Two API Specification</title> - <subtitle>Revision 2.6.32</subtitle> + <subtitle>Revision 2.6.33</subtitle> <chapter id="common"> &sub-common; @@ -411,6 +429,7 @@ and discussions on the V4L mailing list.</revremark> &sub-encoder-cmd; &sub-enumaudio; &sub-enumaudioout; + &sub-enum-dv-presets; &sub-enum-fmt; &sub-enum-framesizes; &sub-enum-frameintervals; @@ -421,6 +440,8 @@ and discussions on the V4L mailing list.</revremark> &sub-g-audioout; &sub-g-crop; &sub-g-ctrl; + &sub-g-dv-preset; + &sub-g-dv-timings; &sub-g-enc-index; &sub-g-ext-ctrls; &sub-g-fbuf; @@ -441,6 +462,7 @@ and discussions on the V4L mailing list.</revremark> &sub-querybuf; &sub-querycap; &sub-queryctrl; + &sub-query-dv-preset; &sub-querystd; &sub-reqbufs; &sub-s-hw-freq-seek; diff --git a/Documentation/DocBook/v4l/videodev2.h.xml b/Documentation/DocBook/v4l/videodev2.h.xml index 3e282ed9f593..068325940658 100644 --- a/Documentation/DocBook/v4l/videodev2.h.xml +++ b/Documentation/DocBook/v4l/videodev2.h.xml @@ -734,6 +734,99 @@ struct <link linkend="v4l2-standard">v4l2_standard</link> { }; /* + * V I D E O T I M I N G S D V P R E S E T + */ +struct <link linkend="v4l2-dv-preset">v4l2_dv_preset</link> { + __u32 preset; + __u32 reserved[4]; +}; + +/* + * D V P R E S E T S E N U M E R A T I O N + */ +struct <link linkend="v4l2-dv-enum-preset">v4l2_dv_enum_preset</link> { + __u32 index; + __u32 preset; + __u8 name[32]; /* Name of the preset timing */ + __u32 width; + __u32 height; + __u32 reserved[4]; +}; + +/* + * D V P R E S E T V A L U E S + */ +#define V4L2_DV_INVALID 0 +#define V4L2_DV_480P59_94 1 /* BT.1362 */ +#define V4L2_DV_576P50 2 /* BT.1362 */ +#define V4L2_DV_720P24 3 /* SMPTE 296M */ +#define V4L2_DV_720P25 4 /* SMPTE 296M */ +#define V4L2_DV_720P30 5 /* SMPTE 296M */ +#define V4L2_DV_720P50 6 /* SMPTE 296M */ +#define V4L2_DV_720P59_94 7 /* SMPTE 274M */ +#define V4L2_DV_720P60 8 /* SMPTE 274M/296M */ +#define V4L2_DV_1080I29_97 9 /* BT.1120/ SMPTE 274M */ +#define V4L2_DV_1080I30 10 /* BT.1120/ SMPTE 274M */ +#define V4L2_DV_1080I25 11 /* BT.1120 */ +#define V4L2_DV_1080I50 12 /* SMPTE 296M */ +#define V4L2_DV_1080I60 13 /* SMPTE 296M */ +#define V4L2_DV_1080P24 14 /* SMPTE 296M */ +#define V4L2_DV_1080P25 15 /* SMPTE 296M */ +#define V4L2_DV_1080P30 16 /* SMPTE 296M */ +#define V4L2_DV_1080P50 17 /* BT.1120 */ +#define V4L2_DV_1080P60 18 /* BT.1120 */ + +/* + * D V B T T I M I N G S + */ + +/* BT.656/BT.1120 timing data */ +struct <link linkend="v4l2-bt-timings">v4l2_bt_timings</link> { + __u32 width; /* width in pixels */ + __u32 height; /* height in lines */ + __u32 interlaced; /* Interlaced or progressive */ + __u32 polarities; /* Positive or negative polarity */ + __u64 pixelclock; /* Pixel clock in HZ. Ex. 74.25MHz->74250000 */ + __u32 hfrontporch; /* Horizpontal front porch in pixels */ + __u32 hsync; /* Horizontal Sync length in pixels */ + __u32 hbackporch; /* Horizontal back porch in pixels */ + __u32 vfrontporch; /* Vertical front porch in pixels */ + __u32 vsync; /* Vertical Sync length in lines */ + __u32 vbackporch; /* Vertical back porch in lines */ + __u32 il_vfrontporch; /* Vertical front porch for bottom field of + * interlaced field formats + */ + __u32 il_vsync; /* Vertical sync length for bottom field of + * interlaced field formats + */ + __u32 il_vbackporch; /* Vertical back porch for bottom field of + * interlaced field formats + */ + __u32 reserved[16]; +} __attribute__ ((packed)); + +/* Interlaced or progressive format */ +#define V4L2_DV_PROGRESSIVE 0 +#define V4L2_DV_INTERLACED 1 + +/* Polarities. If bit is not set, it is assumed to be negative polarity */ +#define V4L2_DV_VSYNC_POS_POL 0x00000001 +#define V4L2_DV_HSYNC_POS_POL 0x00000002 + + +/* DV timings */ +struct <link linkend="v4l2-dv-timings">v4l2_dv_timings</link> { + __u32 type; + union { + struct <link linkend="v4l2-bt-timings">v4l2_bt_timings</link> bt; + __u32 reserved[32]; + }; +} __attribute__ ((packed)); + +/* Values for the type field */ +#define V4L2_DV_BT_656_1120 0 /* BT.656/1120 timing type */ + +/* * V I D E O I N P U T S */ struct <link linkend="v4l2-input">v4l2_input</link> { @@ -744,7 +837,8 @@ struct <link linkend="v4l2-input">v4l2_input</link> { __u32 tuner; /* Associated tuner */ v4l2_std_id std; __u32 status; - __u32 reserved[4]; + __u32 capabilities; + __u32 reserved[3]; }; /* Values for the 'type' field */ @@ -775,6 +869,11 @@ struct <link linkend="v4l2-input">v4l2_input</link> { #define V4L2_IN_ST_NO_ACCESS 0x02000000 /* Conditional access denied */ #define V4L2_IN_ST_VTR 0x04000000 /* VTR time constant */ +/* capabilities flags */ +#define V4L2_IN_CAP_PRESETS 0x00000001 /* Supports S_DV_PRESET */ +#define V4L2_IN_CAP_CUSTOM_TIMINGS 0x00000002 /* Supports S_DV_TIMINGS */ +#define V4L2_IN_CAP_STD 0x00000004 /* Supports S_STD */ + /* * V I D E O O U T P U T S */ @@ -785,13 +884,19 @@ struct <link linkend="v4l2-output">v4l2_output</link> { __u32 audioset; /* Associated audios (bitfield) */ __u32 modulator; /* Associated modulator */ v4l2_std_id std; - __u32 reserved[4]; + __u32 capabilities; + __u32 reserved[3]; }; /* Values for the 'type' field */ #define V4L2_OUTPUT_TYPE_MODULATOR 1 #define V4L2_OUTPUT_TYPE_ANALOG 2 #define V4L2_OUTPUT_TYPE_ANALOGVGAOVERLAY 3 +/* capabilities flags */ +#define V4L2_OUT_CAP_PRESETS 0x00000001 /* Supports S_DV_PRESET */ +#define V4L2_OUT_CAP_CUSTOM_TIMINGS 0x00000002 /* Supports S_DV_TIMINGS */ +#define V4L2_OUT_CAP_STD 0x00000004 /* Supports S_STD */ + /* * C O N T R O L S */ @@ -1626,6 +1731,13 @@ struct <link linkend="v4l2-dbg-chip-ident">v4l2_dbg_chip_ident</link> { #endif #define VIDIOC_S_HW_FREQ_SEEK _IOW('V', 82, struct <link linkend="v4l2-hw-freq-seek">v4l2_hw_freq_seek</link>) +#define VIDIOC_ENUM_DV_PRESETS _IOWR('V', 83, struct <link linkend="v4l2-dv-enum-preset">v4l2_dv_enum_preset</link>) +#define VIDIOC_S_DV_PRESET _IOWR('V', 84, struct <link linkend="v4l2-dv-preset">v4l2_dv_preset</link>) +#define VIDIOC_G_DV_PRESET _IOWR('V', 85, struct <link linkend="v4l2-dv-preset">v4l2_dv_preset</link>) +#define VIDIOC_QUERY_DV_PRESET _IOR('V', 86, struct <link linkend="v4l2-dv-preset">v4l2_dv_preset</link>) +#define VIDIOC_S_DV_TIMINGS _IOWR('V', 87, struct <link linkend="v4l2-dv-timings">v4l2_dv_timings</link>) +#define VIDIOC_G_DV_TIMINGS _IOWR('V', 88, struct <link linkend="v4l2-dv-timings">v4l2_dv_timings</link>) + /* Reminder: when adding new ioctls please add support for them to drivers/media/video/v4l2-compat-ioctl32.c as well! */ diff --git a/Documentation/DocBook/v4l/vidioc-enum-dv-presets.xml b/Documentation/DocBook/v4l/vidioc-enum-dv-presets.xml new file mode 100644 index 000000000000..1d31427edd1b --- /dev/null +++ b/Documentation/DocBook/v4l/vidioc-enum-dv-presets.xml @@ -0,0 +1,238 @@ +<refentry id="vidioc-enum-dv-presets"> + <refmeta> + <refentrytitle>ioctl VIDIOC_ENUM_DV_PRESETS</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_ENUM_DV_PRESETS</refname> + <refpurpose>Enumerate supported Digital Video presets</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>struct v4l2_dv_enum_preset *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_ENUM_DV_PRESETS</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <para>To query the attributes of a DV preset, applications initialize the +<structfield>index</structfield> field and zero the reserved array of &v4l2-dv-enum-preset; +and call the <constant>VIDIOC_ENUM_DV_PRESETS</constant> ioctl with a pointer to this +structure. Drivers fill the rest of the structure or return an +&EINVAL; when the index is out of bounds. To enumerate all DV Presets supported, +applications shall begin at index zero, incrementing by one until the +driver returns <errorcode>EINVAL</errorcode>. Drivers may enumerate a +different set of DV presets after switching the video input or +output.</para> + + <table pgwide="1" frame="none" id="v4l2-dv-enum-preset"> + <title>struct <structname>v4l2_dv_enum_presets</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>index</structfield></entry> + <entry>Number of the DV preset, set by the +application.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>preset</structfield></entry> + <entry>This field identifies one of the DV preset values listed in <xref linkend="v4l2-dv-presets-vals"/>.</entry> + </row> + <row> + <entry>__u8</entry> + <entry><structfield>name</structfield>[24]</entry> + <entry>Name of the preset, a NUL-terminated ASCII string, for example: "720P-60", "1080I-60". This information is +intended for the user.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>width</structfield></entry> + <entry>Width of the active video in pixels for the DV preset.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>height</structfield></entry> + <entry>Height of the active video in lines for the DV preset.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[4]</entry> + <entry>Reserved for future extensions. Drivers must set the array to zero.</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="v4l2-dv-presets-vals"> + <title>struct <structname>DV Presets</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>Preset</entry> + <entry>Preset value</entry> + <entry>Description</entry> + </row> + <row> + <entry></entry> + <entry></entry> + <entry></entry> + </row> + <row> + <entry>V4L2_DV_INVALID</entry> + <entry>0</entry> + <entry>Invalid preset value.</entry> + </row> + <row> + <entry>V4L2_DV_480P59_94</entry> + <entry>1</entry> + <entry>720x480 progressive video at 59.94 fps as per BT.1362.</entry> + </row> + <row> + <entry>V4L2_DV_576P50</entry> + <entry>2</entry> + <entry>720x576 progressive video at 50 fps as per BT.1362.</entry> + </row> + <row> + <entry>V4L2_DV_720P24</entry> + <entry>3</entry> + <entry>1280x720 progressive video at 24 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_720P25</entry> + <entry>4</entry> + <entry>1280x720 progressive video at 25 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_720P30</entry> + <entry>5</entry> + <entry>1280x720 progressive video at 30 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_720P50</entry> + <entry>6</entry> + <entry>1280x720 progressive video at 50 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_720P59_94</entry> + <entry>7</entry> + <entry>1280x720 progressive video at 59.94 fps as per SMPTE 274M.</entry> + </row> + <row> + <entry>V4L2_DV_720P60</entry> + <entry>8</entry> + <entry>1280x720 progressive video at 60 fps as per SMPTE 274M/296M.</entry> + </row> + <row> + <entry>V4L2_DV_1080I29_97</entry> + <entry>9</entry> + <entry>1920x1080 interlaced video at 29.97 fps as per BT.1120/SMPTE 274M.</entry> + </row> + <row> + <entry>V4L2_DV_1080I30</entry> + <entry>10</entry> + <entry>1920x1080 interlaced video at 30 fps as per BT.1120/SMPTE 274M.</entry> + </row> + <row> + <entry>V4L2_DV_1080I25</entry> + <entry>11</entry> + <entry>1920x1080 interlaced video at 25 fps as per BT.1120.</entry> + </row> + <row> + <entry>V4L2_DV_1080I50</entry> + <entry>12</entry> + <entry>1920x1080 interlaced video at 50 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_1080I60</entry> + <entry>13</entry> + <entry>1920x1080 interlaced video at 60 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_1080P24</entry> + <entry>14</entry> + <entry>1920x1080 progressive video at 24 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_1080P25</entry> + <entry>15</entry> + <entry>1920x1080 progressive video at 25 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_1080P30</entry> + <entry>16</entry> + <entry>1920x1080 progressive video at 30 fps as per SMPTE 296M.</entry> + </row> + <row> + <entry>V4L2_DV_1080P50</entry> + <entry>17</entry> + <entry>1920x1080 progressive video at 50 fps as per BT.1120.</entry> + </row> + <row> + <entry>V4L2_DV_1080P60</entry> + <entry>18</entry> + <entry>1920x1080 progressive video at 60 fps as per BT.1120.</entry> + </row> + </tbody> + </tgroup> + </table> + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>EINVAL</errorcode></term> + <listitem> + <para>The &v4l2-dv-enum-preset; <structfield>index</structfield> +is out of bounds.</para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> +</refentry> + +<!-- +Local Variables: +mode: sgml +sgml-parent-document: "v4l2.sgml" +indent-tabs-mode: nil +End: +--> diff --git a/Documentation/DocBook/v4l/vidioc-enuminput.xml b/Documentation/DocBook/v4l/vidioc-enuminput.xml index 414856b82473..71b868e2fb8f 100644 --- a/Documentation/DocBook/v4l/vidioc-enuminput.xml +++ b/Documentation/DocBook/v4l/vidioc-enuminput.xml @@ -124,7 +124,13 @@ current input.</entry> </row> <row> <entry>__u32</entry> - <entry><structfield>reserved</structfield>[4]</entry> + <entry><structfield>capabilities</structfield></entry> + <entry>This field provides capabilities for the +input. See <xref linkend="input-capabilities" /> for flags.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[3]</entry> <entry>Reserved for future extensions. Drivers must set the array to zero.</entry> </row> @@ -261,6 +267,34 @@ flag is set Macrovision has been detected.</entry> </tbody> </tgroup> </table> + + <!-- Capability flags based on video timings RFC by Muralidharan +Karicheri, titled RFC (v1.2): V4L - Support for video timings at the +input/output interface to linux-media@vger.kernel.org on 19 Oct 2009. + --> + <table frame="none" pgwide="1" id="input-capabilities"> + <title>Input capabilities</title> + <tgroup cols="3"> + &cs-def; + <tbody valign="top"> + <row> + <entry><constant>V4L2_IN_CAP_PRESETS</constant></entry> + <entry>0x00000001</entry> + <entry>This input supports setting DV presets by using VIDIOC_S_DV_PRESET.</entry> + </row> + <row> + <entry><constant>V4L2_OUT_CAP_CUSTOM_TIMINGS</constant></entry> + <entry>0x00000002</entry> + <entry>This input supports setting custom video timings by using VIDIOC_S_DV_TIMINGS.</entry> + </row> + <row> + <entry><constant>V4L2_IN_CAP_STD</constant></entry> + <entry>0x00000004</entry> + <entry>This input supports setting the TV standard by using VIDIOC_S_STD.</entry> + </row> + </tbody> + </tgroup> + </table> </refsect1> <refsect1> diff --git a/Documentation/DocBook/v4l/vidioc-enumoutput.xml b/Documentation/DocBook/v4l/vidioc-enumoutput.xml index e8d16dcd50cf..a281d26a195f 100644 --- a/Documentation/DocBook/v4l/vidioc-enumoutput.xml +++ b/Documentation/DocBook/v4l/vidioc-enumoutput.xml @@ -114,7 +114,13 @@ details on video standards and how to switch see <xref </row> <row> <entry>__u32</entry> - <entry><structfield>reserved</structfield>[4]</entry> + <entry><structfield>capabilities</structfield></entry> + <entry>This field provides capabilities for the +output. See <xref linkend="output-capabilities" /> for flags.</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[3]</entry> <entry>Reserved for future extensions. Drivers must set the array to zero.</entry> </row> @@ -147,6 +153,34 @@ CVBS, S-Video, RGB.</entry> </tgroup> </table> + <!-- Capabilities flags based on video timings RFC by Muralidharan +Karicheri, titled RFC (v1.2): V4L - Support for video timings at the +input/output interface to linux-media@vger.kernel.org on 19 Oct 2009. + --> + <table frame="none" pgwide="1" id="output-capabilities"> + <title>Output capabilities</title> + <tgroup cols="3"> + &cs-def; + <tbody valign="top"> + <row> + <entry><constant>V4L2_OUT_CAP_PRESETS</constant></entry> + <entry>0x00000001</entry> + <entry>This output supports setting DV presets by using VIDIOC_S_DV_PRESET.</entry> + </row> + <row> + <entry><constant>V4L2_OUT_CAP_CUSTOM_TIMINGS</constant></entry> + <entry>0x00000002</entry> + <entry>This output supports setting custom video timings by using VIDIOC_S_DV_TIMINGS.</entry> + </row> + <row> + <entry><constant>V4L2_OUT_CAP_STD</constant></entry> + <entry>0x00000004</entry> + <entry>This output supports setting the TV standard by using VIDIOC_S_STD.</entry> + </row> + </tbody> + </tgroup> + </table> + </refsect1> <refsect1> &return-value; diff --git a/Documentation/DocBook/v4l/vidioc-g-dv-preset.xml b/Documentation/DocBook/v4l/vidioc-g-dv-preset.xml new file mode 100644 index 000000000000..3c6784e132f3 --- /dev/null +++ b/Documentation/DocBook/v4l/vidioc-g-dv-preset.xml @@ -0,0 +1,111 @@ +<refentry id="vidioc-g-dv-preset"> + <refmeta> + <refentrytitle>ioctl VIDIOC_G_DV_PRESET, VIDIOC_S_DV_PRESET</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_G_DV_PRESET</refname> + <refname>VIDIOC_S_DV_PRESET</refname> + <refpurpose>Query or select the DV preset of the current input or output</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>&v4l2-dv-preset; +*<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_G_DV_PRESET, VIDIOC_S_DV_PRESET</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + <para>To query and select the current DV preset, applications +use the <constant>VIDIOC_G_DV_PRESET</constant> and <constant>VIDIOC_S_DV_PRESET</constant> +ioctls which take a pointer to a &v4l2-dv-preset; type as argument. +Applications must zero the reserved array in &v4l2-dv-preset;. +<constant>VIDIOC_G_DV_PRESET</constant> returns a dv preset in the field +<structfield>preset</structfield> of &v4l2-dv-preset;.</para> + + <para><constant>VIDIOC_S_DV_PRESET</constant> accepts a pointer to a &v4l2-dv-preset; +that has the preset value to be set. Applications must zero the reserved array in &v4l2-dv-preset;. +If the preset is not supported, it returns an &EINVAL; </para> + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>EINVAL</errorcode></term> + <listitem> + <para>This ioctl is not supported, or the +<constant>VIDIOC_S_DV_PRESET</constant>,<constant>VIDIOC_S_DV_PRESET</constant> parameter was unsuitable.</para> + </listitem> + </varlistentry> + <varlistentry> + <term><errorcode>EBUSY</errorcode></term> + <listitem> + <para>The device is busy and therefore can not change the preset.</para> + </listitem> + </varlistentry> + </variablelist> + + <table pgwide="1" frame="none" id="v4l2-dv-preset"> + <title>struct <structname>v4l2_dv_preset</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>preset</structfield></entry> + <entry>Preset value to represent the digital video timings</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>reserved[4]</structfield></entry> + <entry>Reserved fields for future use</entry> + </row> + </tbody> + </tgroup> + </table> + + </refsect1> +</refentry> + +<!-- +Local Variables: +mode: sgml +sgml-parent-document: "v4l2.sgml" +indent-tabs-mode: nil +End: +--> diff --git a/Documentation/DocBook/v4l/vidioc-g-dv-timings.xml b/Documentation/DocBook/v4l/vidioc-g-dv-timings.xml new file mode 100644 index 000000000000..ecc19576bb8f --- /dev/null +++ b/Documentation/DocBook/v4l/vidioc-g-dv-timings.xml @@ -0,0 +1,224 @@ +<refentry id="vidioc-g-dv-timings"> + <refmeta> + <refentrytitle>ioctl VIDIOC_G_DV_TIMINGS, VIDIOC_S_DV_TIMINGS</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_G_DV_TIMINGS</refname> + <refname>VIDIOC_S_DV_TIMINGS</refname> + <refpurpose>Get or set custom DV timings for input or output</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>&v4l2-dv-timings; +*<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_G_DV_TIMINGS, VIDIOC_S_DV_TIMINGS</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + <para>To set custom DV timings for the input or output, applications use the +<constant>VIDIOC_S_DV_TIMINGS</constant> ioctl and to get the current custom timings, +applications use the <constant>VIDIOC_G_DV_TIMINGS</constant> ioctl. The detailed timing +information is filled in using the structure &v4l2-dv-timings;. These ioctls take +a pointer to the &v4l2-dv-timings; structure as argument. If the ioctl is not supported +or the timing values are not correct, the driver returns &EINVAL;.</para> + </refsect1> + + <refsect1> + &return-value; + + <variablelist> + <varlistentry> + <term><errorcode>EINVAL</errorcode></term> + <listitem> + <para>This ioctl is not supported, or the +<constant>VIDIOC_S_DV_TIMINGS</constant> parameter was unsuitable.</para> + </listitem> + </varlistentry> + <varlistentry> + <term><errorcode>EBUSY</errorcode></term> + <listitem> + <para>The device is busy and therefore can not change the timings.</para> + </listitem> + </varlistentry> + </variablelist> + + <table pgwide="1" frame="none" id="v4l2-bt-timings"> + <title>struct <structname>v4l2_bt_timings</structname></title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>width</structfield></entry> + <entry>Width of the active video in pixels</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>height</structfield></entry> + <entry>Height of the active video in lines</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>interlaced</structfield></entry> + <entry>Progressive (0) or interlaced (1)</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>polarities</structfield></entry> + <entry>This is a bit mask that defines polarities of sync signals. +bit 0 (V4L2_DV_VSYNC_POS_POL) is for vertical sync polarity and bit 1 (V4L2_DV_HSYNC_POS_POL) is for horizontal sync polarity. If the bit is set +(1) it is positive polarity and if is cleared (0), it is negative polarity.</entry> + </row> + <row> + <entry>__u64</entry> + <entry><structfield>pixelclock</structfield></entry> + <entry>Pixel clock in Hz. Ex. 74.25MHz->74250000</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>hfrontporch</structfield></entry> + <entry>Horizontal front porch in pixels</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>hsync</structfield></entry> + <entry>Horizontal sync length in pixels</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>hbackporch</structfield></entry> + <entry>Horizontal back porch in pixels</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>vfrontporch</structfield></entry> + <entry>Vertical front porch in lines</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>vsync</structfield></entry> + <entry>Vertical sync length in lines</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>vbackporch</structfield></entry> + <entry>Vertical back porch in lines</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>il_vfrontporch</structfield></entry> + <entry>Vertical front porch in lines for bottom field of interlaced field formats</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>il_vsync</structfield></entry> + <entry>Vertical sync length in lines for bottom field of interlaced field formats</entry> + </row> + <row> + <entry>__u32</entry> + <entry><structfield>il_vbackporch</structfield></entry> + <entry>Vertical back porch in lines for bottom field of interlaced field formats</entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="v4l2-dv-timings"> + <title>struct <structname>v4l2_dv_timings</structname></title> + <tgroup cols="4"> + &cs-str; + <tbody valign="top"> + <row> + <entry>__u32</entry> + <entry><structfield>type</structfield></entry> + <entry></entry> + <entry>Type of DV timings as listed in <xref linkend="dv-timing-types"/>.</entry> + </row> + <row> + <entry>union</entry> + <entry><structfield></structfield></entry> + <entry></entry> + </row> + <row> + <entry></entry> + <entry>&v4l2-bt-timings;</entry> + <entry><structfield>bt</structfield></entry> + <entry>Timings defined by BT.656/1120 specifications</entry> + </row> + <row> + <entry></entry> + <entry>__u32</entry> + <entry><structfield>reserved</structfield>[32]</entry> + <entry></entry> + </row> + </tbody> + </tgroup> + </table> + + <table pgwide="1" frame="none" id="dv-timing-types"> + <title>DV Timing types</title> + <tgroup cols="3"> + &cs-str; + <tbody valign="top"> + <row> + <entry>Timing type</entry> + <entry>value</entry> + <entry>Description</entry> + </row> + <row> + <entry></entry> + <entry></entry> + <entry></entry> + </row> + <row> + <entry>V4L2_DV_BT_656_1120</entry> + <entry>0</entry> + <entry>BT.656/1120 timings</entry> + </row> + </tbody> + </tgroup> + </table> + </refsect1> +</refentry> + +<!-- +Local Variables: +mode: sgml +sgml-parent-document: "v4l2.sgml" +indent-tabs-mode: nil +End: +--> diff --git a/Documentation/DocBook/v4l/vidioc-g-std.xml b/Documentation/DocBook/v4l/vidioc-g-std.xml index b6f5d267e856..912f8513e5da 100644 --- a/Documentation/DocBook/v4l/vidioc-g-std.xml +++ b/Documentation/DocBook/v4l/vidioc-g-std.xml @@ -86,6 +86,12 @@ standards.</para> <constant>VIDIOC_S_STD</constant> parameter was unsuitable.</para> </listitem> </varlistentry> + <varlistentry> + <term><errorcode>EBUSY</errorcode></term> + <listitem> + <para>The device is busy and therefore can not change the standard</para> + </listitem> + </varlistentry> </variablelist> </refsect1> </refentry> diff --git a/Documentation/DocBook/v4l/vidioc-query-dv-preset.xml b/Documentation/DocBook/v4l/vidioc-query-dv-preset.xml new file mode 100644 index 000000000000..87e4f0f6151c --- /dev/null +++ b/Documentation/DocBook/v4l/vidioc-query-dv-preset.xml @@ -0,0 +1,85 @@ +<refentry id="vidioc-query-dv-preset"> + <refmeta> + <refentrytitle>ioctl VIDIOC_QUERY_DV_PRESET</refentrytitle> + &manvol; + </refmeta> + + <refnamediv> + <refname>VIDIOC_QUERY_DV_PRESET</refname> + <refpurpose>Sense the DV preset received by the current +input</refpurpose> + </refnamediv> + + <refsynopsisdiv> + <funcsynopsis> + <funcprototype> + <funcdef>int <function>ioctl</function></funcdef> + <paramdef>int <parameter>fd</parameter></paramdef> + <paramdef>int <parameter>request</parameter></paramdef> + <paramdef>&v4l2-dv-preset; *<parameter>argp</parameter></paramdef> + </funcprototype> + </funcsynopsis> + </refsynopsisdiv> + + <refsect1> + <title>Arguments</title> + + <variablelist> + <varlistentry> + <term><parameter>fd</parameter></term> + <listitem> + <para>&fd;</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>request</parameter></term> + <listitem> + <para>VIDIOC_QUERY_DV_PRESET</para> + </listitem> + </varlistentry> + <varlistentry> + <term><parameter>argp</parameter></term> + <listitem> + <para></para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> + + <refsect1> + <title>Description</title> + + <para>The hardware may be able to detect the current DV preset +automatically, similar to sensing the video standard. To do so, applications +call <constant> VIDIOC_QUERY_DV_PRESET</constant> with a pointer to a +&v4l2-dv-preset; type. Once the hardware detects a preset, that preset is +returned in the preset field of &v4l2-dv-preset;. When detection is not +possible or fails, the value V4L2_DV_INVALID is returned.</para> + </refsect1> + + <refsect1> + &return-value; + <variablelist> + <varlistentry> + <term><errorcode>EINVAL</errorcode></term> + <listitem> + <para>This ioctl is not supported.</para> + </listitem> + </varlistentry> + <varlistentry> + <term><errorcode>EBUSY</errorcode></term> + <listitem> + <para>The device is busy and therefore can not sense the preset</para> + </listitem> + </varlistentry> + </variablelist> + </refsect1> +</refentry> + +<!-- +Local Variables: +mode: sgml +sgml-parent-document: "v4l2.sgml" +indent-tabs-mode: nil +End: +--> diff --git a/Documentation/DocBook/v4l/vidioc-querystd.xml b/Documentation/DocBook/v4l/vidioc-querystd.xml index b5a7ff934486..1a9e60393091 100644 --- a/Documentation/DocBook/v4l/vidioc-querystd.xml +++ b/Documentation/DocBook/v4l/vidioc-querystd.xml @@ -70,6 +70,12 @@ current video input or output.</para> <para>This ioctl is not supported.</para> </listitem> </varlistentry> + <varlistentry> + <term><errorcode>EBUSY</errorcode></term> + <listitem> + <para>The device is busy and therefore can not detect the standard</para> + </listitem> + </varlistentry> </variablelist> </refsect1> </refentry> diff --git a/Documentation/SubmitChecklist b/Documentation/SubmitChecklist index 78a9168ff377..1053a56be3b1 100644 --- a/Documentation/SubmitChecklist +++ b/Documentation/SubmitChecklist @@ -15,7 +15,7 @@ kernel patches. 2: Passes allnoconfig, allmodconfig 3: Builds on multiple CPU architectures by using local cross-compile tools - or something like PLM at OSDL. + or some other build farm. 4: ppc64 is a good architecture for cross-compilation checking because it tends to use `unsigned long' for 64-bit quantities. @@ -88,3 +88,6 @@ kernel patches. 24: All memory barriers {e.g., barrier(), rmb(), wmb()} need a comment in the source code that explains the logic of what they are doing and why. + +25: If any ioctl's are added by the patch, then also update + Documentation/ioctl/ioctl-number.txt. diff --git a/Documentation/acpi/method-customizing.txt b/Documentation/acpi/method-customizing.txt new file mode 100644 index 000000000000..e628cd23ca80 --- /dev/null +++ b/Documentation/acpi/method-customizing.txt @@ -0,0 +1,66 @@ +Linux ACPI Custom Control Method How To +======================================= + +Written by Zhang Rui <rui.zhang@intel.com> + + +Linux supports customizing ACPI control methods at runtime. + +Users can use this to +1. override an existing method which may not work correctly, + or just for debugging purposes. +2. insert a completely new method in order to create a missing + method such as _OFF, _ON, _STA, _INI, etc. +For these cases, it is far simpler to dynamically install a single +control method rather than override the entire DSDT, because kernel +rebuild/reboot is not needed and test result can be got in minutes. + +Note: Only ACPI METHOD can be overridden, any other object types like + "Device", "OperationRegion", are not recognized. +Note: The same ACPI control method can be overridden for many times, + and it's always the latest one that used by Linux/kernel. + +1. override an existing method + a) get the ACPI table via ACPI sysfs I/F. e.g. to get the DSDT, + just run "cat /sys/firmware/acpi/tables/DSDT > /tmp/dsdt.dat" + b) disassemble the table by running "iasl -d dsdt.dat". + c) rewrite the ASL code of the method and save it in a new file, + d) package the new file (psr.asl) to an ACPI table format. + Here is an example of a customized \_SB._AC._PSR method, + + DefinitionBlock ("", "SSDT", 1, "", "", 0x20080715) + { + External (ACON) + + Method (\_SB_.AC._PSR, 0, NotSerialized) + { + Store ("In AC _PSR", Debug) + Return (ACON) + } + } + Note that the full pathname of the method in ACPI namespace + should be used. + And remember to use "External" to declare external objects. + e) assemble the file to generate the AML code of the method. + e.g. "iasl psr.asl" (psr.aml is generated as a result) + f) mount debugfs by "mount -t debugfs none /sys/kernel/debug" + g) override the old method via the debugfs by running + "cat /tmp/psr.aml > /sys/kernel/debug/acpi/custom_method" + +2. insert a new method + This is easier than overriding an existing method. + We just need to create the ASL code of the method we want to + insert and then follow the step c) ~ g) in section 1. + +3. undo your changes + The "undo" operation is not supported for a new inserted method + right now, i.e. we can not remove a method currently. + For an overrided method, in order to undo your changes, please + save a copy of the method original ASL code in step c) section 1, + and redo step c) ~ g) to override the method with the original one. + + +Note: We can use a kernel with multiple custom ACPI method running, + But each individual write to debugfs can implement a SINGLE + method override. i.e. if we want to insert/override multiple + ACPI methods, we need to redo step c) ~ g) for multiple times. diff --git a/Documentation/blackfin/00-INDEX b/Documentation/blackfin/00-INDEX index d6840a91e1e1..c34e12440fec 100644 --- a/Documentation/blackfin/00-INDEX +++ b/Documentation/blackfin/00-INDEX @@ -1,9 +1,6 @@ 00-INDEX - This file -cache-lock.txt - - HOWTO for blackfin cache locking. - cachefeatures.txt - Supported cache features. diff --git a/Documentation/blackfin/Makefile b/Documentation/blackfin/Makefile new file mode 100644 index 000000000000..773dbb103f1c --- /dev/null +++ b/Documentation/blackfin/Makefile @@ -0,0 +1,6 @@ +obj-m := gptimers-example.o + +all: modules + +modules clean: + $(MAKE) -C ../.. SUBDIRS=$(PWD) $@ diff --git a/Documentation/blackfin/cache-lock.txt b/Documentation/blackfin/cache-lock.txt deleted file mode 100644 index 88ba1e6c31c3..000000000000 --- a/Documentation/blackfin/cache-lock.txt +++ /dev/null @@ -1,48 +0,0 @@ -/* - * File: Documentation/blackfin/cache-lock.txt - * Based on: - * Author: - * - * Created: - * Description: This file contains the simple DMA Implementation for Blackfin - * - * Rev: $Id: cache-lock.txt 2384 2006-11-01 04:12:43Z magicyang $ - * - * Modified: - * Copyright 2004-2006 Analog Devices Inc. - * - * Bugs: Enter bugs at http://blackfin.uclinux.org/ - * - */ - -How to lock your code in cache in uClinux/blackfin --------------------------------------------------- - -There are only a few steps required to lock your code into the cache. -Currently you can lock the code by Way. - -Below are the interface provided for locking the cache. - - -1. cache_grab_lock(int Ways); - -This function grab the lock for locking your code into the cache specified -by Ways. - - -2. cache_lock(int Ways); - -This function should be called after your critical code has been executed. -Once the critical code exits, the code is now loaded into the cache. This -function locks the code into the cache. - - -So, the example sequence will be: - - cache_grab_lock(WAY0_L); /* Grab the lock */ - - critical_code(); /* Execute the code of interest */ - - cache_lock(WAY0_L); /* Lock the cache */ - -Where WAY0_L signifies WAY0 locking. diff --git a/Documentation/blackfin/cachefeatures.txt b/Documentation/blackfin/cachefeatures.txt index 0fbec23becb5..75de51f94515 100644 --- a/Documentation/blackfin/cachefeatures.txt +++ b/Documentation/blackfin/cachefeatures.txt @@ -41,16 +41,6 @@ icplb_flush(); dcplb_flush(); - - Locking the cache. - - cache_grab_lock(); - cache_lock(); - - Please refer linux-2.6.x/Documentation/blackfin/cache-lock.txt for how to - lock the cache. - - Locking the cache is optional feature. - - Miscellaneous cache functions. flush_cache_all(); diff --git a/Documentation/blackfin/gptimers-example.c b/Documentation/blackfin/gptimers-example.c new file mode 100644 index 000000000000..b1bd6340e748 --- /dev/null +++ b/Documentation/blackfin/gptimers-example.c @@ -0,0 +1,83 @@ +/* + * Simple gptimers example + * http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:drivers:gptimers + * + * Copyright 2007-2009 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/interrupt.h> +#include <linux/module.h> + +#include <asm/gptimers.h> +#include <asm/portmux.h> + +/* ... random driver includes ... */ + +#define DRIVER_NAME "gptimer_example" + +struct gptimer_data { + uint32_t period, width; +}; +static struct gptimer_data data; + +/* ... random driver state ... */ + +static irqreturn_t gptimer_example_irq(int irq, void *dev_id) +{ + struct gptimer_data *data = dev_id; + + /* make sure it was our timer which caused the interrupt */ + if (!get_gptimer_intr(TIMER5_id)) + return IRQ_NONE; + + /* read the width/period values that were captured for the waveform */ + data->width = get_gptimer_pwidth(TIMER5_id); + data->period = get_gptimer_period(TIMER5_id); + + /* acknowledge the interrupt */ + clear_gptimer_intr(TIMER5_id); + + /* tell the upper layers we took care of things */ + return IRQ_HANDLED; +} + +/* ... random driver code ... */ + +static int __init gptimer_example_init(void) +{ + int ret; + + /* grab the peripheral pins */ + ret = peripheral_request(P_TMR5, DRIVER_NAME); + if (ret) { + printk(KERN_NOTICE DRIVER_NAME ": peripheral request failed\n"); + return ret; + } + + /* grab the IRQ for the timer */ + ret = request_irq(IRQ_TIMER5, gptimer_example_irq, IRQF_SHARED, DRIVER_NAME, &data); + if (ret) { + printk(KERN_NOTICE DRIVER_NAME ": IRQ request failed\n"); + peripheral_free(P_TMR5); + return ret; + } + + /* setup the timer and enable it */ + set_gptimer_config(TIMER5_id, WDTH_CAP | PULSE_HI | PERIOD_CNT | IRQ_ENA); + enable_gptimers(TIMER5bit); + + return 0; +} +module_init(gptimer_example_init); + +static void __exit gptimer_example_exit(void) +{ + disable_gptimers(TIMER5bit); + free_irq(IRQ_TIMER5, &data); + peripheral_free(P_TMR5); +} +module_exit(gptimer_example_exit); + +MODULE_LICENSE("BSD"); diff --git a/Documentation/dontdiff b/Documentation/dontdiff index e151b2a36267..3ad6acead949 100644 --- a/Documentation/dontdiff +++ b/Documentation/dontdiff @@ -103,6 +103,7 @@ gconf gen-devlist gen_crc32table gen_init_cpio +generated genheaders genksyms *_gray256.c diff --git a/Documentation/fb/viafb.txt b/Documentation/fb/viafb.txt index 67dbf442b0b6..f3e046a6a987 100644 --- a/Documentation/fb/viafb.txt +++ b/Documentation/fb/viafb.txt @@ -7,7 +7,7 @@ VIA UniChrome Family(CLE266, PM800 / CN400 / CN300, P4M800CE / P4M800Pro / CN700 / VN800, CX700 / VX700, K8M890, P4M890, - CN896 / P4M900, VX800) + CN896 / P4M900, VX800, VX855) [Driver features] ------------------------ @@ -154,13 +154,6 @@ 0 : No Dual Edge Panel (default) 1 : Dual Edge Panel - viafb_video_dev: - This option is used to specify video output devices(CRT, DVI, LCD) for - duoview case. - For example: - To output video on DVI, we should use: - modprobe viafb viafb_video_dev=DVI... - viafb_lcd_port: This option is used to specify LCD output port, available values are "DVP0" "DVP1" "DFP_HIGHLOW" "DFP_HIGH" "DFP_LOW". @@ -181,9 +174,6 @@ Notes: and bpp, need to call VIAFB specified ioctl interface VIAFB_SET_DEVICE instead of calling common ioctl function FBIOPUT_VSCREENINFO since viafb doesn't support multi-head well, or it will cause screen crush. - 4. VX800 2D accelerator hasn't been supported in this driver yet. When - using driver on VX800, the driver will disable the acceleration - function as default. [Configure viafb with "fbset" tool] diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index 21ab9357326d..870d190fe617 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -474,3 +474,22 @@ Why: Obsoleted by the adt7475 driver. Who: Jean Delvare <khali@linux-fr.org> --------------------------- +What: Support for lcd_switch and display_get in asus-laptop driver +When: March 2010 +Why: These two features use non-standard interfaces. There are the + only features that really need multiple path to guess what's + the right method name on a specific laptop. + + Removing them will allow to remove a lot of code an significantly + clean the drivers. + + This will affect the backlight code which won't be able to know + if the backlight is on or off. The platform display file will also be + write only (like the one in eeepc-laptop). + + This should'nt affect a lot of user because they usually know + when their display is on or off. + +Who: Corentin Chary <corentin.chary@gmail.com> + +---------------------------- diff --git a/Documentation/filesystems/00-INDEX b/Documentation/filesystems/00-INDEX index 7001782ab932..875d49696b6e 100644 --- a/Documentation/filesystems/00-INDEX +++ b/Documentation/filesystems/00-INDEX @@ -1,7 +1,5 @@ 00-INDEX - this file (info on some of the filesystems supported by linux). -Exporting - - explanation of how to make filesystems exportable. Locking - info on locking rules as they pertain to Linux VFS. 9p.txt @@ -68,12 +66,8 @@ mandatory-locking.txt - info on the Linux implementation of Sys V mandatory file locking. ncpfs.txt - info on Novell Netware(tm) filesystem using NCP protocol. -nfs41-server.txt - - info on the Linux server implementation of NFSv4 minor version 1. -nfs-rdma.txt - - how to install and setup the Linux NFS/RDMA client and server software. -nfsroot.txt - - short guide on setting up a diskless box with NFS root filesystem. +nfs/ + - nfs-related documentation. nilfs2.txt - info and mount options for the NILFS2 filesystem. ntfs.txt @@ -92,8 +86,6 @@ relay.txt - info on relay, for efficient streaming from kernel to user space. romfs.txt - description of the ROMFS filesystem. -rpc-cache.txt - - introduction to the caching mechanisms in the sunrpc layer. seq_file.txt - how to use the seq_file API sharedsubtree.txt diff --git a/Documentation/filesystems/nfs/00-INDEX b/Documentation/filesystems/nfs/00-INDEX new file mode 100644 index 000000000000..2f68cd688769 --- /dev/null +++ b/Documentation/filesystems/nfs/00-INDEX @@ -0,0 +1,16 @@ +00-INDEX + - this file (nfs-related documentation). +Exporting + - explanation of how to make filesystems exportable. +knfsd-stats.txt + - statistics which the NFS server makes available to user space. +nfs.txt + - nfs client, and DNS resolution for fs_locations. +nfs41-server.txt + - info on the Linux server implementation of NFSv4 minor version 1. +nfs-rdma.txt + - how to install and setup the Linux NFS/RDMA client and server software +nfsroot.txt + - short guide on setting up a diskless box with NFS root filesystem. +rpc-cache.txt + - introduction to the caching mechanisms in the sunrpc layer. diff --git a/Documentation/filesystems/Exporting b/Documentation/filesystems/nfs/Exporting index 87019d2b5981..87019d2b5981 100644 --- a/Documentation/filesystems/Exporting +++ b/Documentation/filesystems/nfs/Exporting diff --git a/Documentation/filesystems/knfsd-stats.txt b/Documentation/filesystems/nfs/knfsd-stats.txt index 64ced5149d37..64ced5149d37 100644 --- a/Documentation/filesystems/knfsd-stats.txt +++ b/Documentation/filesystems/nfs/knfsd-stats.txt diff --git a/Documentation/filesystems/nfs-rdma.txt b/Documentation/filesystems/nfs/nfs-rdma.txt index e386f7e4bcee..e386f7e4bcee 100644 --- a/Documentation/filesystems/nfs-rdma.txt +++ b/Documentation/filesystems/nfs/nfs-rdma.txt diff --git a/Documentation/filesystems/nfs.txt b/Documentation/filesystems/nfs/nfs.txt index f50f26ce6cd0..f50f26ce6cd0 100644 --- a/Documentation/filesystems/nfs.txt +++ b/Documentation/filesystems/nfs/nfs.txt diff --git a/Documentation/filesystems/nfs41-server.txt b/Documentation/filesystems/nfs/nfs41-server.txt index 5920fe26e6ff..1bd0d0c05171 100644 --- a/Documentation/filesystems/nfs41-server.txt +++ b/Documentation/filesystems/nfs/nfs41-server.txt @@ -41,7 +41,7 @@ interoperability problems with future clients. Known issues: conformant with the spec (for example, we don't use kerberos on the backchannel correctly). - no trunking support: no clients currently take advantage of - trunking, but this is a mandatory failure, and its use is + trunking, but this is a mandatory feature, and its use is recommended to clients in a number of places. (E.g. to ensure timely renewal in case an existing connection's retry timeouts have gotten too long; see section 8.3 of the draft.) @@ -213,3 +213,10 @@ The following cases aren't supported yet: DESTROY_CLIENTID, DESTROY_SESSION, EXCHANGE_ID. * DESTROY_SESSION MUST be the final operation in the COMPOUND request. +Nonstandard compound limitations: +* No support for a sessions fore channel RPC compound that requires both a + ca_maxrequestsize request and a ca_maxresponsesize reply, so we may + fail to live up to the promise we made in CREATE_SESSION fore channel + negotiation. +* No more than one IO operation (read, write, readdir) allowed per + compound. diff --git a/Documentation/filesystems/nfsroot.txt b/Documentation/filesystems/nfs/nfsroot.txt index 3ba0b945aaf8..3ba0b945aaf8 100644 --- a/Documentation/filesystems/nfsroot.txt +++ b/Documentation/filesystems/nfs/nfsroot.txt diff --git a/Documentation/filesystems/rpc-cache.txt b/Documentation/filesystems/nfs/rpc-cache.txt index 8a382bea6808..8a382bea6808 100644 --- a/Documentation/filesystems/rpc-cache.txt +++ b/Documentation/filesystems/nfs/rpc-cache.txt diff --git a/Documentation/filesystems/porting b/Documentation/filesystems/porting index 92b888d540a6..a7e9746ee7ea 100644 --- a/Documentation/filesystems/porting +++ b/Documentation/filesystems/porting @@ -140,7 +140,7 @@ Callers of notify_change() need ->i_mutex now. New super_block field "struct export_operations *s_export_op" for explicit support for exporting, e.g. via NFS. The structure is fully documented at its declaration in include/linux/fs.h, and in -Documentation/filesystems/Exporting. +Documentation/filesystems/nfs/Exporting. Briefly it allows for the definition of decode_fh and encode_fh operations to encode and decode filehandles, and allows the filesystem to use diff --git a/Documentation/filesystems/seq_file.txt b/Documentation/filesystems/seq_file.txt index 0d15ebccf5b0..a1e2e0dda907 100644 --- a/Documentation/filesystems/seq_file.txt +++ b/Documentation/filesystems/seq_file.txt @@ -248,9 +248,7 @@ code, that is done in the initialization code in the usual way: { struct proc_dir_entry *entry; - entry = create_proc_entry("sequence", 0, NULL); - if (entry) - entry->proc_fops = &ct_file_ops; + proc_create("sequence", 0, NULL, &ct_file_ops); return 0; } diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt index e4e7daed2ba8..1866c27eec69 100644 --- a/Documentation/gpio.txt +++ b/Documentation/gpio.txt @@ -531,6 +531,13 @@ and have the following read/write attributes: This file exists only if the pin can be configured as an interrupt generating input pin. + "active_low" ... reads as either 0 (false) or 1 (true). Write + any nonzero value to invert the value attribute both + for reading and writing. Existing and subsequent + poll(2) support configuration via the edge attribute + for "rising" and "falling" edges will follow this + setting. + GPIO controllers have paths like /sys/class/gpio/gpiochip42/ (for the controller implementing GPIOs starting at #42) and have the following read-only attributes: @@ -566,6 +573,8 @@ requested using gpio_request(): int gpio_export_link(struct device *dev, const char *name, unsigned gpio) + /* change the polarity of a GPIO node in sysfs */ + int gpio_sysfs_set_active_low(unsigned gpio, int value); After a kernel driver requests a GPIO, it may only be made available in the sysfs interface by gpio_export(). The driver can control whether the @@ -580,3 +589,9 @@ After the GPIO has been exported, gpio_export_link() allows creating symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can use this to provide the interface under their own device in sysfs with a descriptive name. + +Drivers can use gpio_sysfs_set_active_low() to hide GPIO line polarity +differences between boards from user space. This only affects the +sysfs interface. Polarity change can be done both before and after +gpio_export(), and previously enabled poll(2) support for either +rising or falling edge will be reconfigured to follow this setting. diff --git a/Documentation/infiniband/ipoib.txt b/Documentation/infiniband/ipoib.txt index 6d40f00b358c..64eeb55d0c09 100644 --- a/Documentation/infiniband/ipoib.txt +++ b/Documentation/infiniband/ipoib.txt @@ -36,11 +36,11 @@ Datagram vs Connected modes fabric with a 2K MTU, the IPoIB MTU will be 2048 - 4 = 2044 bytes. In connected mode, the IB RC (Reliable Connected) transport is used. - Connected mode is to takes advantage of the connected nature of the - IB transport and allows an MTU up to the maximal IP packet size of - 64K, which reduces the number of IP packets needed for handling - large UDP datagrams, TCP segments, etc and increases the performance - for large messages. + Connected mode takes advantage of the connected nature of the IB + transport and allows an MTU up to the maximal IP packet size of 64K, + which reduces the number of IP packets needed for handling large UDP + datagrams, TCP segments, etc and increases the performance for large + messages. In connected mode, the interface's UD QP is still used for multicast and communication with peers that don't support connected mode. In diff --git a/Documentation/kbuild/kbuild.txt b/Documentation/kbuild/kbuild.txt index bb3bf38f03da..6f8c1cabbc5d 100644 --- a/Documentation/kbuild/kbuild.txt +++ b/Documentation/kbuild/kbuild.txt @@ -1,3 +1,17 @@ +Output files + +modules.order +-------------------------------------------------- +This file records the order in which modules appear in Makefiles. This +is used by modprobe to deterministically resolve aliases that match +multiple modules. + +modules.builtin +-------------------------------------------------- +This file lists all modules that are built into the kernel. This is used +by modprobe to not fail when trying to load something builtin. + + Environment variables KCPPFLAGS diff --git a/Documentation/kbuild/kconfig.txt b/Documentation/kbuild/kconfig.txt index 849b5e56d06f..49efae703979 100644 --- a/Documentation/kbuild/kconfig.txt +++ b/Documentation/kbuild/kconfig.txt @@ -103,10 +103,16 @@ KCONFIG_AUTOCONFIG This environment variable can be set to specify the path & name of the "auto.conf" file. Its default value is "include/config/auto.conf". +KCONFIG_TRISTATE +-------------------------------------------------- +This environment variable can be set to specify the path & name of the +"tristate.conf" file. Its default value is "include/config/tristate.conf". + KCONFIG_AUTOHEADER -------------------------------------------------- This environment variable can be set to specify the path & name of the -"autoconf.h" (header) file. Its default value is "include/linux/autoconf.h". +"autoconf.h" (header) file. +Its default value is "include/generated/autoconf.h". ====================================================================== diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index ab95d3ada5c7..5ba4d9dff113 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -1032,7 +1032,7 @@ and is between 256 and 4096 characters. It is defined in the file No delay ip= [IP_PNP] - See Documentation/filesystems/nfsroot.txt. + See Documentation/filesystems/nfs/nfsroot.txt. ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards See comment before ip2_setup() in @@ -1553,10 +1553,10 @@ and is between 256 and 4096 characters. It is defined in the file going to be removed in 2.6.29. nfsaddrs= [NFS] - See Documentation/filesystems/nfsroot.txt. + See Documentation/filesystems/nfs/nfsroot.txt. nfsroot= [NFS] nfs root filesystem for disk-less boxes. - See Documentation/filesystems/nfsroot.txt. + See Documentation/filesystems/nfs/nfsroot.txt. nfs.callback_tcpport= [NFS] set the TCP port on which the NFSv4 callback @@ -2729,6 +2729,11 @@ and is between 256 and 4096 characters. It is defined in the file vmpoff= [KNL,S390] Perform z/VM CP command after power off. Format: <command> + vt.cur_default= [VT] Default cursor shape. + Format: 0xCCBBAA, where AA, BB, and CC are the same as + the parameters of the <Esc>[?A;B;Cc escape sequence; + see VGA-softcursor.txt. Default: 2 = underline. + vt.default_blu= [VT] Format: <blue0>,<blue1>,<blue2>,...,<blue15> Change the default blue palette of the console. diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index aafcaa634191..169091f75e6d 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -1,7 +1,7 @@ ThinkPad ACPI Extras Driver - Version 0.23 - April 10th, 2009 + Version 0.24 + December 11th, 2009 Borislav Deianov <borislav@users.sf.net> Henrique de Moraes Holschuh <hmh@hmh.eng.br> @@ -460,6 +460,8 @@ event code Key Notes For Lenovo ThinkPads with a new BIOS, it has to be handled either by the ACPI OSI, or by userspace. + The driver does the right thing, + never mess with this. 0x1011 0x10 FN+END Brightness down. See brightness up for details. @@ -582,46 +584,15 @@ with hotkey_report_mode. Brightness hotkey notes: -These are the current sane choices for brightness key mapping in -thinkpad-acpi: +Don't mess with the brightness hotkeys in a Thinkpad. If you want +notifications for OSD, use the sysfs backlight class event support. -For IBM and Lenovo models *without* ACPI backlight control (the ones on -which thinkpad-acpi will autoload its backlight interface by default, -and on which ACPI video does not export a backlight interface): - -1. Don't enable or map the brightness hotkeys in thinkpad-acpi, as - these older firmware versions unfortunately won't respect the hotkey - mask for brightness keys anyway, and always reacts to them. This - usually work fine, unless X.org drivers are doing something to block - the BIOS. In that case, use (3) below. This is the default mode of - operation. - -2. Enable the hotkeys, but map them to something else that is NOT - KEY_BRIGHTNESS_UP/DOWN or any other keycode that would cause - userspace to try to change the backlight level, and use that as an - on-screen-display hint. - -3. IF AND ONLY IF X.org drivers find a way to block the firmware from - automatically changing the brightness, enable the hotkeys and map - them to KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN, and feed that to - something that calls xbacklight. thinkpad-acpi will not be able to - change brightness in that case either, so you should disable its - backlight interface. - -For Lenovo models *with* ACPI backlight control: - -1. Load up ACPI video and use that. ACPI video will report ACPI - events for brightness change keys. Do not mess with thinkpad-acpi - defaults in this case. thinkpad-acpi should not have anything to do - with backlight events in a scenario where ACPI video is loaded: - brightness hotkeys must be disabled, and the backlight interface is - to be kept disabled as well. This is the default mode of operation. - -2. Do *NOT* load up ACPI video, enable the hotkeys in thinkpad-acpi, - and map them to KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN. Process - these keys on userspace somehow (e.g. by calling xbacklight). - The driver will do this automatically if it detects that ACPI video - has been disabled. +The driver will issue KEY_BRIGHTNESS_UP and KEY_BRIGHTNESS_DOWN events +automatically for the cases were userspace has to do something to +implement brightness changes. When you override these events, you will +either fail to handle properly the ThinkPads that require explicit +action to change backlight brightness, or the ThinkPads that require +that no action be taken to work properly. Bluetooth @@ -1121,25 +1092,61 @@ WARNING: its level up and down at every change. -Volume control -- /proc/acpi/ibm/volume ---------------------------------------- +Volume control +-------------- + +procfs: /proc/acpi/ibm/volume +ALSA: "ThinkPad Console Audio Control", default ID: "ThinkPadEC" + +NOTE: by default, the volume control interface operates in read-only +mode, as it is supposed to be used for on-screen-display purposes. +The read/write mode can be enabled through the use of the +"volume_control=1" module parameter. -This feature allows volume control on ThinkPad models which don't have -a hardware volume knob. The available commands are: +NOTE: distros are urged to not enable volume_control by default, this +should be done by the local admin only. The ThinkPad UI is for the +console audio control to be done through the volume keys only, and for +the desktop environment to just provide on-screen-display feedback. +Software volume control should be done only in the main AC97/HDA +mixer. + +This feature allows volume control on ThinkPad models with a digital +volume knob (when available, not all models have it), as well as +mute/unmute control. The available commands are: echo up >/proc/acpi/ibm/volume echo down >/proc/acpi/ibm/volume echo mute >/proc/acpi/ibm/volume + echo unmute >/proc/acpi/ibm/volume echo 'level <level>' >/proc/acpi/ibm/volume -The <level> number range is 0 to 15 although not all of them may be +The <level> number range is 0 to 14 although not all of them may be distinct. The unmute the volume after the mute command, use either the -up or down command (the level command will not unmute the volume). +up or down command (the level command will not unmute the volume), or +the unmute command. + The current volume level and mute state is shown in the file. -The ALSA mixer interface to this feature is still missing, but patches -to add it exist. That problem should be addressed in the not so -distant future. +You can use the volume_capabilities parameter to tell the driver +whether your thinkpad has volume control or mute-only control: +volume_capabilities=1 for mixers with mute and volume control, +volume_capabilities=2 for mixers with only mute control. + +If the driver misdetects the capabilities for your ThinkPad model, +please report this to ibm-acpi-devel@lists.sourceforge.net, so that we +can update the driver. + +There are two strategies for volume control. To select which one +should be used, use the volume_mode module parameter: volume_mode=1 +selects EC mode, and volume_mode=3 selects EC mode with NVRAM backing +(so that volume/mute changes are remembered across shutdown/reboot). + +The driver will operate in volume_mode=3 by default. If that does not +work well on your ThinkPad model, please report this to +ibm-acpi-devel@lists.sourceforge.net. + +The driver supports the standard ALSA module parameters. If the ALSA +mixer is disabled, the driver will disable all volume functionality. Fan control and monitoring: fan speed, fan enable/disable @@ -1405,6 +1412,7 @@ to enable more than one output class, just add their values. 0x0008 HKEY event interface, hotkeys 0x0010 Fan control 0x0020 Backlight brightness + 0x0040 Audio mixer/volume control There is also a kernel build option to enable more debugging information, which may be necessary to debug driver problems. @@ -1465,3 +1473,9 @@ Sysfs interface changelog: and it is always able to disable hot keys. Very old thinkpads are properly supported. hotkey_bios_mask is deprecated and marked for removal. + +0x020600: Marker for backlight change event support. + +0x020700: Support for mute-only mixers. + Volume control in read-only mode by default. + Marker for ALSA mixer support. diff --git a/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt new file mode 100644 index 000000000000..515ebcf1b97d --- /dev/null +++ b/Documentation/powerpc/dts-bindings/4xx/ppc440spe-adma.txt @@ -0,0 +1,93 @@ +PPC440SPe DMA/XOR (DMA Controller and XOR Accelerator) + +Device nodes needed for operation of the ppc440spe-adma driver +are specified hereby. These are I2O/DMA, DMA and XOR nodes +for DMA engines and Memory Queue Module node. The latter is used +by ADMA driver for configuration of RAID-6 H/W capabilities of +the PPC440SPe. In addition to the nodes and properties described +below, the ranges property of PLB node must specify ranges for +DMA devices. + + i) The I2O node + + Required properties: + + - compatible : "ibm,i2o-440spe"; + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + + Example: + + I2O: i2o@400100000 { + compatible = "ibm,i2o-440spe"; + reg = <0x00000004 0x00100000 0x100>; + dcr-reg = <0x060 0x020>; + }; + + + ii) The DMA node + + Required properties: + + - compatible : "ibm,dma-440spe"; + - cell-index : 1 cell, hardware index of the DMA engine + (typically 0x0 and 0x1 for DMA0 and DMA1) + - reg : <registers mapping> + - dcr-reg : <DCR registers range> + - interrupts : <interrupt mapping for DMA0/1 interrupts sources: + 2 sources: DMAx CS FIFO Needs Service IRQ (on UIC0) + and DMA Error IRQ (on UIC1). The latter is common + for both DMA engines>. + - interrupt-parent : needed for interrupt mapping + + Example: + + DMA0: dma0@400100100 { + compatible = "ibm,dma-440spe"; + cell-index = <0>; + reg = <0x00000004 0x00100100 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA0>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x14 4 + 1 &UIC1 0x16 4>; + }; + + + iii) XOR Accelerator node + + Required properties: + + - compatible : "amcc,xor-accelerator"; + - reg : <registers mapping> + - interrupts : <interrupt mapping for XOR interrupt source> + - interrupt-parent : for interrupt mapping + + Example: + + xor-accel@400200000 { + compatible = "amcc,xor-accelerator"; + reg = <0x00000004 0x00200000 0x400>; + interrupt-parent = <&UIC1>; + interrupts = <0x1f 4>; + }; + + + iv) Memory Queue Module node + + Required properties: + + - compatible : "ibm,mq-440spe"; + - dcr-reg : <DCR registers range> + + Example: + + MQ0: mq { + compatible = "ibm,mq-440spe"; + dcr-reg = <0x040 0x020>; + }; + diff --git a/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt new file mode 100644 index 000000000000..b558585b1aaf --- /dev/null +++ b/Documentation/powerpc/dts-bindings/nintendo/gamecube.txt @@ -0,0 +1,109 @@ + +Nintendo GameCube device tree +============================= + +1) The "flipper" node + + This node represents the multi-function "Flipper" chip, which packages + many of the devices found in the Nintendo GameCube. + + Required properties: + + - compatible : Should be "nintendo,flipper" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the interrupt controller within the "Flipper" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - compatible : should be "nintendo,flipper-pic" + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.c.i) The Auxiliary RAM (ARAM) node + + Represents the non cpu-addressable ram designed mainly to store audio + related information. + The ARAM node must be placed under the DSP node. + + Required properties: + + - compatible : should be "nintendo,flipper-aram" + - reg : should contain the ARAM start (zero-based) and length + +1.d) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,flipper-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.g) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + diff --git a/Documentation/powerpc/dts-bindings/nintendo/wii.txt b/Documentation/powerpc/dts-bindings/nintendo/wii.txt new file mode 100644 index 000000000000..a7e155a023b8 --- /dev/null +++ b/Documentation/powerpc/dts-bindings/nintendo/wii.txt @@ -0,0 +1,184 @@ + +Nintendo Wii device tree +======================== + +0) The root node + + This node represents the Nintendo Wii video game console. + + Required properties: + + - model : Should be "nintendo,wii" + - compatible : Should be "nintendo,wii" + +1) The "hollywood" node + + This node represents the multi-function "Hollywood" chip, which packages + many of the devices found in the Nintendo Wii. + + Required properties: + + - compatible : Should be "nintendo,hollywood" + +1.a) The Video Interface (VI) node + + Represents the interface between the graphics processor and a external + video encoder. + + Required properties: + + - compatible : should be "nintendo,hollywood-vi","nintendo,flipper-vi" + - reg : should contain the VI registers location and length + - interrupts : should contain the VI interrupt + +1.b) The Processor Interface (PI) node + + Represents the data and control interface between the main processor + and graphics and audio processor. + + Required properties: + + - compatible : should be "nintendo,hollywood-pi","nintendo,flipper-pi" + - reg : should contain the PI registers location and length + +1.b.i) The "Flipper" interrupt controller node + + Represents the "Flipper" interrupt controller within the "Hollywood" chip. + The node for the "Flipper" interrupt controller must be placed under + the PI node. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,flipper-pic" + - interrupt-controller + +1.c) The Digital Signal Procesor (DSP) node + + Represents the digital signal processor interface, designed to offload + audio related tasks. + + Required properties: + + - compatible : should be "nintendo,hollywood-dsp","nintendo,flipper-dsp" + - reg : should contain the DSP registers location and length + - interrupts : should contain the DSP interrupt + +1.d) The Serial Interface (SI) node + + Represents the interface to the four single bit serial interfaces. + The SI is a proprietary serial interface used normally to control gamepads. + It's NOT a RS232-type interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-si","nintendo,flipper-si" + - reg : should contain the SI registers location and length + - interrupts : should contain the SI interrupt + +1.e) The Audio Interface (AI) node + + Represents the interface to the external 16-bit stereo digital-to-analog + converter. + + Required properties: + + - compatible : should be "nintendo,hollywood-ai","nintendo,flipper-ai" + - reg : should contain the AI registers location and length + - interrupts : should contain the AI interrupt + +1.f) The External Interface (EXI) node + + Represents the multi-channel SPI-like interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-exi","nintendo,flipper-exi" + - reg : should contain the EXI registers location and length + - interrupts : should contain the EXI interrupt + +1.g) The Open Host Controller Interface (OHCI) nodes + + Represent the USB 1.x Open Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ohci","usb-ohci" + - reg : should contain the OHCI registers location and length + - interrupts : should contain the OHCI interrupt + +1.h) The Enhanced Host Controller Interface (EHCI) node + + Represents the USB 2.0 Enhanced Host Controller Interface. + + Required properties: + + - compatible : should be "nintendo,hollywood-usb-ehci","usb-ehci" + - reg : should contain the EHCI registers location and length + - interrupts : should contain the EHCI interrupt + +1.i) The Secure Digital Host Controller Interface (SDHCI) nodes + + Represent the Secure Digital Host Controller Interfaces. + + Required properties: + + - compatible : should be "nintendo,hollywood-sdhci","sdhci" + - reg : should contain the SDHCI registers location and length + - interrupts : should contain the SDHCI interrupt + +1.j) The Inter-Processsor Communication (IPC) node + + Represent the Inter-Processor Communication interface. This interface + enables communications between the Broadway and the Starlet processors. + + - compatible : should be "nintendo,hollywood-ipc" + - reg : should contain the IPC registers location and length + - interrupts : should contain the IPC interrupt + +1.k) The "Hollywood" interrupt controller node + + Represents the "Hollywood" interrupt controller within the + "Hollywood" chip. + + Required properties: + + - #interrupt-cells : <1> + - compatible : should be "nintendo,hollywood-pic" + - reg : should contain the controller registers location and length + - interrupt-controller + - interrupts : should contain the cascade interrupt of the "flipper" pic + - interrupt-parent: should contain the phandle of the "flipper" pic + +1.l) The General Purpose I/O (GPIO) controller node + + Represents the dual access 32 GPIO controller interface. + + Required properties: + + - #gpio-cells : <2> + - compatible : should be "nintendo,hollywood-gpio" + - reg : should contain the IPC registers location and length + - gpio-controller + +1.m) The control node + + Represents the control interface used to setup several miscellaneous + settings of the "Hollywood" chip like boot memory mappings, resets, + disk interface mode, etc. + + Required properties: + + - compatible : should be "nintendo,hollywood-control" + - reg : should contain the control registers location and length + +1.n) The Disk Interface (DI) node + + Represents the interface used to communicate with mass storage devices. + + Required properties: + + - compatible : should be "nintendo,hollywood-di" + - reg : should contain the DI registers location and length + - interrupts : should contain the DI interrupt + diff --git a/Documentation/thermal/sysfs-api.txt b/Documentation/thermal/sysfs-api.txt index a87dc277a5ca..cb3d15bc1aeb 100644 --- a/Documentation/thermal/sysfs-api.txt +++ b/Documentation/thermal/sysfs-api.txt @@ -206,6 +206,7 @@ passive passive trip point for the zone. Activation is done by polling with an interval of 1 second. Unit: millidegrees Celsius + Valid values: 0 (disabled) or greater than 1000 RW, Optional ***************************** diff --git a/Documentation/video4linux/gspca.txt b/Documentation/video4linux/gspca.txt index 319d9838e87e..1800a62cf135 100644 --- a/Documentation/video4linux/gspca.txt +++ b/Documentation/video4linux/gspca.txt @@ -12,6 +12,7 @@ m5602 0402:5602 ALi Video Camera Controller spca501 040a:0002 Kodak DVC-325 spca500 040a:0300 Kodak EZ200 zc3xx 041e:041e Creative WebCam Live! +ov519 041e:4003 Video Blaster WebCam Go Plus spca500 041e:400a Creative PC-CAM 300 sunplus 041e:400b Creative PC-CAM 600 sunplus 041e:4012 PC-Cam350 @@ -168,10 +169,14 @@ sunplus 055f:c650 Mustek MDC5500Z zc3xx 055f:d003 Mustek WCam300A zc3xx 055f:d004 Mustek WCam300 AN conex 0572:0041 Creative Notebook cx11646 +ov519 05a9:0511 Video Blaster WebCam 3/WebCam Plus, D-Link USB Digital Video Camera +ov519 05a9:0518 Creative WebCam ov519 05a9:0519 OV519 Microphone ov519 05a9:0530 OmniVision +ov519 05a9:2800 OmniVision SuperCAM ov519 05a9:4519 Webcam Classic ov519 05a9:8519 OmniVision +ov519 05a9:a511 D-Link USB Digital Video Camera ov519 05a9:a518 D-Link DSB-C310 Webcam sunplus 05da:1018 Digital Dream Enigma 1.3 stk014 05e1:0893 Syntek DV4000 @@ -187,7 +192,7 @@ ov534 06f8:3002 Hercules Blog Webcam ov534 06f8:3003 Hercules Dualpix HD Weblog sonixj 06f8:3004 Hercules Classic Silver sonixj 06f8:3008 Hercules Deluxe Optical Glass -pac7311 06f8:3009 Hercules Classic Link +pac7302 06f8:3009 Hercules Classic Link spca508 0733:0110 ViewQuest VQ110 spca501 0733:0401 Intel Create and Share spca501 0733:0402 ViewQuest M318B @@ -199,6 +204,7 @@ sunplus 0733:2221 Mercury Digital Pro 3.1p sunplus 0733:3261 Concord 3045 spca536a sunplus 0733:3281 Cyberpix S550V spca506 0734:043b 3DeMon USB Capture aka +ov519 0813:0002 Dual Mode USB Camera Plus spca500 084d:0003 D-Link DSC-350 spca500 08ca:0103 Aiptek PocketDV sunplus 08ca:0104 Aiptek PocketDVII 1.3 @@ -236,15 +242,15 @@ pac7311 093a:2603 Philips SPC 500 NC pac7311 093a:2608 Trust WB-3300p pac7311 093a:260e Gigaware VGA PC Camera, Trust WB-3350p, SIGMA cam 2350 pac7311 093a:260f SnakeCam -pac7311 093a:2620 Apollo AC-905 -pac7311 093a:2621 PAC731x -pac7311 093a:2622 Genius Eye 312 -pac7311 093a:2624 PAC7302 -pac7311 093a:2626 Labtec 2200 -pac7311 093a:2628 Genius iLook 300 -pac7311 093a:2629 Genious iSlim 300 -pac7311 093a:262a Webcam 300k -pac7311 093a:262c Philips SPC 230 NC +pac7302 093a:2620 Apollo AC-905 +pac7302 093a:2621 PAC731x +pac7302 093a:2622 Genius Eye 312 +pac7302 093a:2624 PAC7302 +pac7302 093a:2626 Labtec 2200 +pac7302 093a:2628 Genius iLook 300 +pac7302 093a:2629 Genious iSlim 300 +pac7302 093a:262a Webcam 300k +pac7302 093a:262c Philips SPC 230 NC jeilinj 0979:0280 Sakar 57379 zc3xx 0ac8:0302 Z-star Vimicro zc0302 vc032x 0ac8:0321 Vimicro generic vc0321 @@ -259,6 +265,7 @@ vc032x 0ac8:c002 Sony embedded vimicro vc032x 0ac8:c301 Samsung Q1 Ultra Premium spca508 0af9:0010 Hama USB Sightcam 100 spca508 0af9:0011 Hama USB Sightcam 100 +ov519 0b62:0059 iBOT2 Webcam sonixb 0c45:6001 Genius VideoCAM NB sonixb 0c45:6005 Microdia Sweex Mini Webcam sonixb 0c45:6007 Sonix sn9c101 + Tas5110D @@ -318,8 +325,10 @@ sn9c20x 0c45:62b3 PC Camera (SN9C202 + OV9655) sn9c20x 0c45:62bb PC Camera (SN9C202 + OV7660) sn9c20x 0c45:62bc PC Camera (SN9C202 + HV7131R) sunplus 0d64:0303 Sunplus FashionCam DXG +ov519 0e96:c001 TRUST 380 USB2 SPACEC@M etoms 102c:6151 Qcam Sangha CIF etoms 102c:6251 Qcam xxxxxx VGA +ov519 1046:9967 W9967CF/W9968CF WebCam IC, Video Blaster WebCam Go zc3xx 10fd:0128 Typhoon Webshot II USB 300k 0x0128 spca561 10fd:7e50 FlyCam Usb 100 zc3xx 10fd:8050 Typhoon Webshot II USB 300k @@ -332,7 +341,12 @@ spca501 1776:501c Arowana 300K CMOS Camera t613 17a1:0128 TASCORP JPEG Webcam, NGS Cyclops vc032x 17ef:4802 Lenovo Vc0323+MI1310_SOC pac207 2001:f115 D-Link DSB-C120 +sq905c 2770:9050 sq905c +sq905c 2770:905c DualCamera +sq905 2770:9120 Argus Digital Camera DC1512 +sq905c 2770:913d sq905c spca500 2899:012c Toptro Industrial +ov519 8020:ef04 ov519 spca508 8086:0110 Intel Easy PC Camera spca500 8086:0630 Intel Pocket PC Camera spca506 99fa:8988 Grandtec V.cap diff --git a/Documentation/video4linux/sh_mobile_ceu_camera.txt b/Documentation/video4linux/sh_mobile_ceu_camera.txt new file mode 100644 index 000000000000..2ae16349a78d --- /dev/null +++ b/Documentation/video4linux/sh_mobile_ceu_camera.txt @@ -0,0 +1,157 @@ + Cropping and Scaling algorithm, used in the sh_mobile_ceu_camera driver + ======================================================================= + +Terminology +----------- + +sensor scales: horizontal and vertical scales, configured by the sensor driver +host scales: -"- host driver +combined scales: sensor_scale * host_scale + + +Generic scaling / cropping scheme +--------------------------------- + +-1-- +| +-2-- -\ +| --\ +| --\ ++-5-- -\ -- -3-- +| ---\ +| --- -4-- -\ +| -\ +| - -6-- +| +| - -6'- +| -/ +| --- -4'- -/ +| ---/ ++-5'- -/ +| -- -3'- +| --/ +| --/ +-2'- -/ +| +| +-1'- + +Produced by user requests: + +S_CROP(left / top = (5) - (1), width / height = (5') - (5)) +S_FMT(width / height = (6') - (6)) + +Here: + +(1) to (1') - whole max width or height +(1) to (2) - sensor cropped left or top +(2) to (2') - sensor cropped width or height +(3) to (3') - sensor scale +(3) to (4) - CEU cropped left or top +(4) to (4') - CEU cropped width or height +(5) to (5') - reverse sensor scale applied to CEU cropped width or height +(2) to (5) - reverse sensor scale applied to CEU cropped left or top +(6) to (6') - CEU scale - user window + + +S_FMT +----- + +Do not touch input rectangle - it is already optimal. + +1. Calculate current sensor scales: + + scale_s = ((3') - (3)) / ((2') - (2)) + +2. Calculate "effective" input crop (sensor subwindow) - CEU crop scaled back at +current sensor scales onto input window - this is user S_CROP: + + width_u = (5') - (5) = ((4') - (4)) * scale_s + +3. Calculate new combined scales from "effective" input window to requested user +window: + + scale_comb = width_u / ((6') - (6)) + +4. Calculate sensor output window by applying combined scales to real input +window: + + width_s_out = ((2') - (2)) / scale_comb + +5. Apply iterative sensor S_FMT for sensor output window. + + subdev->video_ops->s_fmt(.width = width_s_out) + +6. Retrieve sensor output window (g_fmt) + +7. Calculate new sensor scales: + + scale_s_new = ((3')_new - (3)_new) / ((2') - (2)) + +8. Calculate new CEU crop - apply sensor scales to previously calculated +"effective" crop: + + width_ceu = (4')_new - (4)_new = width_u / scale_s_new + left_ceu = (4)_new - (3)_new = ((5) - (2)) / scale_s_new + +9. Use CEU cropping to crop to the new window: + + ceu_crop(.width = width_ceu, .left = left_ceu) + +10. Use CEU scaling to scale to the requested user window: + + scale_ceu = width_ceu / width + + +S_CROP +------ + +If old scale applied to new crop is invalid produce nearest new scale possible + +1. Calculate current combined scales. + + scale_comb = (((4') - (4)) / ((6') - (6))) * (((2') - (2)) / ((3') - (3))) + +2. Apply iterative sensor S_CROP for new input window. + +3. If old combined scales applied to new crop produce an impossible user window, +adjust scales to produce nearest possible window. + + width_u_out = ((5') - (5)) / scale_comb + + if (width_u_out > max) + scale_comb = ((5') - (5)) / max; + else if (width_u_out < min) + scale_comb = ((5') - (5)) / min; + +4. Issue G_CROP to retrieve actual input window. + +5. Using actual input window and calculated combined scales calculate sensor +target output window. + + width_s_out = ((3') - (3)) = ((2') - (2)) / scale_comb + +6. Apply iterative S_FMT for new sensor target output window. + +7. Issue G_FMT to retrieve the actual sensor output window. + +8. Calculate sensor scales. + + scale_s = ((3') - (3)) / ((2') - (2)) + +9. Calculate sensor output subwindow to be cropped on CEU by applying sensor +scales to the requested window. + + width_ceu = ((5') - (5)) / scale_s + +10. Use CEU cropping for above calculated window. + +11. Calculate CEU scales from sensor scales from results of (10) and user window +from (3) + + scale_ceu = calc_scale(((5') - (5)), &width_u_out) + +12. Apply CEU scales. + +-- +Author: Guennadi Liakhovetski <g.liakhovetski@gmx.de> diff --git a/Documentation/video4linux/v4l2-framework.txt b/Documentation/video4linux/v4l2-framework.txt index b806edaf3e75..74d677c8b036 100644 --- a/Documentation/video4linux/v4l2-framework.txt +++ b/Documentation/video4linux/v4l2-framework.txt @@ -561,6 +561,8 @@ video_device helper functions There are a few useful helper functions: +- file/video_device private data + You can set/get driver private data in the video_device struct using: void *video_get_drvdata(struct video_device *vdev); @@ -575,8 +577,7 @@ struct video_device *video_devdata(struct file *file); returns the video_device belonging to the file struct. -The final helper function combines video_get_drvdata with -video_devdata: +The video_drvdata function combines video_get_drvdata with video_devdata: void *video_drvdata(struct file *file); @@ -584,6 +585,17 @@ You can go from a video_device struct to the v4l2_device struct using: struct v4l2_device *v4l2_dev = vdev->v4l2_dev; +- Device node name + +The video_device node kernel name can be retrieved using + +const char *video_device_node_name(struct video_device *vdev); + +The name is used as a hint by userspace tools such as udev. The function +should be used where possible instead of accessing the video_device::num and +video_device::minor fields. + + video buffer helper functions ----------------------------- diff --git a/Documentation/vm/hwpoison.txt b/Documentation/vm/hwpoison.txt index 3ffadf8da61f..12f9ba20ccb7 100644 --- a/Documentation/vm/hwpoison.txt +++ b/Documentation/vm/hwpoison.txt @@ -92,16 +92,62 @@ PR_MCE_KILL_GET Testing: -madvise(MADV_POISON, ....) +madvise(MADV_HWPOISON, ....) (as root) Poison a page in the process for testing hwpoison-inject module through debugfs - /sys/debug/hwpoison/corrupt-pfn -Inject hwpoison fault at PFN echoed into this file +/sys/debug/hwpoison/ +corrupt-pfn + +Inject hwpoison fault at PFN echoed into this file. This does +some early filtering to avoid corrupted unintended pages in test suites. + +unpoison-pfn + +Software-unpoison page at PFN echoed into this file. This +way a page can be reused again. +This only works for Linux injected failures, not for real +memory failures. + +Note these injection interfaces are not stable and might change between +kernel versions + +corrupt-filter-dev-major +corrupt-filter-dev-minor + +Only handle memory failures to pages associated with the file system defined +by block device major/minor. -1U is the wildcard value. +This should be only used for testing with artificial injection. + +corrupt-filter-memcg + +Limit injection to pages owned by memgroup. Specified by inode number +of the memcg. + +Example: + mkdir /cgroup/hwpoison + + usemem -m 100 -s 1000 & + echo `jobs -p` > /cgroup/hwpoison/tasks + + memcg_ino=$(ls -id /cgroup/hwpoison | cut -f1 -d' ') + echo $memcg_ino > /debug/hwpoison/corrupt-filter-memcg + + page-types -p `pidof init` --hwpoison # shall do nothing + page-types -p `pidof usemem` --hwpoison # poison its pages + +corrupt-filter-flags-mask +corrupt-filter-flags-value + +When specified, only poison pages if ((page_flags & mask) == value). +This allows stress testing of many kinds of pages. The page_flags +are the same as in /proc/kpageflags. The flag bits are defined in +include/linux/kernel-page-flags.h and documented in +Documentation/vm/pagemap.txt Architecture specific MCE injector diff --git a/Documentation/vm/page-types.c b/Documentation/vm/page-types.c index 7a7d9bab32ef..66e9358e2144 100644 --- a/Documentation/vm/page-types.c +++ b/Documentation/vm/page-types.c @@ -1,11 +1,22 @@ /* * page-types: Tool for querying page flags * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the Free + * Software Foundation; version 2. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should find a copy of v2 of the GNU General Public License somewhere on + * your Linux system; if not, write to the Free Software Foundation, Inc., 59 + * Temple Place, Suite 330, Boston, MA 02111-1307 USA. + * * Copyright (C) 2009 Intel corporation * * Authors: Wu Fengguang <fengguang.wu@intel.com> - * - * Released under the General Public License (GPL). */ #define _LARGEFILE64_SOURCE |