diff options
Diffstat (limited to 'Documentation/usb/ov511.txt')
-rw-r--r-- | Documentation/usb/ov511.txt | 289 |
1 files changed, 0 insertions, 289 deletions
diff --git a/Documentation/usb/ov511.txt b/Documentation/usb/ov511.txt deleted file mode 100644 index a7fc0432bff1..000000000000 --- a/Documentation/usb/ov511.txt +++ /dev/null @@ -1,289 +0,0 @@ -------------------------------------------------------------------------------- -Readme for Linux device driver for the OmniVision OV511 USB to camera bridge IC -------------------------------------------------------------------------------- - -Author: Mark McClelland -Homepage: http://alpha.dyndns.org/ov511 - -INTRODUCTION: - -This is a driver for the OV511, a USB-only chip used in many "webcam" devices. -Any camera using the OV511/OV511+ and the OV6620/OV7610/20/20AE should work. -Video capture devices that use the Philips SAA7111A decoder also work. It -supports streaming and capture of color or monochrome video via the Video4Linux -API. Most V4L apps are compatible with it. Most resolutions with a width and -height that are a multiple of 8 are supported. - -If you need more information, please visit the OV511 homepage at the above URL. - -WHAT YOU NEED: - -- If you want to help with the development, get the chip's specification docs at - http://www.ovt.com/omniusbp.html - -- A Video4Linux compatible frame grabber program (I recommend vidcat and xawtv) - vidcat is part of the w3cam package: http://mpx.freeshell.net/ - xawtv is available at: http://linux.bytesex.org/xawtv/ - -HOW TO USE IT: - -Note: These are simplified instructions. For complete instructions see: - http://alpha.dyndns.org/ov511/install.html - -You must have first compiled USB support, support for your specific USB host -controller (UHCI or OHCI), and Video4Linux support for your kernel (I recommend -making them modules.) Make sure "Enforce bandwidth allocation" is NOT enabled. - -Next, (as root): - - modprobe usbcore - modprobe usb-uhci <OR> modprobe usb-ohci - modprobe videodev - modprobe ov511 - -If it is not already there (it usually is), create the video device: - - mknod /dev/video0 c 81 0 - -Optionally, symlink /dev/video to /dev/video0 - -You will have to set permissions on this device to allow you to read/write -from it: - - chmod 666 /dev/video - chmod 666 /dev/video0 (if necessary) - -Now you are ready to run a video app! Both vidcat and xawtv work well for me -at 640x480. - -[Using vidcat:] - - vidcat -s 640x480 -p c > test.jpg - xview test.jpg - -[Using xawtv:] - -From the main xawtv directory: - - make clean - ./configure - make - make install - -Now you should be able to run xawtv. Right click for the options dialog. - -MODULE PARAMETERS: - - You can set these with: insmod ov511 NAME=VALUE - There is currently no way to set these on a per-camera basis. - - NAME: autobright - TYPE: integer (Boolean) - DEFAULT: 1 - DESC: Brightness is normally under automatic control and can't be set - manually by the video app. Set to 0 for manual control. - - NAME: autogain - TYPE: integer (Boolean) - DEFAULT: 1 - DESC: Auto Gain Control enable. This feature is not yet implemented. - - NAME: autoexp - TYPE: integer (Boolean) - DEFAULT: 1 - DESC: Auto Exposure Control enable. This feature is not yet implemented. - - NAME: debug - TYPE: integer (0-6) - DEFAULT: 3 - DESC: Sets the threshold for printing debug messages. The higher the value, - the more is printed. The levels are cumulative, and are as follows: - 0=no debug messages - 1=init/detection/unload and other significant messages - 2=some warning messages - 3=config/control function calls - 4=most function calls and data parsing messages - 5=highly repetitive mesgs - - NAME: snapshot - TYPE: integer (Boolean) - DEFAULT: 0 - DESC: Set to 1 to enable snapshot mode. read()/VIDIOCSYNC will block until - the snapshot button is pressed. Note: enabling this mode disables - /proc/video/ov511/<minor#>/button - - NAME: cams - TYPE: integer (1-4 for OV511, 1-31 for OV511+) - DEFAULT: 1 - DESC: Number of cameras allowed to stream simultaneously on a single bus. - Values higher than 1 reduce the data rate of each camera, allowing two - or more to be used at once. If you have a complicated setup involving - both OV511 and OV511+ cameras, trial-and-error may be necessary for - finding the optimum setting. - - NAME: compress - TYPE: integer (Boolean) - DEFAULT: 0 - DESC: Set this to 1 to turn on the camera's compression engine. This can - potentially increase the frame rate at the expense of quality, if you - have a fast CPU. You must load the proper compression module for your - camera before starting your application (ov511_decomp or ov518_decomp). - - NAME: testpat - TYPE: integer (Boolean) - DEFAULT: 0 - DESC: This configures the camera's sensor to transmit a colored test-pattern - instead of an image. This does not work correctly yet. - - NAME: dumppix - TYPE: integer (0-2) - DEFAULT: 0 - DESC: Dumps raw pixel data and skips post-processing and format conversion. - It is for debugging purposes only. Options are: - 0: Disable (default) - 1: Dump raw data from camera, excluding headers and trailers - 2: Dumps data exactly as received from camera - - NAME: led - TYPE: integer (0-2) - DEFAULT: 1 (Always on) - DESC: Controls whether the LED (the little light) on the front of the camera - is always off (0), always on (1), or only on when driver is open (2). - This is not supported with the OV511, and might only work with certain - cameras (ones that actually have the LED wired to the control pin, and - not just hard-wired to be on all the time). - - NAME: dump_bridge - TYPE: integer (Boolean) - DEFAULT: 0 - DESC: Dumps the bridge (OV511[+] or OV518[+]) register values to the system - log. Only useful for serious debugging/development purposes. - - NAME: dump_sensor - TYPE: integer (Boolean) - DEFAULT: 0 - DESC: Dumps the sensor register values to the system log. Only useful for - serious debugging/development purposes. - - NAME: printph - TYPE: integer (Boolean) - DEFAULT: 0 - DESC: Setting this to 1 will dump the first 12 bytes of each isoc frame. This - is only useful if you are trying to debug problems with the isoc data - stream (i.e.: camera initializes, but vidcat hangs until Ctrl-C). Be - warned that this dumps a large number of messages to your kernel log. - - NAME: phy, phuv, pvy, pvuv, qhy, qhuv, qvy, qvuv - TYPE: integer (0-63 for phy and phuv, 0-255 for rest) - DEFAULT: OV511 default values - DESC: These are registers 70h - 77h of the OV511, which control the - prediction ranges and quantization thresholds of the compressor, for - the Y and UV channels in the horizontal and vertical directions. See - the OV511 or OV511+ data sheet for more detailed descriptions. These - normally do not need to be changed. - - NAME: lightfreq - TYPE: integer (0, 50, or 60) - DEFAULT: 0 (use sensor default) - DESC: Sets the sensor to match your lighting frequency. This can reduce the - appearance of "banding", i.e. horizontal lines or waves of light and - dark that are often caused by artificial lighting. Valid values are: - 0 - Use default (depends on sensor, most likely 60 Hz) - 50 - For European and Asian 50 Hz power - 60 - For American 60 Hz power - - NAME: bandingfilter - TYPE: integer (Boolean) - DEFAULT: 0 (off) - DESC: Enables the sensorīs banding filter exposure algorithm. This reduces - or stabilizes the "banding" caused by some artificial light sources - (especially fluorescent). You might have to set lightfreq correctly for - this to work right. As an added bonus, this sometimes makes it - possible to capture your monitorīs output. - - NAME: fastset - TYPE: integer (Boolean) - DEFAULT: 0 (off) - DESC: Allows picture settings (brightness, contrast, color, and hue) to take - effect immediately, even in the middle of a frame. This reduces the - time to change settings, but can ruin frames during the change. Only - affects OmniVision sensors. - - NAME: force_palette - TYPE: integer (Boolean) - DEFAULT: 0 (off) - DESC: Forces the palette (color format) to a specific value. If an - application requests a different palette, it will be rejected, thereby - forcing it to try others until it succeeds. This is useful for forcing - greyscale mode with a color camera, for example. Supported modes are: - 0 (Allows all the following formats) - 1 VIDEO_PALETTE_GREY (Linear greyscale) - 10 VIDEO_PALETTE_YUV420 (YUV 4:2:0 Planar) - 15 VIDEO_PALETTE_YUV420P (YUV 4:2:0 Planar, same as 10) - - NAME: backlight - TYPE: integer (Boolean) - DEFAULT: 0 (off) - DESC: Setting this flag changes the exposure algorithm for OmniVision sensors - such that objects in the camera's view (i.e. your head) can be clearly - seen when they are illuminated from behind. It reduces or eliminates - the sensor's auto-exposure function, so it should only be used when - needed. Additionally, it is only supported with the OV6620 and OV7620. - - NAME: unit_video - TYPE: Up to 16 comma-separated integers - DEFAULT: 0,0,0... (automatically assign the next available minor(s)) - DESC: You can specify up to 16 minor numbers to be assigned to ov511 devices. - For example, "unit_video=1,3" will make the driver use /dev/video1 and - /dev/video3 for the first two devices it detects. Additional devices - will be assigned automatically starting at the first available device - node (/dev/video0 in this case). Note that you cannot specify 0 as a - minor number. This feature requires kernel version 2.4.5 or higher. - - NAME: remove_zeros - TYPE: integer (Boolean) - DEFAULT: 0 (do not skip any incoming data) - DESC: Setting this to 1 will remove zero-padding from incoming data. This - will compensate for the blocks of corruption that can appear when the - camera cannot keep up with the speed of the USB bus (eg. at low frame - resolutions). This feature is always enabled when compression is on. - - NAME: mirror - TYPE: integer (Boolean) - DEFAULT: 0 (off) - DESC: Setting this to 1 will reverse ("mirror") the image horizontally. This - might be necessary if your camera has a custom lens assembly. This has - no effect with video capture devices. - - NAME: ov518_color - TYPE: integer (Boolean) - DEFAULT: 0 (off) - DESC: Enable OV518 color support. This is off by default since it doesn't - work most of the time. If you want to try it, you must also load - ov518_decomp with the "nouv=0" parameter. If you get improper colors or - diagonal lines through the image, restart your video app and try again. - Repeat as necessary. - -WORKING FEATURES: - o Color streaming/capture at most widths and heights that are multiples of 8. - o Monochrome (use force_palette=1 to enable) - o Setting/getting of saturation, contrast, brightness, and hue (only some of - them work the OV7620 and OV7620AE) - o /proc status reporting - o SAA7111A video capture support at 320x240 and 640x480 - o Compression support - o SMP compatibility - -HOW TO CONTACT ME: - -You can email me at mark@alpha.dyndns.org . Please prefix the subject line -with "OV511: " so that I am certain to notice your message. - -CREDITS: - -The code is based in no small part on the CPiA driver by Johannes Erdfelt, -Randy Dunlap, and others. Big thanks to them for their pioneering work on that -and the USB stack. Thanks to Bret Wallach for getting camera reg IO, ISOC, and -image capture working. Thanks to Orion Sky Lawlor, Kevin Moore, and Claudio -Matsuoka for their work as well. - |