diff options
Diffstat (limited to 'Documentation/powerpc/booting-without-of.txt')
| -rw-r--r-- | Documentation/powerpc/booting-without-of.txt | 142 |
1 files changed, 100 insertions, 42 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt index de2e5c05d6e7..07ae2edff7c4 100644 --- a/Documentation/powerpc/booting-without-of.txt +++ b/Documentation/powerpc/booting-without-of.txt @@ -77,10 +77,12 @@ Table of Contents 3) OpenPIC Interrupt Controllers 4) ISA Interrupt Controllers - VIII - Specifying GPIO information for devices + IX - Specifying GPIO information for devices 1) gpios property 2) gpio-controller nodes + X - Specifying device power management information (sleep property) + Appendix A - Sample SOC node for MPC8540 @@ -2422,8 +2424,8 @@ encodings listed below: 2 = high to low edge sensitive type enabled 3 = low to high edge sensitive type enabled -VIII - Specifying GPIO information for devices -============================================== +IX - Specifying GPIO information for devices +============================================ 1) gpios property ----------------- @@ -2471,6 +2473,37 @@ Example of two SOC GPIO banks defined as gpio-controller nodes: gpio-controller; }; +X - Specifying Device Power Management Information (sleep property) +=================================================================== + +Devices on SOCs often have mechanisms for placing devices into low-power +states that are decoupled from the devices' own register blocks. Sometimes, +this information is more complicated than a cell-index property can +reasonably describe. Thus, each device controlled in such a manner +may contain a "sleep" property which describes these connections. + +The sleep property consists of one or more sleep resources, each of +which consists of a phandle to a sleep controller, followed by a +controller-specific sleep specifier of zero or more cells. + +The semantics of what type of low power modes are possible are defined +by the sleep controller. Some examples of the types of low power modes +that may be supported are: + + - Dynamic: The device may be disabled or enabled at any time. + - System Suspend: The device may request to be disabled or remain + awake during system suspend, but will not be disabled until then. + - Permanent: The device is disabled permanently (until the next hard + reset). + +Some devices may share a clock domain with each other, such that they should +only be suspended when none of the devices are in use. Where reasonable, +such nodes should be placed on a virtual bus, where the bus has the sleep +property. If the clock domain is shared among devices that cannot be +reasonably grouped in this manner, then create a virtual sleep controller +(similar to an interrupt nexus, except that defining a standardized +sleep-map should wait until its necessity is demonstrated). + Appendix A - Sample SOC node for MPC8540 ======================================== @@ -2487,47 +2520,48 @@ not necessary as they are usually the same as the root node. reg = <e0000000 00003000>; bus-frequency = <0>; - mdio@24520 { - reg = <24520 20>; - device_type = "mdio"; - compatible = "gianfar"; - - ethernet-phy@0 { - linux,phandle = <2452000> - interrupt-parent = <40000>; - interrupts = <35 1>; - reg = <0>; - device_type = "ethernet-phy"; - }; - - ethernet-phy@1 { - linux,phandle = <2452001> - interrupt-parent = <40000>; - interrupts = <35 1>; - reg = <1>; - device_type = "ethernet-phy"; - }; - - ethernet-phy@3 { - linux,phandle = <2452002> - interrupt-parent = <40000>; - interrupts = <35 1>; - reg = <3>; - device_type = "ethernet-phy"; - }; - - }; - ethernet@24000 { - #size-cells = <0>; + #address-cells = <1>; + #size-cells = <1>; device_type = "network"; model = "TSEC"; - compatible = "gianfar"; + compatible = "gianfar", "simple-bus"; reg = <24000 1000>; mac-address = [ 00 E0 0C 00 73 00 ]; interrupts = <d 3 e 3 12 3>; interrupt-parent = <40000>; phy-handle = <2452000>; + sleep = <&pmc 00000080>; + ranges; + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + linux,phandle = <2452000> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <0>; + device_type = "ethernet-phy"; + }; + + ethernet-phy@1 { + linux,phandle = <2452001> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <1>; + device_type = "ethernet-phy"; + }; + + ethernet-phy@3 { + linux,phandle = <2452002> + interrupt-parent = <40000>; + interrupts = <35 1>; + reg = <3>; + device_type = "ethernet-phy"; + }; + }; }; ethernet@25000 { @@ -2541,6 +2575,7 @@ not necessary as they are usually the same as the root node. interrupts = <13 3 14 3 18 3>; interrupt-parent = <40000>; phy-handle = <2452001>; + sleep = <&pmc 00000040>; }; ethernet@26000 { @@ -2554,15 +2589,33 @@ not necessary as they are usually the same as the root node. interrupts = <19 3>; interrupt-parent = <40000>; phy-handle = <2452002>; + sleep = <&pmc 00000020>; }; serial@4500 { - device_type = "serial"; - compatible = "ns16550"; - reg = <4500 100>; - clock-frequency = <0>; - interrupts = <1a 3>; - interrupt-parent = <40000>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8540-duart", "simple-bus"; + sleep = <&pmc 00000002>; + ranges; + + serial@4500 { + device_type = "serial"; + compatible = "ns16550"; + reg = <4500 100>; + clock-frequency = <0>; + interrupts = <1a 3>; + interrupt-parent = <40000>; + }; + + serial@4600 { + device_type = "serial"; + compatible = "ns16550"; + reg = <4600 100>; + clock-frequency = <0>; + interrupts = <1a 3>; + interrupt-parent = <40000>; + }; }; pic@40000 { @@ -2581,6 +2634,11 @@ not necessary as they are usually the same as the root node. device_type = "i2c"; compatible = "fsl-i2c"; dfsrr; + sleep = <&pmc 00000004>; }; + pmc: power@e0070 { + compatible = "fsl,mpc8540-pmc", "fsl,mpc8548-pmc"; + reg = <e0070 20>; + }; }; |