diff options
Diffstat (limited to 'Documentation/networking')
| -rw-r--r-- | Documentation/networking/device_drivers/aquantia/atlantic.txt | 46 | ||||
| -rw-r--r-- | Documentation/networking/device_drivers/freescale/dpaa.txt | 12 | ||||
| -rw-r--r-- | Documentation/networking/device_drivers/mellanox/mlx5.rst | 21 | ||||
| -rw-r--r-- | Documentation/networking/device_drivers/ti/cpsw_switchdev.txt | 209 | ||||
| -rw-r--r-- | Documentation/networking/devlink-params-mlx5.txt | 17 | ||||
| -rw-r--r-- | Documentation/networking/devlink-params-ti-cpsw-switch.txt | 10 | ||||
| -rw-r--r-- | Documentation/networking/devlink-params.txt | 4 | ||||
| -rw-r--r-- | Documentation/networking/devlink-trap.rst | 61 | ||||
| -rw-r--r-- | Documentation/networking/ip-sysctl.txt | 34 | ||||
| -rw-r--r-- | Documentation/networking/tls-offload.rst | 4 |
10 files changed, 409 insertions, 9 deletions
diff --git a/Documentation/networking/device_drivers/aquantia/atlantic.txt b/Documentation/networking/device_drivers/aquantia/atlantic.txt index d235cbaeccc6..2013fcedc2da 100644 --- a/Documentation/networking/device_drivers/aquantia/atlantic.txt +++ b/Documentation/networking/device_drivers/aquantia/atlantic.txt @@ -1,5 +1,5 @@ -aQuantia AQtion Driver for the aQuantia Multi-Gigabit PCI Express Family of -Ethernet Adapters +Marvell(Aquantia) AQtion Driver for the aQuantia Multi-Gigabit PCI Express +Family of Ethernet Adapters ============================================================================= Contents @@ -325,6 +325,46 @@ Supported ethtool options Example: ethtool -N eth0 flow-type udp4 action 0 loc 32 + UDP GSO hardware offload + --------------------------------- + UDP GSO allows to boost UDP tx rates by offloading UDP headers allocation + into hardware. A special userspace socket option is required for this, + could be validated with /kernel/tools/testing/selftests/net/ + + udpgso_bench_tx -u -4 -D 10.0.1.1 -s 6300 -S 100 + + Will cause sending out of 100 byte sized UDP packets formed from single + 6300 bytes user buffer. + + UDP GSO is configured by: + + ethtool -K eth0 tx-udp-segmentation on + + Private flags (testing) + --------------------------------- + + Atlantic driver supports private flags for hardware custom features: + + $ ethtool --show-priv-flags ethX + + Private flags for ethX: + DMASystemLoopback : off + PKTSystemLoopback : off + DMANetworkLoopback : off + PHYInternalLoopback: off + PHYExternalLoopback: off + + Example: + + $ ethtool --set-priv-flags ethX DMASystemLoopback on + + DMASystemLoopback: DMA Host loopback. + PKTSystemLoopback: Packet buffer host loopback. + DMANetworkLoopback: Network side loopback on DMA block. + PHYInternalLoopback: Internal loopback on Phy. + PHYExternalLoopback: External loopback on Phy (with loopback ethernet cable). + + Command Line Parameters ======================= The following command line parameters are available on atlantic driver: @@ -426,7 +466,7 @@ Support If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information related -to the issue to support@aquantia.com +to the issue to aqn_support@marvell.com License ======= diff --git a/Documentation/networking/device_drivers/freescale/dpaa.txt b/Documentation/networking/device_drivers/freescale/dpaa.txt index f88194f71c54..b06601ff9200 100644 --- a/Documentation/networking/device_drivers/freescale/dpaa.txt +++ b/Documentation/networking/device_drivers/freescale/dpaa.txt @@ -129,9 +129,9 @@ CONFIG_AQUANTIA_PHY=y DPAA Ethernet Frame Processing ============================== -On Rx, buffers for the incoming frames are retrieved from one of the three -existing buffers pools. The driver initializes and seeds these, each with -buffers of different sizes: 1KB, 2KB and 4KB. +On Rx, buffers for the incoming frames are retrieved from the buffers found +in the dedicated interface buffer pool. The driver initializes and seeds these +with one page buffers. On Tx, all transmitted frames are returned to the driver through Tx confirmation frame queues. The driver is then responsible for freeing the @@ -254,7 +254,7 @@ The following statistics are exported for each interface through ethtool: The driver also exports the following information in sysfs: - the FQ IDs for each FQ type - /sys/devices/platform/dpaa-ethernet.0/net/<int>/fqids + /sys/devices/platform/soc/<addr>.fman/<addr>.ethernet/dpaa-ethernet.<id>/net/fm<nr>-mac<nr>/fqids - - the IDs of the buffer pools in use - /sys/devices/platform/dpaa-ethernet.0/net/<int>/bpids + - the ID of the buffer pool in use + /sys/devices/platform/soc/<addr>.fman/<addr>.ethernet/dpaa-ethernet.<id>/net/fm<nr>-mac<nr>/bpids diff --git a/Documentation/networking/device_drivers/mellanox/mlx5.rst b/Documentation/networking/device_drivers/mellanox/mlx5.rst index d071c6b49e1f..7599dceba9f1 100644 --- a/Documentation/networking/device_drivers/mellanox/mlx5.rst +++ b/Documentation/networking/device_drivers/mellanox/mlx5.rst @@ -154,6 +154,27 @@ User command examples: values: cmode runtime value smfs +enable_roce: RoCE enablement state +---------------------------------- +RoCE enablement state controls driver support for RoCE traffic. +When RoCE is disabled, there is no gid table, only raw ethernet QPs are supported and traffic on the well known UDP RoCE port is handled as raw ethernet traffic. + +To change RoCE enablement state a user must change the driverinit cmode value and run devlink reload. + +User command examples: + +- Disable RoCE:: + + $ devlink dev param set pci/0000:06:00.0 name enable_roce value false cmode driverinit + $ devlink dev reload pci/0000:06:00.0 + +- Read RoCE enablement state:: + + $ devlink dev param show pci/0000:06:00.0 name enable_roce + pci/0000:06:00.0: + name enable_roce type generic + values: + cmode driverinit value true Devlink health reporters ======================== diff --git a/Documentation/networking/device_drivers/ti/cpsw_switchdev.txt b/Documentation/networking/device_drivers/ti/cpsw_switchdev.txt new file mode 100644 index 000000000000..5c8cee17fca9 --- /dev/null +++ b/Documentation/networking/device_drivers/ti/cpsw_switchdev.txt @@ -0,0 +1,209 @@ +* Texas Instruments CPSW switchdev based ethernet driver 2.0 + +- Port renaming +On older udev versions renaming of ethX to swXpY will not be automatically +supported +In order to rename via udev: +ip -d link show dev sw0p1 | grep switchid + +SUBSYSTEM=="net", ACTION=="add", ATTR{phys_switch_id}==<switchid>, \ + ATTR{phys_port_name}!="", NAME="sw0$attr{phys_port_name}" + + +==================== +# Dual mac mode +==================== +- The new (cpsw_new.c) driver is operating in dual-emac mode by default, thus +working as 2 individual network interfaces. Main differences from legacy CPSW +driver are: + - optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in +addition to ALLMULTI (current port) instead of ALE_BYPASS. +So, Ports in promiscuous mode will keep possibility of mcast and vlan filtering, +which is provides significant benefits when ports are joined to the same bridge, +but without enabling "switch" mode, or to different bridges. + - learning disabled on ports as it make not too much sense for + segregated ports - no forwarding in HW. + - enabled basic support for devlink. + + devlink dev show + platform/48484000.switch + + devlink dev param show + platform/48484000.switch: + name switch_mode type driver-specific + values: + cmode runtime value false + name ale_bypass type driver-specific + values: + cmode runtime value false + +Devlink configuration parameters +==================== +See Documentation/networking/devlink-params-ti-cpsw-switch.txt + +==================== +# Bridging in dual mac mode +==================== +The dual_mac mode requires two vids to be reserved for internal purposes, +which, by default, equal CPSW Port numbers. As result, bridge has to be +configured in vlan unaware mode or default_pvid has to be adjusted. + + ip link add name br0 type bridge + ip link set dev br0 type bridge vlan_filtering 0 + echo 0 > /sys/class/net/br0/bridge/default_pvid + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + - or - + ip link add name br0 type bridge + ip link set dev br0 type bridge vlan_filtering 0 + echo 100 > /sys/class/net/br0/bridge/default_pvid + ip link set dev br0 type bridge vlan_filtering 1 + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + +==================== +# Enabling "switch" +==================== +The Switch mode can be enabled by configuring devlink driver parameter +"switch_mode" to 1/true: + devlink dev param set platform/48484000.switch \ + name switch_mode value 1 cmode runtime + +This can be done regardless of the state of Port's netdev devices - UP/DOWN, but +Port's netdev devices have to be in UP before joining to the bridge to avoid +overwriting of bridge configuration as CPSW switch driver copletly reloads its +configuration when first Port changes its state to UP. + +When the both interfaces joined the bridge - CPSW switch driver will enable +marking packets with offload_fwd_mark flag unless "ale_bypass=0" + +All configuration is implemented via switchdev API. + +==================== +# Bridge setup +==================== + devlink dev param set platform/48484000.switch \ + name switch_mode value 1 cmode runtime + + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p1 master br0 + ip link set dev sw0p2 master br0 + [*] bridge vlan add dev br0 vid 1 pvid untagged self + +[*] if vlan_filtering=1. where default_pvid=1 + +================= +# On/off STP +================= +ip link set dev BRDEV type bridge stp_state 1/0 + +Note. Steps [*] are mandatory. + +==================== +# VLAN configuration +==================== +bridge vlan add dev br0 vid 1 pvid untagged self <---- add cpu port to VLAN 1 + +Note. This step is mandatory for bridge/default_pvid. + +================= +# Add extra VLANs +================= + 1. untagged: + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 pvid untagged master + bridge vlan add dev br0 vid 100 pvid untagged self <---- Add cpu port to VLAN100 + + 2. tagged: + bridge vlan add dev sw0p1 vid 100 master + bridge vlan add dev sw0p2 vid 100 master + bridge vlan add dev br0 vid 100 pvid tagged self <---- Add cpu port to VLAN100 + +==== +FDBs +==== +FDBs are automatically added on the appropriate switch port upon detection + +Manually adding FDBs: +bridge fdb add aa:bb:cc:dd:ee:ff dev sw0p1 master vlan 100 +bridge fdb add aa:bb:cc:dd:ee:fe dev sw0p2 master <---- Add on all VLANs + +==== +MDBs +==== +MDBs are automatically added on the appropriate switch port upon detection + +Manually adding MDBs: +bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent vid 100 +bridge mdb add dev br0 port sw0p1 grp 239.1.1.1 permanent <---- Add on all VLANs + +================== +Multicast flooding +================== +CPU port mcast_flooding is always on + +Turning flooding on/off on swithch ports: +bridge link set dev sw0p1 mcast_flood on/off + +================== +Access and Trunk port +================== + bridge vlan add dev sw0p1 vid 100 pvid untagged master + bridge vlan add dev sw0p2 vid 100 master + + + bridge vlan add dev br0 vid 100 self + ip link add link br0 name br0.100 type vlan id 100 + + Note. Setting PVID on Bridge device itself working only for + default VLAN (default_pvid). + +===================== + NFS +===================== +The only way for NFS to work is by chrooting to a minimal environment when +switch configuration that will affect connectivity is needed. +Assuming you are booting NFS with eth1 interface(the script is hacky and +it's just there to prove NFS is doable). + +setup.sh: +#!/bin/sh +mkdir proc +mount -t proc none /proc +ifconfig br0 > /dev/null +if [ $? -ne 0 ]; then + echo "Setting up bridge" + ip link add name br0 type bridge + ip link set dev br0 type bridge ageing_time 1000 + ip link set dev br0 type bridge vlan_filtering 1 + + ip link set eth1 down + ip link set eth1 name sw0p1 + ip link set dev sw0p1 up + ip link set dev sw0p2 up + ip link set dev sw0p2 master br0 + ip link set dev sw0p1 master br0 + bridge vlan add dev br0 vid 1 pvid untagged self + ifconfig sw0p1 0.0.0.0 + udhchc -i br0 +fi +umount /proc + +run_nfs.sh: +#!/bin/sh +mkdir /tmp/root/bin -p +mkdir /tmp/root/lib -p + +cp -r /lib/ /tmp/root/ +cp -r /bin/ /tmp/root/ +cp /sbin/ip /tmp/root/bin +cp /sbin/bridge /tmp/root/bin +cp /sbin/ifconfig /tmp/root/bin +cp /sbin/udhcpc /tmp/root/bin +cp /path/to/setup.sh /tmp/root/bin +chroot /tmp/root/ busybox sh /bin/setup.sh + +run ./run_nfs.sh diff --git a/Documentation/networking/devlink-params-mlx5.txt b/Documentation/networking/devlink-params-mlx5.txt new file mode 100644 index 000000000000..5071467118bd --- /dev/null +++ b/Documentation/networking/devlink-params-mlx5.txt @@ -0,0 +1,17 @@ +flow_steering_mode [DEVICE, DRIVER-SPECIFIC] + Controls the flow steering mode of the driver. + Two modes are supported: + 1. 'dmfs' - Device managed flow steering. + 2. 'smfs - Software/Driver managed flow steering. + In DMFS mode, the HW steering entities are created and + managed through the Firmware. + In SMFS mode, the HW steering entities are created and + managed though by the driver directly into Hardware + without firmware intervention. + Type: String + Configuration mode: runtime + +enable_roce [DEVICE, GENERIC] + Enable handling of RoCE traffic in the device. + Defaultly enabled. + Configuration mode: driverinit diff --git a/Documentation/networking/devlink-params-ti-cpsw-switch.txt b/Documentation/networking/devlink-params-ti-cpsw-switch.txt new file mode 100644 index 000000000000..4037458499f7 --- /dev/null +++ b/Documentation/networking/devlink-params-ti-cpsw-switch.txt @@ -0,0 +1,10 @@ +ale_bypass [DEVICE, DRIVER-SPECIFIC] + Allows to enable ALE_CONTROL(4).BYPASS mode for debug purposes. + All packets will be sent to the Host port only if enabled. + Type: bool + Configuration mode: runtime + +switch_mode [DEVICE, DRIVER-SPECIFIC] + Enable switch mode + Type: bool + Configuration mode: runtime diff --git a/Documentation/networking/devlink-params.txt b/Documentation/networking/devlink-params.txt index ddba3e9b55b1..04e234e9acc9 100644 --- a/Documentation/networking/devlink-params.txt +++ b/Documentation/networking/devlink-params.txt @@ -65,3 +65,7 @@ reset_dev_on_drv_probe [DEVICE, GENERIC] Reset only if device firmware can be found in the filesystem. Type: u8 + +enable_roce [DEVICE, GENERIC] + Enable handling of RoCE traffic in the device. + Type: Boolean diff --git a/Documentation/networking/devlink-trap.rst b/Documentation/networking/devlink-trap.rst index 8e90a85f3bd5..dc9659ca06fa 100644 --- a/Documentation/networking/devlink-trap.rst +++ b/Documentation/networking/devlink-trap.rst @@ -162,6 +162,67 @@ be added to the following table: - ``drop`` - Traps packets that the device decided to drop because they could not be enqueued to a transmission queue which is full + * - ``non_ip`` + - ``drop`` + - Traps packets that the device decided to drop because they need to + undergo a layer 3 lookup, but are not IP or MPLS packets + * - ``uc_dip_over_mc_dmac`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and they have a unicast destination IP and a multicast destination + MAC + * - ``dip_is_loopback_address`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their destination IP is the loopback address (i.e., 127.0.0.0/8 + and ::1/128) + * - ``sip_is_mc`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their source IP is multicast (i.e., 224.0.0.0/8 and ff::/8) + * - ``sip_is_loopback_address`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their source IP is the loopback address (i.e., 127.0.0.0/8 and ::1/128) + * - ``ip_header_corrupted`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their IP header is corrupted: wrong checksum, wrong IP version + or too short Internet Header Length (IHL) + * - ``ipv4_sip_is_limited_bc`` + - ``drop`` + - Traps packets that the device decided to drop because they need to be + routed and their source IP is limited broadcast (i.e., 255.255.255.255/32) + * - ``ipv6_mc_dip_reserved_scope`` + - ``drop`` + - Traps IPv6 packets that the device decided to drop because they need to + be routed and their IPv6 multicast destination IP has a reserved scope + (i.e., ffx0::/16) + * - ``ipv6_mc_dip_interface_local_scope`` + - ``drop`` + - Traps IPv6 packets that the device decided to drop because they need to + be routed and their IPv6 multicast destination IP has an interface-local scope + (i.e., ffx1::/16) + * - ``mtu_value_is_too_small`` + - ``exception`` + - Traps packets that should have been routed by the device, but were bigger + than the MTU of the egress interface + * - ``unresolved_neigh`` + - ``exception`` + - Traps packets that did not have a matching IP neighbour after routing + * - ``mc_reverse_path_forwarding`` + - ``exception`` + - Traps multicast IP packets that failed reverse-path forwarding (RPF) + check during multicast routing + * - ``reject_route`` + - ``exception`` + - Traps packets that hit reject routes (i.e., "unreachable", "prohibit") + * - ``ipv4_lpm_miss`` + - ``exception`` + - Traps unicast IPv4 packets that did not match any route + * - ``ipv6_lpm_miss`` + - ``exception`` + - Traps unicast IPv6 packets that did not match any route Driver-specific Packet Traps ============================ diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index 8d4ad1d1ae26..099a55bd1432 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -2091,6 +2091,28 @@ pf_enable - INTEGER Default: 1 +pf_expose - INTEGER + Unset or enable/disable pf (pf is short for potentially failed) state + exposure. Applications can control the exposure of the PF path state + in the SCTP_PEER_ADDR_CHANGE event and the SCTP_GET_PEER_ADDR_INFO + sockopt. When it's unset, no SCTP_PEER_ADDR_CHANGE event with + SCTP_ADDR_PF state will be sent and a SCTP_PF-state transport info + can be got via SCTP_GET_PEER_ADDR_INFO sockopt; When it's enabled, + a SCTP_PEER_ADDR_CHANGE event will be sent for a transport becoming + SCTP_PF state and a SCTP_PF-state transport info can be got via + SCTP_GET_PEER_ADDR_INFO sockopt; When it's diabled, no + SCTP_PEER_ADDR_CHANGE event will be sent and it returns -EACCES when + trying to get a SCTP_PF-state transport info via SCTP_GET_PEER_ADDR_INFO + sockopt. + + 0: Unset pf state exposure, Compatible with old applications. + + 1: Disable pf state exposure. + + 2: Enable pf state exposure. + + Default: 0 + addip_noauth_enable - BOOLEAN Dynamic Address Reconfiguration (ADD-IP) requires the use of authentication to protect the operations of adding or removing new @@ -2173,6 +2195,18 @@ pf_retrans - INTEGER Default: 0 +ps_retrans - INTEGER + Primary.Switchover.Max.Retrans (PSMR), it's a tunable parameter coming + from section-5 "Primary Path Switchover" in rfc7829. The primary path + will be changed to another active path when the path error counter on + the old primary path exceeds PSMR, so that "the SCTP sender is allowed + to continue data transmission on a new working path even when the old + primary destination address becomes active again". Note this feature + is disabled by initializing 'ps_retrans' per netns as 0xffff by default, + and its value can't be less than 'pf_retrans' when changing by sysctl. + + Default: 0xffff + rto_initial - INTEGER The initial round trip timeout value in milliseconds that will be used in calculating round trip times. This is the initial time interval diff --git a/Documentation/networking/tls-offload.rst b/Documentation/networking/tls-offload.rst index 0dd3f748239f..f914e81fd3a6 100644 --- a/Documentation/networking/tls-offload.rst +++ b/Documentation/networking/tls-offload.rst @@ -436,6 +436,10 @@ by the driver: encryption. * ``tx_tls_ooo`` - number of TX packets which were part of a TLS stream but did not arrive in the expected order. + * ``tx_tls_skip_no_sync_data`` - number of TX packets which were part of + a TLS stream and arrived out-of-order, but skipped the HW offload routine + and went to the regular transmit flow as they were retransmissions of the + connection handshake. * ``tx_tls_drop_no_sync_data`` - number of TX packets which were part of a TLS stream dropped, because they arrived out of order and associated record could not be found. |