diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 69 |
1 files changed, 60 insertions, 9 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index a2d8805c03d5..532eacbbed62 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -91,6 +91,7 @@ parameter is applicable: SUSPEND System suspend states are enabled. FTRACE Function tracing enabled. TS Appropriate touchscreen support is enabled. + UMS USB Mass Storage support is enabled. USB USB support is enabled. USBHID USB Human Interface Device support is enabled. V4L Video For Linux support is enabled. @@ -469,8 +470,8 @@ and is between 256 and 4096 characters. It is defined in the file clearcpuid=BITNUM [X86] Disable CPUID feature X for the kernel. See - include/asm-x86/cpufeature.h for the valid bit numbers. - Note the Linux specific bits are not necessarily + arch/x86/include/asm/cpufeature.h for the valid bit + numbers. Note the Linux specific bits are not necessarily stable over kernel options, but the vendor specific ones should be. Also note that user programs calling CPUID directly @@ -551,6 +552,11 @@ and is between 256 and 4096 characters. It is defined in the file not work reliably with all consoles, but is known to work with serial and VGA consoles. + coredump_filter= + [KNL] Change the default value for + /proc/<pid>/coredump_filter. + See also Documentation/filesystems/proc.txt. + cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver Format: <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>] @@ -913,6 +919,10 @@ and is between 256 and 4096 characters. It is defined in the file inttest= [IA64] + iomem= Disable strict checking of access to MMIO memory + strict regions from userspace. + relaxed + iommu= [x86] off force @@ -1117,6 +1127,8 @@ and is between 256 and 4096 characters. It is defined in the file If there are multiple matching configurations changing the same attribute, the last one is used. + lmb=debug [KNL] Enable lmb debug messages. + load_ramdisk= [RAM] List of ramdisks to load from floppy See Documentation/blockdev/ramdisk.txt. @@ -1569,6 +1581,10 @@ and is between 256 and 4096 characters. It is defined in the file nr_uarts= [SERIAL] maximum number of UARTs to be registered. + ohci1394_dma=early [HW] enable debugging via the ohci1394 driver. + See Documentation/debugging-via-ohci1394.txt for more + info. + olpc_ec_timeout= [OLPC] ms delay when issuing EC commands Rather than timing out after 20 ms if an EC command is not properly ACKed, override the length @@ -1793,10 +1809,10 @@ and is between 256 and 4096 characters. It is defined in the file autoconfiguration. Ranges are in pairs (memory base and size). - dynamic_printk - Enables pr_debug()/dev_dbg() calls if - CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also - be switched on/off via <debugfs>/dynamic_printk/modules + dynamic_printk Enables pr_debug()/dev_dbg() calls if + CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. + These can also be switched on/off via + <debugfs>/dynamic_printk/modules print-fatal-signals= [KNL] debug: print fatal signals @@ -1884,7 +1900,7 @@ and is between 256 and 4096 characters. It is defined in the file reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode Format: <reboot_mode>[,<reboot_mode2>[,...]] - See arch/*/kernel/reboot.c or arch/*/kernel/process.c + See arch/*/kernel/reboot.c or arch/*/kernel/process.c relax_domain_level= [KNL, SMP] Set scheduler's default relax_domain_level. @@ -2372,6 +2388,41 @@ and is between 256 and 4096 characters. It is defined in the file usbhid.mousepoll= [USBHID] The interval which mice are to be polled at. + usb-storage.delay_use= + [UMS] The delay in seconds before a new device is + scanned for Logical Units (default 5). + + usb-storage.quirks= + [UMS] A list of quirks entries to supplement or + override the built-in unusual_devs list. List + entries are separated by commas. Each entry has + the form VID:PID:Flags where VID and PID are Vendor + and Product ID values (4-digit hex numbers) and + Flags is a set of characters, each corresponding + to a common usb-storage quirk flag as follows: + a = SANE_SENSE (collect more than 18 bytes + of sense data); + c = FIX_CAPACITY (decrease the reported + device capacity by one sector); + h = CAPACITY_HEURISTICS (decrease the + reported device capacity by one + sector if the number is odd); + i = IGNORE_DEVICE (don't bind to this + device); + l = NOT_LOCKABLE (don't try to lock and + unlock ejectable media); + m = MAX_SECTORS_64 (don't transfer more + than 64 sectors = 32 KB at a time); + o = CAPACITY_OK (accept the capacity + reported by the device); + r = IGNORE_RESIDUE (the device reports + bogus residue values); + s = SINGLE_LUN (the device has only one + Logical Unit); + w = NO_WP_DETECT (don't test whether the + medium is write-protected). + Example: quirks=0419:aaf5:rl,0421:0433:rc + add_efi_memmap [EFI; x86-32,X86-64] Include EFI memory map in kernel's map of available physical RAM. @@ -2432,8 +2483,8 @@ and is between 256 and 4096 characters. It is defined in the file Format: <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]] - norandmaps Don't use address space randomization - Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space + norandmaps Don't use address space randomization. Equivalent to + echo 0 > /proc/sys/kernel/randomize_va_space ______________________________________________________________________ |