summaryrefslogtreecommitdiffstats
path: root/Documentation/input
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/input')
-rw-r--r--Documentation/input/alps.txt4
-rw-r--r--Documentation/input/event-codes.txt2
-rw-r--r--Documentation/input/gpio-tilt.txt2
-rw-r--r--Documentation/input/iforce-protocol.txt2
-rw-r--r--Documentation/input/walkera0701.txt2
-rw-r--r--Documentation/input/yealink.txt2
6 files changed, 7 insertions, 7 deletions
diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt
index 92ae734c00c3..b9d229fee6b9 100644
--- a/Documentation/input/alps.txt
+++ b/Documentation/input/alps.txt
@@ -58,7 +58,7 @@ To exit command mode, PSMOUSE_CMD_SETSTREAM (EA) is sent to the touchpad.
While in command mode, register addresses can be set by first sending a
specific command, either EC for v3 devices or F5 for v4 devices. Then the
address is sent one nibble at a time, where each nibble is encoded as a
-command with optional data. This enoding differs slightly between the v3 and
+command with optional data. This encoding differs slightly between the v3 and
v4 protocols.
Once an address has been set, the addressed register can be read by sending
@@ -139,7 +139,7 @@ ALPS Absolute Mode - Protocol Version 3
---------------------------------------
ALPS protocol version 3 has three different packet formats. The first two are
-associated with touchpad events, and the third is associatd with trackstick
+associated with touchpad events, and the third is associated with trackstick
events.
The first type is the touchpad position packet.
diff --git a/Documentation/input/event-codes.txt b/Documentation/input/event-codes.txt
index 96705616f582..3f0f5ce3338b 100644
--- a/Documentation/input/event-codes.txt
+++ b/Documentation/input/event-codes.txt
@@ -229,7 +229,7 @@ such device to feedback.
EV_PWR:
----------
EV_PWR events are a special type of event used specifically for power
-mangement. Its usage is not well defined. To be addressed later.
+management. Its usage is not well defined. To be addressed later.
Device properties:
=================
diff --git a/Documentation/input/gpio-tilt.txt b/Documentation/input/gpio-tilt.txt
index 06d60c3ff5e7..2cdfd9bcb1af 100644
--- a/Documentation/input/gpio-tilt.txt
+++ b/Documentation/input/gpio-tilt.txt
@@ -28,7 +28,7 @@ Example:
--------
Example configuration for a single TS1003 tilt switch that rotates around
-one axis in 4 steps and emitts the current tilt via two GPIOs.
+one axis in 4 steps and emits the current tilt via two GPIOs.
static int sg060_tilt_enable(struct device *dev) {
/* code to enable the sensors */
diff --git a/Documentation/input/iforce-protocol.txt b/Documentation/input/iforce-protocol.txt
index 2d5fbfd6023e..66287151c54a 100644
--- a/Documentation/input/iforce-protocol.txt
+++ b/Documentation/input/iforce-protocol.txt
@@ -97,7 +97,7 @@ LEN= 0e
*** Attack and fade ***
OP= 02
LEN= 08
-00-01 Address where to store the parameteres
+00-01 Address where to store the parameters
02-03 Duration of attack (little endian encoding, in ms)
04 Level at end of attack. Signed byte.
05-06 Duration of fade.
diff --git a/Documentation/input/walkera0701.txt b/Documentation/input/walkera0701.txt
index 561385d38482..49e3ac60dcef 100644
--- a/Documentation/input/walkera0701.txt
+++ b/Documentation/input/walkera0701.txt
@@ -91,7 +91,7 @@ absolute binary value. (10 bits per channel). Next nibble is checksum for
first ten nibbles.
Next nibbles 12 .. 21 represents four channels (not all channels can be
-directly controlled from TX). Binary representations ar the same as in first
+directly controlled from TX). Binary representations are the same as in first
four channels. In nibbles 22 and 23 is a special magic number. Nibble 24 is
checksum for nibbles 12..23.
diff --git a/Documentation/input/yealink.txt b/Documentation/input/yealink.txt
index 5360e434486c..8277b76ec506 100644
--- a/Documentation/input/yealink.txt
+++ b/Documentation/input/yealink.txt
@@ -93,7 +93,7 @@ Format description:
Format specifier
'8' : Generic 7 segment digit with individual addressable segments
- Reduced capability 7 segm digit, when segments are hard wired together.
+ Reduced capability 7 segment digit, when segments are hard wired together.
'1' : 2 segments digit only able to produce a 1.
'e' : Most significant day of the month digit,
able to produce at least 1 2 3.