diff options
Diffstat (limited to 'Documentation/hwmon')
| -rw-r--r-- | Documentation/hwmon/amc6821 | 102 | ||||
| -rw-r--r-- | Documentation/hwmon/k10temp | 65 | ||||
| -rw-r--r-- | Documentation/hwmon/lis3lv02d | 55 | ||||
| -rw-r--r-- | Documentation/hwmon/w83627ehf | 10 |
4 files changed, 213 insertions, 19 deletions
diff --git a/Documentation/hwmon/amc6821 b/Documentation/hwmon/amc6821 new file mode 100644 index 000000000000..ced8359c50f8 --- /dev/null +++ b/Documentation/hwmon/amc6821 @@ -0,0 +1,102 @@ +Kernel driver amc6821 +===================== + +Supported chips: + Texas Instruments AMC6821 + Prefix: 'amc6821' + Addresses scanned: 0x18, 0x19, 0x1a, 0x2c, 0x2d, 0x2e, 0x4c, 0x4d, 0x4e + Datasheet: http://focus.ti.com/docs/prod/folders/print/amc6821.html + +Authors: + Tomaz Mertelj <tomaz.mertelj@guest.arnes.si> + + +Description +----------- + +This driver implements support for the Texas Instruments amc6821 chip. +The chip has one on-chip and one remote temperature sensor and one pwm fan +regulator. +The pwm can be controlled either from software or automatically. + +The driver provides the following sensor accesses in sysfs: + +temp1_input ro on-chip temperature +temp1_min rw " +temp1_max rw " +temp1_crit rw " +temp1_min_alarm ro " +temp1_max_alarm ro " +temp1_crit_alarm ro " + +temp2_input ro remote temperature +temp2_min rw " +temp2_max rw " +temp2_crit rw " +temp2_min_alarm ro " +temp2_max_alarm ro " +temp2_crit_alarm ro " +temp2_fault ro " + +fan1_input ro tachometer speed +fan1_min rw " +fan1_max rw " +fan1_fault ro " +fan1_div rw Fan divisor can be either 2 or 4. + +pwm1 rw pwm1 +pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled + by remote temperature, 3=fan controlled by + combination of the on-chip temperature and + remote-sensor temperature, +pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3 +pwm1_auto_point1_pwm ro Hardwired to 0, shared for both + temperature channels. +pwm1_auto_point2_pwm rw This value is shared for both temperature + channels. +pwm1_auto_point3_pwm rw Hardwired to 255, shared for both + temperature channels. + +temp1_auto_point1_temp ro Hardwired to temp2_auto_point1_temp + which is rw. Below this temperature fan stops. +temp1_auto_point2_temp rw The low-temperature limit of the proportional + range. Below this temperature + pwm1 = pwm1_auto_point2_pwm. It can go from + 0 degree C to 124 degree C in steps of + 4 degree C. Read it out after writing to get + the actual value. +temp1_auto_point3_temp rw Above this temperature fan runs at maximum + speed. It can go from temp1_auto_point2_temp. + It can only have certain discrete values + which depend on temp1_auto_point2_temp and + pwm1_auto_point2_pwm. Read it out after + writing to get the actual value. + +temp2_auto_point1_temp rw Must be between 0 degree C and 63 degree C and + it defines the passive cooling temperature. + Below this temperature the fan stops in + the closed loop mode. +temp2_auto_point2_temp rw The low-temperature limit of the proportional + range. Below this temperature + pwm1 = pwm1_auto_point2_pwm. It can go from + 0 degree C to 124 degree C in steps + of 4 degree C. + +temp2_auto_point3_temp rw Above this temperature fan runs at maximum + speed. It can only have certain discrete + values which depend on temp2_auto_point2_temp + and pwm1_auto_point2_pwm. Read it out after + writing to get actual value. + + +Module parameters +----------------- + +If your board has a BIOS that initializes the amc6821 correctly, you should +load the module with: init=0. + +If your board BIOS doesn't initialize the chip, or you want +different settings, you can set the following parameters: +init=1, +pwminv: 0 default pwm output, 1 inverts pwm output. + diff --git a/Documentation/hwmon/k10temp b/Documentation/hwmon/k10temp new file mode 100644 index 000000000000..6526eee525a6 --- /dev/null +++ b/Documentation/hwmon/k10temp @@ -0,0 +1,65 @@ +Kernel driver k10temp +===================== + +Supported chips: +* AMD Family 10h processors: + Socket F: Quad-Core/Six-Core/Embedded Opteron (but see below) + Socket AM2+: Quad-Core Opteron, Phenom (II) X3/X4, Athlon X2 (but see below) + Socket AM3: Quad-Core Opteron, Athlon/Phenom II X2/X3/X4, Sempron II + Socket S1G3: Athlon II, Sempron, Turion II +* AMD Family 11h processors: + Socket S1G2: Athlon (X2), Sempron (X2), Turion X2 (Ultra) + + Prefix: 'k10temp' + Addresses scanned: PCI space + Datasheets: + BIOS and Kernel Developer's Guide (BKDG) For AMD Family 10h Processors: + http://support.amd.com/us/Processor_TechDocs/31116.pdf + BIOS and Kernel Developer's Guide (BKDG) for AMD Family 11h Processors: + http://support.amd.com/us/Processor_TechDocs/41256.pdf + Revision Guide for AMD Family 10h Processors: + http://support.amd.com/us/Processor_TechDocs/41322.pdf + Revision Guide for AMD Family 11h Processors: + http://support.amd.com/us/Processor_TechDocs/41788.pdf + AMD Family 11h Processor Power and Thermal Data Sheet for Notebooks: + http://support.amd.com/us/Processor_TechDocs/43373.pdf + AMD Family 10h Server and Workstation Processor Power and Thermal Data Sheet: + http://support.amd.com/us/Processor_TechDocs/43374.pdf + AMD Family 10h Desktop Processor Power and Thermal Data Sheet: + http://support.amd.com/us/Processor_TechDocs/43375.pdf + +Author: Clemens Ladisch <clemens@ladisch.de> + +Description +----------- + +This driver permits reading of the internal temperature sensor of AMD +Family 10h and 11h processors. + +All these processors have a sensor, but on those for Socket F or AM2+, +the sensor may return inconsistent values (erratum 319). The driver +will refuse to load on these revisions unless you specify the "force=1" +module parameter. + +Due to technical reasons, the driver can detect only the mainboard's +socket type, not the processor's actual capabilities. Therefore, if you +are using an AM3 processor on an AM2+ mainboard, you can safely use the +"force=1" parameter. + +There is one temperature measurement value, available as temp1_input in +sysfs. It is measured in degrees Celsius with a resolution of 1/8th degree. +Please note that it is defined as a relative value; to quote the AMD manual: + + Tctl is the processor temperature control value, used by the platform to + control cooling systems. Tctl is a non-physical temperature on an + arbitrary scale measured in degrees. It does _not_ represent an actual + physical temperature like die or case temperature. Instead, it specifies + the processor temperature relative to the point at which the system must + supply the maximum cooling for the processor's specified maximum case + temperature and maximum thermal power dissipation. + +The maximum value for Tctl is available in the file temp1_max. + +If the BIOS has enabled hardware temperature control, the threshold at +which the processor will throttle itself to avoid damage is available in +temp1_crit and temp1_crit_hyst. diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d index effe949a7282..06534f25e643 100644 --- a/Documentation/hwmon/lis3lv02d +++ b/Documentation/hwmon/lis3lv02d @@ -3,7 +3,8 @@ Kernel driver lis3lv02d Supported chips: - * STMicroelectronics LIS3LV02DL and LIS3LV02DQ + * STMicroelectronics LIS3LV02DL, LIS3LV02DQ (12 bits precision) + * STMicroelectronics LIS302DL, LIS3L02DQ, LIS331DL (8 bits) Authors: Yan Burman <burman.yan@gmail.com> @@ -13,32 +14,52 @@ Authors: Description ----------- -This driver provides support for the accelerometer found in various HP -laptops sporting the feature officially called "HP Mobile Data -Protection System 3D" or "HP 3D DriveGuard". It detects automatically -laptops with this sensor. Known models (for now the HP 2133, nc6420, -nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis -automatically oriented on standard way (eg: you can directly play -neverball). The accelerometer data is readable via -/sys/devices/platform/lis3lv02d. +This driver provides support for the accelerometer found in various HP laptops +sporting the feature officially called "HP Mobile Data Protection System 3D" or +"HP 3D DriveGuard". It detects automatically laptops with this sensor. Known +models (full list can be found in drivers/hwmon/hp_accel.c) will have their +axis automatically oriented on standard way (eg: you can directly play +neverball). The accelerometer data is readable via +/sys/devices/platform/lis3lv02d. Reported values are scaled +to mg values (1/1000th of earth gravity). Sysfs attributes under /sys/devices/platform/lis3lv02d/: position - 3D position that the accelerometer reports. Format: "(x,y,z)" -calibrate - read: values (x, y, z) that are used as the base for input - class device operation. - write: forces the base to be recalibrated with the current - position. -rate - reports the sampling rate of the accelerometer device in HZ +rate - read reports the sampling rate of the accelerometer device in HZ. + write changes sampling rate of the accelerometer device. + Only values which are supported by HW are accepted. +selftest - performs selftest for the chip as specified by chip manufacturer. This driver also provides an absolute input class device, allowing -the laptop to act as a pinball machine-esque joystick. +the laptop to act as a pinball machine-esque joystick. Joystick device can be +calibrated. Joystick device can be in two different modes. +By default output values are scaled between -32768 .. 32767. In joystick raw +mode, joystick and sysfs position entry have the same scale. There can be +small difference due to input system fuzziness feature. +Events are also available as input event device. + +Selftest is meant only for hardware diagnostic purposes. It is not meant to be +used during normal operations. Position data is not corrupted during selftest +but interrupt behaviour is not guaranteed to work reliably. In test mode, the +sensing element is internally moved little bit. Selftest measures difference +between normal mode and test mode. Chip specifications tell the acceptance +limit for each type of the chip. Limits are provided via platform data +to allow adjustment of the limits without a change to the actual driver. +Seltest returns either "OK x y z" or "FAIL x y z" where x, y and z are +measured difference between modes. Axes are not remapped in selftest mode. +Measurement values are provided to help HW diagnostic applications to make +final decision. + +On HP laptops, if the led infrastructure is activated, support for a led +indicating disk protection will be provided as /sys/class/leds/hp::hddprotect. Another feature of the driver is misc device called "freefall" that acts similar to /dev/rtc and reacts on free-fall interrupts received from the device. It supports blocking operations, poll/select and fasync operation modes. You must read 1 bytes from the device. The result is number of free-fall interrupts since the last successful -read (or 255 if number of interrupts would not fit). +read (or 255 if number of interrupts would not fit). See the hpfall.c +file for an example on using the device. Axes orientation @@ -55,7 +76,7 @@ the accelerometer are converted into a "standard" organisation of the axes * If the laptop is put upside-down, Z becomes negative If your laptop model is not recognized (cf "dmesg"), you can send an -email to the authors to add it to the database. When reporting a new +email to the maintainer to add it to the database. When reporting a new laptop, please include the output of "dmidecode" plus the value of /sys/devices/platform/lis3lv02d/position in these four cases. diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf index 02b74899edaf..b7e42ec4b26b 100644 --- a/Documentation/hwmon/w83627ehf +++ b/Documentation/hwmon/w83627ehf @@ -81,8 +81,14 @@ pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range: 0 (stop) to 255 (full) pwm[1-4]_enable - this file controls mode of fan/temperature control: - * 1 Manual Mode, write to pwm file any value 0-255 (full speed) - * 2 Thermal Cruise + * 1 Manual mode, write to pwm file any value 0-255 (full speed) + * 2 "Thermal Cruise" mode + * 3 "Fan Speed Cruise" mode + * 4 "Smart Fan III" mode + +pwm[1-4]_mode - controls if output is PWM or DC level + * 0 DC output (0 - 12v) + * 1 PWM output Thermal Cruise mode ------------------- |