diff options
Diffstat (limited to 'Documentation/hwmon/abituguru3')
| -rw-r--r-- | Documentation/hwmon/abituguru3 | 36 |
1 files changed, 23 insertions, 13 deletions
diff --git a/Documentation/hwmon/abituguru3 b/Documentation/hwmon/abituguru3 index a6ccfe4bb6aa..514f11f41e8b 100644 --- a/Documentation/hwmon/abituguru3 +++ b/Documentation/hwmon/abituguru3 @@ -3,41 +3,51 @@ Kernel driver abituguru3 Supported chips: * Abit uGuru revision 3 (Hardware Monitor part, reading only) + Prefix: 'abituguru3' + Addresses scanned: ISA 0x0E0 + Datasheet: Not available, this driver is based on reverse engineering. + Note: The uGuru is a microcontroller with onboard firmware which programs it to behave as a hwmon IC. There are many different revisions of the firmware and thus effectivly many different revisions of the uGuru. Below is an incomplete list with which revisions are used for which Motherboards: - uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) - uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO) - uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8) - uGuru 2.3.0.0 ~ 2.3.0.9 (AN8) - uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X, - AW9D-MAX) + + - uGuru 1.00 ~ 1.24 (AI7, KV8-MAX3, AN7) + - uGuru 2.0.0.0 ~ 2.0.4.2 (KV8-PRO) + - uGuru 2.1.0.0 ~ 2.1.2.8 (AS8, AV8, AA8, AG8, AA8XE, AX8) + - uGuru 2.3.0.0 ~ 2.3.0.9 (AN8) + - uGuru 3.0.0.0 ~ 3.0.x.x (AW8, AL8, AT8, NI8 SLI, AT8 32X, AN8 32X, + AW9D-MAX) + The abituguru3 driver is only for revison 3.0.x.x motherboards, this driver will not work on older motherboards. For older motherboards use the abituguru (without the 3 !) driver. Authors: - Hans de Goede <j.w.r.degoede@hhs.nl>, - (Initial reverse engineering done by Louis Kruger) + - Hans de Goede <j.w.r.degoede@hhs.nl>, + - (Initial reverse engineering done by Louis Kruger) Module Parameters ----------------- -* force: bool Force detection. Note this parameter only causes the +* force: bool + Force detection. Note this parameter only causes the detection to be skipped, and thus the insmod to succeed. If the uGuru can't be read the actual hwmon driver will not load and thus no hwmon device will get registered. -* verbose: bool Should the driver be verbose? - 0/off/false normal output - 1/on/true + verbose error reporting (default) +* verbose: bool + Should the driver be verbose? + + * 0/off/false normal output + * 1/on/true + verbose error reporting (default) + Default: 1 (the driver is still in the testing phase) Description @@ -62,4 +72,4 @@ neither is writing any of the sensor settings and writing / reading the fanspeed control registers (FanEQ) If you encounter any problems please mail me <j.w.r.degoede@hhs.nl> and -include the output of: "dmesg | grep abituguru" +include the output of: `dmesg | grep abituguru` |