summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt22
-rw-r--r--Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt27
-rw-r--r--Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.yaml49
-rw-r--r--Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt66
-rw-r--r--Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml76
-rw-r--r--Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml27
-rw-r--r--Documentation/devicetree/bindings/pci/cdns-pcie.yaml31
-rw-r--r--Documentation/devicetree/bindings/pci/layerscape-pcie-gen4.txt52
-rw-r--r--Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt125
-rw-r--r--Documentation/devicetree/bindings/pci/pci-ep.yaml41
-rw-r--r--Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml35
-rw-r--r--Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml52
12 files changed, 471 insertions, 132 deletions
diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
index 84fdc422792e..b6acbe694ffb 100644
--- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -18,7 +18,6 @@ Required properties:
- reg-names: Must be
- "elbi" External local bus interface registers
- "cfg" Meson specific registers
- - "phy" Meson PCIE PHY registers for AXG SoC Family
- "config" PCIe configuration space
- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
- clocks: Must contain an entry for each entry in clock-names.
@@ -26,13 +25,13 @@ Required properties:
- "pclk" PCIe GEN 100M PLL clock
- "port" PCIe_x(A or B) RC clock gate
- "general" PCIe Phy clock
- - "mipi" PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
- resets: phandle to the reset lines.
-- reset-names: must contain "phy" "port" and "apb"
- - "phy" Share PHY reset for AXG SoC Family
+- reset-names: must contain "port" and "apb"
- "port" Port A or B reset
- "apb" Share APB reset
-- phys: should contain a phandle to the shared phy for G12A SoC Family
+- phys: should contain a phandle to the PCIE phy
+- phy-names: must contain "pcie"
+
- device_type:
should be "pci". As specified in designware-pcie.txt
@@ -43,9 +42,8 @@ Example configuration:
compatible = "amlogic,axg-pcie", "snps,dw-pcie";
reg = <0x0 0xf9800000 0x0 0x400000
0x0 0xff646000 0x0 0x2000
- 0x0 0xff644000 0x0 0x2000
0x0 0xf9f00000 0x0 0x100000>;
- reg-names = "elbi", "cfg", "phy", "config";
+ reg-names = "elbi", "cfg", "config";
reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
#interrupt-cells = <1>;
@@ -58,17 +56,15 @@ Example configuration:
ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
clocks = <&clkc CLKID_USB
- &clkc CLKID_MIPI_ENABLE
&clkc CLKID_PCIE_A
&clkc CLKID_PCIE_CML_EN0>;
clock-names = "general",
- "mipi",
"pclk",
"port";
- resets = <&reset RESET_PCIE_PHY>,
- <&reset RESET_PCIE_A>,
+ resets = <&reset RESET_PCIE_A>,
<&reset RESET_PCIE_APB>;
- reset-names = "phy",
- "port",
+ reset-names = "port",
"apb";
+ phys = <&pcie_phy>;
+ phy-names = "pcie";
};
diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt
deleted file mode 100644
index 4a0475e2ba7e..000000000000
--- a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt
+++ /dev/null
@@ -1,27 +0,0 @@
-* Cadence PCIe endpoint controller
-
-Required properties:
-- compatible: Should contain "cdns,cdns-pcie-ep" to identify the IP used.
-- reg: Should contain the controller register base address and AXI interface
- region base address respectively.
-- reg-names: Must be "reg" and "mem" respectively.
-- cdns,max-outbound-regions: Set to maximum number of outbound regions
-
-Optional properties:
-- max-functions: Maximum number of functions that can be configured (default 1).
-- phys: From PHY bindings: List of Generic PHY phandles. One per lane if more
- than one in the list. If only one PHY listed it must manage all lanes.
-- phy-names: List of names to identify the PHY.
-
-Example:
-
-pcie@fc000000 {
- compatible = "cdns,cdns-pcie-ep";
- reg = <0x0 0xfc000000 0x0 0x01000000>,
- <0x0 0x80000000 0x0 0x40000000>;
- reg-names = "reg", "mem";
- cdns,max-outbound-regions = <16>;
- max-functions = /bits/ 8 <8>;
- phys = <&ep_phy0 &ep_phy1>;
- phy-names = "pcie-lane0","pcie-lane1";
-};
diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.yaml b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.yaml
new file mode 100644
index 000000000000..2996f8d4777c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.yaml
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/cdns,cdns-pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence PCIe EP Controller
+
+maintainers:
+ - Tom Joseph <tjoseph@cadence.com>
+
+allOf:
+ - $ref: "cdns-pcie.yaml#"
+ - $ref: "pci-ep.yaml#"
+
+properties:
+ compatible:
+ const: cdns,cdns-pcie-ep
+
+ reg:
+ maxItems: 2
+
+ reg-names:
+ items:
+ - const: reg
+ - const: mem
+
+required:
+ - reg
+ - reg-names
+
+examples:
+ - |
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pcie-ep@fc000000 {
+ compatible = "cdns,cdns-pcie-ep";
+ reg = <0x0 0xfc000000 0x0 0x01000000>,
+ <0x0 0x80000000 0x0 0x40000000>;
+ reg-names = "reg", "mem";
+ cdns,max-outbound-regions = <16>;
+ max-functions = /bits/ 8 <8>;
+ phys = <&pcie_phy0>;
+ phy-names = "pcie-phy";
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt
deleted file mode 100644
index 91de69c713a9..000000000000
--- a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt
+++ /dev/null
@@ -1,66 +0,0 @@
-* Cadence PCIe host controller
-
-This PCIe controller inherits the base properties defined in
-host-generic-pci.txt.
-
-Required properties:
-- compatible: Should contain "cdns,cdns-pcie-host" to identify the IP used.
-- reg: Should contain the controller register base address, PCIe configuration
- window base address, and AXI interface region base address respectively.
-- reg-names: Must be "reg", "cfg" and "mem" respectively.
-- #address-cells: Set to <3>
-- #size-cells: Set to <2>
-- device_type: Set to "pci"
-- ranges: Ranges for the PCI memory and I/O regions
-- #interrupt-cells: Set to <1>
-- interrupt-map-mask and interrupt-map: Standard PCI properties to define the
- mapping of the PCIe interface to interrupt numbers.
-
-Optional properties:
-- cdns,max-outbound-regions: Set to maximum number of outbound regions
- (default 32)
-- cdns,no-bar-match-nbits: Set into the no BAR match register to configure the
- number of least significant bits kept during inbound (PCIe -> AXI) address
- translations (default 32)
-- vendor-id: The PCI vendor ID (16 bits, default is design dependent)
-- device-id: The PCI device ID (16 bits, default is design dependent)
-- phys: From PHY bindings: List of Generic PHY phandles. One per lane if more
- than one in the list. If only one PHY listed it must manage all lanes.
-- phy-names: List of names to identify the PHY.
-
-Example:
-
-pcie@fb000000 {
- compatible = "cdns,cdns-pcie-host";
- device_type = "pci";
- #address-cells = <3>;
- #size-cells = <2>;
- bus-range = <0x0 0xff>;
- linux,pci-domain = <0>;
- cdns,max-outbound-regions = <16>;
- cdns,no-bar-match-nbits = <32>;
- vendor-id = /bits/ 16 <0x17cd>;
- device-id = /bits/ 16 <0x0200>;
-
- reg = <0x0 0xfb000000 0x0 0x01000000>,
- <0x0 0x41000000 0x0 0x00001000>,
- <0x0 0x40000000 0x0 0x04000000>;
- reg-names = "reg", "cfg", "mem";
-
- ranges = <0x02000000 0x0 0x42000000 0x0 0x42000000 0x0 0x1000000>,
- <0x01000000 0x0 0x43000000 0x0 0x43000000 0x0 0x0010000>;
-
- #interrupt-cells = <0x1>;
-
- interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 14 0x1
- 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 15 0x1
- 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 16 0x1
- 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 17 0x1>;
-
- interrupt-map-mask = <0x0 0x0 0x0 0x7>;
-
- msi-parent = <&its_pci>;
-
- phys = <&pcie_phy0>;
- phy-names = "pcie-phy";
-};
diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml
new file mode 100644
index 000000000000..cabbe46ff578
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.yaml
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/cdns,cdns-pcie-host.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence PCIe host controller
+
+maintainers:
+ - Tom Joseph <tjoseph@cadence.com>
+
+allOf:
+ - $ref: /schemas/pci/pci-bus.yaml#
+ - $ref: "cdns-pcie-host.yaml#"
+
+properties:
+ compatible:
+ const: cdns,cdns-pcie-host
+
+ reg:
+ maxItems: 3
+
+ reg-names:
+ items:
+ - const: reg
+ - const: cfg
+ - const: mem
+
+ msi-parent: true
+
+required:
+ - reg
+ - reg-names
+
+examples:
+ - |
+ bus {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pcie@fb000000 {
+ compatible = "cdns,cdns-pcie-host";
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ bus-range = <0x0 0xff>;
+ linux,pci-domain = <0>;
+ cdns,max-outbound-regions = <16>;
+ cdns,no-bar-match-nbits = <32>;
+ vendor-id = <0x17cd>;
+ device-id = <0x0200>;
+
+ reg = <0x0 0xfb000000 0x0 0x01000000>,
+ <0x0 0x41000000 0x0 0x00001000>,
+ <0x0 0x40000000 0x0 0x04000000>;
+ reg-names = "reg", "cfg", "mem";
+
+ ranges = <0x02000000 0x0 0x42000000 0x0 0x42000000 0x0 0x1000000>,
+ <0x01000000 0x0 0x43000000 0x0 0x43000000 0x0 0x0010000>;
+
+ #interrupt-cells = <0x1>;
+
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 14 0x1>,
+ <0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 15 0x1>,
+ <0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 16 0x1>,
+ <0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 17 0x1>;
+
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+
+ msi-parent = <&its_pci>;
+
+ phys = <&pcie_phy0>;
+ phy-names = "pcie-phy";
+ };
+ };
+...
diff --git a/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml b/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml
new file mode 100644
index 000000000000..ab6e43b636ec
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/cdns-pcie-host.yaml
@@ -0,0 +1,27 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/pci/cdns-pcie-host.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Cadence PCIe Host
+
+maintainers:
+ - Tom Joseph <tjoseph@cadence.com>
+
+allOf:
+ - $ref: "/schemas/pci/pci-bus.yaml#"
+ - $ref: "cdns-pcie.yaml#"
+
+properties:
+ cdns,no-bar-match-nbits:
+ description:
+ Set into the no BAR match register to configure the number of least
+ significant bits kept during inbound (PCIe -> AXI) address translations
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 64
+ default: 32
+
+ msi-parent: true
diff --git a/Documentation/devicetree/bindings/pci/cdns-pcie.yaml b/Documentation/devicetree/bindings/pci/cdns-pcie.yaml
new file mode 100644
index 000000000000..6887ccc339cc
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/cdns-pcie.yaml
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/pci/cdns-pcie.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Cadence PCIe Core
+
+maintainers:
+ - Tom Joseph <tjoseph@cadence.com>
+
+properties:
+ cdns,max-outbound-regions:
+ description: maximum number of outbound regions
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ maximum: 32
+ default: 32
+
+ phys:
+ description:
+ One per lane if more than one in the list. If only one PHY listed it must
+ manage all lanes.
+ minItems: 1
+ maxItems: 16
+
+ phy-names:
+ items:
+ - const: pcie-phy
+ # FIXME: names when more than 1
diff --git a/Documentation/devicetree/bindings/pci/layerscape-pcie-gen4.txt b/Documentation/devicetree/bindings/pci/layerscape-pcie-gen4.txt
new file mode 100644
index 000000000000..b40fb5d15d3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/layerscape-pcie-gen4.txt
@@ -0,0 +1,52 @@
+NXP Layerscape PCIe Gen4 controller
+
+This PCIe controller is based on the Mobiveil PCIe IP and thus inherits all
+the common properties defined in mobiveil-pcie.txt.
+
+Required properties:
+- compatible: should contain the platform identifier such as:
+ "fsl,lx2160a-pcie"
+- reg: base addresses and lengths of the PCIe controller register blocks.
+ "csr_axi_slave": Bridge config registers
+ "config_axi_slave": PCIe controller registers
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+ entry for each entry in the interrupt-names property.
+- interrupt-names: It could include the following entries:
+ "intr": The interrupt that is asserted for controller interrupts
+ "aer": Asserted for aer interrupt when chip support the aer interrupt with
+ none MSI/MSI-X/INTx mode,but there is interrupt line for aer.
+ "pme": Asserted for pme interrupt when chip support the pme interrupt with
+ none MSI/MSI-X/INTx mode,but there is interrupt line for pme.
+- dma-coherent: Indicates that the hardware IP block can ensure the coherency
+ of the data transferred from/to the IP block. This can avoid the software
+ cache flush/invalid actions, and improve the performance significantly.
+- msi-parent : See the generic MSI binding described in
+ Documentation/devicetree/bindings/interrupt-controller/msi.txt.
+
+Example:
+
+ pcie@3400000 {
+ compatible = "fsl,lx2160a-pcie";
+ reg = <0x00 0x03400000 0x0 0x00100000 /* controller registers */
+ 0x80 0x00000000 0x0 0x00001000>; /* configuration space */
+ reg-names = "csr_axi_slave", "config_axi_slave";
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* AER interrupt */
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME interrupt */
+ <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+ interrupt-names = "aer", "pme", "intr";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ apio-wins = <8>;
+ ppio-wins = <8>;
+ dma-coherent;
+ bus-range = <0x0 0xff>;
+ msi-parent = <&its>;
+ ranges = <0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 2 &gic 0 0 GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 3 &gic 0 0 GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+ <0000 0 0 4 &gic 0 0 GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+ };
diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
index b739f92da58e..faa3ef5adfbb 100644
--- a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt
@@ -1,11 +1,11 @@
NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based)
-This PCIe host controller is based on the Synopsis Designware PCIe IP
+This PCIe controller is based on the Synopsis Designware PCIe IP
and thus inherits all the common properties defined in designware-pcie.txt.
+Some of the controller instances are dual mode where in they can work either
+in root port mode or endpoint mode but one at a time.
Required properties:
-- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie".
-- device_type: Must be "pci"
- power-domains: A phandle to the node that controls power to the respective
PCIe controller and a specifier name for the PCIe controller. Following are
the specifiers for the different PCIe controllers
@@ -32,6 +32,32 @@ Required properties:
entry for each entry in the interrupt-names property.
- interrupt-names: Must include the following entries:
"intr": The Tegra interrupt that is asserted for controller interrupts
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - core
+- resets: Must contain an entry for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+ - apb
+ - core
+- phys: Must contain a phandle to P2U PHY for each entry in phy-names.
+- phy-names: Must include an entry for each active lane.
+ "p2u-N": where N ranges from 0 to one less than the total number of lanes
+- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed
+ by controller-id. Following are the controller ids for each controller.
+ 0: C0
+ 1: C1
+ 2: C2
+ 3: C3
+ 4: C4
+ 5: C5
+- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals
+
+RC mode:
+- compatible: Tegra19x must contain "nvidia,tegra194-pcie"
+- device_type: Must be "pci" for RC mode
+- interrupt-names: Must include the following entries:
"msi": The Tegra interrupt that is asserted when an MSI is received
- bus-range: Range of bus numbers associated with this controller
- #address-cells: Address representation for root ports (must be 3)
@@ -60,27 +86,15 @@ Required properties:
- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
Please refer to the standard PCI bus binding document for a more detailed
explanation.
-- clocks: Must contain an entry for each entry in clock-names.
- See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
- - core
-- resets: Must contain an entry for each entry in reset-names.
- See ../reset/reset.txt for details.
-- reset-names: Must include the following entries:
- - apb
- - core
-- phys: Must contain a phandle to P2U PHY for each entry in phy-names.
-- phy-names: Must include an entry for each active lane.
- "p2u-N": where N ranges from 0 to one less than the total number of lanes
-- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed
- by controller-id. Following are the controller ids for each controller.
- 0: C0
- 1: C1
- 2: C2
- 3: C3
- 4: C4
- 5: C5
-- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals
+
+EP mode:
+In Tegra194, Only controllers C0, C4 & C5 support EP mode.
+- compatible: Tegra19x must contain "nvidia,tegra194-pcie-ep"
+- reg-names: Must include the following entries:
+ "addr_space": Used to map remote RC address space
+- reset-gpios: Must contain a phandle to a GPIO controller followed by
+ GPIO that is being used as PERST input signal. Please refer to pci.txt
+ document.
Optional properties:
- pinctrl-names: A list of pinctrl state names.
@@ -104,6 +118,8 @@ Optional properties:
specified in microseconds
- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be
specified in microseconds
+
+RC mode:
- vpcie3v3-supply: A phandle to the regulator node that supplies 3.3V to the slot
if the platform has one such slot. (Ex:- x16 slot owned by C5 controller
in p2972-0000 platform).
@@ -111,11 +127,18 @@ Optional properties:
if the platform has one such slot. (Ex:- x16 slot owned by C5 controller
in p2972-0000 platform).
+EP mode:
+- nvidia,refclk-select-gpios: Must contain a phandle to a GPIO controller
+ followed by GPIO that is being used to enable REFCLK to controller from host
+
+NOTE:- On Tegra194's P2972-0000 platform, only C5 controller can be enabled to
+operate in the endpoint mode because of the way the platform is designed.
+
Examples:
=========
-Tegra194:
---------
+Tegra194 RC mode:
+-----------------
pcie@14180000 {
compatible = "nvidia,tegra194-pcie", "snps,dw-pcie";
@@ -169,3 +192,53 @@ Tegra194:
<&p2u_hsio_5>;
phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
};
+
+Tegra194 EP mode:
+-----------------
+
+ pcie_ep@141a0000 {
+ compatible = "nvidia,tegra194-pcie-ep", "snps,dw-pcie-ep";
+ power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8A>;
+ reg = <0x00 0x141a0000 0x0 0x00020000 /* appl registers (128K) */
+ 0x00 0x3a040000 0x0 0x00040000 /* iATU_DMA reg space (256K) */
+ 0x00 0x3a080000 0x0 0x00040000 /* DBI reg space (256K) */
+ 0x1c 0x00000000 0x4 0x00000000>; /* Address Space (16G) */
+ reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+ num-lanes = <8>;
+ num-ib-windows = <2>;
+ num-ob-windows = <8>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&clkreq_c5_bi_dir_state>;
+
+ clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>;
+ clock-names = "core";
+
+ resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>,
+ <&bpmp TEGRA194_RESET_PEX1_CORE_5>;
+ reset-names = "apb", "core";
+
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */
+ interrupt-names = "intr";
+
+ nvidia,bpmp = <&bpmp 5>;
+
+ nvidia,aspm-cmrt-us = <60>;
+ nvidia,aspm-pwr-on-t-us = <20>;
+ nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+ vddio-pex-ctl-supply = <&vdd_1v8ao>;
+
+ reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>;
+
+ nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5)
+ GPIO_ACTIVE_HIGH>;
+
+ phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+ <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+ <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+
+ phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+ "p2u-5", "p2u-6", "p2u-7";
+ };
diff --git a/Documentation/devicetree/bindings/pci/pci-ep.yaml b/Documentation/devicetree/bindings/pci/pci-ep.yaml
new file mode 100644
index 000000000000..b3df100705b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/pci-ep.yaml
@@ -0,0 +1,41 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/pci-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: PCI Endpoint Controller Schema
+
+description: |
+ Common properties for PCI Endpoint Controller Nodes.
+
+maintainers:
+ - Kishon Vijay Abraham I <kishon@ti.com>
+
+properties:
+ $nodename:
+ pattern: "^pcie-ep@"
+
+ max-functions:
+ description: Maximum number of functions that can be configured
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint8
+ minimum: 1
+ default: 1
+ maximum: 255
+
+ max-link-speed:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 1, 2, 3, 4 ]
+
+ num-lanes:
+ description: maximum number of lanes
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 1
+ default: 1
+ maximum: 16
+
+required:
+ - compatible
diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml
new file mode 100644
index 000000000000..88683db6cf81
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml
@@ -0,0 +1,35 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/amlogic,meson-axg-mipi-pcie-analog.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Amlogic AXG shared MIPI/PCIE analog PHY
+
+maintainers:
+ - Remi Pommarel <repk@triplefau.lt>
+
+properties:
+ compatible:
+ const: amlogic,axg-mipi-pcie-analog-phy
+
+ reg:
+ maxItems: 1
+
+ "#phy-cells":
+ const: 1
+
+required:
+ - compatible
+ - reg
+ - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ mpphy: phy@0 {
+ compatible = "amlogic,axg-mipi-pcie-analog-phy";
+ reg = <0x0 0x0 0x0 0xc>;
+ #phy-cells = <1>;
+ };
diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml
new file mode 100644
index 000000000000..086478aec946
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/amlogic,meson-axg-pcie.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Amlogic AXG PCIE PHY
+
+maintainers:
+ - Remi Pommarel <repk@triplefau.lt>
+
+properties:
+ compatible:
+ const: amlogic,axg-pcie-phy
+
+ reg:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ const: analog
+
+ "#phy-cells":
+ const: 0
+
+required:
+ - compatible
+ - reg
+ - phys
+ - phy-names
+ - resets
+ - "#phy-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/reset/amlogic,meson-axg-reset.h>
+ #include <dt-bindings/phy/phy.h>
+ pcie_phy: pcie-phy@ff644000 {
+ compatible = "amlogic,axg-pcie-phy";
+ reg = <0x0 0xff644000 0x0 0x1c>;
+ resets = <&reset RESET_PCIE_PHY>;
+ phys = <&mipi_analog_phy PHY_TYPE_PCIE>;
+ phy-names = "analog";
+ #phy-cells = <0>;
+ };