diff options
Diffstat (limited to 'Documentation/devicetree')
22 files changed, 423 insertions, 34 deletions
diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt index 8855bfcfd778..d90e17e2428b 100644 --- a/Documentation/devicetree/bindings/connector/usb-connector.txt +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt @@ -29,15 +29,15 @@ Required properties for usb-c-connector with power delivery support: in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 Source_Capabilities Message, the order of each entry(PDO) should follow the PD spec chapter 6.4.1. Required for power source and power dual role. - User can specify the source PDO array via PDO_FIXED/BATT/VAR() defined in - dt-bindings/usb/pd.h. + User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() + defined in dt-bindings/usb/pd.h. - sink-pdos: An array of u32 with each entry providing supported power sink data object(PDO), the detailed bit definitions of PDO can be found in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 Sink Capabilities Message, the order of each entry(PDO) should follow the PD spec chapter 6.4.1. Required for power sink and power dual role. - User can specify the sink PDO array via PDO_FIXED/BATT/VAR() defined in - dt-bindings/usb/pd.h. + User can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined + in dt-bindings/usb/pd.h. - op-sink-microwatt: Sink required operating power in microwatt, if source can't offer the power, Capability Mismatch is set. Required for power sink and power dual role. diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt index 0aced97d8092..b640845fec67 100644 --- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt +++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt @@ -8,6 +8,7 @@ Required properties: "brcm,iproc-nsp-sata-phy" "brcm,phy-sata3" "brcm,iproc-sr-sata-phy" + "brcm,bcm63138-sata-phy" - address-cells: should be 1 - size-cells: should be 0 - reg: register ranges for the PHY PCB interface diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt b/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt new file mode 100644 index 000000000000..7f49fd54ebc1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cadence-dp.txt @@ -0,0 +1,30 @@ +Cadence MHDP DisplayPort SD0801 PHY binding +=========================================== + +This binding describes the Cadence SD0801 PHY hardware included with +the Cadence MHDP DisplayPort controller. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be "cdns,dp-phy" +- reg : Defines the following sets of registers in the parent + mhdp device: + - Offset of the DPTX PHY configuration registers + - Offset of the SD0801 PHY configuration registers +- #phy-cells : from the generic PHY bindings, must be 0. + +Optional properties: +- num_lanes : Number of DisplayPort lanes to use (1, 2 or 4) +- max_bit_rate : Maximum DisplayPort link bit rate to use, in Mbps (2160, + 2430, 2700, 3240, 4320, 5400 or 8100) +------------------------------------------------------------------------------- + +Example: + dp_phy: phy@f0fb030a00 { + compatible = "cdns,dp-phy"; + reg = <0xf0 0xfb030a00 0x0 0x00000040>, + <0xf0 0xfb500000 0x0 0x00100000>; + num_lanes = <4>; + max_bit_rate = <8100>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt new file mode 100644 index 000000000000..710cccd5ee56 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt @@ -0,0 +1,43 @@ +ROCKCHIP HDMI PHY WITH INNO IP BLOCK + +Required properties: + - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-hdmi-phy", + * "rockchip,rk3328-hdmi-phy"; + - reg : Address and length of the hdmi phy control register set + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must contain "sysclk" for system + control and register configuration, "refoclk" for crystal- + oscillator reference PLL clock input and "refpclk" for pclk- + based refeference PLL clock input. + - #clock-cells: should be 0. + - clock-output-names : shall be the name for the output clock. + - interrupts : phandle + interrupt specified for the hdmiphy interrupt + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + +Optional properties for rk3328-hdmi-phy: + - nvmem-cells = phandle + nvmem specifier for the cpu-version efuse + - nvmem-cell-names : "cpu-version" to read the chip version, required + for adjustment to some frequency settings + +Example: + hdmi_phy: hdmi-phy@12030000 { + compatible = "rockchip,rk3228-hdmi-phy"; + reg = <0x12030000 0x10000>; + #phy-cells = <0>; + clocks = <&cru PCLK_HDMI_PHY>, <&xin24m>, <&cru DCLK_HDMIPHY>; + clock-names = "sysclk", "refoclk", "refpclk"; + #clock-cells = <0>; + clock-output-names = "hdmi_phy"; + status = "disabled"; + }; + +Then the PHY can be used in other nodes such as: + + hdmi: hdmi@200a0000 { + compatible = "rockchip,rk3228-dw-hdmi"; + ... + phys = <&hdmi_phy>; + phy-names = "hdmi"; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index 0c7629e88bf3..adf20b2bdf71 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -10,16 +10,20 @@ Required properties: "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, - "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845, + "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845. - - reg: - - For "qcom,sdm845-qmp-usb3-phy": - - index 0: address and length of register set for PHY's common serdes - block. - - named register "dp_com" (using reg-names): address and length of the - DP_COM control block. - - For all others: - - offset and length of register set for PHY's common serdes block. +- reg: + - index 0: address and length of register set for PHY's common + serdes block. + - index 1: address and length of the DP_COM control block (for + "qcom,sdm845-qmp-usb3-phy" only). + +- reg-names: + - For "qcom,sdm845-qmp-usb3-phy": + - Should be: "reg-base", "dp_com" + - For all others: + - The reg-names property shouldn't be defined. - #clock-cells: must be 1 - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe @@ -35,6 +39,7 @@ Required properties: "aux" for phy aux clock, "ref" for 19.2 MHz ref clk, "com_aux" for phy common block aux clock, + "ref_aux" for phy reference aux clock, For "qcom,msm8996-qmp-pcie-phy" must contain: "aux", "cfg_ahb", "ref". For "qcom,msm8996-qmp-usb3-phy" must contain: diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index fb4a204da2bf..de7b5393c163 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -1,10 +1,12 @@ * Renesas R-Car generation 3 USB 2.0 PHY This file provides information on what the device node for the R-Car generation -3 USB 2.0 PHY contains. +3 and RZ/G2 USB 2.0 PHY contain. Required properties: -- compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 +- compatible: "renesas,usb2-phy-r8a774a1" if the device is a part of an R8A774A1 + SoC. + "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. "renesas,usb2-phy-r8a7796" if the device is a part of an R8A7796 SoC. @@ -14,7 +16,8 @@ Required properties: R8A77990 SoC. "renesas,usb2-phy-r8a77995" if the device is a part of an R8A77995 SoC. - "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 compatible device. + "renesas,rcar-gen3-usb2-phy" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first @@ -31,6 +34,8 @@ channel as USB OTG: - interrupts: interrupt specifier for the PHY. - vbus-supply: Phandle to a regulator that provides power to the VBUS. This regulator will be managed during the PHY power on/off sequence. +- renesas,no-otg-pins: boolean, specify when a board does not provide proper + otg pins. Example (R-Car H3): diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt index 47dd296ecead..9d9826609c2f 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb3.txt @@ -1,20 +1,22 @@ * Renesas R-Car generation 3 USB 3.0 PHY This file provides information on what the device node for the R-Car generation -3 USB 3.0 PHY contains. +3 and RZ/G2 USB 3.0 PHY contain. If you want to enable spread spectrum clock (ssc), you should use USB_EXTAL instead of USB3_CLK. However, if you don't want to these features, you don't need this driver. Required properties: -- compatible: "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 +- compatible: "renesas,r8a774a1-usb3-phy" if the device is a part of an R8A774A1 + SoC. + "renesas,r8a7795-usb3-phy" if the device is a part of an R8A7795 SoC. "renesas,r8a7796-usb3-phy" if the device is a part of an R8A7796 SoC. "renesas,r8a77965-usb3-phy" if the device is a part of an R8A77965 SoC. - "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 compatible - device. + "renesas,rcar-gen3-usb3-phy" for a generic R-Car Gen3 or RZ/G2 + compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt new file mode 100644 index 000000000000..1889d3b89d68 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt @@ -0,0 +1,31 @@ +Socionext UniPhier PCIe PHY bindings + +This describes the devicetree bindings for PHY interface built into +PCIe controller implemented on Socionext UniPhier SoCs. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY + "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Must be zero. +- clocks: A phandle to the clock gate for PCIe glue layer including + this phy. +- resets: A phandle to the reset line for PCIe glue layer including + this phy. + +Optional properties: +- socionext,syscon: A phandle to system control to set configurations + for phy. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + pcie_phy: phy@66038000 { + compatible = "socionext,uniphier-ld20-pcie-phy"; + reg = <0x66038000 0x4000>; + #phy-cells = <0>; + clocks = <&sys_clk 24>; + resets = <&sys_rst 24>; + socionext,syscon = <&soc_glue>; + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt new file mode 100644 index 000000000000..b43b28250cc0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb2-phy.txt @@ -0,0 +1,45 @@ +Socionext UniPhier USB2 PHY + +This describes the devicetree bindings for PHY interface built into +USB2 controller implemented on Socionext UniPhier SoCs. + +Pro4 SoC has both USB2 and USB3 host controllers, however, this USB3 +controller doesn't include its own High-Speed PHY. This needs to specify +USB2 PHY instead of USB3 HS-PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb2-phy" - for Pro4 SoC + "socionext,uniphier-ld11-usb2-phy" - for LD11 SoC + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes required properties: +- #phy-cells: Should be 0. +- reg: The number of the PHY. + +Sub-nodes optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + soc-glue@5f800000 { + ... + usb-phy { + compatible = "socionext,uniphier-ld11-usb2-phy"; + usb_phy0: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + ... + }; + }; + + usb@5a800100 { + compatible = "socionext,uniphier-ehci", "generic-ehci"; + ... + phy-names = "usb"; + phys = <&usb_phy0>; + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt new file mode 100644 index 000000000000..e8d8086a7ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt @@ -0,0 +1,69 @@ +Socionext UniPhier USB3 High-Speed (HS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about High-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: Should contain the following: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. +- nvmem-cells: Phandles to nvmem cell that contains the trimming data. + Available only for HS-PHY implemented on LD20 and PXs3, and + if unspecified, default value is used. +- nvmem-cell-names: Should be the following names, which correspond to + each nvmem-cells. + All of the 3 parameters associated with the following names are + required for each port, if any one is omitted, the trimming data + of the port will not be set at all. + "rterm", "sel_t", "hs_i" - Each cell name for phy parameters + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_hsphy0: hs-phy@200 { + compatible = "socionext,uniphier-ld20-usb3-hsphy"; + reg = <0x200 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + nvmem-cell-names = "rterm", "sel_t", "hs_i"; + nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>, + <&usb_hs_i0>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt new file mode 100644 index 000000000000..490b815445e8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt @@ -0,0 +1,57 @@ +Socionext UniPhier USB3 Super-Speed (SS) PHY + +This describes the devicetree bindings for PHY interfaces built into +USB3 controller implemented on Socionext UniPhier SoCs. +Although the controller includes High-Speed PHY and Super-Speed PHY, +this describes about Super-Speed PHY. + +Required properties: +- compatible: Should contain one of the following: + "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC + "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC + "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC + "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC +- reg: Specifies offset and length of the register set for the device. +- #phy-cells: Should be 0. +- clocks: A list of phandles to the clock gate for USB3 glue layer. + According to the clock-names, appropriate clocks are required. +- clock-names: + "gio", "link" - for Pro4 SoC + "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional. + "phy", "link" - for others +- resets: A list of phandles to the reset control for USB3 glue layer. + According to the reset-names, appropriate resets are required. +- reset-names: + "gio", "link" - for Pro4 SoC + "phy", "link" - for others + +Optional properties: +- vbus-supply: A phandle to the regulator for USB VBUS. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + + usb-glue@65b00000 { + compatible = "socionext,uniphier-ld20-dwc3-glue", + "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x65b00000 0x400>; + + usb_vbus0: regulator { + ... + }; + + usb_ssphy0: ss-phy@300 { + compatible = "socionext,uniphier-ld20-usb3-ssphy"; + reg = <0x300 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 2e9318151df7..529e51879fb2 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -80,6 +80,8 @@ Optional properties: controller. It's expected that a mux state of 0 indicates device mode and a mux state of 1 indicates host mode. - mux-control-names: Shall be "usb_switch" if mux-controls is specified. +- pinctrl-names: Names for optional pin modes in "default", "host", "device" +- pinctrl-n: alternate pin modes i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 3e4c38b806ac..636630fb92d7 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -19,6 +19,7 @@ Exception for clocks: "cavium,octeon-7130-usb-uctl" "qcom,dwc3" "samsung,exynos5250-dwusb3" + "samsung,exynos5433-dwusb3" "samsung,exynos7-dwusb3" "sprd,sc9860-dwc3" "st,stih407-dwc3" diff --git a/Documentation/devicetree/bindings/usb/ehci-mv.txt b/Documentation/devicetree/bindings/usb/ehci-mv.txt new file mode 100644 index 000000000000..335589895763 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-mv.txt @@ -0,0 +1,23 @@ +* Marvell PXA/MMP EHCI controller. + +Required properties: + +- compatible: must be "marvell,pxau2o-ehci" +- reg: physical base addresses of the controller and length of memory mapped region +- interrupts: one EHCI controller interrupt should be described here +- clocks: phandle list of usb clocks +- clock-names: should be "USBCLK" +- phys: phandle for the PHY device +- phy-names: should be "usb" + +Example: + + ehci0: usb-ehci@d4208000 { + compatible = "marvell,pxau2o-ehci"; + reg = <0xd4208000 0x200>; + interrupts = <44>; + clocks = <&soc_clocks MMP2_CLK_USB>; + clock-names = "USBCLK"; + phys = <&usb_otg_phy>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt index c97374315049..b7111f43fa59 100644 --- a/Documentation/devicetree/bindings/usb/exynos-usb.txt +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -83,6 +83,8 @@ Required properties: - compatible: should be one of the following - "samsung,exynos5250-dwusb3": for USB 3.0 DWC3 controller on Exynos5250/5420. + "samsung,exynos5433-dwusb3": for USB 3.0 DWC3 controller on + Exynos5433. "samsung,exynos7-dwusb3": for USB 3.0 DWC3 controller on Exynos7. - #address-cells, #size-cells : should be '1' if the device has sub-nodes with 'reg' property. diff --git a/Documentation/devicetree/bindings/usb/faraday,fotg210.txt b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt new file mode 100644 index 000000000000..06a2286e2054 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/faraday,fotg210.txt @@ -0,0 +1,35 @@ +Faraday FOTG Host controller + +This OTG-capable USB host controller is found in Cortina Systems +Gemini and other SoC products. + +Required properties: +- compatible: should be one of: + "faraday,fotg210" + "cortina,gemini-usb", "faraday,fotg210" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Optional properties: +- clocks: should contain the IP block clock +- clock-names: should be "PCLK" for the IP block clock + +Required properties for "cortina,gemini-usb" compatible: +- syscon: a phandle to the system controller to access PHY registers + +Optional properties for "cortina,gemini-usb" compatible: +- cortina,gemini-mini-b: boolean property that indicates that a Mini-B + OTG connector is in use +- wakeup-source: see power/wakeup-source.txt + +Example for Gemini: + +usb@68000000 { + compatible = "cortina,gemini-usb", "faraday,fotg210"; + reg = <0x68000000 0x1000>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cc 12>; + clock-names = "PCLK"; + syscon = <&syscon>; + wakeup-source; +}; diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 6087dc7f209e..a5d011d2efc8 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -5,10 +5,19 @@ Required properties : - reg : I2C slave address - interrupts : Interrupt specifier -Optional properties : -- fcs,operating-sink-microwatt : - Minimum amount of power accepted from a sink - when negotiating +Required sub-node: +- connector : The "usb-c-connector" attached to the FUSB302 IC. The bindings + of the connector node are specified in: + + Documentation/devicetree/bindings/connector/usb-connector.txt + +Deprecated properties : +- fcs,max-sink-microvolt : Maximum sink voltage accepted by port controller +- fcs,max-sink-microamp : Maximum sink current accepted by port controller +- fcs,max-sink-microwatt : Maximum sink power accepted by port controller +- fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink + when negotiating + Example: @@ -17,7 +26,16 @@ fusb302: typec-portc@54 { reg = <0x54>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - fcs,max-sink-microvolt = <12000000>; - fcs,max-sink-microamp = <3000000>; - fcs,max-sink-microwatt = <36000000>; + + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_VAR(3000, 12000, 3000) + PDO_PPS_APDO(3000, 11000, 3000)>; + op-sink-microwatt = <10000000>; + }; }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt index 2c071bb5801e..d366555166d0 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usb3.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -2,11 +2,13 @@ Renesas Electronics USB3.0 Peripheral driver Required properties: - compatible: Must contain one of the following: + - "renesas,r8a774a1-usb3-peri" - "renesas,r8a7795-usb3-peri" - "renesas,r8a7796-usb3-peri" - "renesas,r8a77965-usb3-peri" - - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 compatible - device + - "renesas,r8a77990-usb3-peri" + - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 or RZ/G2 + compatible device When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index 43960faf5a88..90719f501852 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -4,7 +4,9 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device + - "renesas,usbhs-r8a7744" for r8a7744 (RZ/G1N) compatible device - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device + - "renesas,usbhs-r8a774a1" for r8a774a1 (RZ/G2M) compatible device - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device @@ -13,10 +15,11 @@ Required properties: - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device - "renesas,usbhs-r8a77965" for r8a77965 (R-Car M3-N) compatible device + - "renesas,usbhs-r8a77990" for r8a77990 (R-Car E3) compatible device - "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device - "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device - "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices - - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device + - "renesas,rcar-gen3-usbhs" for R-Car Gen3 or RZ/G2 compatible devices - "renesas,rza1-usbhs" for RZ/A1 compatible device When compatible with the generic version, nodes must list the @@ -25,7 +28,11 @@ Required properties: - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - - clocks: A list of phandle + clock specifier pairs + - clocks: A list of phandle + clock specifier pairs. + - In case of "renesas,rcar-gen3-usbhs", two clocks are required. + First clock should be peripheral and second one should be host. + - In case of except above, one clock is required. First clock + should be peripheral. Optional properties: - renesas,buswait: Integer to use BUSWAIT register diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index 0f1b75386207..406252d14c6b 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -15,7 +15,11 @@ Optional properties: - needs-reset-on-resume : boolean, set this to force EHCI reset after resume - has-transaction-translator : boolean, set this if EHCI have a Transaction Translator built into the root hub. - - clocks : a list of phandle + clock specifier pairs + - clocks : a list of phandle + clock specifier pairs. In case of Renesas + R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second one + should be peripheral. - phys : see usb-hcd.txt in the current directory - resets : phandle + reset specifier pair diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt index a8d2103d1f3d..aaaa5255c972 100644 --- a/Documentation/devicetree/bindings/usb/usb-ohci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -12,7 +12,11 @@ Optional properties: - no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA - remote-wakeup-connected: remote wakeup is wired on the platform - num-ports : u32, to override the detected port count -- clocks : a list of phandle + clock specifier pairs +- clocks : a list of phandle + clock specifier pairs. In case of Renesas + R-Car Gen3 SoCs: + - if a host only channel: first clock should be host. + - if a USB DRD channel: first clock should be host and second one + should be peripheral. - phys : see usb-hcd.txt in the current directory - resets : a list of phandle + reset specifier pairs diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index ac4cd0d6195a..fea8b1545751 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -8,6 +8,8 @@ Required properties: - "marvell,armada-375-xhci" for Armada 375 SoCs - "marvell,armada-380-xhci" for Armada 38x SoCs - "renesas,xhci-r8a7743" for r8a7743 SoC + - "renesas,xhci-r8a7744" for r8a7744 SoC + - "renesas,xhci-r8a774a1" for r8a774a1 SoC - "renesas,xhci-r8a7790" for r8a7790 SoC - "renesas,xhci-r8a7791" for r8a7791 SoC - "renesas,xhci-r8a7793" for r8a7793 SoC @@ -17,7 +19,8 @@ Required properties: - "renesas,xhci-r8a77990" for r8a77990 SoC - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 or RZ/G1 compatible device - - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 or RZ/G2 compatible + device - "xhci-platform" (deprecated) When compatible with the generic version, nodes must list the |