diff options
Diffstat (limited to 'Documentation/devicetree')
4 files changed, 18 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index 419ff6c0a47f..dad3b2ec66d4 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -14,6 +14,8 @@ Required properties: tegra132, or tegra210. - "nxp,lpc3220-uart" - "ralink,rt2880-uart" + - For MediaTek BTIF, must contain '"mediatek,<chip>-btif", + "mediatek,mtk-btif"' where <chip> is mt7622, mt7623. - "altr,16550-FIFO32" - "altr,16550-FIFO64" - "altr,16550-FIFO128" diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 8d27d1a603e7..4fc96946f81d 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -41,6 +41,8 @@ Required properties: - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. + - "renesas,scif-r8a77995" for R8A77995 (R-Car D3) SCIF compatible UART. + - "renesas,hscif-r8a77995" for R8A77995 (R-Car D3) HSCIF compatible UART. - "renesas,scifa-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFA compatible UART. - "renesas,scifb-sh73a0" for SH73A0 (SH-Mobile AG5) SCIFB compatible UART. - "renesas,rcar-gen1-scif" for R-Car Gen1 SCIF compatible UART, diff --git a/Documentation/devicetree/bindings/serial/rs485.txt b/Documentation/devicetree/bindings/serial/rs485.txt index 32b1fa1f2a5b..b8415936dfdb 100644 --- a/Documentation/devicetree/bindings/serial/rs485.txt +++ b/Documentation/devicetree/bindings/serial/rs485.txt @@ -5,14 +5,13 @@ the built-in half-duplex mode. The properties described hereafter shall be given to a half-duplex capable UART node. -Required properties: +Optional properties: - rs485-rts-delay: prop-encoded-array <a b> where: * a is the delay between rts signal and beginning of data sent in milliseconds. it corresponds to the delay before sending data. * b is the delay between end of data sent and rts signal in milliseconds it corresponds to the delay after sending data and actual release of the line. - -Optional properties: + If this property is not specified, <0 0> is assumed. - linux,rs485-enabled-at-boot-time: empty property telling to enable the rs485 feature at boot time. It can be disabled later with proper ioctl. - rs485-rx-during-tx: empty property that enables the receiving of data even diff --git a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt index 85ec5f2b1996..3657f9f9d17a 100644 --- a/Documentation/devicetree/bindings/serial/st,stm32-usart.txt +++ b/Documentation/devicetree/bindings/serial/st,stm32-usart.txt @@ -1,12 +1,19 @@ * STMicroelectronics STM32 USART Required properties: -- compatible: Can be either "st,stm32-usart", "st,stm32-uart", -"st,stm32f7-usart" or "st,stm32f7-uart" depending on whether -the device supports synchronous mode and is compatible with -stm32(f4) or stm32f7. +- compatible: can be either: + - "st,stm32-usart", + - "st,stm32-uart", + - "st,stm32f7-usart", + - "st,stm32f7-uart", + - "st,stm32h7-usart" + - "st,stm32h7-uart". + depending on whether the device supports synchronous mode + and is compatible with stm32(f4), stm32f7 or stm32h7. - reg: The address and length of the peripheral registers space -- interrupts: The interrupt line of the USART instance +- interrupts: + - The interrupt line for the USART instance, + - An optional wake-up interrupt. - clocks: The input clock of the USART instance Optional properties: |