diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 314 insertions, 17 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt index 49ccabbfa6f3..a4ff93d6b7f3 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/fsl,ls-scfg-msi.txt @@ -8,6 +8,7 @@ Required properties: "fsl,ls1043a-msi" "fsl,ls1046a-msi" "fsl,ls1043a-v1.1-msi" + "fsl,ls1012a-msi" - msi-controller: indicates that this is a PCIe MSI controller node - reg: physical base address of the controller and length of memory mapped. - interrupts: an interrupt to the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt new file mode 100644 index 000000000000..515b2f9542e5 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt @@ -0,0 +1,42 @@ +* Synopsys DesignWare PCIe root complex in ECAM shift mode + +In some cases, firmware may already have configured the Synopsys DesignWare +PCIe controller in RC mode with static ATU window mappings that cover all +config, MMIO and I/O spaces in a [mostly] ECAM compatible fashion. +In this case, there is no need for the OS to perform any low level setup +of clocks, PHYs or device registers, nor is there any reason for the driver +to reconfigure ATU windows for config and/or IO space accesses at runtime. + +In cases where the IP was synthesized with a minimum ATU window size of +64 KB, it cannot be supported by the generic ECAM driver, because it +requires special config space accessors that filter accesses to device #1 +and beyond on the first bus. + +Required properties: +- compatible: "marvell,armada8k-pcie-ecam" or + "socionext,synquacer-pcie-ecam" or + "snps,dw-pcie-ecam" (must be preceded by a more specific match) + +Please refer to the binding document of "pci-host-ecam-generic" in the +file host-generic-pci.txt for a description of the remaining required +and optional properties. + +Example: + + pcie1: pcie@7f000000 { + compatible = "socionext,synquacer-pcie-ecam", "snps,dw-pcie-ecam"; + device_type = "pci"; + reg = <0x0 0x7f000000 0x0 0xf00000>; + bus-range = <0x0 0xe>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x1000000 0x00 0x00010000 0x00 0x7ff00000 0x0 0x00010000>, + <0x2000000 0x00 0x70000000 0x00 0x70000000 0x0 0x0f000000>, + <0x3000000 0x3f 0x00000000 0x3f 0x00000000 0x1 0x00000000>; + + #interrupt-cells = <0x1>; + interrupt-map-mask = <0x0 0x0 0x0 0x0>; + interrupt-map = <0x0 0x0 0x0 0x0 &gic 0x0 0x0 0x0 182 0x4>; + msi-map = <0x0 &its 0x0 0x10000>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt new file mode 100644 index 000000000000..c84bc027930b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt @@ -0,0 +1,68 @@ +HiSilicon STB PCIe host bridge DT description + +The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core. +It shares common functions with the DesignWare PCIe core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Additional properties are described here: + +Required properties +- compatible: Should be one of the following strings: + "hisilicon,hi3798cv200-pcie" +- reg: Should contain sysctl, rc_dbi, config registers location and length. +- reg-names: Must include the following entries: + "control": control registers of PCIe controller; + "rc-dbi": configuration space of PCIe controller; + "config": configuration transaction space of PCIe controller. +- bus-range: PCI bus numbers covered. +- interrupts: MSI interrupt. +- interrupt-names: Must include "msi" entries. +- clocks: List of phandle and clock specifier pairs as listed in clock-names + property. +- clock-name: Must include the following entries: + "aux": auxiliary gate clock; + "pipe": pipe gate clock; + "sys": sys gate clock; + "bus": bus gate clock. +- resets: List of phandle and reset specifier pairs as listed in reset-names + property. +- reset-names: Must include the following entries: + "soft": soft reset; + "sys": sys reset; + "bus": bus reset. + +Optional properties: +- reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal. +- phys: List of phandle and phy mode specifier, should be 0. +- phy-names: Must be "phy". + +Example: + pcie@f9860000 { + compatible = "hisilicon,hi3798cv200-pcie"; + reg = <0xf9860000 0x1000>, + <0xf0000000 0x2000>, + <0xf2000000 0x01000000>; + reg-names = "control", "rc-dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0 15>; + num-lanes = <1>; + ranges=<0x81000000 0 0 0xf4000000 0 0x00010000 + 0x82000000 0 0xf3000000 0xf3000000 0 0x01000000>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg PCIE_AUX_CLK>, + <&crg PCIE_PIPE_CLK>, + <&crg PCIE_SYS_CLK>, + <&crg PCIE_BUS_CLK>; + clock-names = "aux", "pipe", "sys", "bus"; + resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>; + reset-names = "soft", "sys", "bus"; + phys = <&combphy1 PHY_TYPE_PCIE>; + phy-names = "phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index c0484da0f20d..66df1e81e0b8 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -18,6 +18,7 @@ Required properties: "fsl,ls2088a-pcie" "fsl,ls1088a-pcie" "fsl,ls1046a-pcie" + "fsl,ls1012a-pcie" - reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 1b4d2803dad1..145a4f04194f 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -1,10 +1,15 @@ NVIDIA Tegra PCIe controller Required properties: -- compatible: For Tegra20, must contain "nvidia,tegra20-pcie". For Tegra30, - "nvidia,tegra30-pcie". For Tegra124, must contain "nvidia,tegra124-pcie". - Otherwise, must contain "nvidia,<chip>-pcie", plus one of the above, where - <chip> is tegra132 or tegra210. +- compatible: Must be: + - "nvidia,tegra20-pcie": for Tegra20 + - "nvidia,tegra30-pcie": for Tegra30 + - "nvidia,tegra124-pcie": for Tegra124 and Tegra132 + - "nvidia,tegra210-pcie": for Tegra210 + - "nvidia,tegra186-pcie": for Tegra186 +- power-domains: To ungate power partition by BPMP powergate driver. Must + contain BPMP phandle and PCIe power partition ID. This is required only + for Tegra186. - device_type: Must be "pci" - reg: A list of physical base address and length for each set of controller registers. Must contain an entry for each entry in the reg-names property. @@ -124,6 +129,16 @@ Power supplies for Tegra210: - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must supply 1.8 V. +Power supplies for Tegra186: +- Required: + - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 1.8 V. + - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must + supply 1.8 V. + Root ports are defined as subnodes of the PCIe controller node. Required properties: @@ -546,3 +561,114 @@ Board DTS: status = "okay"; }; }; + +Tegra186: +--------- + +SoC DTSI: + + pcie@10003000 { + compatible = "nvidia,tegra186-pcie"; + power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>; + device_type = "pci"; + reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x10003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x40000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */ + 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */ + + clocks = <&bpmp TEGRA186_CLK_AFI>, + <&bpmp TEGRA186_CLK_PCIE>, + <&bpmp TEGRA186_CLK_PLLE>; + clock-names = "afi", "pex", "pll_e"; + + resets = <&bpmp TEGRA186_RESET_AFI>, + <&bpmp TEGRA186_RESET_PCIE>, + <&bpmp TEGRA186_RESET_PCIEXCLK>; + reset-names = "afi", "pex", "pcie_x"; + + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie@10003000 { + status = "okay"; + + dvdd-pex-supply = <&vdd_pex>; + hvdd-pex-pll-supply = <&vdd_1v8>; + hvdd-pex-supply = <&vdd_1v8>; + vddio-pexctl-aud-supply = <&vdd_1v8>; + + pci@1,0 { + nvidia,num-lanes = <4>; + status = "okay"; + }; + + pci@2,0 { + nvidia,num-lanes = <0>; + status = "disabled"; + }; + + pci@3,0 { + nvidia,num-lanes = <1>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt index 3d038638612b..9fe7e12a7bf3 100644 --- a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -60,17 +60,15 @@ Example SoC configuration: 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; - pci@0,1 { + usb@1,0 { reg = <0x800 0 0 0 0>; - device_type = "pci"; - phys = <&usbphy 0 0>; + phys = <&usb0 0>; phy-names = "usb"; }; - pci@0,2 { + usb@2,0 { reg = <0x1000 0 0 0 0>; - device_type = "pci"; - phys = <&usbphy 0 0>; + phys = <&usb0 0>; phy-names = "usb"; }; }; diff --git a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt index 30b364e504ba..11063293f761 100644 --- a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt +++ b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt @@ -2,14 +2,75 @@ V3 Semiconductor V360 EPC PCI bridge This bridge is found in the ARM Integrator/AP (Application Platform) -Integrator-specific notes: +Required properties: +- compatible: should be one of: + "v3,v360epc-pci" + "arm,integrator-ap-pci", "v3,v360epc-pci" +- reg: should contain two register areas: + first the base address of the V3 host bridge controller, 64KB + second the configuration area register space, 16MB +- interrupts: should contain a reference to the V3 error interrupt + as routed on the system. +- bus-range: see pci.txt +- ranges: this follows the standard PCI bindings in the IEEE Std + 1275-1994 (see pci.txt) with the following restriction: + - The non-prefetchable and prefetchable memory windows must + each be exactly 256MB (0x10000000) in size. + - The prefetchable memory window must be immediately adjacent + to the non-prefetcable memory window +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, + 64MB, 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked + as pre-fetchable. Two ranges are supported by the hardware. -- syscon: should contain a link to the syscon device node (since +Integrator-specific required properties: +- syscon: should contain a link to the syscon device node, since on the Integrator, some registers in the syscon are required to - operate the V3). + operate the V3 host bridge. -V360 EPC specific notes: +Example: -- reg: should contain the base address of the V3 adapter. -- interrupts: should contain a reference to the V3 error interrupt - as routed on the system. +pci: pciv3@62000000 { + compatible = "arm,integrator-ap-pci", "v3,v360epc-pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x62000000 0x10000>, <0x61000000 0x01000000>; + interrupt-parent = <&pic>; + interrupts = <17>; /* Bus error IRQ */ + clocks = <&pciclk>; + bus-range = <0x00 0xff>; + ranges = 0x01000000 0 0x00000000 /* I/O space @00000000 */ + 0x60000000 0 0x01000000 /* 16 MiB @ LB 60000000 */ + 0x02000000 0 0x40000000 /* non-prefectable memory @40000000 */ + 0x40000000 0 0x10000000 /* 256 MiB @ LB 40000000 1:1 */ + 0x42000000 0 0x50000000 /* prefetchable memory @50000000 */ + 0x50000000 0 0x10000000>; /* 256 MiB @ LB 50000000 1:1 */ + dma-ranges = <0x02000000 0 0x20000000 /* EBI memory space */ + 0x20000000 0 0x20000000 /* 512 MB @ LB 20000000 1:1 */ + 0x02000000 0 0x80000000 /* Core module alias memory */ + 0x80000000 0 0x40000000>; /* 1GB @ LB 80000000 */ + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = < + /* IDSEL 9 */ + 0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */ + 0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */ + 0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */ + 0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */ + /* IDSEL 10 */ + 0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */ + 0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */ + 0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */ + 0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */ + /* IDSEL 11 */ + 0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */ + 0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */ + 0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */ + 0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */ + /* IDSEL 12 */ + 0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */ + 0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */ + 0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */ + 0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */ + >; +}; |