diff options
Diffstat (limited to 'Documentation/devicetree')
7 files changed, 323 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt new file mode 100644 index 000000000000..5c80a7779552 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt @@ -0,0 +1,80 @@ +Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + +Optional properties: +- active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high. + If this property is missing, assume the VSEL pin is set to logic-low. + +Optional input supply properties: + - vp1-supply: The input supply for REG_DCDC1 + - vp2-supply: The input supply for REG_DCDC2 + - vp3-supply: The input supply for REG_DCDC3 + - inl45-supply: The input supply for REG_LDO1 and REG_LDO2 + - inl67-supply: The input supply for REG_LDO3 and REG_LDO4 + +Any standard regulator properties can be used to configure the single regulator. + +The valid names for regulators are: + REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 000000000000..14cfdc564159 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,29 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The Hi655x regulator control is managed by Hi655x PMIC. +So the node of this regulator must be child node of Hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2_2V8 LDO7_SDIO LDO10_2V85 LDO13_1V8 LDO14_2V8 +LDO15_1V8 LDO17_2V5 LDO19_3V0 LDO21_1V8 LDO22_1V2 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-name = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt index 78183182dad9..ca58a68ffdf1 100644 --- a/Documentation/devicetree/bindings/regulator/lp872x.txt +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -28,6 +28,7 @@ Optional properties: - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + - enable-gpios: GPIO specifier for EN pin control of LP872x devices. Sub nodes for regulator_init_data LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 09d796ed48be..879e98d3b9aa 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -60,7 +60,7 @@ The possible values for "regulator-initial-mode" and "regulator-mode" are: 1: Normal regulator voltage output mode. 3: Low Power which reduces the quiescent current down to only 1uA -The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +The valid modes list is defined in the dt-bindings/regulator/maxim,max77802.h header and can be included by device tree source files. The standard "regulator-mode" property can only be used for regulators that diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt new file mode 100644 index 000000000000..b3c8ca672024 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -0,0 +1,200 @@ +Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor. + +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply +of these regulators are defined under parent device node. +Details of regulator properties are defined as child node under +sub-node "regulators" which is child node of device node. + +Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt> +for common regulator bindings used by client. + +Following are properties of parent node related to regulators. + +Optional properties: +------------------- +The input supply of regulators are the optional properties on the +parent device node. The input supply of these regulators are provided +through following properties: +in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. +in-sd1-supply: Input supply for SD1. +in-sd2-supply: Input supply for SD2. +in-sd3-supply: Input supply for SD3. +in-ldo0-1-supply: Input supply for LDO0 and LDO1. +in-ldo2-supply: Input supply for LDO2. +in-ldo3-5-supply: Input supply for LDO3 and LDO5 +in-ldo4-6-supply: Input supply for LDO4 and LDO6. +in-ldo7-8-supply: Input supply for LDO7 and LDO8. + +Optional sub nodes for regulators under "regulators" subnode: +------------------------------------------------------------ +The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + +Each sub-node should contain the constraints and initialization +information for that regulator. The definition for each of these +nodes is defined using the standard binding for regulators found at +<Documentation/devicetree/bindings/regulator/regulator.txt>. + +Theres are also additional properties for SD/LDOs. These additional properties +are required to configure FPS configuration parameters for SDs and LDOs. +Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible +Power Sequence (FPS). +Following are additional properties: + +- maxim,active-fps-source: FPS source for the regulators to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + Regulator is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + regulator to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the regulator get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the regulator get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + regulators { + sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + }; + + sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 1d112fc456aa..ecfc593cac15 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -44,6 +44,11 @@ Optional properties: any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. - regulator-over-current-protection: Enable over current protection. +- regulator-active-discharge: tristate, enable/disable active discharge of + regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index e2cd1d7539e5..6e699ceabacd 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -33,12 +33,19 @@ Optional properties: Note that this is not needed in case the clocks are stable throughout the entire runtime of the codec. + - vd-supply: Digital power + - vl-supply: Logic power + - va-supply: Analog Power + Examples: codec_i2c: cs4271@10 { compatible = "cirrus,cs4271"; reg = <0x10>; reset-gpio = <&gpio 23 0>; + vd-supply = <&vdd_3v3_reg>; + vl-supply = <&vdd_3v3_reg>; + va-supply = <&vdd_3v3_reg>; }; codec_spi: cs4271@0 { |