diff options
Diffstat (limited to 'Documentation/devicetree')
11 files changed, 244 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt new file mode 100644 index 000000000000..597e8a089fe4 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt @@ -0,0 +1,27 @@ +* TI Common Platform Interrupt Controller + +Common Platform Interrupt Controller (cp_intc) is used on +OMAP-L1x SoCs and can support several configurable number +of interrupts. + +Main node required properties: + +- compatible : should be: + "ti,cp-intc" +- interrupt-controller : Identifies the node as an interrupt controller +- #interrupt-cells : Specifies the number of cells needed to encode an + interrupt source. The type shall be a <u32> and the value shall be 1. + + The cell contains the interrupt number in the range [0-128]. +- ti,intc-size: Number of interrupts handled by the interrupt controller. +- reg: physical base address and size of the intc registers map. + +Example: + + intc: interrupt-controller@1 { + compatible = "ti,cp-intc"; + interrupt-controller; + #interrupt-cells = <1>; + ti,intc-size = <101>; + reg = <0xfffee000 0x2000>; + }; diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt new file mode 100644 index 000000000000..007fb5c685a1 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/olimex.txt @@ -0,0 +1,6 @@ +Olimex i.MX Platforms Device Tree Bindings +------------------------------------------ + +i.MX23 Olinuxino Low Cost Board +Required root node properties: + - compatible = "olimex,imx23-olinuxino", "fsl,imx23"; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index e78e8bccac30..f186167dba9e 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -47,3 +47,6 @@ Boards: - AM335X EVM : Software Developement Board for AM335x compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" + +- AM335X Bone : Low cost community board + compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3" diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt new file mode 100644 index 000000000000..b41e5e52a676 --- /dev/null +++ b/Documentation/devicetree/bindings/fb/mxsfb.txt @@ -0,0 +1,19 @@ +* Freescale MXS LCD Interface (LCDIF) + +Required properties: +- compatible: Should be "fsl,<chip>-lcdif". Supported chips include + imx23 and imx28. +- reg: Address and length of the register set for lcdif +- interrupts: Should contain lcdif interrupts + +Optional properties: +- panel-enable-gpios : Should specify the gpio for panel enable + +Examples: + +lcdif@80030000 { + compatible = "fsl,imx28-lcdif"; + reg = <0x80030000 2000>; + interrupts = <38 86>; + panel-enable-gpios = <&gpio3 30 0>; +}; diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt index 4363ae4b3c14..4f3929713ae4 100644 --- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt @@ -8,8 +8,16 @@ Required properties: by low 16 pins and the second one is for high 16 pins. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells : Should be 2. The first cell is the GPIO number. + The second cell bits[3:0] is used to specify trigger type and level flags: + 1 = low-to-high edge triggered. + 2 = high-to-low edge triggered. + 4 = active high level-sensitive. + 8 = active low level-sensitive. Example: @@ -19,4 +27,6 @@ gpio0: gpio@73f84000 { interrupts = <50 51>; gpio-controller; #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt index 0c35673f7a3e..1e677a47b836 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt @@ -13,8 +13,9 @@ Required properties for GPIO node: - interrupts : Should be the port interrupt shared by all 32 pins. - gpio-controller : Marks the device node as a gpio controller. - #gpio-cells : Should be two. The first cell is the pin number and - the second cell is used to specify optional parameters (currently - unused). + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low - interrupt-controller: Marks the device node as an interrupt controller. - #interrupt-cells : Should be 2. The first cell is the GPIO number. The second cell bits[3:0] is used to specify trigger type and level flags: diff --git a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt index ee87467ad8d6..8315ac7780ef 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-nmk.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-nmk.txt @@ -26,6 +26,6 @@ Example: #gpio-cells = <2>; gpio-controller; interrupt-controller; - supports-sleepmode; + st,supports-sleepmode; gpio-bank = <1>; }; diff --git a/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt b/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt new file mode 100644 index 000000000000..b800070fe6e9 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/stmp3xxx-rtc.txt @@ -0,0 +1,16 @@ +* STMP3xxx/i.MX28 Time Clock controller + +Required properties: +- compatible: should be one of the following. + * "fsl,stmp3xxx-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: rtc alarm interrupt + +Example: + +rtc@80056000 { + compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc"; + reg = <0x80056000 2000>; + interrupts = <29>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt new file mode 100644 index 000000000000..a15ffeddfba4 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -0,0 +1,116 @@ +* Samsung SPI Controller + +The Samsung SPI controller is used to interface with various devices such as flash +and display controllers using the SPI communication interface. + +Required SoC Specific Properties: + +- compatible: should be one of the following. + - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms + - samsung,s3c6410-spi: for s3c6410 platforms + - samsung,s5p6440-spi: for s5p6440 and s5p6450 platforms + - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms + - samsung,exynos4210-spi: for exynos4 and exynos5 platforms + +- reg: physical base address of the controller and length of memory mapped + region. + +- interrupts: The interrupt number to the cpu. The interrupt specifier format + depends on the interrupt controller. + +[PRELIMINARY: the dma channel allocation will change once there are +official DMA bindings] + +- tx-dma-channel: The dma channel specifier for tx operations. The format of + the dma specifier depends on the dma controller. + +- rx-dma-channel: The dma channel specifier for rx operations. The format of + the dma specifier depends on the dma controller. + +Required Board Specific Properties: + +- #address-cells: should be 1. +- #size-cells: should be 0. +- gpios: The gpio specifier for clock, mosi and miso interface lines (in the + order specified). The format of the gpio specifier depends on the gpio + controller. + +Optional Board Specific Properties: + +- samsung,spi-src-clk: If the spi controller includes a internal clock mux to + select the clock source for the spi bus clock, this property can be used to + indicate the clock to be used for driving the spi bus clock. If not specified, + the clock number 0 is used as default. + +- num-cs: Specifies the number of chip select lines supported. If + not specified, the default number of chip select lines is set to 1. + +SPI Controller specific data in SPI slave nodes: + +- The spi slave nodes should provide the following information which is required + by the spi controller. + + - cs-gpio: A gpio specifier that specifies the gpio line used as + the slave select line by the spi controller. The format of the gpio + specifier depends on the gpio controller. + + - samsung,spi-feedback-delay: The sampling phase shift to be applied on the + miso line (to account for any lag in the miso line). The following are the + valid values. + + - 0: No phase shift. + - 1: 90 degree phase shift sampling. + - 2: 180 degree phase shift sampling. + - 3: 270 degree phase shift sampling. + +Aliases: + +- All the SPI controller nodes should be represented in the aliases node using + the following format 'spi{n}' where n is a unique number for the alias. + + +Example: + +- SoC Specific Portion: + + spi_0: spi@12d20000 { + compatible = "samsung,exynos4210-spi"; + reg = <0x12d20000 0x100>; + interrupts = <0 66 0>; + tx-dma-channel = <&pdma0 5>; + rx-dma-channel = <&pdma0 4>; + }; + +- Board Specific Portion: + + spi_0: spi@12d20000 { + #address-cells = <1>; + #size-cells = <0>; + gpios = <&gpa2 4 2 3 0>, + <&gpa2 6 2 3 0>, + <&gpa2 7 2 3 0>; + + w25q80bw@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "w25x80"; + reg = <0>; + spi-max-frequency = <10000>; + + controller-data { + cs-gpio = <&gpa2 5 1 0 3>; + samsung,spi-feedback-delay = <0>; + }; + + partition@0 { + label = "U-Boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "Kernel"; + reg = <0x40000 0xc0000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt new file mode 100644 index 000000000000..2ee903fad25c --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt @@ -0,0 +1,27 @@ +* Freescale MXS Application UART (AUART) + +Required properties: +- compatible : Should be "fsl,<soc>-auart". The supported SoCs include + imx23 and imx28. +- reg : Address and length of the register set for the device +- interrupts : Should contain the auart interrupt numbers + +Example: +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112 70 71>; +}; + +Note: Each auart port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + serial0 = &auart0; + serial1 = &auart1; + serial2 = &auart2; + serial3 = &auart3; + serial4 = &auart4; +}; diff --git a/Documentation/devicetree/bindings/watchdog/omap-wdt.txt b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt new file mode 100644 index 000000000000..c227970671ea --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/omap-wdt.txt @@ -0,0 +1,14 @@ +TI Watchdog Timer (WDT) Controller for OMAP + +Required properties: +compatible: +- "ti,omap3-wdt" for OMAP3 +- "ti,omap4-wdt" for OMAP4 +- ti,hwmods: Name of the hwmod associated to the WDT + +Examples: + +wdt2: wdt@4a314000 { + compatible = "ti,omap4-wdt", "ti,omap3-wdt"; + ti,hwmods = "wd_timer2"; +}; |