diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
4 files changed, 114 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt new file mode 100644 index 000000000000..936fbdf12815 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.txt @@ -0,0 +1,27 @@ +* PTN5150 CC (Configuration Channel) Logic device + +PTN5150 is a small thin low power CC logic chip supporting the USB Type-C +connector application with CC control logic detection and indication functions. +It is interfaced to the host controller using an I2C interface. + +Required properties: +- compatible: should be "nxp,ptn5150" +- reg: specifies the I2C slave address of the device +- int-gpio: should contain a phandle and GPIO specifier for the GPIO pin + connected to the PTN5150's INTB pin. +- vbus-gpio: should contain a phandle and GPIO specifier for the GPIO pin which + is used to control VBUS. +- pinctrl-names : a pinctrl state named "default" must be defined. +- pinctrl-0 : phandle referencing pin configuration of interrupt and vbus + control. + +Example: + ptn5150@1d { + compatible = "nxp,ptn5150"; + reg = <0x1d>; + int-gpio = <&msmgpio 78 GPIO_ACTIVE_HIGH>; + vbus-gpio = <&msmgpio 148 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&ptn5150_default>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/interconnect/interconnect.txt b/Documentation/devicetree/bindings/interconnect/interconnect.txt new file mode 100644 index 000000000000..5a3c575b387a --- /dev/null +++ b/Documentation/devicetree/bindings/interconnect/interconnect.txt @@ -0,0 +1,60 @@ +Interconnect Provider Device Tree Bindings +========================================= + +The purpose of this document is to define a common set of generic interconnect +providers/consumers properties. + + += interconnect providers = + +The interconnect provider binding is intended to represent the interconnect +controllers in the system. Each provider registers a set of interconnect +nodes, which expose the interconnect related capabilities of the interconnect +to consumer drivers. These capabilities can be throughput, latency, priority +etc. The consumer drivers set constraints on interconnect path (or endpoints) +depending on the use case. Interconnect providers can also be interconnect +consumers, such as in the case where two network-on-chip fabrics interface +directly. + +Required properties: +- compatible : contains the interconnect provider compatible string +- #interconnect-cells : number of cells in a interconnect specifier needed to + encode the interconnect node id + +Example: + + snoc: interconnect@580000 { + compatible = "qcom,msm8916-snoc"; + #interconnect-cells = <1>; + reg = <0x580000 0x14000>; + clock-names = "bus_clk", "bus_a_clk"; + clocks = <&rpmcc RPM_SMD_SNOC_CLK>, + <&rpmcc RPM_SMD_SNOC_A_CLK>; + }; + + += interconnect consumers = + +The interconnect consumers are device nodes which dynamically express their +bandwidth requirements along interconnect paths they are connected to. There +can be multiple interconnect providers on a SoC and the consumer may consume +multiple paths from different providers depending on use case and the +components it has to interact with. + +Required properties: +interconnects : Pairs of phandles and interconnect provider specifier to denote + the edge source and destination ports of the interconnect path. + +Optional properties: +interconnect-names : List of interconnect path name strings sorted in the same + order as the interconnects property. Consumers drivers will use + interconnect-names to match interconnect paths with interconnect + specifier pairs. + +Example: + + sdhci@7864000 { + ... + interconnects = <&pnoc MASTER_SDCC_1 &bimc SLAVE_EBI_CH0>; + interconnect-names = "sdhc-mem"; + }; diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt new file mode 100644 index 000000000000..5c4f1d911630 --- /dev/null +++ b/Documentation/devicetree/bindings/interconnect/qcom,sdm845.txt @@ -0,0 +1,24 @@ +Qualcomm SDM845 Network-On-Chip interconnect driver binding +----------------------------------------------------------- + +SDM845 interconnect providers support system bandwidth requirements through +RPMh hardware accelerators known as Bus Clock Manager (BCM). The provider is +able to communicate with the BCM through the Resource State Coordinator (RSC) +associated with each execution environment. Provider nodes must reside within +an RPMh device node pertaining to their RSC and each provider maps to a single +RPMh resource. + +Required properties : +- compatible : shall contain only one of the following: + "qcom,sdm845-rsc-hlos" +- #interconnect-cells : should contain 1 + +Examples: + +apps_rsc: rsc { + rsc_hlos: interconnect { + compatible = "qcom,sdm845-rsc-hlos"; + #interconnect-cells = <1>; + }; +}; + diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt index 792bc5fafeb9..7a999a135e56 100644 --- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.txt @@ -1,7 +1,7 @@ Freescale i.MX6 On-Chip OTP Controller (OCOTP) device tree bindings This binding represents the on-chip eFuse OTP controller found on -i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL and i.MX6SLL SoCs. +i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL, i.MX6ULL/ULZ and i.MX6SLL SoCs. Required properties: - compatible: should be one of @@ -9,8 +9,10 @@ Required properties: "fsl,imx6sl-ocotp" (i.MX6SL), or "fsl,imx6sx-ocotp" (i.MX6SX), "fsl,imx6ul-ocotp" (i.MX6UL), + "fsl,imx6ull-ocotp" (i.MX6ULL/ULZ), "fsl,imx7d-ocotp" (i.MX7D/S), "fsl,imx6sll-ocotp" (i.MX6SLL), + "fsl,imx7ulp-ocotp" (i.MX7ULP), followed by "syscon". - #address-cells : Should be 1 - #size-cells : Should be 1 |