diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
31 files changed, 958 insertions, 147 deletions
diff --git a/Documentation/devicetree/bindings/clock/adi,axi-clkgen.yaml b/Documentation/devicetree/bindings/clock/adi,axi-clkgen.yaml new file mode 100644 index 000000000000..0d06387184d6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/adi,axi-clkgen.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/adi,axi-clkgen.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for Analog Devices AXI clkgen pcore clock generator + +maintainers: + - Lars-Peter Clausen <lars@metafoo.de> + - Michael Hennerich <michael.hennerich@analog.com> + +description: | + The axi_clkgen IP core is a software programmable clock generator, + that can be synthesized on various FPGA platforms. + + Link: https://wiki.analog.com/resources/fpga/docs/axi_clkgen + +properties: + compatible: + enum: + - adi,axi-clkgen-2.00.a + + clocks: + description: + Specifies the reference clock(s) from which the output frequency is + derived. This must either reference one clock if only the first clock + input is connected or two if both clock inputs are connected. + minItems: 1 + maxItems: 2 + + '#clock-cells': + const: 0 + + reg: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - '#clock-cells' + +additionalProperties: false + +examples: + - | + clock-controller@ff000000 { + compatible = "adi,axi-clkgen-2.00.a"; + #clock-cells = <0>; + reg = <0xff000000 0x1000>; + clocks = <&osc 1>; + }; diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt deleted file mode 100644 index aca94fe9416f..000000000000 --- a/Documentation/devicetree/bindings/clock/axi-clkgen.txt +++ /dev/null @@ -1,25 +0,0 @@ -Binding for the axi-clkgen clock generator - -This binding uses the common clock binding[1]. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt - -Required properties: -- compatible : shall be "adi,axi-clkgen-1.00.a" or "adi,axi-clkgen-2.00.a". -- #clock-cells : from common clock binding; Should always be set to 0. -- reg : Address and length of the axi-clkgen register set. -- clocks : Phandle and clock specifier for the parent clock(s). This must - either reference one clock if only the first clock input is connected or two - if both clock inputs are connected. For the later case the clock connected - to the first input must be specified first. - -Optional properties: -- clock-output-names : From common clock binding. - -Example: - clock@ff000000 { - compatible = "adi,axi-clkgen"; - #clock-cells = <0>; - reg = <0xff000000 0x1000>; - clocks = <&osc 1>; - }; diff --git a/Documentation/devicetree/bindings/clock/canaan,k210-clk.yaml b/Documentation/devicetree/bindings/clock/canaan,k210-clk.yaml new file mode 100644 index 000000000000..565ca468cb44 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/canaan,k210-clk.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/canaan,k210-clk.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Canaan Kendryte K210 Clock Device Tree Bindings + +maintainers: + - Damien Le Moal <damien.lemoal@wdc.com> + +description: | + Canaan Kendryte K210 SoC clocks driver bindings. The clock + controller node must be defined as a child node of the K210 + system controller node. + + See also: + - dt-bindings/clock/k210-clk.h + +properties: + compatible: + const: canaan,k210-clk + + clocks: + description: + Phandle of the SoC 26MHz fixed-rate oscillator clock. + + '#clock-cells': + const: 1 + +required: + - compatible + - '#clock-cells' + - clocks + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/k210-clk.h> + clocks { + in0: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + }; + + /* ... */ + sysclk: clock-controller { + #clock-cells = <1>; + compatible = "canaan,k210-clk"; + clocks = <&in0>; + }; diff --git a/Documentation/devicetree/bindings/clock/fsl,flexspi-clock.yaml b/Documentation/devicetree/bindings/clock/fsl,flexspi-clock.yaml new file mode 100644 index 000000000000..1fa390ee7b9b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fsl,flexspi-clock.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/fsl,flexspi-clock.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale FlexSPI clock driver for Layerscape SoCs + +maintainers: + - Michael Walle <michael@walle.cc> + +description: + The Freescale Layerscape SoCs have a special FlexSPI clock which is + derived from the platform PLL. + +properties: + compatible: + enum: + - fsl,ls1028a-flexspi-clk + - fsl,lx2160a-flexspi-clk + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + '#clock-cells': + const: 0 + + clock-output-names: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - '#clock-cells' + +additionalProperties: false + +examples: + - | + dcfg { + #address-cells = <1>; + #size-cells = <1>; + + fspi_clk: clock-controller@900 { + compatible = "fsl,ls1028a-flexspi-clk"; + reg = <0x900 0x4>; + #clock-cells = <0>; + clocks = <&parentclk>; + clock-output-names = "fspi_clk"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,aoncc-sm8250.yaml b/Documentation/devicetree/bindings/clock/qcom,aoncc-sm8250.yaml new file mode 100644 index 000000000000..c40a74b5d672 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,aoncc-sm8250.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,aoncc-sm8250.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Clock bindings for LPASS Always ON Clock Controller on SM8250 SoCs + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + The clock consumer should specify the desired clock by having the clock + ID in its "clocks" phandle cell. + See include/dt-bindings/clock/qcom,sm8250-lpass-aoncc.h for the full list + of Audio Clock controller clock IDs. + +properties: + compatible: + const: qcom,sm8250-lpass-aon + + reg: + maxItems: 1 + + '#clock-cells': + const: 1 + + clocks: + items: + - description: LPASS Core voting clock + - description: Glitch Free Mux register clock + + clock-names: + items: + - const: core + - const: bus + +required: + - compatible + - reg + - '#clock-cells' + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sm8250-lpass-aoncc.h> + #include <dt-bindings/sound/qcom,q6afe.h> + clock-controller@3800000 { + #clock-cells = <1>; + compatible = "qcom,sm8250-lpass-aon"; + reg = <0x03380000 0x40000>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "bus"; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,audiocc-sm8250.yaml b/Documentation/devicetree/bindings/clock/qcom,audiocc-sm8250.yaml new file mode 100644 index 000000000000..915d76206ad0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,audiocc-sm8250.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,audiocc-sm8250.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Clock bindings for LPASS Audio Clock Controller on SM8250 SoCs + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + +description: | + The clock consumer should specify the desired clock by having the clock + ID in its "clocks" phandle cell. + See include/dt-bindings/clock/qcom,sm8250-lpass-audiocc.h for the full list + of Audio Clock controller clock IDs. + +properties: + compatible: + const: qcom,sm8250-lpass-audiocc + + reg: + maxItems: 1 + + '#clock-cells': + const: 1 + + clocks: + items: + - description: LPASS Core voting clock + - description: Glitch Free Mux register clock + + clock-names: + items: + - const: core + - const: bus + +required: + - compatible + - reg + - '#clock-cells' + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sm8250-lpass-audiocc.h> + #include <dt-bindings/sound/qcom,q6afe.h> + clock-controller@3300000 { + #clock-cells = <1>; + compatible = "qcom,sm8250-lpass-audiocc"; + reg = <0x03300000 0x30000>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "bus"; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc-sdx55.yaml b/Documentation/devicetree/bindings/clock/qcom,gcc-sdx55.yaml new file mode 100644 index 000000000000..1121b3934cb9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,gcc-sdx55.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,gcc-sdx55.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Global Clock & Reset Controller Binding for SDX55 + +maintainers: + - Vinod Koul <vkoul@kernel.org> + - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + +description: | + Qualcomm global clock control module which supports the clocks, resets and + power domains on SDX55 + + See also: + - dt-bindings/clock/qcom,gcc-sdx55.h + +properties: + compatible: + const: qcom,gcc-sdx55 + + clocks: + items: + - description: Board XO source + - description: Sleep clock source + - description: PLL test clock source (Optional clock) + minItems: 2 + maxItems: 3 + + clock-names: + items: + - const: bi_tcxo + - const: sleep_clk + - const: core_bi_pll_test_se # Optional clock + minItems: 2 + maxItems: 3 + + '#clock-cells': + const: 1 + + '#reset-cells': + const: 1 + + '#power-domain-cells': + const: 1 + + reg: + maxItems: 1 + +required: + - compatible + - clocks + - clock-names + - reg + - '#clock-cells' + - '#reset-cells' + - '#power-domain-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + clock-controller@100000 { + compatible = "qcom,gcc-sdx55"; + reg = <0x00100000 0x1f0000>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&sleep_clk>, <&pll_test_clk>; + clock-names = "bi_tcxo", "sleep_clk", "core_bi_pll_test_se"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml b/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml index a46a3a799a70..12c9cbc0ebf9 100644 --- a/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml +++ b/Documentation/devicetree/bindings/clock/qcom,rpmhcc.yaml @@ -19,8 +19,10 @@ properties: enum: - qcom,sc7180-rpmh-clk - qcom,sdm845-rpmh-clk + - qcom,sdx55-rpmh-clk - qcom,sm8150-rpmh-clk - qcom,sm8250-rpmh-clk + - qcom,sm8350-rpmh-clk clocks: maxItems: 1 diff --git a/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml b/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml new file mode 100644 index 000000000000..f49027edfc44 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,sc7180-camcc.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,sc7180-camcc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Camera Clock & Reset Controller Binding for SC7180 + +maintainers: + - Taniya Das <tdas@codeaurora.org> + +description: | + Qualcomm camera clock control module which supports the clocks, resets and + power domains on SC7180. + + See also: + - dt-bindings/clock/qcom,camcc-sc7180.h + +properties: + compatible: + const: qcom,sc7180-camcc + + clocks: + items: + - description: Board XO source + - description: Camera_ahb clock from GCC + - description: Camera XO clock from GCC + + clock-names: + items: + - const: bi_tcxo + - const: iface + - const: xo + + '#clock-cells': + const: 1 + + '#reset-cells': + const: 1 + + '#power-domain-cells': + const: 1 + + reg: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + - '#reset-cells' + - '#power-domain-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sc7180.h> + #include <dt-bindings/clock/qcom,rpmh.h> + clock-controller@ad00000 { + compatible = "qcom,sc7180-camcc"; + reg = <0x0ad00000 0x10000>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_CAMERA_AHB_CLK>, + <&gcc GCC_CAMERA_XO_CLK>; + clock-names = "bi_tcxo", "iface", "xo"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; +... diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt deleted file mode 100644 index da92f5748dee..000000000000 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt +++ /dev/null @@ -1,68 +0,0 @@ -* Renesas R-Car USB 2.0 clock selector - -This file provides information on what the device node for the R-Car USB 2.0 -clock selector. - -If you connect an external clock to the USB_EXTAL pin only, you should set -the clock rate to "usb_extal" node only. -If you connect an oscillator to both the USB_XTAL and USB_EXTAL, this module -is not needed because this is default setting. (Of course, you can set the -clock rates to both "usb_extal" and "usb_xtal" nodes. - -Case 1: An external clock connects to R-Car SoC - +----------+ +--- R-Car ---------------------+ - |External |---|USB_EXTAL ---> all usb channels| - |clock | |USB_XTAL | - +----------+ +-------------------------------+ -In this case, we need this driver with "usb_extal" clock. - -Case 2: An oscillator connects to R-Car SoC - +----------+ +--- R-Car ---------------------+ - |Oscillator|---|USB_EXTAL -+-> all usb channels| - | |---|USB_XTAL --+ | - +----------+ +-------------------------------+ -In this case, we don't need this selector. - -Required properties: -- compatible: "renesas,r8a7795-rcar-usb2-clock-sel" if the device is a part of - an R8A7795 SoC. - "renesas,r8a7796-rcar-usb2-clock-sel" if the device if a part of - an R8A77960 SoC. - "renesas,r8a77961-rcar-usb2-clock-sel" if the device if a part of - an R8A77961 SoC. - "renesas,rcar-gen3-usb2-clock-sel" for a generic R-Car Gen3 - compatible device. - - When compatible with the generic version, nodes must list the - SoC-specific version corresponding to the platform first - followed by the generic version. - -- reg: offset and length of the USB 2.0 clock selector register block. -- clocks: A list of phandles and specifier pairs. -- clock-names: Name of the clocks. - - The functional clock of USB 2.0 host side must be "ehci_ohci" - - The functional clock of HS-USB side must be "hs-usb-if" - - The USB_EXTAL clock pin must be "usb_extal" - - The USB_XTAL clock pin must be "usb_xtal" -- #clock-cells: Must be 0 -- power-domains: A phandle and symbolic PM domain specifier. - See power/renesas,rcar-sysc.yaml. -- resets: A list of phandles and specifier pairs. -- reset-names: Name of the resets. - - The reset of USB 2.0 host side must be "ehci_ohci" - - The reset of HS-USB side must be "hs-usb-if" - -Example (R-Car H3): - - usb2_clksel: clock-controller@e6590630 { - compatible = "renesas,r8a7795-rcar-usb2-clock-sel", - "renesas,rcar-gen3-usb2-clock-sel"; - reg = <0 0xe6590630 0 0x02>; - clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, - <&usb_extal>, <&usb_xtal>; - clock-names = "ehci_ohci", "hs-usb-if", "usb_extal", "usb_xtal"; - #clock-cells = <0>; - power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; - resets = <&cpg 703>, <&cpg 704>; - reset-names = "ehci_ohci", "hs-usb-if"; - }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.yaml b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.yaml new file mode 100644 index 000000000000..5be1229b3d6e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.yaml @@ -0,0 +1,100 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/clock/renesas,rcar-usb2-clock-sel.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Renesas R-Car USB 2.0 clock selector + +maintainers: + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +description: | + If you connect an external clock to the USB_EXTAL pin only, you should set + the clock rate to "usb_extal" node only. + If you connect an oscillator to both the USB_XTAL and USB_EXTAL, this module + is not needed because this is default setting. (Of course, you can set the + clock rates to both "usb_extal" and "usb_xtal" nodes. + + Case 1: An external clock connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |External |---|USB_EXTAL ---> all usb channels| + |clock | |USB_XTAL | + +----------+ +-------------------------------+ + + In this case, we need this driver with "usb_extal" clock. + + Case 2: An oscillator connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |Oscillator|---|USB_EXTAL -+-> all usb channels| + | |---|USB_XTAL --+ | + +----------+ +-------------------------------+ + In this case, we don't need this selector. + +properties: + compatible: + items: + - enum: + - renesas,r8a7795-rcar-usb2-clock-sel # R-Car H3 + - renesas,r8a7796-rcar-usb2-clock-sel # R-Car M3-W + - renesas,r8a77961-rcar-usb2-clock-sel # R-Car M3-W+ + - const: renesas,rcar-gen3-usb2-clock-sel + + reg: + maxItems: 1 + + clocks: + minItems: 4 + maxItems: 4 + + clock-names: + items: + - const: ehci_ohci + - const: hs-usb-if + - const: usb_extal + - const: usb_xtal + + '#clock-cells': + const: 0 + + power-domains: + maxItems: 1 + + resets: + minItems: 2 + maxItems: 2 + + reset-names: + items: + - const: ehci_ohci + - const: hs-usb-if + +required: + - compatible + - reg + - clocks + - clock-names + - '#clock-cells' + - power-domains + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a7795-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0xe6590630 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal>, <&usb_xtal>; + clock-names = "ehci_ohci", "hs-usb-if", "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + }; diff --git a/Documentation/devicetree/bindings/clock/sifive/fu740-prci.yaml b/Documentation/devicetree/bindings/clock/sifive/fu740-prci.yaml new file mode 100644 index 000000000000..e17143cac316 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sifive/fu740-prci.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 SiFive, Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/sifive/fu740-prci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive FU740 Power Reset Clock Interrupt Controller (PRCI) + +maintainers: + - Zong Li <zong.li@sifive.com> + - Paul Walmsley <paul.walmsley@sifive.com> + +description: + On the FU740 family of SoCs, most system-wide clock and reset integration + is via the PRCI IP block. + The clock consumer should specify the desired clock via the clock ID + macros defined in include/dt-bindings/clock/sifive-fu740-prci.h. + These macros begin with PRCI_CLK_. + + The hfclk and rtcclk nodes are required, and represent physical + crystals or resonators located on the PCB. These nodes should be present + underneath /, rather than /soc. + +properties: + compatible: + const: sifive,fu740-c000-prci + + reg: + maxItems: 1 + + clocks: + items: + - description: high frequency clock. + - description: RTL clock. + + clock-names: + items: + - const: hfclk + - const: rtcclk + + "#clock-cells": + const: 1 + +required: + - compatible + - reg + - clocks + - "#clock-cells" + +additionalProperties: false + +examples: + - | + prci: clock-controller@10000000 { + compatible = "sifive,fu740-c000-prci"; + reg = <0x10000000 0x1000>; + clocks = <&hfclk>, <&rtcclk>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml index f9750b0b6708..27fffafe5b5c 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml @@ -159,6 +159,8 @@ properties: - innolux,g121x1-l03 # Innolux Corporation 11.6" WXGA (1366x768) TFT LCD panel - innolux,n116bge + # InnoLux 13.3" FHD (1920x1080) eDP TFT LCD panel + - innolux,n125hce-gn1 # InnoLux 15.6" WXGA TFT LCD panel - innolux,n156bge-l21 # Innolux Corporation 7.0" WSVGA (1024x600) TFT LCD panel diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml b/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml index 183ec23eda39..f5ee23c2df60 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml +++ b/Documentation/devicetree/bindings/gpio/gpio-pca95xx.yaml @@ -48,6 +48,7 @@ properties: - nxp,pcal6416 - nxp,pcal6524 - nxp,pcal9535 + - nxp,pcal9554b - nxp,pcal9555a - onnn,cat9554 - onnn,pca9654 diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt index 08eed2335db0..e506f30e1a95 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt @@ -13,6 +13,7 @@ Required properties: - gpio-controller : Marks the device node as a GPIO controller. Optional properties: +- clocks : Input clock specifier. Refer to common clock bindings. - interrupts : Interrupt mapping for GPIO IRQ. - xlnx,all-inputs : if n-th bit is setup, GPIO-n is input - xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1 @@ -29,6 +30,7 @@ Example: gpio: gpio@40000000 { #gpio-cells = <2>; compatible = "xlnx,xps-gpio-1.00.a"; + clocks = <&clkc25>; gpio-controller ; interrupt-parent = <µblaze_0_intc>; interrupts = < 6 2 >; diff --git a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt deleted file mode 100644 index e1c49b660d3a..000000000000 --- a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt +++ /dev/null @@ -1,35 +0,0 @@ -Mediatek MT7621 SoC GPIO controller bindings - -The IP core used inside these SoCs has 3 banks of 32 GPIOs each. -The registers of all the banks are interwoven inside one single IO range. -We load one GPIO controller instance per bank. Also the GPIO controller can receive -interrupts on any of the GPIOs, either edge or level. It then interrupts the CPU -using GIC INT12. - -Required properties for the top level node: -- #gpio-cells : Should be two. The first cell is the GPIO pin number and the - second cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. - Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. -- #interrupt-cells : Specifies the number of cells needed to encode an - interrupt. Should be 2. The first cell defines the interrupt number, - the second encodes the trigger flags encoded as described in - Documentation/devicetree/bindings/interrupt-controller/interrupts.txt -- compatible: - - "mediatek,mt7621-gpio" for Mediatek controllers -- reg : Physical base address and length of the controller's registers -- interrupt-parent : phandle of the parent interrupt controller. -- interrupts : Interrupt specifier for the controllers interrupt. -- interrupt-controller : Mark the device node as an interrupt controller. -- gpio-controller : Marks the device node as a GPIO controller. - -Example: - gpio@600 { - #gpio-cells = <2>; - #interrupt-cells = <2>; - compatible = "mediatek,mt7621-gpio"; - gpio-controller; - interrupt-controller; - reg = <0x600 0x100>; - interrupt-parent = <&gic>; - interrupts = <GIC_SHARED 12 IRQ_TYPE_LEVEL_HIGH>; - }; diff --git a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.yaml b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.yaml new file mode 100644 index 000000000000..5bbb2a31266e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/mediatek,mt7621-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT7621 SoC GPIO controller + +maintainers: + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +description: | + The IP core used inside these SoCs has 3 banks of 32 GPIOs each. + The registers of all the banks are interwoven inside one single IO range. + We load one GPIO controller instance per bank. Also the GPIO controller can receive + interrupts on any of the GPIOs, either edge or level. It then interrupts the CPU + using GIC INT12. + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + const: mediatek,mt7621-gpio + + reg: + maxItems: 1 + + "#gpio-cells": + const: 2 + + gpio-controller: true + gpio-ranges: true + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - "#gpio-cells" + - gpio-controller + - gpio-ranges + - interrupt-controller + - "#interrupt-cells" + - interrupts + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/interrupt-controller/mips-gic.h> + + gpio@600 { + compatible = "mediatek,mt7621-gpio"; + reg = <0x600 0x100>; + #gpio-cells = <2>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 95>; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + interrupts = <GIC_SHARED 12 IRQ_TYPE_LEVEL_HIGH>; + }; + +... diff --git a/Documentation/devicetree/bindings/gpio/mstar,msc313-gpio.yaml b/Documentation/devicetree/bindings/gpio/mstar,msc313-gpio.yaml new file mode 100644 index 000000000000..1f2ef408bb43 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/mstar,msc313-gpio.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/mstar,msc313-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MStar/SigmaStar GPIO controller + +maintainers: + - Daniel Palmer <daniel@thingy.jp> + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + const: mstar,msc313-gpio + + reg: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + + gpio-ranges: true + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + +required: + - compatible + - reg + - gpio-controller + - "#gpio-cells" + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/msc313-gpio.h> + + gpio: gpio@207800 { + compatible = "mstar,msc313e-gpio"; + #gpio-cells = <2>; + reg = <0x207800 0x200>; + gpio-controller; + gpio-ranges = <&pinctrl 0 36 22>, + <&pinctrl 22 63 4>, + <&pinctrl 26 68 6>; + #interrupt-cells = <2>; + interrupt-controller; + interrupt-parent = <&intc_fiq>; + }; diff --git a/Documentation/devicetree/bindings/i3c/mipi-i3c-hci.yaml b/Documentation/devicetree/bindings/i3c/mipi-i3c-hci.yaml new file mode 100644 index 000000000000..07a7b10163a3 --- /dev/null +++ b/Documentation/devicetree/bindings/i3c/mipi-i3c-hci.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/i3c/mipi-i3c-hci.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: MIPI I3C HCI Device Tree Bindings + +maintainers: + - Nicolas Pitre <npitre@baylibre.com> + +description: | + MIPI I3C Host Controller Interface + + The MIPI I3C HCI (Host Controller Interface) specification defines + a common software driver interface to support compliant MIPI I3C + host controller hardware implementations from multiple vendors. + + The hardware is self-advertising for differences in implementation + capabilities, including the spec version it is based on, so there + isn't much to describe here (yet). + + For details, please see: + https://www.mipi.org/specifications/i3c-hci + +properties: + compatible: + const: mipi-i3c-hci + reg: + maxItems: 1 + interrupts: + maxItems: 1 + +required: + - compatible + - reg + - interrupts + +additionalProperties: false + +examples: + - | + i3c@a0000000 { + compatible = "mipi-i3c-hci"; + reg = <0xa0000000 0x2000>; + interrupts = <89>; + }; diff --git a/Documentation/devicetree/bindings/power/reset/ocelot-reset.txt b/Documentation/devicetree/bindings/power/reset/ocelot-reset.txt index 4d530d815484..c5de7b555feb 100644 --- a/Documentation/devicetree/bindings/power/reset/ocelot-reset.txt +++ b/Documentation/devicetree/bindings/power/reset/ocelot-reset.txt @@ -7,7 +7,9 @@ The reset registers are both present in the MSCC vcoreiii MIPS and microchip Sparx5 armv8 SoC's. Required Properties: - - compatible: "mscc,ocelot-chip-reset" or "microchip,sparx5-chip-reset" + + - compatible: "mscc,ocelot-chip-reset", "mscc,luton-chip-reset", + "mscc,jaguar2-chip-reset" or "microchip,sparx5-chip-reset" Example: reset@1070008 { diff --git a/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml b/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml new file mode 100644 index 000000000000..03bd1fa5a623 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/regulator-poweroff.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/power/reset/regulator-poweroff.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Force-disable power regulator to turn the power off. + +maintainers: + - Michael Klein <michael@fossekall.de> + +description: | + When the power-off handler is called, a power regulator is disabled by + calling regulator_force_disable(). If the power is still on and the + CPU still running after a 3000ms delay, a warning is emitted. + +properties: + compatible: + const: "regulator-poweroff" + + cpu-supply: + description: + regulator to disable on power-down + +required: + - compatible + - cpu-supply + +additionalProperties: false + +examples: + - | + regulator-poweroff { + compatible = "regulator-poweroff"; + cpu-supply = <®_vcc1v2>; + }; +... diff --git a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt deleted file mode 100644 index 985fcc65f8c4..000000000000 --- a/Documentation/devicetree/bindings/pwm/atmel-tcb-pwm.txt +++ /dev/null @@ -1,16 +0,0 @@ -Atmel TCB PWM controller - -Required properties: -- compatible: should be "atmel,tcb-pwm" -- #pwm-cells: should be 3. See pwm.yaml in this directory for a description of - the cells format. The only third cell flag supported by this binding is - PWM_POLARITY_INVERTED. -- tc-block: The Timer Counter block to use as a PWM chip. - -Example: - -pwm { - compatible = "atmel,tcb-pwm"; - #pwm-cells = <3>; - tc-block = <1>; -}; diff --git a/Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml b/Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml new file mode 100644 index 000000000000..ff6880a02ce6 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/intel,keembay-pwm.yaml @@ -0,0 +1,47 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 Intel Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/intel,keembay-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel Keem Bay PWM Device Tree Bindings + +maintainers: + - Vijayakannan Ayyathurai <vijayakannan.ayyathurai@intel.com> + +allOf: + - $ref: pwm.yaml# + +properties: + compatible: + enum: + - intel,keembay-pwm + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + "#pwm-cells": + const: 2 + +required: + - compatible + - reg + - clocks + - '#pwm-cells' + +additionalProperties: false + +examples: + - | + #define KEEM_BAY_A53_GPIO + + pwm@203200a0 { + compatible = "intel,keembay-pwm"; + reg = <0x203200a0 0xe8>; + clocks = <&scmi_clk KEEM_BAY_A53_GPIO>; + #pwm-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/pwm/intel,lgm-pwm.yaml b/Documentation/devicetree/bindings/pwm/intel,lgm-pwm.yaml new file mode 100644 index 000000000000..11a606536169 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/intel,lgm-pwm.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/intel,lgm-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: LGM SoC PWM fan controller + +maintainers: + - Rahul Tanwar <rtanwar@maxlinear.com> + +properties: + compatible: + const: intel,lgm-pwm + + reg: + maxItems: 1 + + "#pwm-cells": + const: 2 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - resets + +additionalProperties: false + +examples: + - | + pwm: pwm@e0d00000 { + compatible = "intel,lgm-pwm"; + reg = <0xe0d00000 0x30>; + #pwm-cells = <2>; + clocks = <&cgu0 126>; + resets = <&rcu0 0x30 21>; + }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt index 29adff59c479..25ed214473d7 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-mediatek.txt @@ -7,6 +7,7 @@ Required properties: - "mediatek,mt7623-pwm": found on mt7623 SoC. - "mediatek,mt7628-pwm": found on mt7628 SoC. - "mediatek,mt7629-pwm": found on mt7629 SoC. + - "mediatek,mt8183-pwm": found on mt8183 SoC. - "mediatek,mt8516-pwm": found on mt8516 SoC. - reg: physical base address and length of the controller's registers. - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of diff --git a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt index 0521957c253f..902b271891ae 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-mtk-disp.txt @@ -4,6 +4,7 @@ Required properties: - compatible: should be "mediatek,<name>-disp-pwm": - "mediatek,mt2701-disp-pwm": found on mt2701 SoC. - "mediatek,mt6595-disp-pwm": found on mt6595 SoC. + - "mediatek,mt8167-disp-pwm", "mediatek,mt8173-disp-pwm": found on mt8167 SoC. - "mediatek,mt8173-disp-pwm": found on mt8173 SoC. - reg: physical base address and length of the controller's registers. - #pwm-cells: must be 2. See pwm.yaml in this directory for a description of diff --git a/Documentation/devicetree/bindings/rtc/rtc.yaml b/Documentation/devicetree/bindings/rtc/rtc.yaml index 8acd2de3de3a..d30dc045aac6 100644 --- a/Documentation/devicetree/bindings/rtc/rtc.yaml +++ b/Documentation/devicetree/bindings/rtc/rtc.yaml @@ -63,6 +63,11 @@ properties: description: Enables wake up of host system on alarm. + reset-source: + $ref: /schemas/types.yaml#/definitions/flag + description: + The RTC is able to reset the machine. + additionalProperties: true ... diff --git a/Documentation/devicetree/bindings/soc/microchip/atmel,at91rm9200-tcb.yaml b/Documentation/devicetree/bindings/soc/microchip/atmel,at91rm9200-tcb.yaml index 55fffae05dcf..597d67fba92f 100644 --- a/Documentation/devicetree/bindings/soc/microchip/atmel,at91rm9200-tcb.yaml +++ b/Documentation/devicetree/bindings/soc/microchip/atmel,at91rm9200-tcb.yaml @@ -59,6 +59,7 @@ patternProperties: items: - enum: - atmel,tcb-timer + - atmel,tcb-pwm - microchip,tcb-capture reg: description: @@ -68,10 +69,35 @@ patternProperties: minItems: 1 maxItems: 3 + required: + - compatible + - reg + + "^pwm@[0-2]$": + description: The timer block channels that are used as PWMs. + $ref: ../../pwm/pwm.yaml# + type: object + properties: + compatible: + const: atmel,tcb-pwm + reg: + description: + TCB channel to use for this PWM. + enum: [ 0, 1, 2 ] + + "#pwm-cells": + description: + The only third cell flag supported by this binding is + PWM_POLARITY_INVERTED. + const: 3 required: - compatible - reg + - "#pwm-cells" + + additionalProperties: false + allOf: - if: @@ -158,7 +184,13 @@ examples: compatible = "atmel,tcb-timer"; reg = <1>; }; - }; + + pwm@2 { + compatible = "atmel,tcb-pwm"; + reg = <2>; + #pwm-cells = <3>; + }; + }; /* TCB0 Capture with QDEC: */ timer@f800c000 { compatible = "atmel,at91rm9200-tcb", "simple-mfd", "syscon"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index ffaf833b97ee..041ae90b0d8f 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -187,6 +187,8 @@ patternProperties: description: CALAO Systems SAS "^calxeda,.*": description: Calxeda + "^canaan,.*": + description: Canaan, Inc. "^caninos,.*": description: Caninos Loucos Program "^capella,.*": diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml index e8f226376108..5ac607de8be4 100644 --- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml +++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml @@ -22,6 +22,9 @@ properties: - const: allwinner,sun50i-a64-wdt - const: allwinner,sun6i-a31-wdt - items: + - const: allwinner,sun50i-a100-wdt + - const: allwinner,sun6i-a31-wdt + - items: - const: allwinner,sun50i-h6-wdt - const: allwinner,sun6i-a31-wdt - items: diff --git a/Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml b/Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml index d9fc7bb851b1..f7ee9229c29f 100644 --- a/Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml +++ b/Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml @@ -14,7 +14,15 @@ maintainers: properties: compatible: - const: snps,dw-wdt + oneOf: + - const: snps,dw-wdt + - items: + - enum: + - rockchip,rk3066-wdt + - rockchip,rk3188-wdt + - rockchip,rk3288-wdt + - rockchip,rk3368-wdt + - const: snps,dw-wdt reg: maxItems: 1 |