diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
32 files changed, 1243 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt b/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt new file mode 100644 index 000000000000..31af1cbb60bd --- /dev/null +++ b/Documentation/devicetree/bindings/arm/mrvl/tauros2.txt @@ -0,0 +1,17 @@ +* Marvell Tauros2 Cache + +Required properties: +- compatible : Should be "marvell,tauros2-cache". +- marvell,tauros2-cache-features : Specify the features supported for the + tauros2 cache. + The features including + CACHE_TAUROS2_PREFETCH_ON (1 << 0) + CACHE_TAUROS2_LINEFILL_BURST8 (1 << 1) + The definition can be found at + arch/arm/include/asm/hardware/cache-tauros2.h + +Example: + L2: l2-cache { + compatible = "marvell,tauros2-cache"; + marvell,tauros2-cache-features = <0x3>; + }; diff --git a/Documentation/devicetree/bindings/arm/msm/timer.txt b/Documentation/devicetree/bindings/arm/msm/timer.txt new file mode 100644 index 000000000000..8c5907b9cae8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/msm/timer.txt @@ -0,0 +1,38 @@ +* MSM Timer + +Properties: + +- compatible : Should at least contain "qcom,msm-timer". More specific + properties such as "qcom,msm-gpt" and "qcom,msm-dgt" specify a general + purpose timer and a debug timer respectively. + +- interrupts : Interrupt indicating a match event. + +- reg : Specifies the base address of the timer registers. The second region + specifies an optional register used to configure the clock divider. + +- clock-frequency : The frequency of the timer in Hz. + +Optional: + +- cpu-offset : per-cpu offset used when the timer is accessed without the + CPU remapping facilities. The offset is cpu-offset * cpu-nr. + +Example: + + timer@200a004 { + compatible = "qcom,msm-gpt", "qcom,msm-timer"; + interrupts = <1 2 0x301>; + reg = <0x0200a004 0x10>; + clock-frequency = <32768>; + cpu-offset = <0x40000>; + }; + + timer@200a024 { + compatible = "qcom,msm-dgt", "qcom,msm-timer"; + interrupts = <1 3 0x301>; + reg = <0x0200a024 0x10>, + <0x0200a034 0x4>; + clock-frequency = <6750000>; + cpu-offset = <0x40000>; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index ccdd0e53451f..d0051a750587 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -36,6 +36,9 @@ Boards: - OMAP3 BeagleBoard : Low cost community board compatible = "ti,omap3-beagle", "ti,omap3" +- OMAP3 Tobi with Overo : Commercial expansion board with daughter board + compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3" + - OMAP4 SDP : Software Developement Board compatible = "ti,omap4-sdp", "ti,omap4430" diff --git a/Documentation/devicetree/bindings/arm/vt8500.txt b/Documentation/devicetree/bindings/arm/vt8500.txt new file mode 100644 index 000000000000..d657832c6819 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500.txt @@ -0,0 +1,14 @@ +VIA/Wondermedia VT8500 Platforms Device Tree Bindings +--------------------------------------- + +Boards with the VIA VT8500 SoC shall have the following properties: +Required root node property: +compatible = "via,vt8500"; + +Boards with the Wondermedia WM8505 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8505"; + +Boards with the Wondermedia WM8650 SoC shall have the following properties: +Required root node property: +compatible = "wm,wm8650"; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt new file mode 100644 index 000000000000..0a4ce1051b02 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-intc.txt @@ -0,0 +1,16 @@ +VIA/Wondermedia VT8500 Interrupt Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-intc" +- reg : Should contain 1 register ranges(address and length) +- #interrupt-cells : should be <1> + +Example: + + intc: interrupt-controller@d8140000 { + compatible = "via,vt8500-intc"; + interrupt-controller; + reg = <0xd8140000 0x10000>; + #interrupt-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt new file mode 100644 index 000000000000..521b9c7de933 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-pmc.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia VT8500 Power Management Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-pmc" +- reg : Should contain 1 register ranges(address and length) + +Example: + + pmc@d8130000 { + compatible = "via,vt8500-pmc"; + reg = <0xd8130000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt new file mode 100644 index 000000000000..901c73f0d8ef --- /dev/null +++ b/Documentation/devicetree/bindings/arm/vt8500/via,vt8500-timer.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Timer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-timer" +- reg : Should contain 1 register ranges(address and length) +- interrupts : interrupt for the timer + +Example: + + timer@d8130100 { + compatible = "via,vt8500-timer"; + reg = <0xd8130100 0x28>; + interrupts = <36>; + }; diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt new file mode 100644 index 000000000000..a0b867ef8d96 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -0,0 +1,76 @@ +* Clock bindings for Freescale i.MX23 + +Required properties: +- compatible: Should be "fsl,imx23-clkctrl" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX23 +clocks and IDs. + + Clock ID + ------------------ + ref_xtal 0 + pll 1 + ref_cpu 2 + ref_emi 3 + ref_pix 4 + ref_io 5 + saif_sel 6 + lcdif_sel 7 + gpmi_sel 8 + ssp_sel 9 + emi_sel 10 + cpu 11 + etm_sel 12 + cpu_pll 13 + cpu_xtal 14 + hbus 15 + xbus 16 + lcdif_div 17 + ssp_div 18 + gpmi_div 19 + emi_pll 20 + emi_xtal 21 + etm_div 22 + saif_div 23 + clk32k_div 24 + rtc 25 + adc 26 + spdif_div 27 + clk32k 28 + dri 29 + pwm 30 + filt 31 + uart 32 + ssp 33 + gpmi 34 + spdif 35 + emi 36 + saif 37 + lcdif 38 + etm 39 + usb 40 + usb_pwr 41 + +Examples: + +clks: clkctrl@80040000 { + compatible = "fsl,imx23-clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; + clock-output-names = + ... + "uart", /* 32 */ + ... + "end_of_list"; +}; + +auart0: serial@8006c000 { + compatible = "fsl,imx23-auart"; + reg = <0x8006c000 0x2000>; + interrupts = <24 25 23>; + clocks = <&clks 32>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt new file mode 100644 index 000000000000..aa2af2866fe8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -0,0 +1,99 @@ +* Clock bindings for Freescale i.MX28 + +Required properties: +- compatible: Should be "fsl,imx28-clkctrl" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX28 +clocks and IDs. + + Clock ID + ------------------ + ref_xtal 0 + pll0 1 + pll1 2 + pll2 3 + ref_cpu 4 + ref_emi 5 + ref_io0 6 + ref_io1 7 + ref_pix 8 + ref_hsadc 9 + ref_gpmi 10 + saif0_sel 11 + saif1_sel 12 + gpmi_sel 13 + ssp0_sel 14 + ssp1_sel 15 + ssp2_sel 16 + ssp3_sel 17 + emi_sel 18 + etm_sel 19 + lcdif_sel 20 + cpu 21 + ptp_sel 22 + cpu_pll 23 + cpu_xtal 24 + hbus 25 + xbus 26 + ssp0_div 27 + ssp1_div 28 + ssp2_div 29 + ssp3_div 30 + gpmi_div 31 + emi_pll 32 + emi_xtal 33 + lcdif_div 34 + etm_div 35 + ptp 36 + saif0_div 37 + saif1_div 38 + clk32k_div 39 + rtc 40 + lradc 41 + spdif_div 42 + clk32k 43 + pwm 44 + uart 45 + ssp0 46 + ssp1 47 + ssp2 48 + ssp3 49 + gpmi 50 + spdif 51 + emi 52 + saif0 53 + saif1 54 + lcdif 55 + etm 56 + fec 57 + can0 58 + can1 59 + usb0 60 + usb1 61 + usb0_pwr 62 + usb1_pwr 63 + enet_out 64 + +Examples: + +clks: clkctrl@80040000 { + compatible = "fsl,imx28-clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; + clock-output-names = + ... + "uart", /* 45 */ + ... + "end_of_list"; +}; + +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112 70 71>; + clocks = <&clks 45>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt new file mode 100644 index 000000000000..492bd991d52a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -0,0 +1,222 @@ +* Clock bindings for Freescale i.MX6 Quad + +Required properties: +- compatible: Should be "fsl,imx6q-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX6Q +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + ckil 1 + ckih 2 + osc 3 + pll2_pfd0_352m 4 + pll2_pfd1_594m 5 + pll2_pfd2_396m 6 + pll3_pfd0_720m 7 + pll3_pfd1_540m 8 + pll3_pfd2_508m 9 + pll3_pfd3_454m 10 + pll2_198m 11 + pll3_120m 12 + pll3_80m 13 + pll3_60m 14 + twd 15 + step 16 + pll1_sw 17 + periph_pre 18 + periph2_pre 19 + periph_clk2_sel 20 + periph2_clk2_sel 21 + axi_sel 22 + esai_sel 23 + asrc_sel 24 + spdif_sel 25 + gpu2d_axi 26 + gpu3d_axi 27 + gpu2d_core_sel 28 + gpu3d_core_sel 29 + gpu3d_shader_sel 30 + ipu1_sel 31 + ipu2_sel 32 + ldb_di0_sel 33 + ldb_di1_sel 34 + ipu1_di0_pre_sel 35 + ipu1_di1_pre_sel 36 + ipu2_di0_pre_sel 37 + ipu2_di1_pre_sel 38 + ipu1_di0_sel 39 + ipu1_di1_sel 40 + ipu2_di0_sel 41 + ipu2_di1_sel 42 + hsi_tx_sel 43 + pcie_axi_sel 44 + ssi1_sel 45 + ssi2_sel 46 + ssi3_sel 47 + usdhc1_sel 48 + usdhc2_sel 49 + usdhc3_sel 50 + usdhc4_sel 51 + enfc_sel 52 + emi_sel 53 + emi_slow_sel 54 + vdo_axi_sel 55 + vpu_axi_sel 56 + cko1_sel 57 + periph 58 + periph2 59 + periph_clk2 60 + periph2_clk2 61 + ipg 62 + ipg_per 63 + esai_pred 64 + esai_podf 65 + asrc_pred 66 + asrc_podf 67 + spdif_pred 68 + spdif_podf 69 + can_root 70 + ecspi_root 71 + gpu2d_core_podf 72 + gpu3d_core_podf 73 + gpu3d_shader 74 + ipu1_podf 75 + ipu2_podf 76 + ldb_di0_podf 77 + ldb_di1_podf 78 + ipu1_di0_pre 79 + ipu1_di1_pre 80 + ipu2_di0_pre 81 + ipu2_di1_pre 82 + hsi_tx_podf 83 + ssi1_pred 84 + ssi1_podf 85 + ssi2_pred 86 + ssi2_podf 87 + ssi3_pred 88 + ssi3_podf 89 + uart_serial_podf 90 + usdhc1_podf 91 + usdhc2_podf 92 + usdhc3_podf 93 + usdhc4_podf 94 + enfc_pred 95 + enfc_podf 96 + emi_podf 97 + emi_slow_podf 98 + vpu_axi_podf 99 + cko1_podf 100 + axi 101 + mmdc_ch0_axi_podf 102 + mmdc_ch1_axi_podf 103 + arm 104 + ahb 105 + apbh_dma 106 + asrc 107 + can1_ipg 108 + can1_serial 109 + can2_ipg 110 + can2_serial 111 + ecspi1 112 + ecspi2 113 + ecspi3 114 + ecspi4 115 + ecspi5 116 + enet 117 + esai 118 + gpt_ipg 119 + gpt_ipg_per 120 + gpu2d_core 121 + gpu3d_core 122 + hdmi_iahb 123 + hdmi_isfr 124 + i2c1 125 + i2c2 126 + i2c3 127 + iim 128 + enfc 129 + ipu1 130 + ipu1_di0 131 + ipu1_di1 132 + ipu2 133 + ipu2_di0 134 + ldb_di0 135 + ldb_di1 136 + ipu2_di1 137 + hsi_tx 138 + mlb 139 + mmdc_ch0_axi 140 + mmdc_ch1_axi 141 + ocram 142 + openvg_axi 143 + pcie_axi 144 + pwm1 145 + pwm2 146 + pwm3 147 + pwm4 148 + per1_bch 149 + gpmi_bch_apb 150 + gpmi_bch 151 + gpmi_io 152 + gpmi_apb 153 + sata 154 + sdma 155 + spba 156 + ssi1 157 + ssi2 158 + ssi3 159 + uart_ipg 160 + uart_serial 161 + usboh3 162 + usdhc1 163 + usdhc2 164 + usdhc3 165 + usdhc4 166 + vdo_axi 167 + vpu_axi 168 + cko1 169 + pll1_sys 170 + pll2_bus 171 + pll3_usb_otg 172 + pll4_audio 173 + pll5_video 174 + pll6_mlb 175 + pll7_usb_host 176 + pll8_enet 177 + ssi1_ipg 178 + ssi2_ipg 179 + ssi3_ipg 180 + rom 181 + usbphy1 182 + usbphy2 183 + ldb_di0_div_3_5 184 + ldb_di1_div_3_5 185 + +Examples: + +clks: ccm@020c4000 { + compatible = "fsl,imx6q-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <0 87 0x04 0 88 0x04>; + #clock-cells = <1>; + clock-output-names = ... + "uart_ipg", + "uart_serial", + ...; +}; + +uart1: serial@02020000 { + compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <0 26 0x04>; + clocks = <&clks 160>, <&clks 161>; + clock-names = "ipg", "per"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/clock/vt8500.txt b/Documentation/devicetree/bindings/clock/vt8500.txt new file mode 100644 index 000000000000..a880c70d0047 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/vt8500.txt @@ -0,0 +1,72 @@ +Device Tree Clock bindings for arch-vt8500 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "via,vt8500-pll-clock" - for a VT8500/WM8505 PLL clock + "wm,wm8650-pll-clock" - for a WM8650 PLL clock + "via,vt8500-device-clock" - for a VT/WM device clock + +Required properties for PLL clocks: +- reg : shall be the control register offset from PMC base for the pll clock. +- clocks : shall be the input parent clock phandle for the clock. This should + be the reference clock. +- #clock-cells : from common clock binding; shall be set to 0. + +Required properties for device clocks: +- clocks : shall be the input parent clock phandle for the clock. This should + be a pll output. +- #clock-cells : from common clock binding; shall be set to 0. + + +Device Clocks + +Device clocks are required to have one or both of the following sets of +properties: + + +Gated device clocks: + +Required properties: +- enable-reg : shall be the register offset from PMC base for the enable + register. +- enable-bit : shall be the bit within enable-reg to enable/disable the clock. + + +Divisor device clocks: + +Required property: +- divisor-reg : shall be the register offset from PMC base for the divisor + register. +Optional property: +- divisor-mask : shall be the mask for the divisor register. Defaults to 0x1f + if not specified. + + +For example: + +ref25: ref25M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; +}; + +plla: plla { + #clock-cells = <0>; + compatible = "wm,wm8650-pll-clock"; + clocks = <&ref25>; + reg = <0x200>; +}; + +sdhc: sdhc { + #clock-cells = <0>; + compatible = "via,vt8500-device-clock"; + clocks = <&pllb>; + divisor-reg = <0x328>; + divisor-mask = <0x3f>; + enable-reg = <0x254>; + enable-bit = <18>; +}; diff --git a/Documentation/devicetree/bindings/dma/mmp-dma.txt b/Documentation/devicetree/bindings/dma/mmp-dma.txt new file mode 100644 index 000000000000..a4fa4efa1d83 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/mmp-dma.txt @@ -0,0 +1,74 @@ +* MARVELL MMP DMA controller + +Marvell Peripheral DMA Controller +Used platfroms: pxa688, pxa910, pxa3xx, etc + +Required properties: +- compatible: Should be "marvell,pdma-1.0" +- reg: Should contain DMA registers location and length. +- interrupts: Either contain all of the per-channel DMA interrupts + or one irq for pdma device +- #dma-channels: Number of DMA channels supported by the controller. + +"marvell,pdma-1.0" +Used platfroms: pxa25x, pxa27x, pxa3xx, pxa93x, pxa168, pxa910, pxa688. + +Examples: + +/* + * Each channel has specific irq + * ICU parse out irq channel from ICU register, + * while DMA controller may not able to distinguish the irq channel + * Using this method, interrupt-parent is required as demuxer + * For example, pxa688 icu register 0x128, bit 0~15 is PDMA channel irq, + * 18~21 is ADMA irq + */ +pdma: dma-controller@d4000000 { + compatible = "marvell,pdma-1.0"; + reg = <0xd4000000 0x10000>; + interrupts = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15>; + interrupt-parent = <&intcmux32>; + #dma-channels = <16>; + }; + +/* + * One irq for all channels + * Dmaengine driver (DMA controller) distinguish irq channel via + * parsing internal register + */ +pdma: dma-controller@d4000000 { + compatible = "marvell,pdma-1.0"; + reg = <0xd4000000 0x10000>; + interrupts = <47>; + #dma-channels = <16>; + }; + + +Marvell Two Channel DMA Controller used specifically for audio +Used platfroms: pxa688, pxa910 + +Required properties: +- compatible: Should be "marvell,adma-1.0" or "marvell,pxa910-squ" +- reg: Should contain DMA registers location and length. +- interrupts: Either contain all of the per-channel DMA interrupts + or one irq for dma device + +"marvell,adma-1.0" used on pxa688 +"marvell,pxa910-squ" used on pxa910 + +Examples: + +/* each channel has specific irq */ +adma0: dma-controller@d42a0800 { + compatible = "marvell,adma-1.0"; + reg = <0xd42a0800 0x100>; + interrupts = <18 19>; + interrupt-parent = <&intcmux32>; + }; + +/* One irq for all channels */ +squ: dma-controller@d42a0800 { + compatible = "marvell,pxa910-squ"; + reg = <0xd42a0800 0x100>; + interrupts = <46>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt index 5375625e8cd2..f1e5dfecf55d 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-samsung.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-samsung.txt @@ -39,3 +39,46 @@ Example: #gpio-cells = <4>; gpio-controller; }; + + +Samsung S3C24XX GPIO Controller + +Required properties: +- compatible: Compatible property value should be "samsung,s3c24xx-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #gpio-cells: Should be 3. The syntax of the gpio specifier used by client nodes + should be the following with values derived from the SoC user manual. + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [mux function] + [flags and pull up/down] + + Values for gpio specifier: + - Pin number: depending on the controller a number from 0 up to 15. + - Mux function: Depending on the SoC and the gpio bank the gpio can be set + as input, output or a special function + - Flags and Pull Up/Down: the values to use differ for the individual SoCs + example S3C2416/S3C2450: + 0 - Pull Up/Down Disabled. + 1 - Pull Down Enabled. + 2 - Pull Up Enabled. + Bit 16 (0x00010000) - Input is active low. + Consult the user manual for the correct values of Mux and Pull Up/Down. + +- gpio-controller: Specifies that the node is a gpio controller. +- #address-cells: should be 1. +- #size-cells: should be 1. + +Example: + + gpa: gpio-controller@56000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "samsung,s3c24xx-gpio"; + reg = <0x56000000 0x10>; + #gpio-cells = <3>; + gpio-controller; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt index 16695d9cf1e8..66788fda1db3 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt @@ -11,6 +11,11 @@ Required properties: - interrupt-controller: Mark the device node as an interrupt controller The first cell is the GPIO number. The second cell is not used. +- ti,use-leds : Enables LEDA and LEDB outputs if set +- ti,debounce : if n-th bit is set, debounces GPIO-n +- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1) +- ti,pullups : if n-th bit is set, set a pullup on GPIO-n +- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n Example: @@ -20,4 +25,5 @@ twl_gpio: gpio { gpio-controller; #interrupt-cells = <2>; interrupt-controller; + ti,use-leds; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt new file mode 100644 index 000000000000..f4dc5233167e --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-vt8500.txt @@ -0,0 +1,24 @@ +VIA/Wondermedia VT8500 GPIO Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-gpio", "wm,wm8505-gpio" + or "wm,wm8650-gpio" depending on your SoC +- reg : Should contain 1 register range (address and length) +- #gpio-cells : should be <3>. + 1) bank + 2) pin number + 3) flags - should be 0 + +Example: + + gpio: gpio-controller@d8110000 { + compatible = "via,vt8500-gpio"; + gpio-controller; + reg = <0xd8110000 0x10000>; + #gpio-cells = <3>; + }; + + vibrate { + gpios = <&gpio 0 1 0>; /* Bank 0, Pin 1, No flags */ + }; diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index 1a85f986961b..2f5322b119eb 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -56,3 +56,4 @@ stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS ti,tsc2003 I2C Touch-Screen Controller +ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface diff --git a/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt b/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt new file mode 100644 index 000000000000..9ceb19e0c7fd --- /dev/null +++ b/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt @@ -0,0 +1,52 @@ +* AC timing parameters of LPDDR2(JESD209-2) memories for a given speed-bin + +Required properties: +- compatible : Should be "jedec,lpddr2-timings" +- min-freq : minimum DDR clock frequency for the speed-bin. Type is <u32> +- max-freq : maximum DDR clock frequency for the speed-bin. Type is <u32> + +Optional properties: + +The following properties represent AC timing parameters from the memory +data-sheet of the device for a given speed-bin. All these properties are +of type <u32> and the default unit is ps (pico seconds). Parameters with +a different unit have a suffix indicating the unit such as 'tRAS-max-ns' +- tRCD +- tWR +- tRAS-min +- tRRD +- tWTR +- tXP +- tRTP +- tDQSCK-max +- tFAW +- tZQCS +- tZQinit +- tRPab +- tZQCL +- tCKESR +- tRAS-max-ns +- tDQSCK-max-derated + +Example: + +timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <400000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <7500>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; +}; diff --git a/Documentation/devicetree/bindings/lpddr2/lpddr2.txt b/Documentation/devicetree/bindings/lpddr2/lpddr2.txt new file mode 100644 index 000000000000..58354a075e13 --- /dev/null +++ b/Documentation/devicetree/bindings/lpddr2/lpddr2.txt @@ -0,0 +1,102 @@ +* LPDDR2 SDRAM memories compliant to JEDEC JESD209-2 + +Required properties: +- compatible : Should be one of - "jedec,lpddr2-nvm", "jedec,lpddr2-s2", + "jedec,lpddr2-s4" + + "ti,jedec-lpddr2-s2" should be listed if the memory part is LPDDR2-S2 type + + "ti,jedec-lpddr2-s4" should be listed if the memory part is LPDDR2-S4 type + + "ti,jedec-lpddr2-nvm" should be listed if the memory part is LPDDR2-NVM type + +- density : <u32> representing density in Mb (Mega bits) + +- io-width : <u32> representing bus width. Possible values are 8, 16, and 32 + +Optional properties: + +The following optional properties represent the minimum value of some AC +timing parameters of the DDR device in terms of number of clock cycles. +These values shall be obtained from the device data-sheet. +- tRRD-min-tck +- tWTR-min-tck +- tXP-min-tck +- tRTP-min-tck +- tCKE-min-tck +- tRPab-min-tck +- tRCD-min-tck +- tWR-min-tck +- tRASmin-min-tck +- tCKESR-min-tck +- tFAW-min-tck + +Child nodes: +- The lpddr2 node may have one or more child nodes of type "lpddr2-timings". + "lpddr2-timings" provides AC timing parameters of the device for + a given speed-bin. The user may provide the timings for as many + speed-bins as is required. Please see Documentation/devicetree/ + bindings/lpddr2/lpddr2-timings.txt for more information on "lpddr2-timings" + +Example: + +elpida_ECB240ABACN : lpddr2 { + compatible = "Elpida,ECB240ABACN","jedec,lpddr2-s4"; + density = <2048>; + io-width = <32>; + + tRPab-min-tck = <3>; + tRCD-min-tck = <3>; + tWR-min-tck = <3>; + tRASmin-min-tck = <3>; + tRRD-min-tck = <2>; + tWTR-min-tck = <2>; + tXP-min-tck = <2>; + tRTP-min-tck = <2>; + tCKE-min-tck = <3>; + tCKESR-min-tck = <3>; + tFAW-min-tck = <8>; + + timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <400000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <7500>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; + }; + + timings_elpida_ECB240ABACN_200mhz: lpddr2-timings@1 { + compatible = "jedec,lpddr2-timings"; + min-freq = <10000000>; + max-freq = <200000000>; + tRPab = <21000>; + tRCD = <18000>; + tWR = <15000>; + tRAS-min = <42000>; + tRRD = <10000>; + tWTR = <10000>; + tXP = <7500>; + tRTP = <7500>; + tCKESR = <15000>; + tDQSCK-max = <5500>; + tFAW = <50000>; + tZQCS = <90000>; + tZQCL = <360000>; + tZQinit = <1000000>; + tRAS-max-ns = <70000>; + }; + +} diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt new file mode 100644 index 000000000000..938f8e1ba205 --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt @@ -0,0 +1,55 @@ +* EMIF family of TI SDRAM controllers + +EMIF - External Memory Interface - is an SDRAM controller used in +TI SoCs. EMIF supports, based on the IP revision, one or more of +DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance +of the EMIF IP and memory parts attached to it. + +Required properties: +- compatible : Should be of the form "ti,emif-<ip-rev>" where <ip-rev> + is the IP revision of the specific EMIF instance. + +- phy-type : <u32> indicating the DDR phy type. Following are the + allowed values + <1> : Attila PHY + <2> : Intelli PHY + +- device-handle : phandle to a "lpddr2" node representing the memory part + +- ti,hwmods : For TI hwmods processing and omap device creation + the value shall be "emif<n>" where <n> is the number of the EMIF + instance with base 1. + +Optional properties: +- cs1-used : Have this property if CS1 of this EMIF + instance has a memory part attached to it. If there is a memory + part attached to CS1, it should be the same type as the one on CS0, + so there is no need to give the details of this memory part. + +- cal-resistor-per-cs : Have this property if the board has one + calibration resistor per chip-select. + +- hw-caps-read-idle-ctrl: Have this property if the controller + supports read idle window programming + +- hw-caps-dll-calib-ctrl: Have this property if the controller + supports dll calibration control + +- hw-caps-ll-interface : Have this property if the controller + has a low latency interface and corresponding interrupt events + +- hw-caps-temp-alert : Have this property if the controller + has capability for generating SDRAM temperature alerts + +Example: + +emif1: emif@0x4c000000 { + compatible = "ti,emif-4d"; + ti,hwmods = "emif2"; + phy-type = <1>; + device-handle = <&elpida_ECB240ABACN>; + cs1-used; + hw-caps-read-idle-ctrl; + hw-caps-ll-interface; + hw-caps-temp-alert; +}; diff --git a/Documentation/devicetree/bindings/mfd/ab8500.txt b/Documentation/devicetree/bindings/mfd/ab8500.txt index 69e757a657a0..ce83c8d3c00e 100644 --- a/Documentation/devicetree/bindings/mfd/ab8500.txt +++ b/Documentation/devicetree/bindings/mfd/ab8500.txt @@ -23,6 +23,7 @@ Device IRQ Names Supply Names Description ab8500-bm : : : Battery Manager ab8500-btemp : : : Battery Temperature ab8500-charger : : : Battery Charger +ab8500-codec : : : Audio Codec ab8500-fg : : : Fuel Gauge ab8500-gpadc : HW_CONV_END : vddadc : Analogue to Digital Converter SW_CONV_END : : @@ -52,6 +53,14 @@ Optional child device properties: supplied in the interrupts property - <supply_name>-supply : contains a phandle to the regulator supply node in Device Tree +Non-standard child device properties: + - Audio CODEC: + - stericsson,amic[1|2]-type-single-ended : Single-ended Analoge Mic (default: differential) + - stericsson,amic1a-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic1b-bias-vamic2 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,amic2-bias-vamic1 : Analoge Mic wishes to use a non-standard Vamic + - stericsson,earpeice-cmv : Earpeice voltage (only: 950 | 1100 | 1270 | 1580) + ab8500@5 { compatible = "stericsson,ab8500"; reg = <5>; /* mailbox 5 is i2c */ @@ -110,6 +119,12 @@ ab8500@5 { compatible = "stericsson,ab8500-pwm"; }; + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; + ab8500-regulators { compatible = "stericsson,ab8500-regulator"; diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt new file mode 100644 index 000000000000..f1421e2bbab7 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt @@ -0,0 +1,31 @@ +PXA3xx NAND DT bindings + +Required properties: + + - compatible: Should be "marvell,pxa3xx-nand" + - reg: The register base for the controller + - interrupts: The interrupt to map + - #address-cells: Set to <1> if the node includes partitions + +Optional properties: + + - marvell,nand-enable-arbiter: Set to enable the bus arbiter + - marvell,nand-keep-config: Set to keep the NAND controller config as set + by the bootloader + - num-cs: Number of chipselect lines to usw + +Example: + + nand0: nand@43100000 { + compatible = "marvell,pxa3xx-nand"; + reg = <0x43100000 90>; + interrupts = <45>; + #address-cells = <1>; + + marvell,nand-enable-arbiter; + marvell,nand-keep-config; + num-cs = <1>; + + /* partitions (optional) */ + }; + diff --git a/Documentation/devicetree/bindings/rtc/pxa-rtc.txt b/Documentation/devicetree/bindings/rtc/pxa-rtc.txt new file mode 100644 index 000000000000..8c6672a1b7d7 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/pxa-rtc.txt @@ -0,0 +1,14 @@ +* PXA RTC + +PXA specific RTC driver. + +Required properties: +- compatible : Should be "marvell,pxa-rtc" + +Examples: + +rtc@40900000 { + compatible = "marvell,pxa-rtc"; + reg = <0x40900000 0x3c>; + interrupts = <30 31>; +}; diff --git a/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt b/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt new file mode 100644 index 000000000000..3c0484c49582 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/via,vt8500-rtc.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 Realtime Clock Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-rtc" +- reg : Should contain 1 register ranges(address and length) +- interrupts : alarm interrupt + +Example: + + rtc@d8100000 { + compatible = "via,vt8500-rtc"; + reg = <0xd8100000 0x10000>; + interrupts = <48>; + }; diff --git a/Documentation/devicetree/bindings/sound/ux500-mop500.txt b/Documentation/devicetree/bindings/sound/ux500-mop500.txt new file mode 100644 index 000000000000..48e071c96b46 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ux500-mop500.txt @@ -0,0 +1,39 @@ +* MOP500 Audio Machine Driver + +This node is responsible for linking together all ux500 Audio Driver components. + +Required properties: + - compatible : "stericsson,snd-soc-mop500" + +Non-standard properties: + - stericsson,cpu-dai : Phandle to the CPU-side DAI + - stericsson,audio-codec : Phandle to the Audio CODEC + - stericsson,card-name : Over-ride default card name + +Example: + + sound { + compatible = "stericsson,snd-soc-mop500"; + + stericsson,cpu-dai = <&msp1 &msp3>; + stericsson,audio-codec = <&codec>; + }; + + msp1: msp@80124000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80124000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + msp3: msp@80125000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80125000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; diff --git a/Documentation/devicetree/bindings/sound/ux500-msp.txt b/Documentation/devicetree/bindings/sound/ux500-msp.txt new file mode 100644 index 000000000000..99acd9c774e1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ux500-msp.txt @@ -0,0 +1,43 @@ +* ux500 MSP (CPU-side Digital Audio Interface) + +Required properties: + - compatible :"stericsson,ux500-msp-i2s" + - reg : Physical base address and length of the device's registers. + +Optional properties: + - interrupts : The interrupt output from the device. + - interrupt-parent : The parent interrupt controller. + - <name>-supply : Phandle to the regulator <name> supply + +Example: + + sound { + compatible = "stericsson,snd-soc-mop500"; + + stericsson,platform-pcm-dma = <&pcm>; + stericsson,cpu-dai = <&msp1 &msp3>; + stericsson,audio-codec = <&codec>; + }; + + pcm: ux500-pcm { + compatible = "stericsson,ux500-pcm"; + }; + + msp1: msp@80124000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80124000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + msp3: msp@80125000 { + compatible = "stericsson,ux500-msp-i2s"; + reg = <0x80125000 0x1000>; + interrupts = <0 62 0x4>; + v-ape-supply = <&db8500_vape_reg>; + }; + + codec: ab8500-codec { + compatible = "stericsson,ab8500-codec"; + stericsson,earpeice-cmv = <950>; /* Units in mV. */ + }; diff --git a/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt new file mode 100644 index 000000000000..5feef1ef167d --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/via,vt8500-uart.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500 UART Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-uart" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UART interrupt +- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock) + +Example: + + uart@d8210000 { + compatible = "via,vt8500-uart"; + reg = <0xd8210000 0x1040>; + interrupts = <47>; + clocks = <&ref24>; + }; diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/platform-uhci.txt index 91477d6830ec..a4fb0719d157 100644 --- a/Documentation/devicetree/bindings/usb/platform-uhci.txt +++ b/Documentation/devicetree/bindings/usb/platform-uhci.txt @@ -1,12 +1,15 @@ -Generic Platform UHCI controllers. +Generic Platform UHCI Controller +----------------------------------------------------- Required properties: - - compatible: Should be "platform-uhci". - - reg: Address range of the uhci registers - - interrupts: Should contain the uhci interrupt. +- compatible : "platform-uhci" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UHCI controller interrupt -usb: uhci@D8007301 { - compatible = "platform-uhci", "usb-uhci"; - reg = <0xD8007301 0x200>; - interrupts = <0>; -}; +Example: + + uhci@d8007b00 { + compatible = "platform-uhci"; + reg = <0xd8007b00 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt new file mode 100644 index 000000000000..17b3ad1d97e7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/via,vt8500-ehci.txt @@ -0,0 +1,15 @@ +VIA/Wondermedia VT8500 EHCI Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-ehci" +- reg : Should contain 1 register ranges(address and length) +- interrupts : ehci controller interrupt + +Example: + + ehci@d8007900 { + compatible = "via,vt8500-ehci"; + reg = <0xd8007900 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4f293e5571f0..9de2b9ff9d6e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -48,5 +48,7 @@ sirf SiRF Technology, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments +via VIA Technologies, Inc. wlf Wolfson Microelectronics +wm Wondermedia Technologies, Inc. xlnx Xilinx diff --git a/Documentation/devicetree/bindings/video/via,vt8500-fb.txt b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt new file mode 100644 index 000000000000..c870b6478ec8 --- /dev/null +++ b/Documentation/devicetree/bindings/video/via,vt8500-fb.txt @@ -0,0 +1,62 @@ +VIA VT8500 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-fb" +- reg : Should contain 1 register ranges(address and length) +- interrupts : framebuffer controller interrupt +- display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. +- default-mode: a videomode within the display with timing parameters + as specified below. + +Example: + + fb@d800e400 { + compatible = "via,vt8500-fb"; + reg = <0xd800e400 0x400>; + interrupts = <12>; + display = <&display>; + default-mode = <&mode0>; + }; + +VIA VT8500 Display +----------------------------------------------------- +Required properties (as per of_videomode_helper): + + - hactive, vactive: Display resolution + - hfront-porch, hback-porch, hsync-len: Horizontal Display timing parameters + in pixels + vfront-porch, vback-porch, vsync-len: Vertical display timing parameters in + lines + - clock: displayclock in Hz + - bpp: lcd panel bit-depth. + <16> for RGB565, <32> for RGB888 + +Optional properties (as per of_videomode_helper): + - width-mm, height-mm: Display dimensions in mm + - hsync-active-high (bool): Hsync pulse is active high + - vsync-active-high (bool): Vsync pulse is active high + - interlaced (bool): This is an interlaced mode + - doublescan (bool): This is a doublescan mode + +Example: + display: display@0 { + modes { + mode0: mode@0 { + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hfront-porch = <40>; + hsync-len = <0>; + vback-porch = <32>; + vfront-porch = <11>; + vsync-len = <1>; + clock = <0>; /* unused but required */ + bpp = <16>; /* non-standard but required */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt b/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt new file mode 100644 index 000000000000..a850fa011f02 --- /dev/null +++ b/Documentation/devicetree/bindings/video/wm,prizm-ge-rops.txt @@ -0,0 +1,13 @@ +VIA/Wondermedia Graphics Engine Controller +----------------------------------------------------- + +Required properties: +- compatible : "wm,prizm-ge-rops" +- reg : Should contain 1 register ranges(address and length) + +Example: + + ge_rops@d8050400 { + compatible = "wm,prizm-ge-rops"; + reg = <0xd8050400 0x100>; + }; diff --git a/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt new file mode 100644 index 000000000000..3d325e1d11ee --- /dev/null +++ b/Documentation/devicetree/bindings/video/wm,wm8505-fb.txt @@ -0,0 +1,23 @@ +Wondermedia WM8505 Framebuffer +----------------------------------------------------- + +Required properties: +- compatible : "wm,wm8505-fb" +- reg : Should contain 1 register ranges(address and length) +- via,display: a phandle pointing to the display node + +Required nodes: +- display: a display node is required to initialize the lcd panel + This should be in the board dts. See definition in + Documentation/devicetree/bindings/video/via,vt8500-fb.txt +- default-mode: a videomode node as specified in + Documentation/devicetree/bindings/video/via,vt8500-fb.txt + +Example: + + fb@d8050800 { + compatible = "wm,wm8505-fb"; + reg = <0xd8050800 0x200>; + display = <&display>; + default-mode = <&mode0>; + }; |