diff options
Diffstat (limited to 'Documentation/devicetree/bindings/serial')
5 files changed, 109 insertions, 9 deletions
diff --git a/Documentation/devicetree/bindings/serial/cdns,uart.txt b/Documentation/devicetree/bindings/serial/cdns,uart.txt new file mode 100644 index 000000000000..a3eb154c32ca --- /dev/null +++ b/Documentation/devicetree/bindings/serial/cdns,uart.txt @@ -0,0 +1,20 @@ +Binding for Cadence UART Controller + +Required properties: +- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps" +- reg: Should contain UART controller registers location and length. +- interrupts: Should contain UART controller interrupts. +- clocks: Must contain phandles to the UART clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: Tuple to identify input clocks, must contain "uart_clk" and "pclk" + See ../clocks/clock-bindings.txt for details. + + +Example: + uart@e0000000 { + compatible = "cdns,uart-r1p8"; + clocks = <&clkc 23>, <&clkc 40>; + clock-names = "uart_clk", "pclk"; + reg = <0xE0000000 0x1000>; + interrupts = <0 27 4>; + }; diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt index 3ca01336b837..8adbab268ca3 100644 --- a/Documentation/devicetree/bindings/serial/efm32-uart.txt +++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt @@ -6,7 +6,7 @@ Required properties: - interrupts : Should contain uart interrupt Optional properties: -- efm32,location : Decides the location of the USART I/O pins. +- energymicro,location : Decides the location of the USART I/O pins. Allowed range : [0 .. 5] Default: 0 @@ -16,5 +16,5 @@ uart@0x4000c400 { compatible = "energymicro,efm32-uart"; reg = <0x4000c400 0x400>; interrupts = <15>; - efm32,location = <0>; + energymicro,location = <0>; }; diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt index a1d1205d8185..c95005efbcb8 100644 --- a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -1,7 +1,11 @@ * Freescale low power universal asynchronous receiver/transmitter (lpuart) Required properties: -- compatible : Should be "fsl,<soc>-lpuart" +- compatible : + - "fsl,vf610-lpuart" for lpuart compatible with the one integrated + on Vybrid vf610 SoC with 8-bit register organization + - "fsl,ls1021a-lpuart" for lpuart compatible with the one integrated + on LS1021A SoC with 32-bit big-endian register organization - reg : Address and length of the register set for the device - interrupts : Should contain uart interrupt - clocks : phandle + clock specifier pairs, one for each entry in clock-names diff --git a/Documentation/devicetree/bindings/serial/samsung_uart.txt b/Documentation/devicetree/bindings/serial/samsung_uart.txt index 2c8a17cf5cb5..e85f37ec33f0 100644 --- a/Documentation/devicetree/bindings/serial/samsung_uart.txt +++ b/Documentation/devicetree/bindings/serial/samsung_uart.txt @@ -1,14 +1,58 @@ * Samsung's UART Controller -The Samsung's UART controller is used for interfacing SoC with serial communicaion -devices. +The Samsung's UART controller is used for interfacing SoC with serial +communicaion devices. Required properties: -- compatible: should be - - "samsung,exynos4210-uart", for UART's compatible with Exynos4210 uart ports. +- compatible: should be one of following: + - "samsung,exynos4210-uart" - Exynos4210 SoC, + - "samsung,s3c2410-uart" - compatible with ports present on S3C2410 SoC, + - "samsung,s3c2412-uart" - compatible with ports present on S3C2412 SoC, + - "samsung,s3c2440-uart" - compatible with ports present on S3C2440 SoC, + - "samsung,s3c6400-uart" - compatible with ports present on S3C6400 SoC, + - "samsung,s5pv210-uart" - compatible with ports present on S5PV210 SoC. - reg: base physical address of the controller and length of memory mapped region. -- interrupts: interrupt number to the cpu. The interrupt specifier format depends - on the interrupt controller parent. +- interrupts: a single interrupt signal to SoC interrupt controller, + according to interrupt bindings documentation [1]. + +- clock-names: input names of clocks used by the controller: + - "uart" - controller bus clock, + - "clk_uart_baudN" - Nth baud base clock input (N = 0, 1, ...), + according to SoC User's Manual (only N = 0 is allowedfor SoCs without + internal baud clock mux). +- clocks: phandles and specifiers for all clocks specified in "clock-names" + property, in the same order, according to clock bindings documentation [2]. + +[1] Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Optional properties: +- samsung,uart-fifosize: The fifo size supported by the UART channel + +Note: Each Samsung UART should have an alias correctly numbered in the +"aliases" node, according to serialN format, where N is the port number +(non-negative decimal integer) as specified by User's Manual of respective +SoC. + +Example: + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + +Example: + uart1: serial@7f005400 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005400 0x100>; + interrupt-parent = <&vic1>; + interrupts = <6>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART1>, <&clocks PCLK_UART1>, + <&clocks SCLK_UART>; + samsung,uart-fifosize = <16>; + }; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt index f13f1c5be91c..7f76214f728a 100644 --- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -4,9 +4,18 @@ Required properties: - compatible : "snps,dw-apb-uart" - reg : offset and length of the register set for the device. - interrupts : should contain uart interrupt. + +Clock handling: +The clock rate of the input clock needs to be supplied by one of - clock-frequency : the input clock frequency for the UART. +- clocks : phandle to the input clock + +The supplying peripheral clock can also be handled, needing a second property +- clock-names: tuple listing input clock names. + Required elements: "baudclk", "apb_pclk" Optional properties: +- resets : phandle to the parent reset controller. - reg-shift : quantity to shift the register offsets by. If this property is not present then the register offsets are not shifted. - reg-io-width : the size (in bytes) of the IO accesses that should be @@ -23,3 +32,26 @@ Example: reg-shift = <2>; reg-io-width = <4>; }; + +Example with one clock: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; + +Example with two clocks: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clocks = <&baudclk>, <&apb_pclk>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; |